POWERPLANT
AMPLIFIER MANUAL
PP-AM300010 PP-AM200010 PP-AM100010
PP-AM120040 PP-AM60020
CONTENTS |
|
|
• |
AMPLIFIER SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
pg 4 |
• |
AMPLIFIER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
pg 5 |
• |
FOUR CHANNEL AMPLIFIER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
pg 6 |
• |
TWO CHANNEL AMPLIFIER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
pg 8 |
• |
MONOBLOCK AMPLIFIERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
pg 10 |
• |
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
pg 12 |
RECORD YOUR PRODUCT DETAILS HERE:
MODEL NUMBER |
|
DATE OF PURCHASE |
AFFIX RECEIPT HERE
Version 1.0
2 |
3 |
AMPLIFIER SPECIFICATIONS
|
PP-AM300010 (Monoblock) |
PP-AM200010 (Monoblock) |
Class |
D-Class |
D-Class |
|
|
|
Max Power Rating |
3000 Watts |
2000 Watts |
Frequency Response |
20Hz - 320kHz |
20Hz - 320kHz |
|
|
|
Dimensions (mm) |
436(L) x 278(W) x 60(H) |
436(L) x 278(W) x 60(H) |
|
|
|
Power Ratings |
850 Watts RMS per Channel |
600 Watts RMS x 1 Channel |
|
@ 4 Ohms 1% THD+N |
@ 4 Ohms 1% THD+N |
|
1300 Watts RMS per Channel |
900 Watts RMS x 1 Channel |
|
@ 2 Ohms 1% THD+N |
@ 2 Ohms 1% THD+N |
|
1500 Watts RMS x 1 Channel |
1000 Watts RMS x 1 Channel |
|
@ 1 Ohms 1% THD+N |
@ 1 Ohms 1% THD+N |
|
|
|
|
PP-AM100010 (Monoblock) |
PP-AM120040 (4 Channel) |
Class |
D-Class |
Class AB |
|
|
|
Max Power Rating |
1000 Watts |
1200 Watts |
|
|
|
Frequency Response |
20Hz - 320kHz |
10Hz - 100kHz |
Dimensions (mm) |
386(L) x 278(W) x 60(H) |
546(L) x 278(W) x 60(H) |
|
|
|
Power Ratings |
400 Watts RMS x 1 Channel |
125 Watts RMS per Channel |
|
@ 4 Ohms 1% THD+N |
@ 4 Ohms 1% THD+N |
|
620 Watts RMS x 1 Channel |
165 Watts RMS per Channel |
|
@ 2 Ohms 1% THD+N |
@ 2 Ohms 1% THD+N |
|
|
330 Watts RMS Bridged Channels |
|
|
@ 4 Ohms 1% THD+N |
|
|
|
|
PP-AM60020 (2 Channel) |
Class |
Class AB |
|
|
Max Power Rating |
600 Watts |
|
|
Frequency Response |
10Hz - 100kHz |
|
|
Dimensions (mm) |
436(L) x 278(W) x 60(H) |
|
|
Power Ratings |
125 Watts RMS per Channel |
|
@ 4 Ohms 1% THD+N |
|
190 Watts RMS per Channel |
|
@ 2 Ohms 1% THD+N |
|
390 Watts RMS Bridged Channels |
|
@ 4 Ohms 1% THD+N |
|
|
4
ACCEPTABLE AMPLIFIER LOADS
Model |
4 Ohm |
2 Ohm |
1 Ohm |
|
|
|
|
PP-AM120040 |
YES*1 |
YES*2 |
NO |
PP-AM60020 |
YES*1 |
YES *2 |
NO |
PP-AM300010 |
YES |
YES |
YES |
|
|
|
|
PP-AM200010 |
YES |
YES |
YES |
|
|
|
|
PP-AM100010 |
YES |
YES |
NO |
|
|
|
|
*1 Per Channel and Bridged Channel(s), *2 Per Channel ONLY
NB : PP-AM100010 IS NOT 1 Ohm STABLE
AMPLIFIER INSTALLATION
INSTALLATION WARNING
1.Ensure the 12V lead is disconnected from the battery before you connect any new equipment.
2.Ensure the mounting location will not interfere with the gas tank, brake lines or electrical wiring.
3.Ensure the Amplifier is securely fastened to the vehicle to prevent damage in the event of an accident.
4.Ensure all wiring is protected to avoid pinching or crushing which could result in damage to the audio system.
5.Ensure the mounting location has sufficient air flow around the amplifier. If the amplifier is mounted in an enclosed space a 3” fan with ducting should be used to aid in air flow.
6.Do not mount any amplifier on a subwoofer enclosure as extended exposure to vibration may cause malfunction of the amplifier.
7.Ensure you use the recommended gauge wire/cable for all amplifier connections.
Wiring
Ensure the audio system is turned off before making any connections to the amplifier, speakers or source unit. Failure to do so could result in permanent damage to the audio system.
When wiring the FUSION amplifier ensure that the cable is protected from sharp objects and always use rubber grommets when wiring through metal panels. Ensure all terminals and connections are protected from the vehicle chassis and from each other as failure to do so could result in permanent damage to the audio system.
5