GarrettCom S14 User Manual

4 (1)
GarrettCom S14 User Manual

Magnum S14 Convenient Switch

(A member of Converter Switch family)

Installation and User Guide

www . GarrettCom . com

S14 Convenient Switch

Installation and User Guide (09/04)

MagnumS14 Convenient Switch

Installation and User Guide

Part #: 84-00100 Rev. A (06/04)

Trademarks

GarrettCom, Magnum, Link-Loss-Learn, S-Ring, Convenient Switch and Converter Switch are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc. Ethernet is a trademark of Xerox Corporation

NEBS is a registered trademark of Telcordia Technologies UL is a registered trademark of Underwriters Laboratories

Important: The Magnum S14, 10/100 Mb/s Convenient Switch contains no user serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. If problems are experienced with Magnum S14, 10/100 Mb/s Switches products, consult Section 5, Troubleshooting, of this User Guide.

Copyright © 2004 GarrettCom, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from GarrettCom, Inc.

Printed in the United States of America.

www . GarrettCom . com

i

S14 Convenient Switch

Installation and User Guide (09/04)

Federal Communications Commission

Radio Frequency Interference Statement

This equipment generates, uses and can radiate frequency energy and if not installed and used properly, that is in strict accordance with the manufacturer's instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

www . GarrettCom . com

ii

S14 Convenient Switch

Installation and User Guide (09/04)

Contacting GarrettCom, Inc

Please use the mailing address, phone and fax numbers and email address listed below:

GarrettCom, Inc.

47823 Westinghouse Drive Fremont, CA 94539

Phone (510) 438-9071

Fax (510) 438-9072

Website: http://www.GarrettCom.com

Email: support@garrettcom.com

www . GarrettCom . com

iii

S14 Convenient Switch

Installation and User Guide (09/04)

TABLE OF CONTENTS

 

Page

1.0

SPECIFICATIONS ...............................................................................

 

1

1.1

Technical Specifications .....................................................................

 

1

2.0

INTRODUCTION ...............................................................................

 

10

2.1

Inspecting the Package and the Product.............................................

10

2.2

Product Description ...........................................................................

 

11

2.3

Magnum S14-Series, with four (RJ-45) Copper ports .......................

16

2.4

Frame Buffering and Latency ............................................................

 

17

2.5

Features and Benefits.........................................................................

 

20

2.6

Applications for office S14-Series.....................................................

 

22

3.0

INSTALLATION.................................................................................

 

29

3.1

Locating the Convenient Switch Unit................................................

29

3.2

MC14-TRAY for Rack Mounting of S14-Series Switches...............

30

3.3

MC14-TR+PS9 & MC14-TR+PS9X2..................................................

31

3.4

DIN-Rail mounting option.................................................................

 

33

3.5Power Requirements, Power Supply Types for S14-Series Switches 34

3.6 Powering the S14H & S14P (DC internal) with 12V, 24V or –48 ........

36

www . GarrettCom . com

iv

S14 Convenient Switch

Installation and User Guide (09/04)

3.7

S14H, DC-powered, -48VDC, 24VDC and 9VDC Installation .......

38

3.8

Connecting Twisted Pair (RJ-45 ports)..............................................

40

3.8.1

Connecting Twisted Pair (RJ-45, CAT 3 or CAT 5) ................

41

3.8.2

Connections to NICs which support Auto-Negotiation .............

42

4.0

OPERATION .......................................................................................

 

42

4.1

Dual-Speed Functionality, and Switching .........................................

42

4.2

Auto-cross (MDIX),Auto-negotiation and Speed-sensing.................

45

4.3

Dual LEDs, Front-panel and side-panel (Magnum S14-Series) ......

46

5.0

TROUBLESHOOTING ......................................................................

 

47

5.1

Before Calling for Assistance ............................................................

 

48

5.2

When Calling for Assistance .............................................................

 

49

5.3

Return Material Authorization (RMA) Procedure .............................

50

5.4

Shipping and Packaging Information.................................................

51

APPENDIX A: WARRANTY INFORMATION.........................................

53

www . GarrettCom . com

v

S14 Convenient Switch

Installation and User Guide (09/04)

Revisions

10/04: Small edit and updates on power supply option. 09/04: Small edit and updates on UL.

06/04: Small revision of the Agency Approvals

Rev A 03/04: Initial release of this user manual for the S14 Converter Switch

GarrettCom, Inc. reserves the right to change specifications, performance characteristics and/or model offerings without notice.

www . GarrettCom . com

vi

S14 Convenient Switches

Installation and User Guide (09/04)

1.0SPECIFICATIONS

1.1Technical Specifications

Ports Performance

When a port is operating at 100Mbps: Data Rate: 100Mbps

When a port is operating at 10 Mbps: Data Rate: 10 Mbps

Network Standards

100Mb: Ethernet IEEE 802.3u, 100BASE-TX, 100BASE-FX 10 Mb: Ethernet IEEE 802.3, 10BASE-T

Auto-sensing for speed: IEEE 802.3u

Packet-Processing Between Domains

Filter / Forwarding Rate from 100Mbps ports: 148,800 pps max Filtering and Forwarding Rate from 10 Mbps ports: 14,880 pps max. Processing type: Store and Forward, non-blocking

Auto-learning: 2K address table

www . GarrettCom . com

1

S14 Convenient Switches Installation and User Guide (09/04)

Address buffer age-out time: 300 sec.

Packet buffers memory: 128KB,dynamically shared on all domains

Latency (not including packet time):

100 to 10 Mbps:

5µs

Path Delay Value: 50 BT on all ports

10 to 100Mbps:

5µs

 

 

Maximum Ethernet Segment (or Domain) Lengths

 

10BASE-T (Unshielded twisted pair)

- 100 m (328 ft)

 

100BASE-TX (CAT 5 UTP)

 

- 100 m (328 ft)

 

Operating Environment

 

 

 

Ambient Temperature (S14):

32ºF to 104ºF (0ºC to 40ºC)

(S14H):

-13ºF to 140ºF (-25ºC to 60ºC)

Long term per independent agency tests (UL) -40ºF to 149ºF (-40ºC to 85ºC) Short term per IEC Type tests

(S14P): -40ºF to 167ºF (-40ºC to 75ºC) Long term per independent agency tests (UL)

www . GarrettCom . com

2

S14 Convenient Switches

Installation and User Guide (09/04)

 

-58ºF to 212ºF (-50ºC to 100ºC)

 

Short term per IEC Type tests

Storage Temperature, All models:

-40ºF to 160ºF (-40ºC to 85ºC)

Cold Start:

(S14H) model to -20ºC

 

(S14P) model to -40ºC

Ambient Relative Humidity:

5% to 95% (non-condensing)

Altitude (All models):

-200 to 5000ft. (-60 – 15,000 m)

Conformal Coating (optional)

Humidity protection

Note: H and P models are designed for NEBS compliance, including, vibration, shock and altitude.

Packaging:

Enclosure: Rugged sheet metal (Steel). Dimensions, Switch unit: Height x Width x Depth

S14, S14H, and S14P: 3.5 in H x 3.0 in W x 1.0 in D (8.9 cm x 7.6 cm x 2.5 cm)

Weight: all models: 4.6 oz. (130g); power supply, –d, and i: 5.9 oz (170g)

www . GarrettCom . com

3

S14 Convenient Switches

Installation and User Guide (09/04)

–Hd, and Hi: 5.8 oz (165g)

–Pd, and =Pi:

7.9 oz (225g)

Cooling Method: Convection on regular model, plus the case is used as a heat sink on “H” and “P” models.

POWER SUPPLY

These products are intended to be supplied by a Listed, Direct Plug-In power unit, marked “Class 2”, or a Listed ITE Power Supply, marked “LPS”, which has suitably rated output voltage (i.e. 9vdc, 12vdc, 24vdc, 48vdc), and suitably rated output current (i.e. 100mA to 500mA).When connected to a 48 V centralized dc source these products shall be provided with a Listed 5 A DC fuse in the supply circuit.

UL listed class II Power Supply, ( AC External):

Power input (8-15)V DC, jack is 2.5mm center +ve , with 6ft. cord

www . GarrettCom . com

4

S14 Convenient Switches

Installation and User Guide (09/04)

Input: 120vac at 60 Hz for “d” models, 240vac at 50Hz for “i” models that have IEC320 power connector built-in the PS unit. Out put12vdc, 1 Amps

Input: 100-240V AC at 47-63Hz, for “-Hd” high temp., 100-240V AC at 47-63Hz “-for Hi” models that have IEC320 power connector built-in the PS unit.

Out put12vdc, 1.25 Amps

Input: 100-240V AC at 47-63Hz, for “-Pd” high temp. 100-240V AC at 47-63Hz, “-Pi” models that have IEC320 power connector built-in the PS unit.

Out put12vdc, 2 Amps

DC to unit: 12V DC, 2.5mm jack, center +ve, 6ft. cord

Power Supply ( Direct DC ): built-in screw terminal block for +, -, ground. The 12V DC jack is also present.

12V DC internal (range of 8.0 to 15V DC),

24V DC internal (range of 18 to 36V DC)

www . GarrettCom . com

5

S14 Convenient Switches

Installation and User Guide (09/04)

-48V DC internal (range of 36 to 60V DC) t.

Power Consumption: 3 watts typical, 4 watts max. Note 1: 8-15V DC can be used for dual source DC input

Note 2: Internal DC power floats, user may ground “+” or “-” if desired.

Port Connectors:

RJ-45 Port: Auto-cross(MDIX), 100BASE-TX and 10BASE-T:shielded 8-pin female. Three RJ-45 ports provided in front, and one on the rear. Supports shielded (STP) and unshielded (UTP) Cat 3, 4, 5 cable. For POE pass-through option on H and P models, request quote.

LED Indicators (Dualfront and end, port #4 has front only)

POWER: Steady On when power applied 10/100: = 100Mbps; OFF = 10 Mbps

LK/ACT: Steady On for LINK with no traffic, blinking indicates port is transmitting / receiving.

F/H: ON = full-duplex, OFF = half-duplex

www . GarrettCom . com

6

S14 Convenient Switches

Installation and User Guide (09/04)

Mounting option for S14 Family of Switches:

Metal Mounting clips for panel mounting : included

DIN-Rail mounting option: Model # DIN-RAIL MC2 (see Section 3.4)

Rack-mount option: MC14-TRAY, see http://www.garrettcom.com/mc_tray.htm

Mean Tine Between Failure (MTBF) – 15+ years, Telcordia (Bellcore) Method

Agency Approvals and Standard Compliance:

UL Listed (UL 60950), cUL, CE, Emissions meet FCC Part 15, Class A. NEBS L3 and ETSI compliant

H & P models: IEEE P1613 Env. Std for Electric Power Substations P model: NEMA TS-2 and TEES for traffic control equipment

P model: designed for UL 2043 above-the-ceiling installation

IEC61850 EMC and Operating Conditions Class C for Power Substations

www . GarrettCom . com

7

S14 Convenient Switches

Installation and User Guide (09/04)

Warranty: Three years, return to factory

Made in USA

www . GarrettCom . com

8

S14 Convenient Switches

Installation and User Guide (09/04)

1.2Summary of models and descriptions:

S14-d,i = four 10/100 RJ-45 ports Switch, for office and wiring closet env., ext. AC Pwr Supply S14H-Hd, Hi = Hardened, four 10/100 RJ-45 ports Switch, Factory floor, Int. 8-15VDC,

Ext. AC Hardened power supply included .

S14H-12VDC = Same as S14H model, except Ext. AC Hardened power supply not included S14H-24VDC = Same as S14H-12VDC model, except for 24VDC power input S14HR-24VDC = Same as S14H-24VDC model, but includes DIN-RAIL-MC2 option. S14H-48VDC = Same as S14H-24VDC model, except for -48VDC power input.

S14P-Pd, Pi = ,Premium rated, four 10/100 RJ-45 ports Switch, for un-controlled(outdoor) env. Int. 8 to 15V terminal block, Ext. AC Premium-rated Power Supply included.

S14P-12VDC = Same as S14P-Pd, Pi, except ext. AC Premium Power Supply is not included. S14P-24VDC = Same as S14P-12VDC model, except Ext. AC Premium power supply not included S14PR-24VDC = Same as S14P-24VDC model, but includes DIN-RAIL-MC2 option. S14P-48VDC = Same as S14P-24VDC model, except for -48VDC input

MC14-TRAY = 19” Rack-mount tray for 14-series Switch models, up to 16 units

DIN-RAIL-MC2 = Metal DIN-Rail mounting bracket for one S14-Series Switch

www . GarrettCom . com

9

S14 Convenient Switches

Installation and User Guide (09/04)

2.0INTRODUCTION

This section describes S14-Series models, including appearance, features and typical applications.

2.1 Inspecting the Package and the Product

Examine the shipping container for obvious damage prior to installing this product; notify the carrier immediately of any damage which you believe occurred during shipment or delivery. Inspect the contents of this package for any signs of damage and ensure that the items listed below are included.

This package should contain:

1

Magnum S14-Series Convenient Switch Unit

 

1

External Power Supply, (for S14, S14H, S14P), (d, i model only)

1 set

Metal panel mounting clips and screws, 2 each

 

1

User Guide, i.e., this manual

(continued next page)

www . GarrettCom . com

10

S14 Convenient Switches

Installation and User Guide (09/04)

Remove the Magnum S14-Series Switch from the shipping container. Be sure to keep the shipping container should you need to ship the unit at a later date.

In the event there are items missing or damaged contact your supplier. If you need to return the unit use the original shipping container. Refer to Section 5 Troubleshooting, for specific return procedures.

2.2 Product Description

The Magnum S14 family of Convenient Switches covers the full range of application environments, with regular (office), Hardened (factory floor), and Premiumrated (outdoor) versions. Extra features for heavy-duty and extended temperature operation ranges are included selectively in the Hardened factory-floor and Premium-rated outdoor models. Input power may be AC, or DC at 12V, 24V or –48V, providing a selection for office or for heavy duty industrial applications. This selection of models offers the best price / value unit for each user and installation.

For any user who needs a small chunk of Ethernet connectivity, a 4-port “go anywhere” Magnum S14 Switch is a versatile and handy solution, and can provide it in a convenient compact package.

www . GarrettCom . com

11

Loading...
+ 42 hidden pages