Page 1
INSTALLATION INSTRUCTIONS
Product Revision
7160-0527
Base, Ram Promaster 2014+ -No Drill
(with bucket seats only)
Rev.A
Printing Spec:
Form
INST-617
PS-001
•You must read and follow all of these installation instructions. Failure to follow the installation
instructions may result in serious bodily injury or death
•DO NOT install or use this assembly in the area in which the airbag on the vehicle may be
deployed. The installer and user of this assembly are responsible for installing and using this
assembly outside the area in which an airbag may be deployed. (See Product Mounting
Disclaimer Below)
•Keep these installation instructions with the product and readily available in the vehicle
for future reference of other users of the product.
•Additional copies of the installation instruction can be obtained from Gamber-Johnson.
If you need assistance or have any questions, go to www.gamberjohnson.com or
call Gamber-Johnson at 1-800-456-6868.
•DO NOT remove the warning label form product under any circumstances.
Product Mounting Disclaimer
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© Copyright 2013 Gamber-Johnson, LLC
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Page 2
Install Vehicle Base:
Remove the front two bolts of the front passenger seat using T-40 bit. See Figure 1.1.
Lossen the rear seat bolts of the front passenger seat using T-40 bit. See Figure 2. 2.
Slide the base between the seat rail and seat base. See Figure 3.3.
4.
5.
Replace the front bolts and tighten them.
Retighten the rear bolts.
NOTES:
This vehicle base works only with the bucket seats model.1.
Figure 1.
Figure 2.
Figure 3.
•This assembly should not be positioned in the area where the airbag may be deployed.
•DO NOT position the equipment in front of an airbag. Equipment positioned in front of an
airbag may cause serious injury or death if an airbag is activated.
•If installation of the equipment requires that the equipment be placed in front of an airbag,
the airbag should be deactivated. In order to secure permission for deactivating the airbag
you must contact the National Highway Traffic Safety Administration at 1-800-424-9393 to
gain permission to do so. If you have any questions or need assistance, call Gamber-Johnson
at 1-800-456-6868.
•High speed vehicle turns may cause parts of the assembly to swivel, interfering with the
driver or other equipment.
Loading...