GE GLD6500, GHDA650, GLD6200, GLD4100, GLD5500 User Manual

...
0 (0)
GE GLD6500, GHDA650, GLD6200, GLD4100, GLD5500 User Manual

Dishwashers

ge.com

Safety Instructions . . . . . . . 2, 3

Operating Instructions

Care and Cleaning . . . . . . . . . 12

Control Panel and Settings . . 4–7

Loading Place Settings . . . . . . 11

Loading the Racks . . . . . . . . . 10

Optional Accessories . . . . . . . .11

Using the Dishwasher . . . . . .8, 9

Troubleshooting Tips . . . 13, 14

Write the model and serial numbers here:

Model # __________________

Serial # __________________

You can find them on the tub wall just inside the door.

Owner’s Manual

EDW5000 Series

EDW6000 Series

GHDA450 Series

GHDA650 Series

GLD4100 Series

GLD4200 Series

GLD4300 Series

GLD5500 Series

GLD5800 Series

GLD6200 Series

GLD6300 Series

GLD6500 Series

Consumer Support

Consumer Support . . .Back Cover

Warranty . . . . . . . . . . . . . . . . . 15

165D4700P311 49-5987 05-05 JR

Safety Instructions

Operating Instructions

Troubleshooting Tips

Consumer Support

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or death.

WATER HEATER SAFETY

Under certain conditions hydrogen gas may be produced in a water heater that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE.

If the hot water has not been used for two weeks or more, prevent the possibility of damage or injury by turning on all hot water faucets and allow them to run for several minutes. Do this before using any electrical appliance which is connected to the hot water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance during this process.

Use this appliance only for its intended purpose as described in this Owner’s Manual.

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed and located in accordance with the Installation Instructions before it is used. If you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by visiting our Website at GEAppliances.com.

Connect to a grounded metal, permanent wiring system; or run an equipmentgrounding conductor with the circuit conductors and connect to the equipmentgrounding terminal or lead of the appliance.

Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded.

Use supply conductors rated at least 75°C (167°F).

Dispose of discarded appliances and shipping or packing material properly.

Do not attempt to repair or replace any part of your dishwasher unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.

To minimize the possibility of electric shock, disconnect this appliance from the power supply before attempting any maintenance. NOTE: Turning the dishwasher off does not disconnect the appliance from the power supply. We recommend having a qualified technician service your appliance.

WARNING!

DO NOT…

Do not tamper with controls.

Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.

Do not discard a dishwasher without first removing the door or removing the door latch.

Do not store or use combustible materials, gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

2

Do not allow children to play around dishwasher when opening or closing door due to the possibility of small fingers being pinched in door.

Do not allow children to play with, on or inside this appliance or any discarded appliance.

ge.com

WARNING! RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE DISHWASHER

Junked or abandoned dishwashers are dangerous…even if they will sit for “just a few days.” If you are getting rid of your old dishwasher, please follow the instructions below to help prevent accidents.

Before You Throw Away Your Old Dishwasher:

Take off the door of the washing compartment or remove the door latch

keeper (as shown).

Door latch keeper

WHEN USING YOUR DISHWASHER

CAUTION: Contents washed in Anti-Bacteria cycle may be hot to the touch. Use care before unloading.

Use only powder, tabs, liquid detergents or rinse agents recommended for use in a dishwasher and keep them out of the

reach of children. Cascade® and Electrasol® Automatic Dishwashing Detergents, and

Jet-Dry® and Cascade Crystal Clear® rinse agents have been approved for use in all GE dishwashers.

Using a detergent that is not specifically designed for dishwashers will cause the dishwasher to fill with suds.

Locate sharp items so that they are not likely to damage the door seal.

Load sharp knives with the handles up to reduce the risk of cut-type injuries.

Do not wash plastic items unless marked dishwasher safe or the equivalent. For

plastic items not so marked, check the manufacturer’s recommendations.

Non-Dishware Items: Do not wash items such as electronic air cleaner filters, furnace filters and paint brushes in your dishwasher.

Damage to dishwasher and discoloration or staining of dishwasher may result.

Do not touch the heating element during or immediately after use.

Do not operate your dishwasher unless all enclosure panels are properly in place.

Close supervision is necessary if this appliance is used by or near children.

Load light, plastic items so they will not become dislodged and drop to the bottom of the dishwasher—they might come into contact with the heating element and be damaged.

If your dishwasher is connected to a wall switch, insure that the switch is on prior

to use.

If you choose to turn the switch off

between wash cycles, allow 5–10 seconds after turning the switch on before touching the START/RESET pad to allow the control to boot.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

3

Instructions Safety

Instructions Operating

Tips Troubleshooting

Support Consumer

About the dishwasher control panel. (For models with sensor: EDW6000 Series,

GHDA650 Series, GLD6200 Series, GLD6300 Series, and GLD6500 Series)

SafetyInstructions

You can locate your model number on the tub wall just inside the door. Throughout this manual, features and appearance

may vary from your model.

 

 

 

 

1

 

 

 

 

 

 

 

3

5

4

2

Control Settings

Instructions

 

1

 

Status Indicator Lights

 

 

 

The Status display tells you what’s happening while the dishwasher is in operation and may flash, indicating a

 

 

 

 

 

 

 

 

malfunction (see page 8). The lights will come ON indicating the sequence of operation the dishwasher is in.

 

 

 

 

 

 

 

 

 

SENSING Displayed while the sensor is measuring the amount of soil and temperature of water.

 

 

 

 

(on some models) The dishwasher will adjust the selected cycle to achieve optimal performance.

Operating

 

 

 

WASHING Displayed during prewash and main wash periods.

 

 

 

DRYING Displayed during HEATED DRY.

 

 

 

 

(on some models)

 

 

 

 

 

RINSING Displayed during rinse periods.

 

 

 

 

(on some models)

 

 

 

 

 

(on some models)

 

 

 

 

 

 

 

 

 

 

SANITIZED Displayed when cycle has met sanitization conditions. Light remains ON until door is opened.

 

 

 

 

CLEAN Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are clean until the door is

 

 

 

 

relatched or until another cycle is selected.

 

 

 

 

Time Remaining Display (on some models)

Tips

2

 

 

 

 

During operation, the display shows the minutes remaining until the cycle is complete. The display may adjust

 

 

 

 

Troubleshooting

 

 

 

the remaining time while the sensing light is on. The time displayed at the start of each cycle may change from

 

 

 

ANTI-BACTERIA

Heavy 8.5 gal., 84 min.

 

 

 

 

the factory setting as the unit customizes itself to home use. During a delay start, the display will show hours of

 

 

 

 

time remaining until the cycle starts.

 

 

3

 

Cycles

 

 

 

 

 

The light above the selected pad will be ON to indicate which cycle has been selected.

 

 

 

 

This dishwasher is equipped with a dirt and temperature sensor. Cycle length and time will vary depending on the soil

 

 

 

 

level and temperature.

 

 

 

 

 

 

 

 

 

 

or SANI WASH

Medium 7.3 gal., 78 min.

 

 

 

 

 

Light 6.1 gal., 75 min.

 

 

 

 

 

This cycle raises the water temperature in the final rinse to sanitize your dishware. The cycle length will vary

 

 

 

 

 

depending on the temperature of your inlet water.

 

 

 

 

 

NOTE: The Anti-Bacteria cycle is monitored for sanitization requirements. If the cycle is interrupted during or

 

 

 

 

 

after the main wash portion or if the incoming water temperature is so low that adequate water heating cannot

Support

 

 

 

 

be achieved, the sanitizing conditions may not be met. In these cases, the sanitized light will not illuminate at

 

 

 

 

the end of the cycle.

 

 

 

 

 

 

 

 

 

 

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

 

 

 

 

 

 

Consumer

 

 

 

POTS

Heavy 10.9 gal., 102 min.

 

 

 

& PANS

Medium 8.5 gal., 78 min.

 

 

 

 

 

 

 

 

 

Light 7.3 gal., 73 min.

 

 

 

 

 

This cycle is meant for heavily soiled dishes or cookware with dried-on or baked-on soils.

 

 

 

 

 

Everyday dishes are safe to be used in this cycle.

 

 

 

 

NORMAL WASH

Heavy 8.5 gal., 65 min.

 

 

 

 

 

Medium 7.3 gal., 60 min.

 

4

 

 

 

Light 4.9 gal., 49 min.

 

 

 

 

This cycle is for medium/heavily soiled dishes and glassware.

 

 

 

 

 

ge.com

 

 

SPEED CYCLE

7.3 gal., 35 min.

 

 

or

This cycle is for everyday dishes and glassware.

 

 

SPEED WASH

 

 

 

(on some models)

 

 

 

 

 

 

 

CHINA CRYSTAL

7.3 gal., 48 min.

 

 

(on some models)

This cycle is for lightly soiled china and crystal.

 

 

 

 

 

 

RINSE ONLY

2.5 gal., 12 min.

 

 

 

For rinsing partial loads that will be washed later. Do not use detergent with this cycle.

 

 

NOTE: Only the Anti-Bacteria cycle has been designed to meet the requirements of Section 6,

 

 

NSF 184 for soil removal and sanitization efficacy.

 

 

Options

 

4

 

 

 

 

The light above the selected pad will be ON to indicate which option has been selected.

 

 

 

 

PRE SCRUB

For use with heavily soiled and/or dried-on, baked-on soils. This option MUST be selected PRIOR to starting the

 

 

(on some models)

cycle. This option adds 16 minutes to the cycle time. NOTE: Cannot be selected with RINSE ONLY cycle.

 

 

 

 

 

 

HEATED DRY

Shuts off the drying heat option. Dishes air dry naturally and energy is saved. For faster air dry, you can prop

 

 

Light OFF

the door open after the CLEAN light illuminates.

 

 

 

 

 

 

HEATED DRY

Turns the heater on for fast drying. This will extend the total run time by 8 minutes for the SPEED

 

 

Light ON

CYCLE, 38 minutes for NORMAL and POTS/PANS, and 30 minutes for all other cycles. NOTE: Cannot be

 

 

 

selected with RINSE ONLY cycle.

 

 

 

 

 

 

LOCK

You can lock the controls to prevent any selections from being made. Or you can lock the controls after you have

 

 

 

started a cycle.

 

 

 

Children cannot accidentally start dishwasher by touching pads with this option selected.

 

 

 

To LOCK the dishwasher control, touch and hold the HEATED DRY pad for 3 seconds. The light below the

 

 

 

HEATED DRY pad will turn on. To UNLOCK the dishwasher control, touch and hold the HEATED DRY pad for

 

 

 

3 seconds. The LOCK light will turn off.

 

 

 

 

 

 

ADDED

When selected, the cycle will run longer with the heating element on to improve both wash and dry performance.

 

 

HEAT

NOTE: Cannot be selected with RINSE ONLY cycle.

 

 

 

 

 

 

DELAY HOURS

You can delay the start of a wash cycle for up to 9 hours. Touch the DELAY HOURS pad to choose the number of

 

 

 

hours you want to delay the start of the cycle; then touch START/RESET one time. The dishwasher will count

 

 

 

down and start automatically at the correct time. Touching START/RESET a second time will cancel the

 

 

 

DELAY START selection.

 

 

 

 

 

 

RESET

To change a cycle after washing starts, touch the START/RESET pad to cancel the cycle. The START/RESET light

 

 

 

will flash while the water is pumped out if needed. This takes approximately 90 seconds. When the light stops

 

 

 

flashing, the dishwasher can be reprogrammed and restarted.

 

 

Start

 

5

 

 

 

 

Close and latch the dishwasher door and select the cycle and desired enhancements. Touch the START/RESET pad

 

 

once to begin the cycle. Water begins to fill the dishwasher, and approximately 60 seconds later the wash action begins. Touching the START/RESET pad a second time will cancel the cycle and cause the water to drain out. This will take approximately 2 minutes.

NOTE: The dishwasher remembers your last cycle so you don’t have to reprogram each time. When the dishwasher door is fully closed, the control panel lights will display the last settings you selected.

If you don’t want to change any of the settings, simply touch the START/RESET pad once to begin the cycle.

If the door is closed, the indicator lights will turn off if the START/RESET pad is not pressed within two minutes. To activate the display, open and close the door or touch any pad.

Also, if a power failure occurs, NORMAL and HEATED DRY will automatically be programmed.

5

Instructions Safety

Instructions Operating

Tips Troubleshooting

Support Consumer

Loading...
+ 11 hidden pages