USER MANUAL FOR
DIGITAL CINEMA SERVER
SX-2000A SERIES WITH INTEGRATED MEDIA BLOCK/
SX-2001A SERIES
(SHORT FORM VERSION)
SMS version 8.01
September 6, 2012
SX-2000A Digital Cinema Server with
Integrated Media Block
SX-2001A Digital Cinema Server
The stunning solution for both 2K and 4K digital cinema
GDC Technology’s fifth generation digital cinema playback server, SX-2000A Digital
Cinema Server with Integrated Media Block/SX-2001A Digital Cinema Server,
designed to fully comply with DCI specifications and FIPS-140 security
requirements. The SX-2000A/SX-2001A can support both 2K and
4K resolutions that is future-proof based on Texas Instrument’s
Enhanced DLP Cinema
®
technology, retaining all of
the attractive SA-2100A’s features.
TABLE OF CONTENTS
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 4 -
September 6, 2012
TABLE OF CONTENTS
1. INTRODUCTION ............................................................................................... 8
1.1. About This Manual ..................................................................................... 8
1.2. Safety Instructions ..................................................................................... 9
1.2.1. General Safety Instructions ..................................................................................................... 9
1.2.2. Electrical Safety ....................................................................................................................... 9
2. SMS .............................................................................................................. 10
2.1. About the SMS Interface .......................................................................... 10
2.2. Accessing the SMS Interface ................................................................... 10
2.3. Understanding the SMS Interface ........................................................... 11
2.3.1. Main Menu ............................................................................................................................ 11
2.3.2. Playlist Menu ................................ ......................................................................................... 13
2.3.3. Scheduler Menu .................................................................................................................... 17
2.4. Show Playlist ............................................................................................ 18
2.4.1. Create a Show Playlist .......................................................................................................... 18
2.4.2. Editing Cues .......................................................................................................................... 19
2.4.3. Saving the Playlist ................................................................................................................. 24
2.5. Show Schedule ......................................................................................... 25
2.5.1. Schedule a Show .................................................................................................................. 25
3. CONTROL PANEL ......................................................................................... 31
3.1. About Control Panel ................................................................................. 31
3.2. Control Panel Menu .................................................................................. 32
3.3. Manual Automation Execution ................................................................ 33
4. CONTENT MANAGER ................................................................................... 35
4.1. About the Content Manager ..................................................................... 35
4.1.1. Introduction ........................................................................................................................... 35
4.1.2. Accessing the Content Manager ............................................................................................ 35
4.2. Content Management ............................................................................... 36
4.2.1. Ingesting Content .................................................................................................................. 36
TABLE OF CONTENTS
September 6, 2012
- 5 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
4.2.2. Ingesting Content from USB Disk .......................................................................................... 38
4.2.3. Ingesting from DVD-ROM Drive ............................................................................................ 40
4.2.4. Ingesting from CRU DataPort ................................................................................................ 41
4.2.5. Ingesting KDMs ..................................................................................................................... 43
4.2.6. Monitor Ingest Progress ........................................................................................................ 44
4.2.7. Cancelling Ingest ................................................................................................................... 45
4.2.8. Deleting Content .................................................................................................................... 46
4.2.9. Checking Content Integrity .................................................................................................... 47
4.3. KDM Management .................................................................................... 52
4.3.1. Manage KDM ................................................................................................ ........................ 52
5. SERVER OPERATION NOTES ...................................................................... 53
5.1. Important Notes ........................................................................................ 53
5.2. Power Up & Shutdown ............................................................................. 53
5.2.1. Power Up .............................................................................................................................. 53
5.2.2. Shutdown .............................................................................................................................. 53
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 6 -
September 6, 2012
Thank you for purchasing a GDC Digital Cinema Server SX-2000A Series with
Integrated Media Block/SX-2001A Series from GDC Technology Limited.
To ensure proper operation and to maximize the server’s value, please review this short form User Manual.
It will guide you through all the features and benefits of the new SX-2000A with Integrated Media Block/SX2001A. The full version of the user manual is available on the accompanying CD.
COPYRIGHT NOTICE
Copyright © 2012 by GDC Technology Limited
All rights reserved. No part of this manual may be copied or distributed, transmitted, transcribed, stored in a retrieval
system, or translated into any human or computer language, in a form or by any means, electronic, mechanical, photocopying,
recording, magnetic, optical, manual or otherwise, or disclosed to third parties without prior written permission of
GDC Technology Limited.
MANUAL DISCLAIMER
This manual is made with SMS version 8.01 and there might be slight differences depending on the software version the
server is running. The contents, features and specifications stated in this manual are subject to change without notice due to
continuous product development and improvements. In no other event shall GDC Technology Limited be liable for any loss of
profit or any other commercial damages, including but not limited to special, consequential, or other damages.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
September 6, 2012
- 7 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
CONTACTS AND OFFICES
Website: www.gdc-tech.com Email: info@gdc-tech.com
24/7 Engineering Support Hotline:
America
+1 877 743 2872 (Toll Free)
South East Asia
+65 6100 4328
Europe
+34 616 257 894
Australia/ New Zealand
+65 6100 4328
China
+86 400 886 0966 (Toll Free)
North Asia
+852 3520 0920
USA USA (Sterling, VA) Spain (Barcelona) Hong Kong
(Los Angeles, CA)
GDC Technology (USA) GDC Technology of GDC Digital Cinema GDC Technology Limited
LLC America LLC Technology Europe, SL
1016 West Magnolia 21155 Whitfield Place Av. Diagonal, 177, ‘Unit 1-7, 20th Floor,
Boulevard, Burbank, Suite 207, Sterling, 9th Floor, 08018 Barcelona, Kodak House II,
CA 91506, USA VA 20165, USA ‘ Spain ‘39 Healthy Street East
North Point, Hong Kong
Tel: +1 818 972 4370/ Tel: +1 877 337 0868 Tel: +34 93 238 14 10 Tel: +852 2523 6851
+ 1 877 743 2872 (Toll Free)
(Toll Free)
Fax: +1 877 643 2872 Fax: +1 571 313 0468 Fax: +34 93 309 31 88 Fax: +852 2579 1131
Japan (Tokyo) Singapore China (Shenzhen) China (Beijing)
GDC Digital Cinema GDC Technology Pte GDC Technology (Shenzhen) GDC Technology (Beijing)
Network GG. Limited Limited Limited
7F Nishino Kinryo Bldg, 6 Changi South Street 2 5th floor GDC Building, Rm 609-618, Office Building
4-9-4, Hatchobori, Chuo-ku, Fedex Building, Level 7 No.9 Hi-tech Middle 3 Road, 20# Xinde Street,
Tokyo 104-0032, Japan Singapore 486349 Science & Technology Park, Xicheng District,
Nanshan District, Shenzhen, Beijing, P.R. China 100088
P.R. China 518057
Tel: +81 3 3523 2650 Tel: +65 6222 1082 Tel: +86 755 8608 6000 Tel: +86 10 6205 7040
Fax: +81 3 3523 2651 Fax: +65 6222 1089 Fax: +86 755 8608 8098 Fax: +86 10 6205 7054
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 8 -
September 6, 2012
1. INTRODUCTION
1. INTRODUCTION
1.1. About This Manual
This user manual provides instructions on how to use and manage the GDC Digital
Cinema Server SX-2000A Series with Integrated Media Block (“IMB”)/SX-2001A Series.
The user interface of the server consists of a few key components described in the
diagram below [Figure 1]. The manual has sections on each of these components
describing how it can be used to operate the server.
Control Panel
The Control Panel UI enables
access to all the other menus
used to configure and operate
the server.
SMS
Main interface used for
playback control and to
create and schedule
playlists.
Content Manager
Used to download content
from a disk or source on
the network, delete content
from the server, verify the file
integrity of the content, and to
download KDM’s required for
content playback.
Admin Panel
Provides an array of easy to
access menu pages that
simplify the configuration
and maintenance of the server.
Figure 1 Server UI components.
September 6, 2012
- 9 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
1. INTRODUCTION
1.2. Safety Instructions
1.2.1. General Safety Instructions
• The server is intended for installation in a restricted access location.
• The operation environment required for the server should be 0ºC - 40ºC (32ºF - 104ºF).
• For PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the equipment and shall be
easily accessible.
• Before operating your server, please read this manual thoroughly, and retain it for future reference.
• Installation and preliminary adjustments should be performed by qualified GDC Technology personnel.
All warnings on the server and in the documentation manual should be adhered to.
• All instructions for operating and maintaining the server must be followed closely.
1.2.2. Electrical Safety
Safety Warning
• Do not expose the server to rain or moisture, to prevent fire or electrical shock hazard.
• Use a dry cloth when cleaning the server.
• Do not block any ventilation openings.
• Do not install near any heat sources (e.g. radiators, stove or other apparatus that produce heat).
• Refrain from removing the top cover of the server, to prevent electric shock. Consult Tech Support for servicing
or maintaining the server.
• You are cautioned that any change or modification not expressly approved in this manual or approved in writing by
an authorized representative of GDC Technology could void your warranty and/or authority to operate this server.
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 10 -
September 6, 2012
2. SMS
2. SMS
2.1. About the SMS Interface
The SMS interface is used for playback control, creating and editing playlists, scheduling and also provides access
to advanced configuration options.
2.2. Accessing the SMS Interface
Figure 2 SMS interface.
1
Switch on the server by pressing the ON / OFF button on the front panel of the server, and
allow it to boot directly to the SMS interface as seen in Figure 2.
September 6, 2012
- 11 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
2. SMS
2.3. Understanding the SMS Interface
2.3.1. Main Menu
Figure 3 SMS main menu.
1
[►]
Play button. The [►] button starts playback when pressed, and is disabled
when the system is in paused mode.
2
[ || ]
Pause button. The [ ] button is enabled when the system is in playing or
pause mode. To resume from pause simply hit the Pause button again.
3
[■]
Stop button. The [■] button is enabled when the system is in playing mode,
and stops playback when pressed.
4
[
]
Playlist button. Press to open the Playlist menu to create a playlist.
For more information about the Playlist menu, please refer to Section 2.3.2.
Playlist Menu further below
.
1
5 6 7
10
2 3 8
9
4 1213
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 12 -
September 6, 2012
2. SMS
5
[Slider Bar]
It will start advancing when [►] is pressed to start a playback. One clip will
take one complete cycle from the left to the right. The Slider Bar always
returns to the starting point (extreme left) after a clip is finished. When [■]
is pressed, the Slider Bar will stop and return to its starting point.
When playback is paused, the Slider Bar can be moved. The Slider Bar
can be moved to the left (for rewinding) or to the right (for forwarding).
6
[
|◄
]
[
]
[]
[►
]
Move to the first frame of the clip.
Rewind (move back) by the number of frames of the playback.
Forward (move forward) by the number of frames of the playback.
Move to the last frame of the clip.
7
[Status Display]
Reports the status of the system. The display shows the number of clips in
the active playlist, the name of the active playlist, and the name of the clip
currently being played.
8
[ i ]
INFORMATION button. If [ i ] is pressed when the system is in stopped mode
,
the system will show the serial number and the software version of the
server. A text box will appear beside the Timecode Display (replacing the
navigating buttons [|◄] [] [] [►]) and the text box will show the serial
number and software version of the server.
9
[ ]
SCREEN LOCK button - The SCREEN LOCK function will prevent any
unintentional screen touches or mouse clicks that could disturb a playback.
The screen will be locked when [ ] button is pressed. No access to the
Main Menu (or associated menus) is allowed when the screen is locked.
The User level password or higher is needed to unlock the screen.
If the screen is locked while the system is playing, the name, duration and
the remaining time of the clip will be shown on the screen while the clip is
playing.
10
[Control Panel]
CONTROL PANEL button – For returning to the control panel screen of the
user interface.
11
[Scheduler]
SCHEDULE button – For scheduling the time and date of the playlists to be
shown. The playlist can also be looped for a period of time.
12
[Configuration]
CONFIGURATION button – For changing the general options on the system
(e.g. enable startup/ shutdown password, change access level passwords,
perform software upgrade, etc.).
13
[Shutdown]
SHUTDOWN button. For shutting down the server or restarting the application.
Serial
Number
Software
Version
September 6, 2012
- 13 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
2. SMS
2.3.2. Playlist Menu
Figure 4a Playlist menu.
12
14 6 21 13
15
16
17
18
10
11 9 8
4 7 5
3
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 14 -
September 6, 2012
2. SMS
Figure 4b TimeCode keypad.
1
[Server Content]
The content on the server is listed here. Content is shown in alphabetical
order grouped by [Trailer, Feature, etc]. Available automation cues are
listed under cues
.
2
[Playlist Content]
The contents of the playlist being currently edited are shown here.
3
[Clip
Information]
Displays information about the selected item in Server Content. This
includes the Name, total Duration, Sound (Audio) format, if Encryption is
present, if a Composition Playlist exists, if it has Subtitles, if a current KDM
is on the server, Rating Agency, and Rating Label
.
4
[+]
Adds content to the Playlist by pressing [+] after an item from the Server
Content is selected.
5
[-]
Removes the selected item from the Playlist content.
19
20
September 6, 2012
- 15 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
2. SMS
6
[Loop]
When [Loop] is selected, the contents in the Playlist will run continuously
in a loop when [►] is pressed.
7
[3D Sync]
Synchronizes clips for 3D showing.
8
[Clear]
Removes all clips on the playlist.
9
[Edit Cue]
Go to Edit Cue>TimeCode Keypad (refer to 19 in Figure 4b) > Goto End
(refer to 20 in Figure 4b).This will bring up the cue editing user interface
used to add, remove or edit existing automation cues in the playlists.
10
[
]
Moves the highlighted clip in the Playlist ahead in chronological order
.
Makes sure an item is selected from the Playlist before pressing [
].
When [ ] is pressed, the selected item will move to before the previous
clip.
11
[
]
Moves the highlighted clip in the Playlist down in chronological order
.
Makes sure an item is selected from the Playlist before pressing [
].
When [ ] is pressed, the selected item will move to after the next clip.
12
[Shows]
This displays a list of all the playlists saved on the server. Selecting a
playlist here displays the contents of the playlist for editing. A playlist that
is currently playing may not be edited.
NOTE: Selecting a playlist here does not load it for playback. The “Load
Show to Play” button has to be pressed to load the playlist into the player
for playback.
13
[Load Show To Play]
Loads the selected playlist into the player for playback
.
14
[Save Show]
Saves the playlist currently being edited.
15
[New Show]
Creates a new blank show playlist. A name must be specified for the
playlist.
16
[Delete Show]
Make sure an item is selected in the Shows drop-down menu. When
[Delete Show] is pressed, the system will delete the selected playlist and
remove it from the Shows drop-down menu.
The delete action is irreversible. The system will prompt you to confirm the
delete action before it proceeds to delete the playlist.
17
[Copy Show]
Duplicates currently selected playlist. When [Copy Show] is pressed, a text
entry keypad will appear for you to enter the new name of the duplicate
playlist.
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 16 -
September 6, 2012
2. SMS
Type in the desired name and press [Enter] to complete the action. To
cancel the action and return to the previous screen, press [Cancel]
.
18
[Close]
Exits the Playlist menu and returns to the Main menu.
19
[TimeCode]
Move up and down to choose the expected time code for cue position.
20
[Goto End]
Go to the CPL end time code for cue position.
Cancel
Enter
September 6, 2012
- 17 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
2. SMS
2.3.3. Scheduler Menu
Figure 5 Scheduler menu.
1
[Select Date]
Specifies the date and time of the schedule.
2
[Timeline]
Displays shows
scheduled
on a 24-hour timeline for the date selected in (1).
3
[Selected Schedule
Information]
Displays information such as name, time and duration of the selected
show schedule.
4
[Delete Schedule]
[Previous], [Next]
Deletes the currently selected show schedule.
Navigate show schedules by going forward and backward one at a time.
5
[Add to Schedule]
(a) Select the playlist to be scheduled. The contents of the selected
playlist will be displayed in the “Selected Playlist” window.
(b) Select the time for the scheduled show.
(c) To loop the show until a certain time, check ‘Loop until’ and select
the time.
(d) If the schedule is to be repeated every day or week, check ‘Set
recurrence rules’.
(e) Press the ‘Add’ button. A dialog will pop up for specifying the
recurrence rules if it was checked.
1
2
3
4
5
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 18 -
September 6, 2012
2. SMS
2.4. Show Playlist
2.4.1. Create a Show Playlist
Figure 6 Playlist menu.
1
On the Playlist menu, all compositions stored in the server are listed in the Server Content
column on the left. Server content is shown in alphabetical order grouped by type [Trailer
,
Feature, etc.]. Available automation cues are listed under ‘cues’.
2
Select the composition to add to the playlist and press [ + ]. Repeat the same step to add other
compositions (e.g. trailers or advertisements) to the playlist.
3
Compositions in the playlist are shown in the Playlist column on the right. Use [ ] (move up) and
[
] (move down) to change the order of compositions in the playlist. The order of the
compositions in the playlist may also be changed by dragging their icons in the timeline display
.
4
You can remove compositions from the Playlist column by selecting the clip that you want to
remove and pressing [ - ].
2
4
September 6, 2012
- 19 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
2. SMS
2.4.2. Editing Cues
Figure 7 Playlist menu.
1
To edit a cue of a composition on the playlist, select the desired composition from the Playlist
menu and press Edit Cue. A new window displaying the Edit Cue menu opens as seen in
Figure 8.
1
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 20 -
September 6, 2012
2. SMS
Figure 8 Edit Cue menu.
2
To specify a time code for the activation of the cue, press and a time code entry window
will open. Use the [▲] and [▼] buttons enter the desired time code. Press OK to confirm
your selection.
To specify a frame for the activation of the cue, press the Time button once and it will toggle
to display the Frame button as shown below.
3 4 2 6 5 78
September 6, 2012
- 21 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
2. SMS
Press and a frame number entry window will open. Key in the desired frame number
and
press Enter
.
3
Press Marker to view any markers present in the composition.
If the composition does not contain any markers, a small window pops up to indicate that
there are no markers present.
4
To add an automation cue label, select the desired automation cue label from the dropdown
list as seen below
.
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 22 -
September 6, 2012
2. SMS
5
To add a start cue, tick the Start Cue option and select the desired automation cue label from
the dropdown list as seen below.
To specify the blank time, press and a blank time entry window will open. Key in the
desired blank time and press Enter.
NOTE: A start cue is activated immediately before the composition plays. The blank time
indicates the time interval between the end of the start cue and the start of the composition’s
playback.
September 6, 2012
- 23 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
2. SMS
6
Press Add Cue to add the cue to the composition.
The cue’s details will then be displayed in the cue window as seen below
NOTE: You can select a cue from the cue window at any time to edit its properties.
7
To delete a cue from the composition, select the cue from the cue window and press Delete Cue
.
8
To save the changes and exit, press OK.
To exit without saving any changes, press Cancel
.
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 24 -
September 6, 2012
2. SMS
2.4.3. Saving the Playlist
Figure 9 Saving the playlist.
1
Press Save Show to save the playlist. This ensures any changes to playlist will not be lost.
2
Press Load Show to Play and return to the Main menu.
September 6, 2012
- 25 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
2. SMS
2.5. Show Schedule
2.5.1. Schedule a Show
Figure 10 SMS Interface [Scheduler].
1
On the Main menu, press Scheduler. A new window opens as seen in Figure 11
.
1
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 26 -
September 6, 2012
2. SMS
Figure 11 Scheduler menu.
2
Go to the bottom section named Add to Schedule. At Date / Time, indicate the date and time
to
schedule the show.
(a) The date format is DD/MM/YYYY and the time format is HH:MM:SS. To select the day
,
click on DD and adjust to the required day using [▲] and [▼]. Repeat the same for MM, YYYY,
HH, MM and SS.
(b) At Shows, select the playlist for the show. Press [ ] to view all the playlists already
saved in the server. Select the required playlist.
2
September 6, 2012
- 27 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
2. SMS
(c) The Selected Playlist column on the right displays the clips in each playlist.
(d) If you want the playlist to loop for a period of time, check Loop Until and indicate the date
and time to end the loop.
(e) Press Add after the schedule date/time is fixed and playlist is selected.
(f) If the new show schedule does not conflict with other schedules already saved to the
server, the schedule will be added to the existing list of schedules in the server.
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 28 -
September 6, 2012
2. SMS
Figure 12 Viewing schedule information.
3
4
September 6, 2012
- 29 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
2. SMS
3 Check the Enable Scheduler checkbox to enable scheduled playback
(a) At Select Date, indicate the date of the schedule. You should see a line on the
time-bar at the slot where the show is scheduled.
(b) Click on the line. Information about the show such as name, time and duration will be
displayed in the Selected Schedule Information column beneath the time-bar.
(c) To navigate to the previously scheduled show just before the selected show, press
[Prev].
(d) To navigate to the succeeding show scheduled after the selected show, press [Next]
.
(e) To delete a show schedule from the time-bar, just click on the relevant color bar and
press [Del. Schedule].
4
To replicate the same show schedule on other days, check Set recurrence rules and press Add
.
(a)
(b)
(d)
(e)
(c)
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 30 -
September 6, 2012
2. SMS
Figure 13 Replicating show schedule.
5
A new window opens as seen in Figure 13. Select the required recurrence option. Only
one option can be selected. Upon selection, all effective recurring dates will be listed in the
Schedule recurrence dates column at the bottom.
6
Press Apply recurrence rules to schedule the recurrence dates. If no option is selected, press
Return to the scheduler to return to Scheduler menu. When on Scheduler menu, press Back
to return to the Main menu.
5
6
September 6, 2012
- 31 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
3. CONTROL PANEL
3. CONTROL PANEL
3.1. About Control Panel
The Control Panel UI provides access to all the other menus used to configure and operate
the SX-2000A/SX-2001A server. To get to the Control Panel, press the On/Off button on the
front of the server.
Alternatively, press Control Panel on the Main menu as shown in Figure
14.
Figure 14 Control Panel menu.
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 32 -
September 6, 2012
3. CONTROL PANEL
3.2. Control Panel Menu
Figure 15 Control Panel menu.
1
Switch ON the server and allow it to boot up to prompt directly to the SMS interface.
When
the SMS interface is shown, push the ON/OFF button once or press the Control
Panel button and a new window for the Control Panel menu opens as shown in Figure
15. The Control Panel includes the Extract Logs & configuration buttons, the Automation
button, Admin panel button, Manage Content button, System monitor button, SMS button,
Restart button, Shutdown button and a Refresh status button. System information including
the serial number, OS version, SMS version, network and storage information can also be
seen on the Control Panel UI.
NOTE: The Refresh status button is used to manually refresh the status of the hard disks in
the server. This button should not be pressed during playback to prevent disruption of
playback.
WARNING: Do not press the ON/OFF button for more than 2 seconds when in the
Control Panel menu to prevent accidental shutdown of the system. This may cause a
hard reset and any running applications will be terminated without visual warning.
The SMS software continues to run in the background when using the Control Panel.
This allows access to other server functions when playback is in progress. It is
recommended that these functions be used very sparingly to avoid unnecessary system
load that can potentially affect playback performance.
1
September 6, 2012
- 33 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
3. CONTROL PANEL
3.3. Manual Automation Execution
Figure 16 Accessing Automation.
Figure 17 Executing Automation.
1
2
3
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 34 -
September 6, 2012
3. CONTROL PANEL
1
Automation labels and projector commands can now be executed from an interface on the
Control Panel. Press Automation on the Control Panel to start the manual automation interface
as shown in Figure 16
.
2
A new window opens as seen in Figure 17. Select an automation label to view the actions
associated with the label. Press Execute to execute the automation label.
3
When a projector is configured for automation, projector primitives and macros can be triggered
from this interface as well. Select the projector primitive or macro to be executed, and click the
Send Projector Primitive or Send Projector Macro to send the command to the projector.
September 6, 2012
- 35 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
4. CONTENT MANAGER
4. CONTENT MANAGER
4.1. About the Content Manager
4.1.1. Introduction
The SX-2000/SX-2001Content Manager allows the user to manage the contents of the server to:
4.1.2. Accessing the Content Manager
Figure 18 Manage Content Button.
1
Download content from a disk or source on the network.
2
Download keys [KDM’s] required for playing back content from disk or source on the network.
3
Delete content that exists on the server
.
4
Check that the content that is already on the server is fine and the files are complete and
proper
.
1
2
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 36 -
September 6, 2012
4. CONTENT MANAGER
1
The Content Manager can be accessed from the Control Panel menu. Press the ON/OFF button
on the front panel of the server to switch to the Control Panel menu. Alternatively, press Control
Panel on the Main menu.
2
Press Manage Content to go to the Content Manager main menu.
NOTE: The Content Manager can run in the background and does NOT need to be exited. The
user can leave the Content Manager to go back to the management console by pressing the
ON/OFF button on the server
.
4.2. Content Management
4.2.1. Ingesting Content
Figure 19 Ingesting a package or CPL from a source located in a specific directory in the network.
7
9 3 4 8 6 2 1
5
September 6, 2012
- 37 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
4. CONTENT MANAGER
1
Select the source of data you want to ingest content from and click Open.
Please refer to Section 4.3 Source Management to configure the source of data.
2
Browse the source and select the directory where the package is located. The list of packages
in the directory will be displayed in the top right section of the screen.
3
Click View CPL to display the list of CPLs available in the packages. You can use this button to
toggle between the package list and CPL list displayed in the top right section of the screen.
4
Click under the Transfer column to select the package or CPL you wish to download. A green
check indicates a selected package or CPL. You can select multiple packages or CPLs.
5
Information about the selected package or CPL, including the file size, is shown in the section
below the package or CPL list.
6
Press Import to queue downloading of the package or CPL. (To bypass ingestion for direct
playback you can press Live Play instead. Refer to Live Play below for more info.)
7
When done selecting the package(s), click the Close button.
IMPORTANT: Always press Close after you are done starting the download of content. You
can monitor the progress of ingest by pressing the Status button. Please refer to Section 4.2.6.
Monitor Ingest Progress for more information about Status
.
8
Live Play can be used instead of Import in order to bypass content ingestion and play directly
back from a CRU or network source. This is not supported through USB or DVD but can be
used for direct playback through a CRU or network source (provided the network source has
sufficient bandwidth to stream the content).
IMPORTANT: You should always use Import whenever possible.
9
When you press the Live Source button you can view all clips currently mounted and available
through the Live Play feature. You can detach Live Play sources through this interface as well.
You should always detach live play sources whenever you are done using them via Live Play
.
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 38 -
September 6, 2012
4. CONTENT MANAGER
4.2.2. Ingesting Content from USB Disk
Figure 20 Opening a USB disk connected to the server
1
Select USB drive from dropdown list and click Open. (Continued on next page)
1
September 6, 2012
- 39 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
4. CONTENT MANAGER
Figure 21 Selecting the USB storage device and its partition
2
Select a storage device and its partition from the dropdown lists.
3
Press OK to confirm the selection.
3
2
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 40 -
September 6, 2012
4. CONTENT MANAGER
4.2.3. Ingesting from DVD-ROM Drive
Figure 22 Opening from the DVD-ROM Drive connected to the server
1
Select DVDROM from dropdown list and click Open. (Continued on next page)
1
September 6, 2012
- 41 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
4. CONTENT MANAGER
Figure 23 Selecting the CD/DVD disk from the dropdown list.
2
Select the CD/DVD device from the dropdown list.
3
Press OK to confirm the selection.
4.2.4. Ingesting from CRU DataPort
Figure 24 Powering up the CRU DataPort.
1
Press the GREY button on the front of the CRU DataPort and the blue light will light up.
2 3 1
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 42 -
September 6, 2012
4. CONTENT MANAGER
Figure 25 Opening the CRU DataPort connected to the server
2
Select CRU from dropdown list and click Open. (Continued on next page)
Figure 26 Selecting the storage device and its partition.
3
Select a storage device and its partition from the dropdown lists.
4
Press OK to confirm the selection.
2 3 4
September 6, 2012
- 43 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
4. CONTENT MANAGER
4.2.5. Ingesting KDMs
Figure 27 Ingesting KDM from a directory in the selected source.
1
Select the directory in the selected source where the KDM is located.
2
Shows the KDMs present in the selected directory that are valid for this server
.
3
Click under the Transfer column to select the KDM you wish to download. A green check
indicates the selected KDM.
4
Shows the details of the selected KDM, including target, CPL, and date of validity
.
5
Press Import to start the import of the KDM. The green check will change to Queued
.
6
When done selecting the KDM, press Close to close the Package Browser
.
1
6 2 3 54
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 44 -
September 6, 2012
4. CONTENT MANAGER
4.2.6. Monitor Ingest Progress
Figure 28 Monitoring the progress of download of the packages.
1
Select the Status option.
2
Shows the download status of the packages or CPLs. In this example, downloading of some
packages or CPLs is incomplete.
2
1
September 6, 2012
- 45 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
4. CONTENT MANAGER
4.2.7. Cancelling Ingest
Figure 29 Content Manager - Status
1
Press Pause to temporarily stop the download of the package(s) or CPL(s). The Pause button
will change to Start and will indicate that the download is being paused.
2
Use the Move Up and Move Down buttons to move the highlight bar up and down to select the
desired package or CPL when multiple packages or CPLs are being downloaded. You can only
move the highlighted bar to select the package or CPL when in Pause mode.
3
To cancel the download, select the desired package or CPL and press Remove
.
4
If you wish to resume download, press Start button to resume the download.
1
3
2
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 46 -
September 6, 2012
4. CONTENT MANAGER
4.2.8. Deleting Content
Figure 30 Deleting a downloaded package or CPL
1
To delete a package or CPL, go to Content menu and click under the Select column opposite
the package or CPL you want to delete. A green check
indicates the selection.
2
Click View CPL to toggle between the package and CPL lists displayed in the content menu.
3
You can select all by clicking the Select All button, and deselect by clicking the Deselect All
button.
4
Press Delete to delete the selected package or CPL. A small window pops up to confirm the
deletion of the package.
Press OK to confirm.
2 1 3
4
September 6, 2012
- 47 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
4. CONTENT MANAGER
4.2.9. Checking Content Integrity
Figure 31 Verifying the integrity of the files in the package(s) or CPL(s).
1
Click View CPL to toggle between the package and CPL lists displayed in the content menu.
Click under the Select column opposite the package or CPL you want to verify. A green check
indicates the selection.
2
Select if you want to verify Now or on a Schedule
.
1
2
3
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 48 -
September 6, 2012
4. CONTENT MANAGER
3
Press Verify to check if all the required files are present in the selected package(s) or CPL(s).
(a) If Now is selected, the package will be verified immediately as seen below
.
(b) If Schedule is selected, you need to assign a name and schedule the time and date when
to verify the package(s) or CPL(s) in a new window as seen below
.
(c) You can select the frequency of verification.
September 6, 2012
- 49 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
4. CONTENT MANAGER
Figure 32 Checking for stray files in package(s) or CPL(s)
4
You can check if there are stray files in the selected package(s) or CPL(s) by pressing Check
Stray. A small window pops out to confirm if there are no stray files.
4
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 50 -
September 6, 2012
4. CONTENT MANAGER
Figure 33 Package [Quick Verify]
5
Select Quick Verify to quickly check the integrity of the files in case it is modified or corrupted by
calculating hash for each file in the selected package(s) or CPL(s).
6
You will see OK under the Status column after verifying that no problems are detected. If errors
are found, the description of the error will be shown instead as seen in Figure 33 above.
NOTE: If there is an error in the selected package, it will indicate Failed under the Status
column.
6
5
September 6, 2012
- 51 -
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
4. CONTENT MANAGER
Figure 34 Content Manager [Schedule].
7
You can view the list of package(s)/CPL(s) that you have scheduled for verification by selecting
the Schedule option.
8
Select the desired package or CPL and press View to see its schedule details.
9
Select the desired package or CPL and press Remove to delete it from the schedule list.
7 8 9
Remove
SX-2000A Series with Integrated Media Block/SX-2001A Series
User Manual
(Short Form Version)
- 52 -
September 6, 2012
4. CONTENT MANAGER
4.3. KDM Management
4.3.1. Manage KDM
Figure 35 KDM Manager.
1
Select the KDM tab in the Content Manager menu.
2
Show the KDMs present in the selected directory that are valid for this server
.
3
Show the details of the selected KDM, including target, CPL, UUID and date of validity
.
4
Display date of issue for KDM.
5
Verify the integrity of the KDM.
6
Delete removes KDM from the server.
4 1 3 5 6
2
5. SERVER OPERATION NOTES
5. SERVER OPERATION NOTES
5.1. Important Notes
Each time, server boot will take up to five (5) minutes.
In the event of power loss or forced shutdown, server boot may take up to twenty (20)
minutes. The server must complete bootup before playback can be started. It is
recommended to ALWAYS follow proper power up & shutdown procedures (see
section 5.2.).
The SMS will be locked by default.
Ethernet Connection between the Server, SM and Projector is REQUIRED for
successful playback. Customers must ensure the cable is secure and the switch used
(in case of non-IMB systems) is reliable.
5.2. Power Up & Shutdown
This section lists the proper power up and shutdown steps that will result in the most
optimal performance for the servers.
5.2.1. Power Up
a) Power up the projector first and then the server. This is necessary for IMB board
servers to operate properly.
b) It is recommended to reboot the projector if it has been idle longer than 3 minutes
without the connected server powered on.
5.2.2. Shutdown
a) Always shutdown the servers before the projector. This is a MUST for IMB servers.
b) Always use the shutdown option from the server interface. Do not unplug the power,
switch off the power switches, or hold down the power button during normal use.
GDC Technology Offices
USA (Los Angeles, CA)
1016 West Magnolia Boulevard
Burbank,CA 91506, USA
Tel: +1 818 972 4370/
+1 877 743 2872 (Toll Free)
USA (Sterling, VA)
21155 Whitfield Place, Suite 207,
Sterling, VA 20165, USA
Tel: +1 877 337 0868 (Toll Free)
Spain (Barcelona)
Av. Diagonal, 177, 9th Floor
08018 Barcelona, Spain
Tel: +34 93 238 14 10
Hong Kong
Unit 1-7, 20th Floor,
Kodak House II,
39 Healthy Street East,
North Point, Hong Kong
Tel: +852 2523 6851
Japan (Tokyo)
7F Nishino Kinryo Bldg,
4-9-4, Hatchobori, Chuo-ku,
Tokyo 104-0032, Japan
Tel: +81 3 3523 2650
Singapore
6 Changi South Street 2,
Fedex Building, Level 7,
Singapore 486349
Tel:
+65 6222
1082
China
(Shenzhen)
5th Floor GDC Building,
No.9 Hi-tech Middle 3 Road,
Science & Technology Park,
Nanshan District,
Shenzhen, P.R. China
518057
Tel: +86 755 8608 6000
China (Beijing)
Rm. 609-618, Office Building,
20# Xinde Street,
Xicheng District,
Beijing, P.R. China 100088
Tel: +86 10 6205 7040
Email:
inf
o@gdc-t
ech.com
Website:
www
.gdc-t
ech.com
ISO 9001 QMS
Cert. No. CN09/32 221
GDC
manufacturing
facility
is ISO 9001: 2008
cer
tified.
Copyright © 2012 GDC Technology
Limited.
All
rights reserved.
All
trademarks
list
ed
in this manual are properties of their respective owners.
Specifications are subject to
change without notice due to ongoing
product development and
improv
ement.
UM-0142-1209-V1E
Loading...