FUNAI SST4192, SST4192, SST4132 User Manual

436.14 Kb
Loading...

SYLVANIA

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or workmanship as follows:

DURATION:

PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to any the product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.

THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS WILL BE CHARGED.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE.

To locate your nearest SYLVANIA Authorized Service Center or general service procedure, please call 1-800-968-3429 or write to the following:

 

FUNAI CORPORATION

 

Customer Service

 

100 North Street; Teterboro, NJ 07608

 

Tel :1-800-968-3429

 

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

 

 

 

 

0EMN01876

Printed in Malaysia

 

L6003UD / L6117UT * * * * *

Owner’s

COLOR TELEVISION

Manual

SST4132 (13 inch)

 

SST4192 (19 inch)

FEATURES

Tinted, Bright Black Matrix Picture Tube

181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.

PLL Frequency Synthesized Tuning- The latest PLL frequency synthesized electronic tuning system provides free and easy channel selection, and lets you tune directly to any channel using the channel number buttons (0~9 and +100-key) on the remote control.

On-Screen Function Display.

Full-Function Remote Control

Sleep Timer

Closed Caption Decoder- You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or text display added to the program.

Auto Shut Off Function- If there is no air signal input from the antenna terminal and no operation for 15 minutes, the TV will turn itself off automatically.

V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.

PRECAUTION

Place your TV in a room with adequate ventilation.

Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.

Do not place your TV on soft surfaces, such as rugs or blankets.

Leave enough room for air to circulate around the bottom, top and back of the set.

The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.

Date of Purchase

Dealer Phone No.

Dealer Purchase from

Model No.

Dealer Address

Serial No.

This Owner’s Manual is made of recycled paper.

IF YOU NEED ADDITIONAL ASSISTANCE FOR SET-UP OR OPERATING AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-968-3429.

ANTENNA/CABLE CONNECTIONS

 

UHF/VHF Rod

Before plugging the UHF/VHF Rod

Antenna

(Supplied with

Antenna into the ANT(enna). IN jack, check

13” model only)

that the pin is not bent. If it is bent, straight-

en the pin as illustrated, then plug the pin

VHF

Antenna

into the ANT(enna). IN jack. (Rod antenna

(Not supplied)

is supplied with 13” model only.)

UHF

 

 

 

 

 

 

Antenna

 

Bent pin

 

(Not supplied)

 

 

 

Cable

Plug

 

 

 

 

 

(Needs to be straightened)

(Straight pin)

ANT. IN

 

 

 

 

 

 

OR

 

 

 

VHF/UHF Combiner

 

 

 

(Not supplied)

VHF/UHF Combination Antenna (Not supplied)

*Some cable TV systems use scrambled signals and require a special converter to receive these channels. Consult your local cable company.

CATV Box * or Satellite Box (Not supplied)

OUT

IN

From Cable System

 

 

or Satellite Antenna

 

 

75-ohm

 

75-ohm

Coaxial Cable

 

 

 

Coaxial Cable

 

OR

 

From Cable System

 

 

FCC WARNINGThis equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

CLOSED CAPTION

This TV can receive C1 and C2 of Caption and Text.

Caption Mode

(1)Characters can be displayed on the TV screen when the received broadcast signal contains the Caption Signals.

(2)Paint-on mode: Displays input characters on the screen immediately.

Pop-on mode: Once characters are stored in memory, it is displayed all at once.

Roll-up mode: Displays the characters continuously by scrolling (max. 4 lines)

Note: If the CAPTION C1 or C2 is selected but the caption signal is not included, characters will not be displayed.

Notes:

(1)When your TV receives a special effects playback signal (i.e., Search, Slow, Still) from a VCR’s video output channel (CH3 or CH4), your TV may not display the correct caption or text.

(2)Captions and texts may not match the TV voice exactly.

(3)Interference may cause the closed caption system not to function properly.

(4)The caption or text characters will not be displayed while the menu display or function’s display is shown.

(5) If you see this screen :

Text Mode

(1)Displays the text on the screen by scrolling (max. 7 lines)

(2)If the received broadcast signal does not contain the caption or text signal, no change will occur.

If your TV displays a black box on the screen, this means that your TV is set to TEXT mode. To clear screen, select CAPTION C1, C2 or CAPTION [OFF].

OPERATING CONTROLS AND FUNCTIONS
- FRONT PANEL -
S3126A
This manual covers 13" and 19". The operation of the two models are exactly the same except the appearance. 19" model is illustrated in this manual.
PORTABLE CART WARNING
1. Read instructions-All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions-The safety and operating instructions should be retained for future reference.
3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow Instructions-All operating and use instructions should be followed.
5. Cleaning-Unplug TV from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.
6. Attachments-Do not use attachments not recommended by the TV manufacturer as they may cause hazards.
7. Water and Moisture-Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. Accessories-Do not place this TV on an unstable cart, stand, tripod, bracket, or table. The TV may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the TV.
Any mounting of the appliance should follow the manufacturer’s instructions and should use a mounting accessory recommended by the
manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive
force, and uneven surfaces may cause the appliance and cart combi-
nation to overturn.
SYMBOLE D'AVERTISSEMENT POUR
LES COMPOSANTES
APPAREIL ET MEUBLE A ROULETTES
S3126A

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

 

CAUTION

 

THIS SYMBOL INDICATES THAT DAN-

 

 

 

 

GEROUS VOLTAGE CONSTI-TUTING A

 

RISK OF ELECTRIC SHOCK

 

 

 

 

 

RISK OF ELECTRIC SHOCK IS PRE-

 

DO NOT OPEN

 

 

 

 

 

 

SENT WITHIN THIS UNIT.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

 

 

 

 

THIS SYMBOL INDICATES THAT

SHOCK, DO NOT REMOVE COVER (OR BACK) NO

 

 

THERE ARE IMPORTANT OPERATING

USER SERVICEABLE PARTS INSIDE. REFER SER-

 

 

AND MAINTENANCE INSTRUCTIONS

VICING TO QUALIFIED SERVICE PERSONNEL.

 

 

IN THE LITERATURE ACCOMPANY-ING

 

 

 

 

The important note is located on the rear of the cabinet.

THE APPLIANCE.

 

 

 

 

 

IMPORTANT SAFEGUARDS

AMEUBLESCet appareil ne doit être placé que sur un meuble (avec ou sans roulettes) recommandé par

le fabricant. Si vous l’installez sur un meuble à roulettes, déplacez les deux ensembles avec précaution.

Un arrêt brusque, l’utilisation d’une

force excessive et des surfaces irrégulières risquent de déstabiliser l’ensemble et de le renverser.

9. Ventilation-Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the TV on a bed, sofa, rug, or other similar surface. This TV should never be placed near or over a radiator or heat register. This TV should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to .

10. Power Sources-This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TVs intended to operate from battery power, or other sources, refer to the operating instructions.

11. Grounding or Polarization-This TV is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

12. Power-Cord Protection-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

 

ANTENNA

 

LEAD IN

 

WIRE

 

GROUND

 

CLAMP

 

ANTENNA

 

DISCHARGE UNIT

 

(NEC SECTION 810-20)

ELECTRIC

 

SERVICE

 

EQUIPMENT

 

 

GROUNDING CONDUCTORS

 

(NEC SECTION 810-21)

 

GROUND CLAMPS

NEC - NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

 

ELECTRODE SYSTEM

S 2 8 9 8 A

(NEC ART 250, PART H)

receptacles, and the point where they exit from the appliance.

13.Outdoor Antenna grounding-If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

14.Lightning-For added protection for this TV receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power-line surges.

15.Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16.Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV.

18.Servicing-Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19.Damage Requiring Service-Unplug this TV from the

wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power supply cord or plug is damaged or frayed.

b.If liquid has been spilled, or objects have fallen into the TV.

c.If the TV has been exposed to rain or water.

d.If the TV does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to its normal operation.

e.If the TV has been dropped or damaged in any way.

f.When the TV exhibits a distinct change in perfor- mance-this indicates a need for service.

20.Replacement Parts-When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.

21.Safety Check-Upon completion of any service or repairs to this TV, ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition.

22.Heat-This TV product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

VIDEO AUDIO

EARPHONE MENU

VOLUME

CHANNEL

POWER

1 2 3 4 5

- REMOTE CONTROL -

 

 

 

 

14

7

POWER

 

GAME

SLEEP

 

 

 

13

 

 

 

 

DISPLAY

 

1

2

3

12

9

4

5

6

CHANNEL

 

 

 

 

 

 

RETURN

 

7

8

9

11

 

 

0

+100

 

6

CH

 

VOL

VOL

 

5

CH

 

 

MUTE

10

 

 

MENU

4

1.VIDEO (in) jack- Connect to the video output jack of a video camera or VCR.

2.AUDIO (in) jack- Connect to the audio output jack of a video camera or VCR.

3.EARPHONE jack- To connect earphone (not supplied) for personal listening.

6 7 8

4.MENU button- Press to display the menu on the TV screen.

5.VOLUME /buttons- Press to control the volume level.

Press to determine a setting mode from the menu on the TV screen. (only the VOL button)

Press to select or adjust from a particular menu. (for example: Language Selection, Channel Presetting, Closed Caption Selection, Picture Adjustment, V-CHIP Set Up)

6.CHANNEL /buttons- Press to select memorized channel.

NOTE:You MUST PRESET channels BEFORE using CHANNEL /button. (See CHANNEL PRESETTING)

Press to select a setting mode from the menu on the TV screen.

Press to select item you want to adjust in the picture control mode.

7.POWER button- Press to turn the TV ON and OFF.

8.Infrared Sensor Window- Receives the infrared control signals from the remote control unit.

- REAR PANEL -

ANT.IN

16

15

9.CHANNEL NUMBER buttons- Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel.

+100 button- Press to select cable channels which are equal or greater than number

100.

10.MUTE button- Press the MUTE button to turn off the sound portion of the TV program. (Volume level display turns LIGHT RED from LIGHT BLUE.) Press the MUTE button again or press the VOL(ume) or button to restore sound.

11.CHANNEL RETURN button- Press this button to go back to the previously viewed channel. For example, pressing the CHANNEL RETURN button once will change channel display from CH 3 (present channel) to CH 10 (previously viewed channel), and pressing it a second time will return from CH 10 to CH 3.

12.DISPLAY button- Press to display the channel number on the screen. If you press it again, the channel number will disappear.

13.SLEEP button- Press the SLEEP button to display the sleep timer and start the function. The shut off time can be determined by the number of times you press the button. (0, 10, 20, 30,..90, 0 minutes)

14.GAME button- Press to set the Game mode and external input mode at the same time. Press the GAME button again to exit the mode.

15.ANT(enna). IN jack- Connect to an antenna, cable system, or satellite system.

16.AC cord- Connect to a standard AC outlet (120V/60Hz).

NOTE: Remove the AC cord from the hook to avoid breaking a wire before you connect to a standard AC outlet.

INSTALLING THE BATTERIES

1

Slide the battery compartment cover on the remote unit.

2

Insert 2 "AA" penlight batteries into battery compartment in the direction as indicated by the polarity (+ / -) markings. Batteries installed with incorrect polarity may damage the remote unit.

3

Replace the cover.

SLEEP 10
To cancel the sleep timer:
Press the SLEEP button repeatedly until "SLEEP 0" is displayed.
PICTURE CHANNEL SET
[ENGLISH]ESPAÑOL V-CHIP SET UP CAPTION [OFF]
PICTURE CHANNEL SET
[ENGLISH]ESPAÑOL V-CHIP SET UP CAPTION [OFF]
ADD/DELETE
AUTO MEMO

PREPARATION FOR USE

LANGUAGE SELECTION

If you want to change the language of the on-screen menu, follow the procedure below.

1)Connect the power cord to a standard AC outlet.

2)Press the POWER button to turn on the TV.

3)Press the MENU button so that the menu display appears on the TV screen.

4)Press the CH(annel) or button to point to "[ENGLISH]".

5)Select "ENGLISH" or "ESPAÑOL" = Spanish by using the VOL(ume) or button.

6)Press the MENU button to exit the menu.

PICTURE CHANNEL SET

[ENGLISH]ESPAÑOL V-CHIP SET UP CAPTION [OFF]

PICTURE CHANNEL SET

[ENGLISH]ESPAÑOL V-CHIP SET UP CAPTION [OFF]

CHANNEL PRESETTING

NOTE:You MUST PRESET channels BEFORE using CHANNEL or button. To preset a channel or to change a preset channel, follow the procedure below.

1) Press the POWER button to turn on the TV.

2) Press the MENU button so that the menu display appears on the TV screen.

3)Press the CH(annel) or button to point to "CHANNEL SET". Then, press the VOL(ume) button.

4)Press the CH(annel) or button to point to "AUTO MEMO".

Then, press the VOL(ume) button.

The tuner scans and memorizes all active channels in your area.

The TV distinguishes between standard TV channels and cable channels.

When AUTO MEMO action is completed, the lowest memorized channel reappears on the screen.

When you press the CH(annel) or button after selecting AUTO MEMO, the tuner will stop at the memorized channels only.

The TV may recognize TV channels to be CATV channels

by the receiving conditions. In this case, try AUTO MEMO action again in the fine receiving conditions.

[ADD/DELETE FUNCTION]

1)Press the MENU button so that the menu display appears on the TV screen.

2)Press the CH(annel) or button to point to "CHANNEL SET". Then, press the VOL(ume) button.

3)Press the VOL(ume) button so that "ADD/DELETE" is selected.

4)Use the CH(annel) or button to select the

channel you wish to put into memory or to erase from memory. Note: The display will return to the screen in about 10 seconds. Perform "ADD/DELETE" function while this display appears on the

screen.

Press the VOL(ume) or button to light up the channel number in LIGHT BLUE if you wish to add the channel into memory.

Press the VOL(ume) or button to light up the channel number

in LIGHT RED if you wish to erase the channel from memory. 5) Press the MENU button to exit the menu.

PICTURE CHANNEL SET

[ENGLISH]ESPAÑOL V-CHIP SET UP CAPTION [OFF]

ADD/DELETE

AUTO MEMO

RESUME FUNCTION

If the power fails or is disconnected while the TV is powered on, the TV will turn on automatically when the power resumes.

OPERATIONS

WATCHING A TV PROGRAM

PICTURE ADJUSTMENT

1)Press the POWER button to turn on the TV.

2)Select the desired channel with the CH(annel) or button.

3)Adjust the volume to the desired listening level using the VOL(ume) or button.

4)Adjust picture controls for a natural looking image. (See "PICTURE ADJUSTMENT".)

SETTING THE SLEEP TIMER

The sleep timer function enables you to shut off the power without pressing the POWER button after a desired time period.

1)Press the POWER button to turn on the TV and press the SLEEP button on the remote control .

2) You may change the sleep time with pressing the SLEEP button on the remote control repeatedly. The timer is set up to 90 minutes, 10 minutes each time the SLEEP button is pushed. (The timer display counts up and sleep timer will be displayed on the screen when you press the SLEEP button on remote control.)

Note: When you disconnect the unit from the AC outlet, or if you have a power failure, the sleep time will be lost.

CLOSED CAPTION SELECTION

You may view specially labeled (cc) TV pro-

1) Press the MENU button so that the menu

grams, movies, news, prerecorded tapes, etc.

 

display appears on the TV screen.

with either a dialogue caption or text display

2) Press the CH(annel) or button to point

added to the program.

 

 

 

 

to "CAPTION".

 

 

 

 

 

3) Press the VOL(ume) or button to select

 

 

 

 

 

the mode you wish.

 

 

 

 

 

4) When done, press the MENU button to exit

: Press the VOL(ume) or button.

 

 

 

the menu.

 

 

 

 

 

 

 

 

 

 

PICTURE

PICTURE

PICTURE

 

 

PICTURE

PICTURE

CHANNEL SET

CHANNEL SET

CHANNEL SET

 

CHANNEL SET

CHANNEL SET

[ENGLISH]ESPAÑOL

[ENGLISH]ESPAÑOL

[ENGLISH]ESPAÑOL

[ENGLISH]ESPAÑOL

[ENGLISH]ESPAÑOL

V-CHIP SET UP

V-CHIP SET UP

V-CHIP SET UP

 

V-CHIP SET UP

V-CHIP SET UP

CAPTION [OFF]

CAPTION [ C1]

CAPTION [ C2]

 

CAPTION [ T1]

CAPTION [ T2]

1)Press the MENU button so that the menu display appears on the TV screen.

2)Press the VOL(ume) button so that "PICTURE" is selected.

3)Select the feature you wish to adjust with the CH(annel) or button and adjust it with the VOL(ume) or button.

GAME MODE

Set to the most suitable position for TV GAME.

[+] : ON

[-] : OFF

BRIGHT

Adjust until the whitest parts of the picture are as bright as you prefer.

[+] : increase brightness [-] : decrease brightness

CONTRAST

Adjust to increase or decrease contrast. [+] : increase contrast

[-] : decrease contrast

COLOR

Adjust to be brilliant or pale color. [+] : be brilliant color

[-] : be pale color

TINT

Adjust to obtain natural skin tones. [+] : greenish tone

[-] : reddish tone

Notes:

“+” is achieved by pressing the VOL(ume)

button and “-” by pressing the VOL(ume) button.

In the above steps, the picture adjustment display will disappear from the TV screen after about 10 seconds unless you press any buttons, even though you may not be finished. Press the MENU and VOL(ume) button so that "PICTURE" is selected. Then, press the CH(annel) or button repeatedly until the display returns to the screen.

If you adjust the other Picture control after you set the Game mode to [ON], the Game mode is set to [OFF] automatically.

[USING THE GAME BUTTON]

You may also set the Game mode and external input mode at the same time by pressing the GAME button on the remote control. “GAME” appears on the TV screen.

To exit the Game mode and external input mode, press the GAME button on the remote control again.

To cancel the Game mode only, adjust the picture control. In this case, “VIDEO” instead of “GAME” appears on the TV screen.

When you press the GAME button if the TV is off, the TV turns on and will be in the Game mode and external input mode automatically.

: Press the CH(annel) or button.

[-]

GAME MODE [+]

[-]

BRIGHT

[+]

[-] CONTRAST [+]

[-]

COLOR

[+]

[-]

TINT

[+]

OFF

ON

 

 

 

 

 

 

 

 

 

 

+ 5 hidden pages