Size:
401.02 Kb
Download

AG-168VSIP GATEWAY User Manual (V1.42)

AG-168VSIP GATEWAY User Manual

AG-168VSIP GATEWAY Appearance Introduction: ......................................................

2

 

Features ................................................................................................................................

2

Function Keys of AG-168VSIP GATEWAY Introduction...........................................

3

 

Standard and Protocol.........................................................................................................

4

 

Operating requirements ......................................................................................................

5

 

Electric requirements ...........................................................................................................

5

 

Size ........................................................................................................................................

5

 

Installation .............................................................................................................................

6

 

Configuration.........................................................................................................................

6

 

GATEWAY Keypad set ........................................................................................................

6

 

Configured by WEB .............................................................................................................

7

 

Configured by PalmTool ....................................................................................................

23

 

Telnet Configuration ...........................................................................................................

23

 

Use AG-168VGateway .....................................................................................................

41

 

Upgrade AG-168VSIP GATEWAY................................................................................

43

AG-168VSIP GATEWAY User Manual (V1.42)

Gateway Front Illustration:

Features

2

AG-168VSIP GATEWAY User Manual (V1.42)

Indicator light and function

Indicator

Function

 

Indicator

Function

light

 

 

light

 

Power

Power on ,indicating power

 

Status

Registered off, not registered flash

Tel

communicaing flash,

 

 

 

Buttons

 

Function

 

 

voice indicating “local ip ” , refer to “GATEWAY Keypad set” chaptor

 

 

 

set different way of internet connection, refer to “GATEWAY Keypad set” chaptor

IP

Set static ip address when in “static mode ”

enable AG-168Vinto “setting mode ”, refer to “GATEWAY Keypad set” chaptor

Hardware

Main chip—pa1688PQ50MHz

Data Memory—1MBSDRAM

Program Memory—2MBFlash memory

Ethernet Jack—110M jacks

FXS Port-1FXS Port for Tel

Line Port -1Line port for PSTN

AC/DC adapter—Output12V DC, 450mA

Software

DHCP support for LAN or Cable modem

PPPoE support for ADSL or Cable modem

Set GATEWAY by HTTP web browser (IE6.0) or Telnet

Upgrade by FTP

Support major G.7XX and gsm610 audio codec

3

AG-168VSIP GATEWAY User Manual (V1.42)

Dynamic voice jitter buffer

G.168/165 compliant 16ms echo cancellation

Tone generation and Local DTMF re-generationaccording withITU-T

E.164 dial plan and customized dial rules

100 entries for quick dial

Voice prompt

Hotline

Standard and Protocol

Gateway supports following standard and protocol:

IEEE 802.3 /802.3 u 10 Base T / 100Base TX

Major G.7XX and gsm610 audio codec

SIP RFC3261

TCP/IP: Internet transfer and control protocol

RTP: Real-timeTransport Protocol

RTCP Real-timeControl Protocol

VAD/CNG save bandwidth

DHCP Dynamic Host Configuration Protocol

PPPoE Point to Point Protocol over Ethernet

DNS Domain Name Server

Telnet Internet's remote login protocol

FTP File Transfer protocol

HTTP Hyper Text Transfer protocol

Operating requirements:

Operation temperature: 0 to 50°C (32°to 122°F)

Storage temperature: -30°to65°C(-22°to149°F)

Humidity: 10 to 90% no dew

Electric requirements:

Voltage: 9V~12V DC

Power adapter: DC 12V/450mA

4

AG-168VSIP GATEWAY User Manual (V1.42)

Network interface:1 RJ-45Ethernet Connectors

FXS:1 RJ-11For Tel

Line:1 RJ-11For PSTN

Size

150 x 110 x 28 mm (L x W x H)

Installation:

1 Connecting to network: connecting one side of the cable to the lan port of AG-168V,the other side to PBX or HUB or ADSL and Cable Modem’s lan port..

2Connecting to phone: Insert one side of RJ11 line to the Tel port of AG-168V ,the other side to the phones’ interface. Connecting the Line’s port ofAG-168Vto PSTN line. Power on with the adaptor from the packaging.

5

AG-168VSIP GATEWAY User Manual (V1.42)

Configuration

Two different ways can be used to configure AG-168VH323 phone: phone web browser, Telnet commands on computer.

Phone Keypad setup

Using the keyboard of the normal phone connecting to AG-168VFXS port and the “IP key” , which can preset and enter into “Setting mode” , operation as below:

Operation

 

Function

IP

1

with handset of FXS port ‘s phone hung, press IP ,voice promt “local ip”

 

 

 

 

 

 

 

2

with handset of FXS port ‘s phone hung, press default password, then

 

input the number of X + “

IP” button in order to set different network

 

connection

 

1234+X+ IP

 

 

 

 

 

X valued 0 = stataic IP;

1 = DHCP ; 2 = PPPoE; 3= modem

 

 

 

 

3

with handset of FXS port ‘s phone hung, press default password, and

1234+ IP

press “ IP” button, enter “setting mode”

 

 

 

1234+xxx.xxx.xxx.xx

4

with handset of FXS port ‘s phone hung, press default password, then

 

 

 

 

 

 

 

6

 

AG-168VSIP GATEWAY User Manual (V1.42)

 

 

x

input the ip address xxx.xxxx.xxx.xxx, press “ip ” button . Using the button

+ IP

of * for ,

Configured by WEB

Double click icon to open the IE browser. Input the IP address of the GATEWAY

into address bar ( ), and then input password of the

GATEWAY into the following page. Default password 1234 is ordinary password and super password is 12345678. With Debug set 0[disable], please input super password; while Debug is not set as 0[disable], please input ordinary password. Then clickbutton. The following configured page wills popup. Refer to Fig 3.1 please.

7

AG-168VSIP GATEWAY User Manual (V1.42)

Fig 3.1 Http Setting

Network Setting

Fig 3.2 Network Setting

iptype: Set how IP GATEWAY gets relevant network parameters by selecting

corresponding item from drop down list.

static ip: Select this item to authorize users set IP address, subnet mask and

router IP address of IP GATEWAY manually.

dhcp: Select this item to enable DHCP mode. With this system, your LAN or router

automatically assigns all the required network parameters to any device connected

to it when the device log on. AG-168VIP GATEWAY is shipped from the factory

with DHCP on. So, if you’re LAN or router is configured to use DHCP addressing,

the IP GATEWAY’s LAN parameters will automatically be configured as soon as it is

connected to the LAN or router and powered up.Default IP address of the AG-168V

is192.169.1.100.

pppoe Those ADSL and Cable Modem users please select this item for it is a

protocol especially designed for them. With this system, ADSL ISP automatically

assigns all the required IP parameters to any device connected to it when the

device log on.

modem If the IP GATEWAY used with modem, please select this item to get

8

subnet mask:

AG-168VSIP GATEWAY User Manual (V1.42)

relevant network parameters auto. Then please fill ID and pin into ppp id and

ppppin fields.

ppp id: Withpppoe ormodem selected iniptype drop down list, please enter the

user name here.

ppp pin: Withpppoe ormodem selected iniptype drop down list, please enter the

password here.

local ip: Withstatic ip selected iniptype drop down list, please enter IP address of

IP GATEWAY here.

With static ip selected iniptype drop down list, please enter subnet mask of IP GATEWAY here.

router ip: Withstatic ip selected iniptype drop down list, please enter router IP

address of IP GATEWAY here.

dns: Withstatic ip selected iniptype drop down list, please enter IP address of

DNS server here.

dns 2: Withstatic ip selected iniptype drop down list, please enter IP address of

backup DNS server here.

mac: MAC address is the physical

AG-168VGATEWAY is shipped from

address supplied by the Ethernet NIC.

the factory with a unique algorism MAC

address printed on the back of the base.

9

register ttl:

AG-168VSIP GATEWAY User Manual (V1.42)

Protocol Setting

Fig 3.3 Protocol Setting

use service: Enable/disable service by checking/clearing this box.

To make calls through gatekeeper, please check this box; otherwise, GATEWAY can only make IP-toIP calls or calls through gateway.

IP phone will send a keep-aliveregistration message to SIP proxy server every “register ttl” seconds. The minimum value is 10, maximum value is 65535. Default is 60.

service type: This option is used to accommodate the miscellaneous requirements of the system providers. When IP GATEWAY is connected to these systems, please select the corresponding service type.

common no special requirements

huawei: use huawei’s system

zte: use zte’s system

harbour: use harbour’s system

utstarcom: use utstarcom’s system

uptech: use uptech’s system

10

AG-168VSIP GATEWAY User Manual (V1.42)

kaimen use kaimen’s system

mediaring: use mediaring’s system

italkbb: use italkbb’s system

stanaphone: use stanaphone’s system

net2phone: use net2phone’s system

fwd: use fwd(freeworlddialup) system

ipphonex: use ipphonex’s system

sipphone: use siphone’s system

ngtel: use ngtel’s system

ayctel: use AycTe’s system

SIP proxy: when user service write SIP Proxy Server URI.

Domain/realm : set SIP serve address domain

nat traversal: When the IP GATEWAY with private IP address need communicate

with other IP GATEWAYs in a different LAN or on Internet, please select an item from dropdown list to set the proxy used by the GATEWAY.

disable: Select this item when the log in server and IP GATEWAY in the same LAN, or the log in system supports the IP GATEWAY working behind the LAN.

enable: When the system does not support IP GATEWAY working behind the LAN, please select this item to search public IP address of the NAT device. With this item selected, “nat addr” field will be activated. Besides, port mapping (port forwarding) needs to be properly set up on NAT device.

Stun: When Stun used for appendix for cross NAT , choose STUN.nat add will be activated.

nat addr: When “nat traversal” is set to “enable”, please put the domain name of

the servers ( These web server helps to find out the public IP of the IP GATEWAY) into “nat addr”, such aswww.whatismyip.com.

nat ttl: When IP GATEWAY sit behind a NAT device, it will send packets to server

11

AG-168VSIP GATEWAY User Manual (V1.42)

every “nat ttl” seconds to keep the port mapping on the NAT device alive. “nat ttl” is an integer between 10 and 65535 .default value is 20.

phone number: set local ID .

account: set aaa@bbb format account register.

pin: set password.

register port: The local UDP port registered with server to accept incoming

handshaking messages. Default is 5060

rtp port : RTP port is the port transferring and receiving voice packets using UDP

protocol. This is an even number between 1024 and 65535, can’t be the same as

register port”.

rtp tos: Set the TOS field of the IP header of the RTP packets. The bigger this

value is 0, the higher priority the packet is.

local type: This parameter refers to how IP GATEWAY authenticate itself to the

gatekeeper. The meaning of each item is as follow:

auto: use support automated negotiate authentication account and pin about MD5 or CAT .

md5: use MD5 authentication account and pin.

cat: use CAT authentication account and pin.

sha1: use SHA1 authentication account and pin.

call type: Set call type by selecting the items in drop down list.

normal: Call out in normal way by selecting this item.

advanced: Call out in faststart and tunneling way by selecting this item. It is a

12

AG-168VSIP GATEWAY User Manual (V1.42)

recommended way with SIP protocol used.

dtmf: Set DTMF signal sending way by selectingcontrol string,inband audio,

signal keypad or rfc 2833 ,sip infofrom list box.

dtmf payload: set use RTP send DTMF’s RTP the value range is96-101

register ttl : IP GATEWAY will send akeep-aliveregistration message to SIP

gatekeeper every “register ttl” seconds. The value range is10-65535.Default is 60.

Super password : Set super password. Default is 12345678

debug: Set the debug level of the GATEWAY.

disable: Disable output the debug message by selecting this item.

output: Output the operation information to the window, such as register, input

by selecting this item.

output all: Output all debug information and data in test window by selecting this

item.

remote debug: Save the debug information in SDRAM of IP GATEWAY by

selecting this item.

no check: Disable checking firmware tags when upgrading. This is not

suggested, because it will increase the risk of upgrading the wrong firmware into

the GATEWAY.

phone settings:

13

AG-168VSIP GATEWAY User Manual (V1.42)

Fig 3.4 phone Setting

use dialplan: Set whether use dial plan or use dial number by selecting the

corresponding item in drop down list.

disable: Do not use dial plan or dial number by selecting this item.

enable: Use dial plan by selecting this item.

dialnum: Use dial number by selecting this item. With this item selected, please

enter the dial prefix into dial number field.

prefix: Use 179XX service by selecting this item.

Hotline: Use Hotline function by selecting this item. With this item selected, please enter the hotline number intodial number field.

dial number: Withdialnum selected inuse dialplan drop down list, please

enter the dial prefix into this field according to requirement of log in server. For

example, with eTalk card used, enter 00 here.

ddd code: Withenable ordialnum selected inuse dialplan drop down list, set

area code according to E.164 dial rule. For example, Beiing 10; Shanghai 21.

idd code: Withenable ordialnum selected inuse dialplan drop down list, set

country code according to E.164 dial rule. For example, China 86; U.S.A .1.

idd prefix: Withenable ordialnum selected inuse dialplan drop down list, set

international call prefix according to E.164 dial rule, such as 00.

14

AG-168VSIP GATEWAY User Manual (V1.42)

ddd prefix: Withenable ordialnum selected inuse dialplan drop down list, set

long distance call prefix according to E.164 dial rule, such as 0.

inner line: Enable/disable innerline call by selecting corresponding items from dropdown list.

disable: Disable call innerline by selecting this item.

enable: enable call innerline by selecting this item.

omit prefix Enable , ingnore the number of the inner line prefix , cooperated

with special system

inner line prefix: default is 0.

nonlocal prefix: Withenable selected ininnerline dropdown list, please fill the

number switching to long-distancecall, such as 9.

Call waiting: Enable/disable call waiting by checking/unchecking the box.

Use digitmap: Enable/disable digit map by checking/unchecking the box.

forward number: Enter receiving forwarded calls GATEWAY number into this

field; If the IP GATEWAY used with modem, with modem item selected iniptype list box, and then fill ISP number into this field.

fwd poweroff: Forward calls if power off by checking this box. Please enter

receiving forwarded calls GATEWAY number into fwd number field.

fwd noanswer: Forward calls without replying by checking this box. Please enter

receiving forwarded calls GATEWAY number into fwd number field.

fwd always: Forward all calls by checking this box. Please enter receiving

15

AG-168VSIP GATEWAY User Manual (V1.42)

forwarded calls GATEWAY number into fwd number field.

fwd busy: Forward calls if busy by checking this box. Please enter receiving

forwarded calls GATEWAY number into fwd number field.

answer: Enter a number from 0 through 60 to set the entries of the seconds before the GATEWAY answer the call auto or forward the calls.

handset in: Drag the slider to adjust the volume of handset input. Drag it to the left to reduce the volume; while drag it to the right to increase the volume.

handset out: Drag the slider to adjust the volume of handset output. Drag it to the left to reduce the volume; while drag it to the right to increase the volume.

Dual mode setAG-168VFXS PSTN port

disable AG-168VFXS Not user PSTN

PSTN first setAG-168VFXS first user PSTN call

IP first setAG-168VFXS first user ip call

dual mode prefix set dual mode prefix IP first set PSTN prefix

Audio settings:

Fig 3.5 Audio Setting

vad: Enable/disable VAD (voice activity detection).

agc: Enable/disable AGC.

aec: Enable/disable VEC.

codec1: Set the priority 1of the audio compression algorithm. The options are

g729 g7231 g711u g711a and gsm.

codec2: Set the priority 2of the audio compression algorithm. The options are

16

codec4:
codec3:

AG-168VSIP GATEWAY User Manual (V1.42)

g729 g7231 g711u g711a and gsm.

Set the priority 3of the audio compression algorithm. The options are g729 g7231 g711u g711a andgsm.

Set the priority 4of the audio compression algorithm. The options are g729 g7231 g711u g711a andgsm.

codec5: Set the priority 5of the audio compression algorithm. The options areg729 g7231 g711u g711a andgsm.

g.723.1 high rate: enable/disable g.723.1 high rate. G.723.1 high rate is 6.3kbps,

low rate is 5.3kbps.

Other settings:

Fig 3.6 Other Setting

password: Set the password of the GATEWAY. (Default password is 1234).

Upgrade type: user FTP upgrade

disable: Disable output the debug message by selecting this item.

all: check hard type upgrade.

mac: check mac address auto upgrade.

Ppp id: check pppid auto upgrade.

account: check account auto upgrade.

17

AG-168VSIP GATEWAY User Manual (V1.42)

Phonenumber: check phonenumber auto upgrade.

upgrade addr: Put IP address or domain name obtained by ISP of FTP server

supplying upgrade program into this field.

nts ip: Fill IP address of time server here.

use daylight: Enable/disable daylight.

timezone: Select correct time zone in list box.

When debug set as 0[disable], if input ordinary password (default one is 1234), then following page will pop up after clicking . And only those parameters can be modified.

Fig 3.7 Setting Page using ordinary pin with Debug set as 0 [disable]

Update: Click this button to save the configuration and the GATEWAY will reboot. Once the GATEWAY reboots successfully, the new configuration is effective.

Note After entering set page, ifUpdate button is not clicked within 5 seconds, then when you click it again, the index page asking for pin will pop up again. Then please input the password again to enter the set page and then clickUpdate

18

AG-168VSIP GATEWAY User Manual (V1.42)

button to confirm the modification.

phone Book: Click this button to open the speed dial settings page. Please refer to Fig 3.7. In this page, you can set and save the speed dial number by typing the name into theName field and then entering the corresponding number following the name. For example, input Jack in Name field following 001, and then input 5989426454 into GATEWAY number field. Then Jack’s number 5989426454 is saved in GATEWAY book. Then please clickSave/Back button. In normal state, you can use speed dial to call numbers saved in GATEWAY book.

Fig 3.8 GATEWAY Book Illustration

Upgrade Program: Click this button to update the program of IP GATEWAY. Before updating, please fill IP address of FTP server intoupgrade addr field, and then click this button. Then the GATEWAY will read the corresponding bin files from the server and then load into the GATEWAY.

Update Digitmap: Click this button to update the digitmap of the GATEWAY. Before updating, please fill IP address of FTP server intoupgrade addr field, and then click this button. Then the GATEWAY will read the corresponding map files from the server and then load into the GATEWAY.

Note Please refer toPalmTool User Guide to learn how to write digitmap or just download TXT file from our site. Then please save it as “GATEWAY type.map” file, such as AT168S.map.

Configured by PalmTool

PalmTool is a tool designed especially to configure and upgrade the PA168 IP GATEWAY. On a PC

19

AG-168VSIP GATEWAY User Manual (V1.42)

connecting with the GATEWAY or at the same segment of the GATEWAY, double clickicon to

open the PalmTool. The index page of PalmTool will popup.

a)Input the IP address of the GATEWAY into Local IP field (such as 192.168.1.100), and then click “GATEWAY Settings” button.

From Version1.24, use PalmTool to set the IP GATEWAY, please set debug as output or output all firstly, or PalmTool cannot connect IP GATEWAY. The parameters of PalmTool is same as the parameters in HTTP, so please refer to HTTP set chapter to learn how to set IP GATEWAY.

Telnet Configuration

On the PC choose Start>Run, and then typetelnet 192.168.1.100 intoRun field in popuping Run dialog. Or inputtelnet 192.168.1.100 in the DOS window. Then the following information will be displayed.

AG-168VV1.39 settings

Password :

Then please type password. With debug is set as 0[disable], if type ordinary password (default one is 1234), after Retun, you will see

Password : ****

P:\>

If you type super password, then you will see:

Password : ********

P:\>

Above information indicates that IP GATEWAY is under setting mode, and then you can set the AG-168VIP GATEWAY by using the telnet commands.

AG-168VTelnet Commands Explanation

AG-168VTelnet Commands

Comman

Function

d

 

?

Supply command name and parameters

20

AG-168VSIP GATEWAY User Manual (V1.42)

get

Display basic parameters of the AG-168VIP GATEWAY

set

Set parameters of the AG-168VIP GATEWAY

store

Save current settings to designated position

load

Load designated settings to current position

exit

Exit from the setting mode without saving the configuration

write

Exit with saving all configurations and restart AG-168V

ping

Ping other net parameter

ftp

The GATEWAY connects to FTP server and then get the files

Detail description of AG-168VTelnet commands

Command ?

Syntax description: No optional parameter

Usage: Type command name and parameters following P:\> . Be used as the

keyword to supply keyword and parameters of the relevant commands.

Relevant usage: None

Detailed description:

List help of all commands

For example:

P:\>?

 

set

 

get

list settings

store x

store current to xth settings

load x

load xth settings to current

exit

 

write

save settings

 

 

 

 

Command get

21

AG-168VSIP GATEWAY User Manual (V1.42)

Syntax description: No optional parameter of keywords

Usage: Display basic parameters of theAG-168VIP GATEWAY

Relevant usage: None

Detailed description:

get Display basic running parameters of theAG-168VIP GATEWAY.

Input ordinary password without debug being set as 0[disable], or input super

password with debug set as 0[disable], then following parameters of IP GATEWAY

will be displayed:

AG-168VV1.39 settings

 

 

 

Password: ********

 

 

 

P:\>get

 

 

 

iptype 0[static]

 

 

 

ip 192.168.1.100

subnetmask 255.255.255.0

router 192.168.1.254

dns 202.106.196.152

dns2 202.106.196.115

mac 00-09-45-65-a3-e6

service 1[enable]

 

 

 

servicetype 0[common]

serviceaddr 203.93.9.57

serviceid [empty]

nattraversal 1[enable]

nataddr www.showmyip.com natttl 30

GATEWAYnumber 182378009 account [empty]

 

pin [empty]

registerport 6800

signalport 6800

controlport 6802

registerttl 60

rtptos 0

rtpport 6802

jitter size 0

 

 

 

calltype 1[advanced]

localtype 0[GATEWAYnumber]

dtmf 0[control

string]

 

 

 

dtmfpayload 101

 

 

 

dialplan 2[dialnum]

dialnumber 17911

dddcode [empty]

iddcode [empty]

iddprefix [empty]

dddprefix [empty]

innerline 1[enable]

localprefix 0

nonlocalprefix 0

answer 5

ringtype 0[dtmf0]

digitmap 0[disable]

fwdnumber [empty]

fwdpoweroff 1[enable]

 

 

fwdalways 0[disable]

fwdbusy 0[disable]

fwdnoanswer 0[disable]

audiotype 0[g7231]

audioframes 1

 

6.3k 1[enable]

vad 1[enable]

agc 0[disable]

aec 1[enable]

handsetin 9

handsetout 21

 

speakerout 21

codec1 1[g7231]

codec2 0[g729]

codec3 2[g711u]

codec4 4[gsm]

codec5 5[null]

 

 

22

AG-168VSIP GATEWAY User Manual (V1.42)

password 1234

superpassword 19750407

debug

1[output]

 

 

upgradeaddr [empty]

 

 

sntpip 0.0.0.0

daylight 0[disable]

 

timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi]

Input ordinary password with debug set as 0[disable], following information will be seen:

AG-168VV1.39 settings

 

 

Password:****

 

 

P:\>get

 

 

iptype 0[static]

 

 

ip 192.168.1.100 subnetmask 255.255.255.0

router 192.168.1.254

dns 202.106.196.152

dns2 202.106.196.115

 

nattraversal 1[enable]

nataddr

rtpport 5144

registerport 5142

signalport 5142

controlport 5144

account [empty]

pin [empty]

 

GATEWAYnumber 182378009 fwdpoweroff 0[disable]

fwdalways 0[disable]

fwdbusy 0[disable]

fwdnoanswer 0[disable]

ringtype 0[dtmf0]

answer 5

 

password 1234

 

 

upgradeaddr [empty]

 

 

sntpip 0.0.0.0

daylight 0[disable]

 

timezone 55[(GMT+08:00)Beijing,Hong Kong,Urumqi]

Command set

Syntax description: set keywords value

Usage: Used to configure password and other running parameters ofAG-168V

IP GATEWAY.

Detailed description:

set iptype X

Set how IP GATEWAY gets relevant network parameters. X ranged from 0

through 3: 0: authorize users set IP address, subnet mask and router IP

23

AG-168VSIP GATEWAY User Manual (V1.42)

address of IP GATEWAY manually; 1: use DHCP mode. With this system,

your LAN or router automatically assigns all the required network parameters

to any device connected to it when the device log on. AG-168VIP

GATEWAY is shipped from the factory with DHCP on. So, if your LAN or

router is configured to use DHCP addressing, the IP GATEWAY’s LAN

parameters will automatically be configured as soon as it is connected to the

LAN or router and powered up; 2: use PPPoE mode. Those ADSL and Cable

Modem users please select this item for it is a protocol especially designed

for them. With this system, ADSL ISP automatically assigns all the required

IP parameters to any device connected to it when the device log on; 3: use

modem mode. Those who use IP GATEWAY with modem, please set the

value as 3.

set pppid XXX

With iptype set as2, use this command to set ADSL ID; withiptype set as3,

use this command to set Modem ID.

set ppppin XXX

With iptype set as2, use this command to set ADSL pin; withiptype set as3,

use this command to set Modem pin.

set ip XXX.XXX.XXX.XXX

With iptype set as0, use this command to set IP address ofAG-168VIP

GATEWAY.

set subnetmask XXX.XXX.XXX.XXX

24

AG-168VSIP GATEWAY User Manual (V1.42)

With iptype set as0, use this command to set subnet mask ofAG-168VIP

GATEWAY.

set router XXX.XXX.XXX.XXX

With iptype set as0, use this command to set router IP of network with

AG-168VIP GATEWAY.

set dns XXX.XXX.XXX.XXX

With iptype set as0, use this command to set IP address of DNS server.

set dns2 XXX.XXX.XXX.XXX

With iptype set as0, use this command to set IP of backup DNS server.

set mac XX-XX-XX-XX-XX-XX

Set MAC address of the AG-168VIP GATEWAY. Parameter

xx-xx-xx-xx-xx-xxmust be an HEX number.

set service X

Set register the gatekeeper or not. X ranged from 0 through 1. 0: do not

register; 1: register.

set service type X

Enable/disable the repaid and service system .choose the repaid server

provider. Parameter x ranged from 0 through 29:

0:common: disable repaid card; 4: use Mediaring service; 2: use eTalk card;

3:use Auvtech system; 5: use Ringtec service; 6: use Smartcon service; 7:

use dda service; 8: use vida service; 9: use citron system; 10: use asiasoft

system; 12: use zte system; 13: use huawei system; 16: use asiainfo system;

25

AG-168VSIP GATEWAY User Manual (V1.42)

17: use Lucent system; 19: use IPN system; 20: use yayuang system; 21:

use thinker system; 22: use suntek system; 28: use txtc system.

set serviceaddr XXXX

Set IP address or domain name of gatekeeper.

set serviceid XXXXX

Set service ID according to required by service system.

set nattraversal X

Set NAT traversal or not. X ranged from 0 through 7: 0: do not use. When the

log in server and IP GATEWAY in the same LAN, or the log in system

supports the IP GATEWAY working behind the LAN; 1: Use NAT traversal.

When the login system does not support IP GATEWAY working behind the

LAN, please use this value to search public IP address of the NAT device.

With this item selected, please make port mapping on NAT device; 2: With

Citron private protocol used, use this value to fit into the GnuGK system

transferring the voice and signal by router; 3: use this value with Innopath

private system used; 5: use this value with vida private system used; 6: aivgr

use this value with aivgr private system used; 7: use this value with Eproxy

private system used.

set nataddr XXXXX

Set IP address of NAT device wan port or URI of free assistant service (Such as www.showmyip.com etc.) in Internet.

NOTE The free service list of Internetwww.ip-calculator.com;www.ipchicken.com;

26

AG-168VSIP GATEWAY User Manual (V1.42)

www.ipchicken.com;www.showmyip.com;www.whatismyip.com; www.myipaddress.com; www.whatismyipaddress.com; ip.sbbs.net; www.whatismyipaddress.net;checkip.dyndns.org

set natttl XX

Set NAT TTL XX is an integer between 10 and 65535 sec. default value is 20

sec.

set GATEWAYnumber XXXXXXXX

Set a GATEWAY number of AG-168VIP GATEWAY . Value xxxxx must be

an Arabic numeral and no longer than 16 characters.

set account XXXXXX

While calling card is set, set account of chosen card; while local type is set

use authentication type, set user ID; while set localtype is set as 1, set SIP

ID.

set pin XXXXXXXXXX

While calling card is set, set password of chosen card; while local type is set

authentication type, set password.

set registerport XXXX

Set register port. XXXX is range from 1024 through 6553.

set signalport XXXX

This port is Q.931 port using TCP protocol. XXXX is range from 1024 through

65535.

set controlport XXXX

This port is H.245 port using TCP protocol. XXXX is range from 1024 through 65535.

27

AG-168VSIP GATEWAY User Manual (V1.42)

set registerttl X

Set register TTL. X is range from 10 through 65535 Sec. default value is 60

Sec.

set rtptos X

Set TOS segment of IP head package in RTP digital follow.

set rtpport XXXX

RTP port is the port transferring and receiving voice flow using UDP protocol.

XXXX is range from 1024 through 65535.

set jittersize X

Set buffer size of RTP package. X is range from 0-32.

set calltype X

Set call type of the GATEWAY. X is ranged from 0 through 2: 0: call out in

normal way; 1: call out in faststart and tunneling way. It is a recommended

way.

set localtype X

This command used to set how IP GATEWAY log in gatekeeper. X is

ranged from 0 through 6: 0: use GATEWAY number as E.164 and SIP ID to

login the GK; 1: use GATEWAY number as E.164 and designated SIP ID by

set account XXX command; 2:use support automated negotiate about MD5

or CAT authentication system.3:use MD5 authentication account and pin;4:

use CAT authentication account and pin; 5: use SHA1 authentication

account and pin.

set dtmf X

28

AG-168VSIP GATEWAY User Manual (V1.42)

Set DTMF relay type. X is ranged form 0 through 3: 0:control string 1:inband

audio 2: signal keypad 3:rfc 2833.

set dtmf payload X

When dtmf X select 3(rfc 2833).This parameter can be used indicating type of RTP payload type. The value can be use integer96-101.

set dialplan X

Enable/disable dial plan and dial number. Parameter X ranged from 0

through 4: 0: disable dial plan; 1: enable dial plan; 2: use dial number; 3: use

179XX service.;4: use hotline function.

set dialnumber XX

When set dialplan value set as 2, please use this command to setdial

number. For example, with eTalk card used, please set it as 00. Whenset

dialplan value set as 4, please use this command to sethotline number.

set dddcode XX

Set the area code when set dialplan value set as1 or2. For example, the

area code of Beijing is 10; the area code of Shanghai is 21, and the area

code of Chengdu is 28, etc. Parameter xxx must be an Arabic numeral and

no longer than 3 characters.

set iddcode XXX

Set the country code when set dialplan value set as1 or2. For example, the

country code of China is 86; the country code of USA is 1, etc. Parameter

xxxx must be an Arabic numeral and no longer than 4 characters.

29

AG-168VSIP GATEWAY User Manual (V1.42)

set iddprefix XX

Set IDD service prefix number when set dialplan value set as1 or2. For

example, IDD service prefix number of china is 00; IDD service prefix number

of USA is 1, etc. Parameter xxx must be an Arabic numeral and no longer

than 3 characters.

set dddprefix XX

Set DDD service prefix number when set dialplan value set as1 or2. For

example, DDD service prefix number of china is 0; DDD service prefix

number of USA is 1, etc. Parameter xxx must be an Arabic numeral and no

longer than 3 characters.

set innerline X

Set use innerline call or not. X ranged from 0 through 1: 0: disable; 1: enable innerline call.

set localpreifx X

With innerline set as1[enable] , please set the number switching to local call, such as 9.

set nonlocalprefix X

With innerline set as1[enable] , please set the number switching to

long-distancecall, such as 9.

set answer X

Set the ring seconds before the GATEWAY answers the call auto or forward

the calls. X is ranged from 0 through 60.

set ringtype X

30

AG-168VSIP GATEWAY User Manual (V1.42)

Set types of ring. X is ranged from 0 tohrough 12: 0-9:ring as ordinary rings

in different frequency; 10: do not ring; 11: ring as music shipped from factory;

12: ring as music saved by user

set digitmap X

Set whether to use digitmap. X ranged from 0 to 1: 0: do not use digitmap; 1:

use digitmap.

set fwdnumber XXXXXXX

Set receiving forwarded calls GATEWAY number. XXXX must be an Arabic

numeral and no longer than 16 characters

set fwdpoweroff X

Enable/disable forward calls if power off. X is ranged from 0 through 1. 0: do

not forward calls if power off; 1: forward call if power off.

set fwdalways X

Enable/disable forward all calls. X is ranged from 0 through 1. 0: do not

forward all calls; 1: forward all calls.

set fwdbusy X

Enable/disable forward calls if busy. X is ranged from 0 through 1. 0: do not

forward calls if busy; 1: forward call if busy.

set fwdnoanswer X

Enable/disable forward calls without replying. X is ranged from 0 through 1. 0:

do not forward calls without replying; 1: forward call without replying.

set audioframes X

31

AG-168VSIP GATEWAY User Manual (V1.42)

Set audio frames in RTP package. X is Arabic numerals between 0 and 7.

set 6.3k X

With G.7231, set AG-168VIP GATEWAY to use 6.3K rate or not. X is

ranged from 0 through 1: 0: use 6.3K rate; 1: use 5.3K rate.

set vad X

Enable/disable VAD. X is ranged from 0 through 1: 0: disable VAD; 1: enable

VAD.

set agc X

Enable/disable AGC. X is ranged from 0 through 1: 0: disable AGC; 1: enable

AGC.

set aec X

Enable/disable AEC. X is ranged from 0 through 1: 0: disable AEC; 1: disable

AEC.

set handsetin X

Set initial volume of handset. X is ranged from 0 through 15.

set speakerin X

Set initial volume of microGATEWAY of the base. X is ranged from 0 through

15.

set handsetout X

Set initial volume of handout. X is ranged from 0 through 31.

set codec1 X

Set the priority 1of the audio compression algorithm. X is range from 0

32

AG-168VSIP GATEWAY User Manual (V1.42)

through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.

set codec2 X

Set the priority 2 of the audio compression algorithm. X is range from 0

through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.

set codec3 X

Set the priority 3 of the audio compression algorithm. X is range from 0

through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.

set codec4 X

Set the priority 4of the audio compression algorithm. X is range from 0

through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.

set codec5 X

Set the priority 5 of the audio compression algorithm. X is range from 0

through 4: 0: g729; 1:g7231; 2: g711u; 3: g711a; 4: gsm.

set password XXXX

Set password of the AG-168VIP GATEWAY. XXX must be ASCII

characters.

set superpassword XXXX

Set super password of the AG-168VIP GATEWAY. XXX must be ASCII

characters.

set debug X

Set open debugging message output grade for special tool. X is ranged from 0 through 5: 0: close debugging output; 1: output the operation information to the window; 2: output all the bug information and data in test window; 3: save the bug information into SDRAM; 4: disable checks the mark.

33

AG-168VSIP GATEWAY User Manual (V1.42)

set upgradeaddr XXX.XXX.XXX.XXX

Set IP address or domain name of FTP server supplying upgraded program of AG-168VIP GATEWAY.

set ntsip XXX.XXX.XXX.XXX

Set IP address of time server.

set daylight X

Set use daylight or not. X ranged from 0 through 1: 0: do not use daylight; 1:

use daylight.

set timezone XX

Set time zone.

Command store

Syntax description: no keyword. Parameter ranged from 0 through 4.

Usage: Save the current settings to the designated position.

Relevant Usage: store 1

Command load

Syntax description: no keyword. Parameter ranged from 0 through 4.

Usage: Load the designated settings to the current position.

Relevant Usage: load 1

Command exit

Syntax description: no keyword and parameter

Usage: Exit from Telnet command window without saving the configuration.

Relevant usage: None

Command write

34

AG-168VSIP GATEWAY User Manual (V1.42)

Syntax description: No keyword and parameter

Usage: Save the configuration and restart theAG-168VIP GATEWAY.

Command ping

Syntax description: ping IP address

Usage: ping IP address of other NAT device

Relevant usage: In telnet window, input ping xx.xxx.xx.xx an IP address and return, then the result will be displayed. If the address is effective, “ping OK” will be seen; if the address is ineffective, nothing will be seen. Fox example:

P:\>ping 203.93.9.57

P:\>

ping OK

P:\>ping 27.56.120.56

P:\>

Note Usually, the echo time of ping command is no more than 1 second. So if the result is not displayed in 5 seconds, ping command is fail.

ftp command

Syntax description: ftp value

Usage: the system connects to the FTP server auto to get the corresponding file and deal with it.

Relevant usage: ftp X

X ranged from 0 through 2:

X-0:Connect to FTP Server to get the file of updating program and save it to the SDRAM of the GATEWAY. Then the file can be read by PalmTool. This operation aims at testing.

X-1:Connect to FTP Server to get the file of updating program and update program Flash. This operation aims at updating program.

X-2:Connect to FTP Server to get the file of updating dial rules and update program Flash. This operation aims at updating dial rule.

Note When you use ftp 0 and ftp 1 commands, if the file get from FTP server is too large or the net speed is too slow, then the process will not be seen in telnetwindow. Please be patient. Using ftp command in telnet to get file spends almost same minutes as getting file using GATEWAY. So if nothing is displayed after too long time, it means that ftp is fail.

35

AG-168VSIP GATEWAY User Manual (V1.42)

Note All the Telnet commands ofAG-168VIP GATEWAY should be written in low case and the password is case sensitive.

The usage of AG-168VFXS

Receving calls

No matter what calls from IP or PSTN , the phone connecting to AG-168VFXS port will ring . Mention you that there is call. You can pick up the handset or the speaker of the normal phone.

Call when Dual mode disabled

Call with phone number:

1 Dial with handset: pickup the handset, dial after dial tone

2 Dial with speaker: press speaker, dial after dial tone

3. Redial: press redial and call the last number

Call with ip address:

If not registered in gatekeeper and gateway disabled, dial with the ip address:

1.pickup the handset, call after dial tone, press # after numbers

2.Press speaker, input ip address after dial tone, press # after numbers

Notice: Dial with ip address, using * for .

Call with GATEWAY

If registered in Gatekeeper dial the number.

Pick up the handset or Press speaker, dial the number after the dial tone

36

AG-168VSIP GATEWAY User Manual (V1.42)

and then press .

Call when PSTN first Dual mode enabled

Call PSTN number

When PSTN first setted, the way of dial is the same as normal PSTN phone.

Call voip number

Press the cradle or the flash key of the normal phone, enable AG-168to be in voip

state from pstn first mode. Dial after the dial tone. Refer to “Call when Dual mode

disabled” chaptor

Call when IP first Dual mode enabled

Dial voip phone

When ip first was setted , pick up the phone and dial as “Call when Dual mode

disabled”chaptor

Call PSTN phone

Predial the prefix number in the “dual mode prefix”, AG-168Vwill change to

PSTN line, call after the dial tone.

Emergency Call

When AG-168Vis power off or in falure, the Normal phone would connect with the PSTN LINE, work as the “LIFELINE” and call emergency number.

37

AG-168VSIP GATEWAY User Manual (V1.42)

Upgrade AG-168VIP GATEWAY

Telnet command to updating

Using telnet , connecting AG-168VFXS, input SuperPassword when registered. Inputftp X command to update, the value range is0-2 .detailed meaning is :

x-0connecting to FTP server, getting the file to updating , and save in the sdram of the phone. Read from palmtool in order to debug.

x-1connecting to FTP server, getting the file to updating and refresh the firmwarex-2connecting to FTP server , getting the file for the dial rule and refresh.

Using HTTP

Using HTTP, connecting AG-168VFXS gateway , input SuperPassword when

registered.

 

 

Press

,

promt the page. Detailed operation refer to

“updating and dial rule chaptor”

of

“configuration through webpage”

updating through Palmtool

Download the palmtool from www.atcom.com.cn, run the tool and set the ip address on

“IP ADDRESS ” , press the button of “phone settings” , change the “debug” to be “no

check” and save. After rebooting , press the button of “updating ” to get the newest

firmware to updating.

Prepare Updated program through FTP

You can ask the server provider for the latest version of program.

Operation

1.The service provider must have an FTP server. This server should allow anonymous

38

AG-168VSIP GATEWAY User Manual (V1.42)

logins.

2. The service provider needs to upload these files to the FTP server:

HardwareTag_ServiceType_Protocol_XXX.bin

This file contains the phone’s firmware binary

HardwareTag_ServiceType_Protocol_cfgXXX.dat

This file contains the phone’s configuration settings

HardwareTag_ServiceType_Protocol_mapXXX.txt

This file contains the phone’s digit map configuration

In the files above HardwareTag is phone’s hardware type, and is identical to the string in the second line of the LCD display.ServiceType corresponds with the “servicetype” field in the phone’s settings page.Protocol is the communications protocol which the IP phone uses.XXX is the version number of the files.

For example if you support the PA168S phone, the “servicetype” is “citron”, the firmware version is 1.35 and the phone settings and digit map version are both 1.32 then the files on your FTP server should be named as:

PA168S_citron_h323_135.bin

PA168S_citron_h323_cfg132.dat

PA168S_citron_h323_map132.txt

Important: The version number in the file name don’t include the sub version number. For example, if the version is 1.40.007, then in file name, you should write 140 only.

If the service provider doesn’t need to upgrade the digit map, it can be omitted from the FTP server. This will not affect the ability to upgrade phones over the network.

3. All the terminals in the system will do the upgrade if you use the upgrade method in item 2. But in fact, some customers want to upgrade a special terminal only. So this way could not fit for this request. We do some modification based on the way in item 2 to provide more way to do the FTP upgrade.

In phone settings, there is a parameter “upgrade type”, the possible value for this

39

AG-168VSIP GATEWAY User Manual (V1.42)

parameter is "disable", "all", "mac", "pppid", "account", "phonenumber". When select as "disable" the terminal will NOT do the auto upgrade when select as "all" then the terminal will do the upgrade as item 2 when select as other value it will add more check based on item 2’s rule. The detail rules are:

Mac

PA168S_citron_h323_00-09-45-00-00-00_135.bin

 

 

Ppp id

PA168S_citron_h323_pppid_135.bin

 

 

Account

PA168S_citron_h323_account_135.bin

 

 

Phonenumb

PA168S_citron_h323_phonenumber_135.bin

er

 

 

 

The red character is the content for the terminal to check. The configuration settings and digit map file have same rules. By this way, we could upgrade a special terminal by FTP.

When upgrade the configuration file, if you select upgradetype as “all”, then the terminal will keep the network settings, account, pin, servicetype without changing; but if you select other upgradetype, then the terminal will only keep network settings and the parameter related with upgradetype without changing. Other settings will all be rewrite as the configuration file. For example, if you select upgradetype as “account”, then the terminal will keep network settings and account without changing. All other settings, like phone number, pin, service type, will changed as the configuration file.

4. Customers must begin with firmware version 1.34 or later. First set the “upgrade addr” field as the FTP service address(domain name or ip address are all OK) , and ensure that the “servicetype” is same as the service provider requested. After the phone is rebooted, it will connect to the FTP server automatically. It will then check the filenames for type and version. If it finds the matching file with a later version than that which is installed then it will perform an upgrade. If all three files have a new version, the phone will upgrade in the following order: phone setting first, then digit map after rebooting, and then firmware binary after rebooting again. If the server version is not newer than current version in the phone, no upgrade is performed. This guarantees that customers have the latest firmware installed at all times..

Since it may take about ten minutes to upgrade some kinds of firmware binaries, we need customers to verify that they want to upgrade at this time. The phone will display “Sure to Upgrade” on the LCD to prompt customers before it does the upgrade.The customers can use the “Handfree” key to confirm it.

For the service provider, this system gives the flexibility to decide whether the latest version contains changes worth supporting. For example if the current firmware is 1.34

40

AG-168VSIP GATEWAY User Manual (V1.42)

and there are no new features of use to them in our 1.35 and 1.36 versions, then they don’t need to put these files on FTP server. The customers will continue to use version 1.34. However if we have some useful features in 1.37, then by uploading the new files to the FTP server all customers will be upgraded at their next system reboot.

4. We also support manual FTP upgrades via the keypad on phones. If the service provider decides to use this feature, the following files also need to be uploaded:

HardwareTag.bin

firmware binary

HardwareTag.dat

phone settings

HardwareTag.txt

digit map

Here HardwareTag is phone’s hardware type, as in item 2 above.

A manual firmware upgrade is performed by picking up the phone and pressing

Phone Password (default: 1234) + n + LocalIP_Key

If n = 5, the phone settings are upgraded

If n = 6, the digit map is upgraded

If n = 8, the firmware is upgraded

Reserves the right to make changes in technical and product

specification without prior notice.

AG-168V SIP GATEWAY User Manual(V1.42)

All rights reserved

41