GE Security UVP-CE3-D27N, UVPS-HE3-D27N, UVPS-HE3-D27P, UVPS-HE4-D27N, UVPS-HE4-D27P User Manual

...
0 (0)

UltraView PTZ

User Manual

Copyright

Disclaimer

Trademarks and

patents

Software license agreement

Copyright © 2011 UTC Fire & Security. All rights reserved.

This document may not be copied or otherwise reproduced, in whole or in part, except as specifically permitted under US and international copyright law, without the prior written consent from UTC Fire & Security.

Document number: 1069677C-EN (February 2011)

THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. UTC FIRE AND SECURITY ASSUMES NO RESPONSIBILITY FOR INACCURACIES OR OMISSIONS AND SPECIFICALLY DISCLAIMS ANY LIABILITIES, LOSSES, OR RISKS, PERSONAL OR OTHERWISE, INCURRED AS A CONSEQUENCE, DIRECTLY OR INDIRECTLY, OF THE USE OR APPLICATION OF ANY OF THE CONTENTS OF THIS DOCUMENT. FOR THE LATEST DOCUMENTATION, CONTACT YOUR LOCAL SUPPLIER OR VISIT US ONLINE AT WWW.INTERLOGIX.COM.

This publication may contain examples of screen captures and reports used in daily operations. Examples may include fictitious names of individuals and companies. Any similarity to names and addresses of actual businesses or persons is entirely coincidental.

Interlogix name and logo are trademarks of UTC Fire & Security. UltraView is a trademark of UTC Fire & Security.

UltraView PTZ is a trademark of UTC Fire & Security.

Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.

IImportant: This end-user license agreement (“Agreement”) is a legal agreement between UTC Fire & Security and You. Read the following terms and conditions carefully before installing or using this Software. This agreement provides a license from UTC Fire & Security to use the Software. It also contains warranty information, disclaimers, and liability limitations. Installing and/or using the Software confirms Your agreement to be bound by these terms and conditions. If You do not agree with these terms and conditions, do not install or use the Software or, if already installed, immediately cease all use of the Software and promptly uninstall all components of the Software.

Definitions. The following definitions apply to this document:

a.“UTC Fire & Security”, with respect to title to or warranty of the Software, means UTC Fire & Security Americas Corporation, Inc.

b.“Software” means SymNav, the executable software or firmware programs and accompanying documentation installed on the Interlogix products, plus any upgrades, modified versions, updates, additions, and copies of the software furnished to Customer during the term of the license granted herein.

c.“Documentation” means all associated media, printed materials, and electronic documentation accompanying the Software.

d.“Licensed Product” means the Software and Documentation.

e.“Customer” means the person or organization, or parent or subsidiary thereof, who uses the Software for its intended purposes, and excludes distributors, authorized resellers, value-added resellers and original equipment manufacturers. Customer may be referred to as You or Your, whether an individual or a business entity of any kind.

f.“Machine” means the computer, workstation, terminal, or other hardware product on which the Software is installed.

License. All rights to and in the Licensed Product, including, but not limited to, copyrights, patents, trademarks, and trade secrets, belong to UTC Fire & Security, and UTC Fire & Security retains title to each copy of the Software. You agree that UTC Fire & Security at any time, upon reasonable notice, may audit Your use of the Software for compliance with the terms and conditions of this Agreement. Subject to the terms and conditions of this Agreement, UTC Fire & Security grants You a nonexclusive license to use the Software, but only in the country where acquired, provided that You agree to the following:

iii

You may:

g.install and use the Software on a single Machine at one time, unless You have purchased additional copies of the Software, in which case You may install the software on the number of Machines for which You have purchased copies of the Software;

h.use the original copy of the Software provided to You for backup purposes.

You may not:

a.transfer or distribute the Licensed Product to others, in electronic format or otherwise, and this Agreement shall automatically terminate in the event of such a transfer or distribution;

b.use the Software over a computer network;

c.sell, rent, lease, or sublicense the Software;

d.copy or modify the Licensed Product for any purpose, including for backup purposes.

Term. This Agreement is effective until terminated. You may terminate this Agreement by uninstalling all components of the Software from all Machines and returning the Software to UTC Fire & Security. UTC Fire & Security may terminate this Agreement if You breach any of these terms and conditions. Upon termination of this Agreement for any reason, You agree to uninstall all components of the Software and return the Licensed Product to UTC Fire & Security. All provisions of this Agreement relating to (i) disclaimer of warranties; (ii) limitations on liability, remedies, and damages; and (iii) UTC Fire & Security’s proprietary rights, shall survive termination of this Agreement.

Object code. The Software is delivered in object code only. You may not alter, merge, modify, adapt, or translate the Software, nor decompile, disassemble, reverse-engineer, or otherwise reduce the Software to a human-perceivable form, nor create derivative works or programs based on the Software.

Limited warranty. UTC Fire & Security warrants that for one (1) year from the date of delivery of the Licensed Product (Software Warranty Period), the functions contained in the Software will be fit for their intended purpose as described in the applicable Documentation from UTC Fire & Security, and will conform in all material respects to the specifications stated in such Documentation. UTC Fire & Security does not warrant that the operation of the Software will be uninterrupted or error-free. UTC Fire & Security does warrant that the media on which the Software is furnished will be free from defects in materials and workmanship under normal use for a period of thirty (30) days from the date of delivery (Media Warranty Period). Except as specifically provided therein, any other software and any hardware furnished with or accompanying the Software is not warranted by UTC Fire & Security.

Your exclusive remedy under this limited warranty for nonconforming Software shall be repair or replacement of the Software, at the sole discretion of UTC Fire & Security. To obtain a repair or replacement of nonconforming Software, contact UTC Fire & Security Customer Service toll-free at 888-437-3287 or online at www.interlogix.com during the Software Warranty Period.

Except as expressly provided above, the licensed product is provided “as is” without warranty of any kind, either expressed or implied, including, but not limited to, implied warranties of merchantability or fitness for a particular purpose and, except as expressly provided above, You assume the entire risk as to the quality and performance of the licensed product.

Limitation of liability. UTC Fire & Security’s sole obligation or liability under this agreement is the repair or replacement of nonconforming software and/or defective media according to the limited warranty above. In no event will UTC Fire & Security be liable for damages, whether consequential, incidental, or indirect, nor for loss of data, loss of profits, or lost savings, arising from use or inability to use the software or documentation (or any hardware furnished with the software), even if UTC Fire & Security has been advised of the possibility of such damages, nor for any claim by any third party.

iv UltraView PTZ User Manual

General. Any materials provided to You by UTC Fire & Security shall not be exported or reexported in violation of any export provisions of the USA or any other applicable jurisdiction. Any attempt to sublicense, assign, or transfer any of the rights, duties, or obligations hereunder shall be void. This Agreement shall be governed by and interpreted under the laws of the State of New York, United States of America, without regard to conflicts of law provisions. You hereby consent to the exclusive jurisdiction of the state and federal courts located in Multnomah County, Oregon, to resolve any disputes arising under or in connection with this Agreement, with venue in Portland, Oregon.

Restricted rights legend. The Licensed Product is provided with RESTRICTED RIGHTS. In the event the United States Government or an agency thereof is granted a license, the following additional terms apply: Restricted Computer Software, as defined in the Commercial Computer Software–Restricted Rights clause at Federal Acquisition Regulations 52.227-19, and the restrictions as provided in subparagraphs (c)(1) and (c)(2) thereof; and as applicable, the Government’s rights to use, modify, reproduce, release, perform, display, or disclose the Software also are restricted as provided by paragraphs (b)(2) and (b)(3) of the Rights in Noncommercial Technical Data and Computer Software–Small Business Innovative Research (SBIR) Program clause at DFARS 252.227-7018.

Acknowledgment. You acknowledge that You have read and understand this agreement and agree to be bound by its terms. You further agree that this agreement is the complete and exclusive statement of the agreement between You and UTC Fire & Security, and supersedes any proposal or prior agreement, oral or written, and any other communication relating to the subject matter of this agreement.

Intended use Use this product only for the purpose it was designed for; refer to the data sheet and user documentation. For the latest product information, contact your local supplier or visit us online at www.interlogix.com.

Manufacturer UTC Fire & Security Americas Corporation, Inc. 2955 Red Hill Ave, Costa Mesa, CA 92626, USA

Certification

FCC compliance

ACMA compliance

N4131

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Notice! This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Canada This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

EU Directives 2004/108/EC (EMC Directive). Non-European manufacturers must designate an authorized representative in the Community. Our authorized manufacturing representative is UTC Fire & Security B.V., Kelvinstraat 7, 6003 DH Weert, Nederland.

2004/108/EC (EMC Directive): Hereby, UTC Fire & Security declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2004/ 108/EC.

v

2002/96/EC (WEEE directive). Products marked with this symbol cannot be disposed of

as unsorted municipal waste in the European Union. For proper recycling, return this

product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information, visit www.recyclethis.info.

Contact information For contact information, see www.interlogix.com.

vi UltraView PTZ User Manual

vii

Contents

Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Conventions used in this document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Safety terms and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Chapter 1. Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Menu navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Programming shortcuts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Accessing programming menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Menu navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Top-level access and information screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Memory management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Program select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Presets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Titles/areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Current status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Tours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Additional menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Exposure control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Chapter 2. Troubleshooting and support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Common issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Contacting us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Online . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Appendix A. Defaults and hazardous materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Toxic and hazardous element levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

viii UltraView PTZ User Manual

ix

Preface

This is the Interlogix UltraView PTZ User Manual. This document includes an overview of the product and detailed instructions explaining:

how to access the menus; and

how to customize the settings.

There is also information describing how to contact technical support if you have questions or concerns. To use this document effectively, you should have a basic knowledge of CCTV systems and components.

Read these instructions and all ancillary documentation entirely before installing or operating this product. The most current versions of this and related documentation may be found on our website at www.interlogix.com.

Note: A qualified service person, complying with all applicable codes, should perform all required hardware installation.

Conventions used in this document

The following conventions are used in this document:

Bold

Menu items and buttons.

 

 

Italic

Emphasis of an instruction or point; special terms.

 

 

 

File names, path names, windows, panes, tabs, fields, variables, and other GUI elements.

 

 

 

Titles of books and various documents.

 

 

Blue italic

(Electronic version.) Hyperlinks to cross-references, related topics, and URL addresses.

 

 

Monospace

Text that displays on the computer screen.

 

Programming or coding sequences.

 

 

Safety terms and symbols

These terms may appear in this manual:

CAUTION: Cautions identify conditions or practices that may result in damage to the equipment or other property.

WARNING: Warnings identify conditions or practices that could result in equipment damage or serious personal injury.

x UltraView PTZ

User Manual

Chapter 1 Programming

This chapter provides an overview of your UltraView PTZ menu system, including steps you may want to perform before you begin using your UltraView PTZ.

In this chapter:

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Menu navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Accessing programming menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Menu navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Top-level access and information screens . . . . . . . . . . . . . . . . . . . . . . . . .6

Memory management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Program select. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Presets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Titles/areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Current status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Tours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Additional menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Exposure control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

2 UltraView PTZ

User Manual

Introduction

This manual contains programming instructions for the UltraView PTZ series pan/tilt/zoom cameras (Figure 1). The most common UltraView PTZ programming options and screen sequences are illustrated. Notations indicate where options may differ among camera models.

Figure 1. UltraView PTZ dome with wall-mount arm

UltraView PTZ supports many protocols to work with various keypad controllers, DVRs, and other video surveillance equipment. Please refer to Appendix B of the UltraView PTZ Installation Manual for the details on supported protocols.

Chapter 1 3

Programming

Menu navigation

We use the KTD-405 keypad controller (Figure 2) in this manual to explain the features of UltraView PTZ because of the KTD-405’s ability to control all of the UltraView PTZ’s advanced features. (For detailed keypad instructions, refer to the KTD-405/KTD-405A/KTD-405-2D Controller Keypad User Manual.)

Figure 2. Navigating with a KTD-405/405A/KTD-405-2D keypad

 

 

Shaded keys

 

Numeric keys

Select

appear on the

Advance

KTD-405A only

 

 

 

 

 

 

 

 

 

Scroll up

 

ZONE 32

 

PARKING GARAGE

 

1ST

focus

 

 

 

CAMERA 22

MONITOR 2

 

 

auto

 

 

 

 

 

 

Previous

Next

 

 

 

 

 

 

 

last

 

 

mon

view

zone

dsr/vcr

aux 1

aux 2

aux 3

aux 4

 

 

1

A

2

B

3

C

seq

alarm

tour

store

find

 

 

 

 

 

4

D

5

E

6

 

face

badge

over

vol

vol

+

zoom

-

 

Edit (turn

7

 

8

 

9

 

 

 

 

 

 

+

focus

-

 

joystick

 

 

 

 

 

 

 

 

Scroll down

clockwise)

clear

 

 

set

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

esc

 

 

 

 

 

 

 

 

 

 

+

iris

-

 

 

Select

 

 

Previous

 

 

Next

 

Change setting

 

 

 

 

 

 

 

 

Scroll up

 

Scroll down

 

 

 

 

 

 

You can use multiple methods to navigate through the menu system with your keypad:

Joystick navigation. Use the keypad joystick to move through menu items. When you have the desired menu item selected, move the joystick to the right to advance through the available options. Once you are in a menu, move the joystick to the left to back out of that menu.

Button navigation. Use the pause button to scroll up; play to scroll down; fast forward or forward frame for the next item; fast rewind or reverse frame for the previous item. When you have navigated to the item you want, use seq, set, or fast forward to select that item. The arrow indicator on the UltraView PTZ menu identifies the property that will be changed.

To change a setting, press the iris + button. The setting will be saved when you advance to the next menu. Alternatively, you may be able to use the zoom + button to advance, depending on your protocol. (Use of shortcuts on the KTD-405 keypad to navigate and select may not work with all protocols.)

Numerical navigation. Press the number associated with a menu item to select or highlight that option or proceed to that menu. You will also use the number keys to enter numerical data, such as passwords.

Note: When you press the number associated with an option and there is a value to set, you will automatically be asked to set that value. If there is no value to set, when you press the number associated with an option, that option will be selected and you will proceed to the next menu.

4 UltraView PTZ

User Manual

Programming shortcuts

This section lists the keypad programming shortcuts for presets and tours. For detailed instructions, refer to the

KTD-405/KTD-405A/KTD-405-2D Controller Keypad User Manual.

Presets:

To store: Position the camera. Press the store key and then enter the preset number. Press store again.

To call up: Press find and enter the preset number.

Shadow Tours:

To store: Press and hold the esc key and then press the tour key. Then press the + side of the zoom, focus, or iris key to start recording a shadow tour. Athe end of the shadow tour, press esc.

Accessing programming menus

To access the programming menus using the keys on a KTD-405 keypad, do the following:

1.Switch the keypad to the camera site you want to program.

2.Press and hold the set key until Enter programming code displays.

3.At the code entry display, enter the programming code 9, 5, 1. Then press the seq button.

4.At the first menu display, press 3.

5.At the Enter camera site number screen, enter the site number of the camera you wish to program.

At this point, you have access to the UltraView PTZ programming menus. For more information on the programming menus, see Menu navigation on page 5.

Note: If you are prompted to enter a password, refer to Passwords on page 33 for the default pass code key.

GE Security UVP-CE3-D27N, UVPS-HE3-D27N, UVPS-HE3-D27P, UVPS-HE4-D27N, UVPS-HE4-D27P User Manual

Chapter 1 5

Programming

Menu navigation

The UltraView PTZ menu structure generally follows an alphabetical order (in English) of the functions and features that can be set with a few exceptions. Table 1 shows the order of the menu screens and their relationship to each other, as well as the options and defaults for each screen.

Table 1. UltraView PTZ menu hierarchy

Password (page 6).

Product information (page 6). System information (page 6). Memory management (page 7).

Copy housing to PTZ

Copy PTZ to housing

Program select (page 8).

Setup (page 8)

Clear memory (page 8).

Automatic slow shutter (page 9).

Autopan speed (page 9).

Auto Return (page 10).

Azimuth indicator (page 10).

Day/night switch (page 12).

Electronic zoom (page 12).

Exposure control (page 13).

Image freeze (page 13).

Image stabilization (page 13)

Lens initialization. (page 14)

Lift/gain (page 14).

Max tilt/pan speed (page 15).

Preset speed (page 15).

Proportional speed (page 16).

Quick spin (page 16).

Serial update (page 16)

Shutter speed (page 17). NTSC.

Shutter speed (page 17). PAL.

Site number display (page 17).

Synchronization (page 18).

Temperature display (page 18).

White balance (page 19).

Wide dynamic range (WDR) (page 19).

Zoom speed control (page 19).

Zoom variable tilt (page 20)

Presets (page 20).

Titles/areas (page 21).

Preset titles.

Area and titles.

Camera title.

Tour title.

Current status (page 26).

Tours (page 27).

ShadowTours (page 27).

Preset tours (page 29).

Additional menus (page 31).

Privacy masks (page 31).

Alarms and relays (page 32)

System startup (page 33)

Password protection

Installation date

Power-up action

Position reporting

6 UltraView PTZ

User Manual

Top-level access and information screens

When you access the UltraView PTZ series, the following three menus display:

Password. The camera will come from the factory with the default password turned off, but saved in memory. See Passwords on page 42 for details. If you have previously input some information to set up the camera and have passwords enabled, you will be prompted to enter your password (Figure 3) to proceed. Use the directional buttons to navigate to the numbers, and press iris + to input those numbers. Input the wrong password and you will automatically exit the menu. If the password is correct, you will proceed to the Product information screen.

Figure 3. Password screen

ULTRAVIEW PTZ

Product information. This screen (Figure 4) provides product information, including:

Product name

Camera type

Site ID number

Unit serial number

Installation date (This should be set by the installer.)

Video format

Protocol

There are no customizable options on this screen. Go to the next screen by pressing fast forward on the keypad.

System information. This screen (Figure 5) provides information pertaining to the current software, hardware, and installation information.

P = Type and version date for the pan processor. T = Type and version date for the tilt processor. B = Camera type and firmware version.

I = Type and version date for the housing card.

Note: If you see no type and version date info, verify proper connections, mounting, and presence of the housing card. If there is no housing card, you will see the message,

“I: NOT INSTALLED.”

Figure 4. Product information for UltraView PTZ

ULTRAVIEW PTZ

DAY/NIGHT 27X WDR

-- SITE 0083 --

SERIAL : INSTALLATION :

VIDEO FORMAT : NTSC

PROTOCOL :

 

EXIT HOLD SEQ

NEXT

Figure 5. System Information for UltraView PTZ

ULTRAVIEW PTZ

091217

091217 B: LM703n-8 V 1.48

There are no customizable options on this screen. Go to the next screen by pressing fast forward on the keypad.

Chapter 1 7

Programming

Memory management

If the settings stored in the memory of the housing differ from the settings stored in the memory of the camera (PTZ), Memory will flash on your monitor. When you log on, you will see the Memory management menu (Figure 6) asking you to choose which settings you want. The settings you choose overwrite any existing settings. Until you decide which settings to use, the unit will use the settings stored in the camera. Once the settings have been successfully transferred, Memory will stop flashing on the monitor.

The Memory management screen appears after the System information screen in the menu sequence. So if the memory message is flashing, the menu order will be Product information, System information, Memory management, Program select.

Figure 6. Memory flashing menu

Note: DIP switch settings on the camera can be set to automatically copy the settings from the housing, or push the settings from the camera to the housing. See the UltraView PTZ Installation Manual for more information.

Loading...
+ 39 hidden pages