Genie 7035, 3055, 7033, 7053, 7055 User Manual

Name: Genie 7035
Brand: Genie
SKU: 2497975
Rating: 4 (2 reviews)

...

4 (2)

1035, 2033, 2035, 2036, 2053, 2055, 3033, 3035,

3053, 3055, 7033, 7035, 7053, 7055

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER

HOMEOWNER: SAVE THIS MANUAL FOR FUTURE REFERENCE

BELT/CHAIN DRIVE GARAGE DOOR OPENER MODELS

PROGRAMMING, OPERATION

& MAINTENANCE MANUAL

Includes

INTELLICODE

Remote Control.

The Included

Safe-T-Beam® system

MUST be installed to close the door. DO NOT use other brands or types.

For use with residential sectional overhead garage doors ONLY.

Homelink® and Car2U® compatible

Beam, are trademarks of The Genie Company. All other trademarks are property of their rightful owners. Consistent with our policy of continu-

ing product improvements, we reserve the right to change product speci cations without prior notice or obligations. HomeLink is a registered

trademark of Gentex Corporation. Car2U is a registered trademark of Lear Corporation.

Patents www.GenieCompany.com/patents

38967503545_EnglishWeb 09/2017

STOP

DO NOT return product to store,

visit www.GenieCompany.com

or call Customer Service at: 1-800-35-GENIE,

For SilentMax Connect® Models, call 1-866-599-4995

To reduce the risk of injury to persons or damage to property, use this opener only with a sectional residential door.

WARNING

Por reduire le risque de blessures ou de dommages materials, utillsez cet ouvre-porte uniquement pour une porte

a section re sidentielie.

AVERTISSEMENT

Safety Information

Safety Noti cations ................................................. 4

Important Safety Instructions ............................. 5

Features

Safety Features ......................................................... 6

Opener Features ...................................................... 6

Programming Information

Introduction .............................................................. 7

Overview of Powerhead Controls...................... 7

Travel Limits

Closing Garage Door (DOWN Limit) ................. 8

Opening Garage Door (UP Limit)....................... 9

Force Control ...........................................................10

Contact Reverse Test ............................................10

Contact Reverse Adjustment ............................10

Remote Control Programming .........................11

Maintenance and Adjustments

Important Safety Instructions ...........................12

Regular Maintenance ...........................................13

Remote Battery Replacement ...........................13

Light Bulb Replacement .....................................14

Chain/Belt Tension ................................................14

Carriage Adjustment for Release .....................15

Adjustment Guides ...............................................15

Resetting Travel Limits .........................................15

Locating Safe-T-Beam® Pairs

.............................16

Wire Diagram ..........................................................16

Troubleshooting ........................................... 17-18

Genie Battery Backup Installation ..............19

Optional Programming & Accessories

Clearing Memory for Remotes .........................20

Programming Vehicle Remotes ........................21

Programming Wireless Keypad .................22-23

Parts ................................................................... 24-27

DASMA Information ................................... 28-31

Warranty ..................................................................32

INDEX

SAVE THESE INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

FCC Part 15.21 Statement:

Changes or modi cations not expressly

approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

FCC / IC Statement:

This device complies with FCC Part 15

and Industry Canada licence-exempt RSS

standard(s). Operation is subject to the

following two conditions: (1) this device

may not cause harmful interference, and

(2) this device must accept any interference

received, including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux CNR

d’Industrie Canada applicables aux appareils

radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes : (1)

l’appareil ne doit pas produire de brouillage,

et (2) l’utilisateur de l’appareil doit accepter

tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le

fonctionnement.

DO NOT RETURN PRODUCT TO STORE

If you require assistance or have any questions,

a knowledgeable Genie Service Technician is just

a phone call away at:

1-800-35-GENIE (1-800-354-3643)

Or visit our website at:

www.GenieCompany.com

Thank you for purchasing a

Genie® brand garage door

opener. The leader in garage door

opener technology.

Before setting up your new garage door opener, please locate and record the model plate on the

opener. This information will be necessary should you seek technical support via our website,

customer support department or local servicing Genie dealer.

Model Number:______________________________

Serial Number:_______________________________

1 Bulb Models

2 Bulb Models

Please take a moment to preview this manual and assembly poster

to ensure that you have the proper tools and skill set to install a new

garage door opener. Pay particular attention to all Safety Warnings,

Cautions and Information. Remember, your garage door is the largest

and heaviest moving object in your home.

START WITH ASSEMBLY POSTER THEN RETURN TO THIS MANUAL

NOTE

Keep an original or photocopy of receipt of

opener purchase for warranty purposes.

SAFETY NOTIFICATIONS & INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

OVERVIEW OF POTENTIAL HAZARDS

READ THIS SAFETY INFORMATION

Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension,

and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual. If you have questions or do

not understand the information presented, call your nearest trained door system technician or visit our website at www.geniecompany.com.

CONVENTIONS USED IN THESE INSTRUCTIONS

The following safety alert symbol and signal words are used throughout this manual to call attention to and identify di erent levels of hazards and special

instructions.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert

symbol and the word

“DANGER”, “WARNING”,

“CAUTION”.

•

DANGER

indicates an imminently hazardous situation which, if NOT avoided, will result in death or serious injury.

•

WARNING

indicates a potentially hazardous situation which, if NOT avoided, could result in death or serious injury.

•

CAUTION

indicates a potentially hazardous situation which, if NOT avoided, may result in injury or property damage.

•

The word

NOTE

s used to indicate important steps to be followed or important considerations.

Tous les messages concernant la sécurité seront indiqués après un symbole d’alerte de la sécurité et l’une des mentions suivantes “DANGER”,

”AVERTISSEMENT” ou “MISE EN GARDE”.

• DANGER signale une situation dangereuse imminente qui, si elle n’est pas évitée, risque d’entraîner des blessures graves, voire mortelles.

• AVERTISSEMENT signale une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque d’entraîner la mort ou des blessures

graves.

• MISE EN GARDE signale une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque d’entraîner des blessures ou des

dommages matériels.

• Le terme REMARQUE est utilisé pour signaler les étapes importantes à suivre ou d’importants éléments à prendre en considération.

IMPORTANTES CONSIGNES DE SÉCURITÉ

DANGER POTENTIEL EFFET PRÉVENTION

PORTE EN MOUVEMENT

AVERTISSEMENT

Pourrait entraîner des

blessures graves voire la mort

Utiliser uniquement si la porte est en vue et libre de tout obstacle.

Ne laisser personne se tenir dans l’ouverture de la porte pendant

qu’elle est en mouvement.

Ne pas permettre aux enfants de jouer avec l’opérateur de la porte.

Ne pas modi er la commande de l’opérateur à contact momentané

à moins qu’un moyen d’inversion externe soit installé.

Ne pas faire fonctionner une porte qui bloque ou dont le ressort

est cassé.

CHOC ÉLECTRIQUE

AVERTISSEMENT

Pourrait entraîner des

blessures graves voire la mort

Couper le courant avant d’enlever le couvercle de l’opérateur.

Lorsque le couvercle doit être remplacé, s’assurer que les  ls ne sont

ni coincés ni près des pièces mobiles.

L’opérateur doit être correctement mis à la terre.

TENSION ÉLEVÉE RESSORT

AVERTISSEMENT

Pourrait entraîner des

blessures graves voire la mort

Ne pas essayer d’enlever, réparer ni ajuster les ressorts ou

toute autre pièce à laquelle le ressort de la porte est attaché, y

compris blocs de bois, supports en acier, câbles ou autres articles

semblables.

Les réparations et les réglages doivent être e ectués par

technicien quali é qui se sert d’outils appropriés et qui respecte les

instructions.

POTENTIAL HAZARD EFFECT PREVENTION

MOVING DOOR

WARNING

Could result in Serious

Injury of Death

Do Not operate unless the doorway is in sight and free of

obstructions. Keep people clear of opening while door is moving.

Do Not allow children to play with the door opener.

Do Not change opener control to momentary contact unless and

external reversing means is installed.

Do Not operate a door that jambs or one that has a broken spring.

ELECTRICAL SHOCK

WARNING

Could cause Serious

Injury or Death

Turn o electrical power before removing opener cover.

When replacing the cover, make sure wires are not pinched or near

moving parts.

Opener must be electrically grounded.

HIGH SPRING TENSION

WARNING

Could cause Serious

Injury or Death

Do Not try to remove, repair or adjust springs or anything to which

door spring parts are fastened such as wood block, steel brackets,

cables or any other structure or like item.

Repairs and adjustments must be made by a trained service

representative using proper tools and instructions.

IMPORTANT INSTALLATION INSTRUCTIONS

IMPORTANTES INSTRUCTIONS D’INSTALLATION

WARNING

Opener is equipped with grounded electrical plug for

your protection, and only  ts grounded electrical

outlets. DO NOT alter plug in any way! If your have no

grounded outlets, have one installed by a licensed

electrician. Opener must be properly grounded to prevent

personal injury and equipment damage. NEVER USE AN

EXTENSION CORD! Check local building codes for any

requirement that you must have a permanent hard-wired

connection. Permanent hard-wired connections must be

performed by a licensed electrician using proper tools and

instructions.

AVERTISSEMENT

L’opérateur, qui est équipé d’une prise électrique mise à la terre

pour votre protection est compatible uniquement avec des

prises électriques mises à la terre. NE PAS modi er la  che dune

quelconque manière. Si vous n’avez pas de prises mises à la terre,

faites-en installer par un électricien agréé. L’opérateur doit être

correctement mis à la terre pour éviter les blessures corporelles et

des dommages matériels. NE JAMAIS UTILISER DE RALLONGE!

Véri ez les codes locaux des bâtiments pour connexions câblées

permanente. Les connexions câblées permanentes doivent

être e ectuées par un électricien agréé qui se servira d’outils

appropriés et respectera les consignes.

WARNING

TO REDUCE THE RISK OF SEVERE INJURY OR

DEATH

READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. If you have any questions or do not

understand an instruction, call The Genie Company.

• DO NOT install opener on an improperly balanced door. An improperly balanced door could cause severe injury. Repairs

and adjustments to cables, spring assembly and other hardware must be made by a trained service person using proper

tools and instructions.

• Remove all ropes, and disable all locks connected to the door before installing opener.

• Where possible, install the door opener 7 feet or more above the  oor. For products having an emergency release,

mount the emergency release within reach, but at least 6 feet above the  oor and avoiding contact with vehicles to

avoid accidental release. DO NOT use emergency release cord to pull door.

• DO NOT connect the opener to the source of power until instructed to do so.

• Locate the wall control button: A) Within sight of door. B) At a minimum height of 5 feet, so small children cannot reach

it. C) Away from all moving parts of the door.

• Install the entrapment WARNING label next to the wall button or console, in a prominent location. Install the emergency

release handle on the emergency release cord.

• The opener must reverse when the door contacts a 1-1/2 inch high object on the  oor at the center of the doorway. This

is about the size of a 2” x 4” board laid  at.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES DE BLESSURES GRAVES VOIRE

MORTELLES

LIRE ET SUIVRE ATTENTIVEMENT TOUTES LES INSTRUCTIONS D’INSTALLATION ET DE FONCTIONNEMENT AINSI QUE TOUTES LES CONSIGNES

DE SÉCURITÉ. Si vous avez des questions ou si vous ne comprenez pas une instruction, veuillez contacter directement The

Genie Company.

• NE PAS installer l’opérateur sur une porte mal équilibrée. Celle-ci pourrait entraîner de graves blessures. Les réparations

et les réglages des câbles, ensembles de ressort ou tout autre article de quincaillerie doivent être e ectués par un pro-

fessionnel qui se sert d’outils appropriés et qui respecte les instructions.

• Enlever toutes les cordes et désactiver toutes les verrous de la porte avant l’installer l’opérateur.

• Dans la mesure du possible, installer l’ouvre-porte à 2,1 m ou plus au-dessus du sol. Pour les produits dotés d’un cordon

de déclenchement d’urgence, installer le déclenchement d’urgence mais au moins à 1,8 m au-dessus du sol en évitant

tout contact avec les véhicules pour éviter qu’ils ne soient déclenchés accidentellement. NE PAS utiliser d’urgence cor-

don de libération pour ouvrir ou fermer la porte.

• NE PAS connecter l’opérateur à la source d’alimentation tant que l’instruction n’est pas donnée.

• Repérer la console murale: A) En vue de la porte. B) À une hauteur minimale de 1,5 m a n que les jeunes enfants ne

puissent pas l’atteindre. C) Loin de toutes pièces mobiles de la porte du garage.

• Placer l’étiquette d’AVERTISSEMENT en cas de coinçage à proximité du bouton mural ou de la console de manière à ce

qu’elle soit bien en évidence. Installer la poignée du cordon de déclenchement d’urgence.

• L’opérateur doit s’inverser lorsque la porte entre en contact avec un objet d’une hauteur de 3,8 cm placé sur le sol, au

centre de l’ouverture de la porte. Ceci équivaut environ à une planche de 5 x 10 cm posée à plat sur le sol.

Safe-T-Beam® (STB) Non-Contact

Reversing System

Puts an invisible beam across the door opening. The

door stops and reverses to the full open position if

anything passes through the beam. LED indicator

lights on the powerhead and on the STBs provide

self-diagnostics if an operational problems exists.

Door Detect™ Monitoring System

Monitors the Safe-T-Beam® system to ensure proper

functionality and will automatically stop and

reverse a closing door if a problem is detected.

Safe-T-Reverse® Contact Reversing System

Automatically stops and reverses a closing door

within two seconds of contact with an object.

Manual Emergency Release

Manually releases door from door opener. Used during a power failure or other emergency to allow manual opening and closing of door.

DO NOT use emergency release cord to pull door

SmartSet

Electronic Programming

Easily adjust the programming to set limits and program new remotes.

Automatic Lighting System

Single or Dual Bulb lighting system supplies light for safer evening exits and entries. Turn ON when door is activated and automatically

turns OFF 4 minutes later.

Intellicode®

An encryption system that enhances the security of the door opener by continuously changing the access code

each time the remote is used. The door opener responds to each new code only once. An access code copied from

a working system and tried again, will not control the door opener.

Wall Console (With select models)

Operates door opener from inside garage. The wall console has an indicator light with:

Open/Close, Sure-lock™, and independent light control buttons.

1.) Indicator Light

Large white button will display Red when wall console is properly wired and Sure-Lock™ is OFF. When Sure-Lock™

is ON, this light is o .

2.) Open/Close Button

Use this button to open or close garage door. When Sure-Lock™ is ON the Open/Close button will CLOSE the door

only.

NOTE: Constant button pressure in the CLOSE mode will override STB fault in the powerhead and close door.

3.) Independent Light Control Button

Use this button to turn the powerhead lights ON. Powerhead lighting will remain ON until this button is pressed

again or a door action has been completed.

4.) Sure-Lock™ Button

When Sure-Lock™ is ON, and the door is closed, the powerhead cannot be activated by the wall console or a

remote.

• Slide switch up to activate Sure-Lock™ (red light goes o ).

• Slide switch down to turn Sure-Lock™ OFF (red light goes on).

Home Link® and Car2U® compatible. See instructions in this manual, refer to the motor vehicle manual or visit

www.geniecompany.com for instructions.

Factory Programmed Remote Control

For ease and speed of installation, the remote included with this opener comes from the factory, pre-programmed.

No additional steps are required to activate the door using the remote.

Genie Battery Backup (BBU)

Available on some models. Provides power to opener in the event of a power failure.

NOTE: Genie Battery Backup will only operate after opener installation is completed and Travel Limits have been

set.

DO NOT INSTALL BATTERY BACKUP UNTIL OPENER IS FULLY INSTALLED AND PROGRAMMED

Safe-T-Beam® (STB) FUNCTION

1. The Safe-T-Beam® has no e ect on the door during an opening cycle.

2. If the Safe-T-Beam® detects an obstruction when trying to close the

door, it will not allow the door to close.

3. When the garage door is closing, if Safe-T- Beam® is interrupted by

a person or obstacle, the garage door will stop its downward travel

and reverse automatically to its fully opened position.

4. If the Safe-T-Beam® System fails, loses power, or is installed

improperly, press and hold the wall console “open/close” button

until the door reaches its fully closed position. If you release

the “open/close” button on the wall console during the closing

movement, the door will reverse automatically to its fully-opened

position.

SAFETY & STANDARD FEATURES

1 & 2

NOTE:

Before programming the opener, check to make sure there

are no objects in the garage door opening.

INTRODUCTION

Now that the Genie® garage door opener is installed, follow

the steps in this manual to program the opener so that

the door opens and closes properly and all remote devices

operate correctly. The following steps are a guide to setting

opener so it functions properly.

The following steps list the order of programming the

opener’s functional settings for use.

1. “TRAVEL LIMITS”

2. “FORCE CONTROL”

3. “REMOTE PROGRAMMING”

OVERVIEW OF POWERHEAD CONTROLS

This section describes the programming functions of the

opener. Use the following information to understand the

buttons and LED indicators used to program functions.

Powerhead: There are 3 programming buttons and 2 LED

lights on the powerhead. Each of the buttons are used to

enter and complete the setup programming. The LED lights

indicate status or a function change by illuminating ON, OFF,

or ON FLASHING.

There are 3 programs:

1. Door Travel Limits.

This program is used to set how far the door travels up

and down.

2. Force Setting Program.

This program controls the force applied during the

closing and opening of the door. They are factory set

and will rarely require adjustment.

3. Remote Programs (default menu)–only required for

added remote control transmitters.

Describes how to program remotes to sync with

additional remote control devices, wall consoles,

keypads and the powerhead.

NOTE: The 3 programming buttons are for programming ONLY.

These buttons can NOT be used to operate the opener once the

Required Programming section has been successfully completed.

Term De nitions:

Travel Limits Programmable setting to adjust how far door

travels up or down.

Force Control refers to how much power is needed to

move (open/close) a particular door and does NOT require

programming.

Remote Programming synchronizes remote devices

(remote and keypad) with the powerhead.

Open Travel

Button

Close Travel

Button

Long LED

Indicator

Round LED

Indicator

Program

Moves door up or down during

programming and advances

through menus.

Enters into and selects

programming menus.

• Just remember—the pointed end of the button (like an

arrowhead) points in the direction the carriage will move when

that button is pushed.

NOTE:

Each programming step has a 30 second time limit for completion

after the function is initiated. After 30 seconds, two LED’s will illuminate RED

indicating time has expired and the step must be re-started. Restart the step

as many times as necessary to complete the programming.

2 Light Models 1 Light Models

DOOR

ORIENTATION

Standing under the opener’s powerhead – facing the door – looking

up – this is the view you will see of the programming buttons and

LEDs.

Open Travel

Button

Close Travel

Button

Long LED

Indicator

Round LED

Indicator

Program

OPENER PROGRAMMING

WARNING

• Make sure doorway is in full view and clear of obstacles and

people to avoid injury or property damage.

• DO NOT operate this unit from the wall control before LIMITS

are set. Severe damage to the opener could occur.

• The carriage MUST be engaged to turnbuckle BEFORE setting

limits. See installation poster or call Customer Service at

1-800-35-GENIE or visit www.GenieCompany.com.

• DO NOT set limits with Battery Backup attached. AC power

MUST be connected to the opener while setting limits for

proper operation.

AVERTISSEMENT

• S’assurer que le passage de la porte est visible et dégagé, à

savoir sans obstacles ni personne a n d’éviter toute blessure

potentielle ou dommage matériel.

• NE PAS utiliser cette unité avec la console murale avant

d’avoir réglé les LIMITES. L’ouvre-porte pourrait subir de

sérieux dommages.

• La tendeur DOIT être engagée dans le chariot AVANT de

régler les limites. Voir le poster d’installation (si fourni) ou

appelez le service clientèle au 1-800-35-GENIE ou visitez le

site www.GenieCompany.com.

• NE PAS  xer de limites en mode batterie de secours.

L’alimentation CA DOIT être branchée sur l’ouvre-porte,

pendant le réglage des limites, pour assurer un bon

fonctionnement.

1. Press and hold the DOWN arrow button.

• Long LED will light BLUE.

2. Release DOWN arrow button.

• Long LED will  ash BLUE.

3. Press and hold the DOWN arrow button until

door is fully closed.

• Use the UP arrow button if door closes too

far. Use both UP and DOWN buttons to adjust

close travel as necessary.

Door should rest on the  oor until the weather strip

is compressed enough to seal along the width of the

door. Damaged doors or uneven  oors may not seal

properly. Repair these conditions to achieve a proper

seal. DO NOT compress seal so much that the door will

bend or buckle.

4. Press and release the SET/PRGM button

• Both LEDs will  ash BLUE then go out.

The DOWN limit is now programmed.

Steady Blue

HOLD

UNTIL

LED

Lights

Flashing Blue

RELEASE

1-2. Enter Programming Mode

3. Adjust Door Position

Programming DOWN Limit:

NOTE:

Carriage should be locked

to opener. Door should rest somewhere

between full open and closed. Do not start

with door fully open or closed.

4. Lock Programming

Flashing Blue

PRESS

RELEASE

PROGRAMMING DOWN TRAVEL LIMIT

PROGRAMMING UP TRAVEL LIMIT

Steady Blue

HOLD

UNTIL

LED

Lights

Flashing Blue

RELEASE

1-2. Enter Programming Mode

3. Adjust Door Position

4. Lock Programming

Flashing Blue

PRESS

RELEASE

1. Press and hold the UP arrow button.

• Long LED will light BLUE.

2. Release UP arrow button.

• Round LED will  ash BLUE.

3. Press and hold the UP arrow button until door is

fully open.

• Use the DOWN arrow button if door opens too

far. Use both UP and DOWN buttons to adjust

open travel as necessary.

Door should fully open so that door seal is even with

door header. Do Not adjust so much that the door will

bend or buckle or stretch door spring cables backward.

4. Press and release the SET/PRGM button

• Both LEDs will  ash BLUE then go out.

The UP limit is now programmed.

Programming UP Limit:

Force Control

The force controls are automatically set when the

wall control is used for the  rst time with garage

door opener. The door MUST complete one full cycle, from full

open to full close and then, full close to full open, before the

settings are automatically recorded.

Contact Reverse Test

NOTE:

The limit and Force settings MUST BE COMPLETED

before performing the Contact Reverse Test.

Force Control Adjustments

Force settings are programmed from the factory to

remain within safe parameters. These should not

require adjustments. However, certain circumstances

may require adjustment. See section 4 Maintenance

and Adjustments for detailed instructions pertaining

to the adjustment of force controls.

WARNING

TO AVOID INJURY OR DAMAGE

• NEVER adjust the force settings to adjust for damage,

including an unbalanced door, binding door track or

broken spring.

• Perform a CONTACT REVERSE TEST monthly.

AVERTISSEMENT

Pour éviter les blessures ou des dommages

• NE JAMAIS régler la force pour compenser des dommages,

y compris une porte mal équilibrée, un rail de porte coinçant

ou des ressorts cassés.

• Tous les mois, EFFECTUEZ LE TEST D’INVERSION AU CONTACT.

1. Press and release the Wall Control button and

allow the garage door to travel and stop at the

DOWN limit.

2. Press and release the wall control button and

allow the garage door to travel and stop at the

UP limit.

1. With the garage door open, lay a 2 X 4 board

 at on the  oor at the center of the door

opening.

2. Close the garage door using the wall control.

• When the door contacts the board, it should

stop and reverse direction within 2 seconds to

the full open position.

• The long LED light on the powerhead will begin

to  ash RED with the reversal of the door.

• Remove the 2” x 4” board and operate the

opener with the wall control again. This cycle

will clear the  ashing red LEDs.

Contact Reverse Adjustment

If the door stops before contacting the board or if it

does not reverse direction to fully open after contact

with the board, it may be due to an improperly set

DOWN limit. Verify settings by:

1. Repeat the “Down Travel Limit” section to make

certain the door is closing tight against the  oor.

2. Repeat the “Force Control” section on the left to

set force limits.

3. Repeat the “Contact Reverse Test” above.

Repeat this process as needed until the door passes

the Contact Reverse Test. For further help, refer to

the “Maintenance and Adjustment” section/Regular

Maintenance.

PROGRAMMING FORCE AND CONTACT REVERSE

+ 22 hidden pages