Air Conditioners
Room
ge.com
. . . . . . . . .Safety Instructions |
.2, 3 |
Owner’s Manual and |
|
Operating Instructions |
|
Installation Instructions |
|
|
|
||
Controls—Control Knobs . . . . |
.6, 7 |
AST05 |
|
Controls—Touch Pads . . . . . . |
.4, 5 |
ASW05 |
|
Care and Cleaning |
|
ASH06 |
|
|
ASW06 |
||
Air Filter |
8 |
||
ASH08 |
|||
Batteries . . . . . . . . . . . . . . . . . . . |
. .8 |
||
Grille and Case . . . . . . . . . . . . . |
. .8 |
ASW08 |
|
Outdoor Coils . . . . . . . . . . . . . . |
. .8 |
|
Installation Instructions . . . .9–12
Troubleshooting Tips . . . . . . . .13
Normal Operating Sounds . . . . .13
Consumer Support . . . . . . . . . . .16
Warranty . . . . . . . . . . . . . . . . . . . .15
Write the model and serial numbers here:
Model # ______________________
Serial # ______________________
Find these numbers on a label on the side of the air conditioner.
DB98-26673A 49-7551 10-06 JR
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock or personal injury.
SAFETY PRECAUTIONS
■Use this appliance only for its intended purpose as described in this Owner’s Manual.
■This air conditioner must be properly installed in accordance with the Installation Instructions before it is used.
■Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight out from the receptacle.
■Replace immediately all electric service cords that have become frayed or otherwise damaged. A damaged power supply cord must be replaced with a new power supply cord obtained from the manufacturer and not repaired. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.
■Turn the unit OFF and unplug your air conditioner before cleaning.
■GE does not support any servicing of the air conditioner. We strongly recommend that you do not attempt to service the air conditioner yourself.
■For your safety…do not store or use combustible materials, gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.
■All air conditioners contain refrigerants, which under federal law must be removed prior to product disposal. If you are getting rid of an old product with refrigerants, check with the company handling disposal about what to do.
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.
Power cord includes a current interrupter device. A test and reset button is provided on the plug case. The device should be tested on a periodic basis by first pressing the TEST button and then the RESET button. If the TEST button does not trip or if the RESET button will not stay engaged, discontinue use of the air conditioner and contact a qualified
service technician.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Where a 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
The air conditioner should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.
This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.
See the Installation Instructions, Electrical Requirements section for specific electrical connection requirements.
2
ge.com
WARNING!
USE OF EXTENSION CORDS—115-Volt models only
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed, 14 gauge, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the
cord be 15 amperes (minimum) and 125 volts.
CAUTION:
DO NOT use an extension cord with any of the 230/208 volt models.
USE OF ADAPTER PLUGS—115-Volt models only
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.
However, if you must use an adapter, where local codes permit, a temporary connection may be made to a properly grounded 2-prong wall outlet by use of a UL-listed adapter available at most local hardware stores.
The larger slot in the adapter must be aligned with the larger slot in the wall outlet to provide proper polarity in the connection of the power cord.
When disconnecting the power cord from the adapter, always hold the adapter in place with one hand while pulling the power cord plug with the other hand. If this is not done, the adapter ground terminal is very likely to break with repeated use.
If the adapter ground terminal breaks, DO NOT USE the air conditioner until a proper ground has been established.
Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the cover screw is metal, and not insulated, and the wall outlet is grounded through the house wiring. You should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
3
Support Consumer Tips Troubleshooting Instructions Installation Instructions Operating Instructions Safety
Consumer Support Troubleshooting Tips Installation Instructions Operating Instructions Safety Instructions
About the controls on the air conditioner—models with touch pads.
Features and appearance will vary.
COOL On |
|
FAN On |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ENERGY |
TIMER On |
|
SAVER On |
||
|
||
SLEEP On |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Air Conditioner Controls |
Remote Control |
On/Off
Turns air conditioner on and off.
Display
Displays the set temperature or time remaining on timer.
Mode
Use to set the air conditioner to Cool or Fan mode.
Increase ▲ /Decrease ▼ Pads
Use to set temperature when in Cool mode.
Fan
Use to set the fan speed at Low, Med or High.
Circulaire (on some models)
Turn on to provide continuous side-to-side air circulation.
For fixed side-to-side air direction, turn On until the desired air direction is obtained, then turn it Off.
Energy Saver–Controls the fan.
On—The fan and compressor cycle on and off. This results in wider variations of room temperature and humidity. Normally used when the room is unoccupied. Note: The fan will continue to run for a short time after the compressor cycles off.
Off—The fan runs all the time, while the compressor cycles on and off.
This switch must be set at Off in order to use the fan settings (on the mode control).
Timer
On—When the air conditioner is off, it can be set to automatically turn on in 1 to 24 hours at its previous setting. Each touch will set the time in hours.
Off—When the air conditioner is on, it can be set to automatically turn off in 1 to 24 hours. Each touch will set the time in hours.
To cancel the timer, press the Timer pad until the display time disappears.
Sleep (on some models)
Press to set the air conditioner to run for 8 hours before it automatically shuts off.
One hour after the sleep timer is set, the set temperature will automatically increase 2°F.
To cancel the sleep mode, press the Sleep pad a second time.
Note: The sleep timer will be cancelled if the
Timer, Energy Saver or Mode pad is pressed.
Remote Control Signal Receiver
Remote Control
■To ensure proper operation, aim the remote control at the signal receiver on the air conditioner.
4■ The remote control signal has a range of up to 21 feet.
■Make sure nothing is between the air conditioner and the remote control that could block the signal.
■Make sure batteries are fresh and installed correctly—see the Care and Cleaning section.
ge.com
Additional controls and important information.
Do Not Operate in Freezing Outdoor Conditions
This cool-only air conditioner was not designed for freezing outdoor conditions. It must not be used in freezing outdoor conditions.
When the air conditioner is turned on, it will automatically start in the setting last used.
Power Outage Recovery Feature
In the case of a power outage or interruption, the |
Sleep features will reset to the original setting. |
unit will automatically re-start in the settings last |
You may need to set a new time if desired. |
used after the power is restored. The Timer and |
|
|
|
Cool Mode
Use the Cool mode with High (3), Med (2) or
Low (1) fan for cooling. Use the Increase ▲ / Decrease ▼ pads to set the desired temperature between 64°F and 86°F in 1°F increments.
A thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become warmer.
NOTE: If the air conditioner is off and is then turned on while set to Cool, it will take approximately 3 minutes for the compressor to start and cooling to begin.
Cooling Descriptions
For Normal Cooling—Select the Cool mode and High (3) or Med (2) fan with a middle set temperature.
For Maximum Cooling—Select the Cool mode and High (3) fan with a lower set temperature.
For Quieter & Nighttime Cooling—Select the
Cool mode and Low (1) fan with a middle set temperature.
NOTE: If you switch from a Cool setting to Off or to
a fan setting, wait at least 3 minutes before switching back to a Cool setting.
Fan Mode
Use the Fan at High (3), Med (2) or Low (1) to provide |
Since fan only settings do not provide cooling, |
|||||
air circulation and filtering without cooling. |
a temperature setting will not be displayed. |
|
||||
|
|
|
|
|
|
|
Vent Control (on some models) |
|
|
|
|
|
|
The vent control is located on the inside of the |
|
|
|
|
|
|
air louvers in the lower right corner. |
|
|
|
|
|
|
|
|
|
|
|
|
|
When set at CLOSE, only the air inside the room |
|
|
|
|
|
|
|
|
|
|
|
|
|
will be circulated and conditioned. When set at |
|
|
|
|
|
|
|
|
|
|
|
|
|
OPEN, some inside air is exhausted outside. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
the vent, push the lever to |
. |
||
|
To close it, push it to the left. |
|
||||
|
|
|
|
|
|
|
Air Direction—Up and Down (on some models)
Fingertip pressure on the horizontal louvers adjusts |
|
the air direction up or down. |
OR |
|
Air Direction—Side-to-Side (on some models)
The side-to-side air direction is adjusted by the louver levers.
5
Support Consumer Tips Troubleshooting Instructions Installation Instructions Operating Instructions Safety
Consumer Support Troubleshooting Tips Installation Instructions Operating Instructions Safety Instructions
About the controls on the air conditioner—models with control knob(s).
Features and appearance may vary.
Controls (on models so equipped)
ON/OFF Switch
Turns air conditioner on and off.
NOTE: If the air conditioner is off and is then turned on while set in a Cool mode, it will take approximately 3 minutes for the compressor to start and cooling to begin.
Fan Switch (on some models)
Use to set the fan speed to LO or HI.
Mode/Temp Control
Use to set the air conditioner to the Fan Only or a Cool mode.
Fan Only Mode
Use Fan Only at HI or LO Fan to provide air circulation and filtering without cooling.
Cool Mode
Use a Cool setting with HI or LO Fan for cooling. Turn the knob clockwise, toward the larger blue area, for the indoor area to become cooler. Turn the knob counterclockwise, toward the smaller blue
Controls (on models so equipped)
area, for the indoor air to become warmer.
The Mode/Temp control is used to maintain the room temperature. When set in a Cool mode, the compressor will cycle on and off to keep the room at the same level of comfort.
Cooling Descriptions
For Normal Cooling—Select a Cool mode with the Mode/Temp knob set at the midpoint.
For Maximum Cooling—Select a Cool mode with the Mode/Temp knob set toward the larger blue area.
For Quieter & Nighttime Cooling—Select a Cool mode with the Mode/Temp knob set toward the smaller blue area.
NOTE: If you move the Mode/Temp control knob from a Cool setting to the Fan On setting, wait at least 3 minutes before switching back to a Cool setting.
Mode Control
Hi Cool, Med Cool and Low Cool provide cooling with different fan speeds.
Low Fan or Hi Fan provides air circulation and filtering without cooling.
Thermostat Control
The thermostat control is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the same level of comfort. When you turn the knob to a higher number, the indoor air will become cooler. Turn
6 the knob to a lower number and the indoor air will become warmer.
NOTE: If you move the switch from a cool setting to OFF or
to a fan setting, wait at least 3 minutes before switching back to a cool setting.
Cooling Descriptions
For Normal Cooling–Select Hi Cool or Med Cool with the thermostat control at midpoint.
For Maximum Cooling–Select Hi Cool with the thermostat control at the highest number available on your knob.
For Quieter & Nighttime Cooling–Select Low Cool with the thermostat control at midpoint.
ge.com
Additional controls and important information.
Do Not Operate in Freezing Outdoor Conditions
This cool-only air conditioner was not designed for freezing outdoor conditions. It must not be used in freezing outdoor conditions.
Vent Control (on some models)
The vent control is located on the inside of the air louvers in the lower right corner.
When set at CLOSE, only the air inside the room will be circulated and conditioned. When set at OPEN, some inside air is exhausted outside.
To open the vent, push the lever to the right.
To close it, push it to the left.
Air Direction—Side-to-Side
The side-to-side air direction is adjusted by the louver levers.
Air Direction—Up and Down (on some models)
Fingertip pressure on the horizontal louvers adjusts the air direction up or down.
OR
7
Support Consumer Tips Troubleshooting Instructions Installation Instructions Operating Instructions Safety
Consumer Support Troubleshooting Tips Installation Instructions Operating Instructions Safety Instructions
Care and cleaning of the air conditioner.
How to Insert the Batteries on the Remote Control (on some models)
1
2
3
Remove the battery cover by sliding it according to the arrow direction.
Insert new batteries making sure that the (+) and (–) of battery are installed correctly.
Reattach the cover by sliding it back into position.
NOTES:
■Use 2 “AAA” (1.5 volt) batteries. Do not use rechargeable batteries.
■Remove the batteries from the remote control if the system is not going to be used for a long time.
Turn the air conditioner off and remove the |
To clean, use water and a mild detergent. |
plug from the wall outlet before cleaning. |
Do not use bleach or abrasives. |
The coils on the outdoor side of the air conditioner should be checked regularly. If they are clogged with dirt or soot, they may be professionally cleaned.
The air filter behind the front grille should be |
To remove: |
checked and cleaned at least every 30 days or |
|
more often if necessary. |
|
Clean the filter with warm, soapy water. Rinse and |
|
let the filter dry before replacing it. |
|
CAUTION: DO NOT operate the air conditioner without a filter because dirt and lint will clog it and reduce performance.
Grab the tabs on the filter and pull it up and out.
8
Installation |
Air Conditioner |
Instructions |
|
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT — Save these
instructions for local inspector’s use.
• IMPORTANT — Observe all governing codes and ordinances.
•Note to Installer – Be sure to leave these instructions with the Consumer.
•Note to Consumer – Keep these instructions for future reference.
•Skill level – Installation of this appliance requires basic mechanical skills.
•Completion time – Approximately 1 hour
•We recommend that two people install this product.
•Proper installation is the responsibility of the installer.
•Product failure due to improper installation is not covered under the Warranty.
•You MUST use all supplied parts and use proper installation procedures as described in these instructions when installing this air conditioner.
ELECTRICAL REQUIREMENTS
Some models require a 115/120-volt a.c., 60 Hz grounded outlet protected with a
15-amp time delay fuse or circuit breaker.
The 3-prong grounding plug minimizes the possibility of electric shock hazard. If the wall outlet you plan to use is only a 2-prong outlet, it is your responsibility to have it replaced with a properly grounded 3-prong wall outlet.
Some models require 230/208-volt a.c., protected with a time delay fuse or circuit breaker. These models should be installed on their own single branch circuit for best performance and to prevent overloading house or apartment wiring circuits, which could cause a possible fire hazard from overheating wires.
9
CAUTION:
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
Do not change the plug on the power cord of this air conditioner.
Aluminum house wiring may present special problems—consult a qualified electrician.
TOOLS YOU WILL NEED
Phillips head screwdriver
Pencil |
|
Ruler or tape measure |
|
|
|
Level |
|
Scissors or knife |
|
|
|
|
|
|
Power cord includes a current interrupter device. A test and reset button is provided on the plug case. The device should be tested on a periodic basis by first pressing the TEST button and then the RESET button. If the TEST button does not trip or if the RESET button will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician.
Installation Instructions
PARTS INCLUDED |
|
|
(appearance may vary) |
|
Window |
|
|
sash seal |
Top mounting rail |
|
|
|
Foam top |
|
|
window gasket |
|
|
Top mounting rail |
|
|
seal strip |
|
|
Left |
|
|
accordion |
|
Air |
panel |
Right |
|
||
|
accordion |
|
conditioner |
|
|
|
panel |
|
|
|
|
Type A (9 or 10) |
Type B (7) |
Security bracket (3) |
1/2″ screws |
3/4″ screws |
|
|
10 |
|