FUNAI RSEF420E User Manual

458.87 Kb
Loading...

LIMITED WARRANTY

FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:

DURATION:

PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. This warranty does not cover any cosmetic parts or complete assembly parts.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This FUNAI Limited warranty does not apply to any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN OR DELIVERED TO A FUNAI AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS., YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP. IN WRITING.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE.

To locate your nearest FUNAI Authorized Service Center or for general service procedure, please call 1-800-968-3429 or write to the following:

FUNAI CORPORATION, INC. Service Center

19900 Van Ness Avenue, Torrance, CA 90501

Tel : 1-800-968-3429

1EMN20058

Printed in Malaysia

 

L2410UL * * * * *

Owner’s

 

SYLVANIA

20 INCH

 

Manual

 

COLOR TELEVISION

RSEF420E

FEATURES

MTS/SAP Tuner

Flat Screen Picture Tube

181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.

PLL Frequency Synthesized Tuning- The latest PLL frequency synthesized electronic tuning system provides free and easy channel selection and lets you tune directly to any channel using the channel number buttons (0~9 and +100-key) on the remote control.

On-Screen Function Display

Full-Function Remote Control

Sleep Timer

Closed Caption Decoder- You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or text display added to the program.

Auto Shut Off Function- If there is no signal input from the antenna terminal and no user operation for 15 minutes, the TV will turn itself off automatically.

V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.

S-VIDEO Input- Allows you to get better picture detail and clarity for the playback of S-VHS VCR tapes or Video Discs.

Front AV Input

Rear Audio Input

PRECAUTIONS

Place your TV in a room with adequate ventilation.

Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.

Do not place your TV on soft surfaces, such as rugs or blankets.

Leave enough room for air to circulate around the bottom, top and back of the set.

The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.

Date of Purchase

 

Dealer Phone No.

 

Dealer Purchase from

 

Model No.

 

Dealer Address

 

Serial No.

 

IF YOU NEED ADDITIONAL ASSISTANCE FOR SET-UP OR OPERATING

AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-968-3429.

ANTENNA/CABLE CONNECTIONS

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

MISE EN GARDE:

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

VHF

Antenna

(Not supplied)

UHF Antenna

(Not supplied)

VHF/UHF Combiner (Not supplied)

VHF/UHF Combination Antenna (Not supplied)

UHF/VHF Rod

*Some cable TV systems use scram-

Antenna

bled signals and require a special con-

(Not supplied)

verter to receive these channels.

 

Consult your local cable company.

CATV Box * or Satellite Box (Not supplied)

OUT IN

75-ohm

Coaxial Cable

ANT. IN

OR OR

From Cable System or Satellite Antenna 75-ohm

Coaxial Cable

From Cable System

FCC WARNINGThis equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 82040 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

CLOSED CAPTION

This TV can receive C1 and C2 Caption and Text.

CAPTION MODE

1)Closed Caption Characters can be displayed on the TV screen only when the received broadcast signal contains Caption Signals.

2)Paint-on mode: Displays input characters on the screen immediately.

Pop-on mode: Once characters are stored in memory, they are displayed all at once. Roll-up mode: Displays the characters continuously by scrolling (max. 4 lines)

Note: If CAPTION C1 or C2 is selected but a Closed Caption signal is not included, characters will not be displayed.

Notes:

1)When your TV receives a special effects playback signal (i.e., Search, Slow, Still) from a VCR’s video output channel (CH3 or CH4), your TV may not display the correct caption or text.

2)Captions and texts may not match the TV voice exactly.

3)Interference may cause the closed caption system not to function properly.

4)The caption or text characters will not be displayed while the menu display or functions display is shown.

5)If you see this screen:

TEXT MODE

1)Displays the text on the screen by scrolling (max. 7 lines)

2)If the received broadcast signal does not contain caption or text signals, no change will occur.

If your TV displays a black box on the screen, this means that your TV is set to TEXT mode. To clear screen, select CAPTION C1, C2 or CAPTION [OFF].

PORTABLE CART WARNING
S3126A
SYMBOLE D'AVERTISSEMENT POUR
LES COMPOSANTES
APPAREIL ET MEUBLE A ROULETTES
S3126A

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

 

CAUTION

 

THIS SYMBOL INDICATES THAT DAN-

 

 

 

 

GEROUS VOLTAGE CONSTITUTING A

 

RISK OF ELECTRIC SHOCK

 

 

 

 

RISK OF ELECTRIC SHOCK IS PRE-

 

DO NOT OPEN

 

 

 

 

 

 

SENT WITHIN THIS UNIT.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

 

 

 

THIS SYMBOL INDICATES THAT

SHOCK, DO NOT REMOVE COVER (OR BACK) NO

 

 

THERE ARE IMPORTANT OPERATING

USER SERVICEABLE PARTS INSIDE. REFER SER-

 

 

AND MAINTENANCE INSTRUCTIONS

VICING TO QUALIFIED SERVICE PERSONNEL.

 

 

IN THE LITERATURE ACCOMPANYING

 

 

 

 

 

 

 

 

THE APPLIANCE.

 

 

 

 

 

The important note is located on the rear of the cabinet.

IMPORTANT SAFEGUARDS

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

 

ANTENNA

 

LEAD IN

 

WIRE

 

GROUND

 

CLAMP

 

ANTENNA

 

DISCHARGE UNIT

 

(NEC SECTION 810-20)

ELECTRIC

 

SERVICE

 

EQUIPMENT

 

 

GROUNDING CONDUCTORS

 

(NEC SECTION 810-21)

 

GROUND CLAMPS

NEC - NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

 

ELECTRODE SYSTEM

S 2 8 9 8 A

(NEC ART 250, PART H)

1.Read instructions-All the safety and operating instructions should be read before the appliance is operated.

2.Retain Instructions-The safety and operating instructions should be retained for future reference.

3.Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to.

4.Follow Instructions-All operating and use instructions should be followed.

5.Cleaning-Unplug TV from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.

6.Attachments-Do not use attachments not recommended by the TV manufacturer as they may cause hazards.

7.Water and Moisture-Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

8.Accessories-Do not place this TV on an unstable cart, stand, tripod, bracket, or table. The TV may fall,

causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the TV.

Any mounting of the appliance should follow the manufacturer’s instructions and

should use a mounting accessory recommended by the manufacturer. An appliance and cart combi-

nation should be moved with care. Quick stops, excessive force, and uneven surfaces may

cause the appliance and cart combination to overturn.

AMEUBLESCet appareil ne doit être placé que sur un meuble (avec ou sans roulettes) recommandé par le fabricant. Si vous l’installez

sur un meuble à roulettes, déplacez les deux ensembles avec précaution. Un arrêt

brusque, l’utilisation d’une force excessive et des surfaces irrégulières risquent de désta-

biliser l’ensemble et de le renverser.

9.Ventilation-Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the TV on a bed, sofa, rug, or other similar surface. This TV should never be placed near or over a radiator or heat register. This TV should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to .

10.Power Sources-This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TVs intended to operate from battery power, or other sources, refer to the operating instructions.

11.Grounding or Polarization-This TV is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

12.Power-Cord Protection-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

13.Outdoor Antenna grounding-If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

14.Lightning-For added protection for this TV receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power-line surges.

15.Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16.Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV.

18.Servicing-Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19.Damage Requiring Service-Unplug this TV from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power supply cord or plug is damaged or frayed.

b.If liquid has been spilled, or objects have fallen into the TV.

c.If the TV has been exposed to rain or water.

d.If the TV does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to its normal operation.

e.If the TV has been dropped or damaged in any way.

f.When the TV exhibits a distinct change in perfor- mance-this indicates a need for service.

20.Replacement Parts-When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.

21.Safety Check-Upon completion of any service or repairs to this TV, ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition.

22.Heat-This TV product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

OPERATING CONTROLS AND FUNCTIONS

- FRONT PANEL -

VIDEO

L-AUDIO-R

HEADPHONE

MENU

1

2

3

4

- REMOTE CONTROL -

 

 

 

 

15

7

POWER

 

GAME

SLEEP

 

 

 

14

 

 

 

 

DISPLAY

 

1

2

3

13

9

4

5

6

CHANNEL

 

 

 

 

 

 

RETURN

 

7

8

9

12

0

+100

 

 

INPUT

 

 

SELECT

11

 

 

6

CH

 

 

 

VOL

VOL

 

5

CH

 

 

MUTE

10

 

 

MENU

4

1.VIDEO (IN) jack- Connect to the video output jack of a video camera or VCR.

2.AUDIO (IN) L/R jacks- Connect to the left/right channel audio output jacks of a video camera or VCR.

Note : The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for connecting monaural audio equipment.

VOLUME

CHANNEL

POWER

5

6

7

8

3.HEADPHONE jack- To connect headphone (not supplied) for personal listening.

4.MENU button- Press to display the menu on the TV screen.

5.VOLUME (VOL) /buttons- Press to control the volume level.

Press to determine the setting mode from the menu on the TV screen (only the VOL

button).

Press to select or adjust from a particular menu (for example: Language Selection, Channel Presetting, Closed Caption Selection, Picture Adjustment, V-CHIP Set Up).

6.CHANNEL (CH) /buttons- Press to select memorized channel.

Press to select the setting mode from the menu on the TV screen.

Press to select item you want to adjust in the picture control mode.

7.POWER button- Press to turn the TV ON and OFF.

8.Infrared Sensor Window- Receives the infrared control signals from the remote control unit.

9.Channel number buttons- Press two digits to directly access the desired channel. Remember to press a “0” before a single digit channel.

+100 button- Press to select cable channels higher than 99.

10.MUTE button- Press to turn off the sound portion of the TV program (Volume level display turns LIGHT RED from LIGHT BLUE). Press this button again or press the VOL(ume) or button to restore sound.

- REAR PANEL -

ANT.IN

AUDIO

 

IN

S-VIDEO

 

18

2

16

17

11.INPUT SELECT button- Press to select TV or the external input (VIDEO1 or VIDEO2) mode (See USING AUDIO/ VIDEO INPUT JACKS).

12.CHANNEL RETURN button- Press to go back to the previously viewed channel. For example, pressing this button once will change channel display from CH 3 (present channel) to CH 10 (previously viewed channel), and pressing it a second time will return from CH 10 to CH 3.

13.DISPLAY button- Press to display the channel number on the screen. If you press it again, the channel number will disappear.

14.SLEEP button- Press to display the sleep timer and start the function. The shut off time can be determined by the number of times you press the button (0, 10, 20, 30,..90, 0 minutes).

15.GAME button- Press to set Game mode. Press the INPUT SELECT button to exit (See USING AUDIO/VIDEO INPUT JACKS and PICTURE ADJUSTMENT).

16.S-VIDEO (input) jack- Connect to the S-VIDEO output jack of a video camera or VCR using the S-VIDEO cable (not supplied).

17.ANT(enna). IN jack- Connect to an antenna, cable system, or satellite system.

18.AC cord- Connect to a standard AC outlet (120V/60Hz).

Note: Unwrap the AC cord completely from the backcover before plugging the cord into an AC outlet.

INSTALLING THE BATTERIES

1)Slide the battery compartment cover back on the remote unit.

2)Insert 2 “AA” penlight batteries into battery compartment in the direction as indicated by the polarity (+ / -) markings.

Batteries installed with incorrect polarity may damage the remote unit.

3)Replace the cover.

USING AUDIO/VIDEO INPUT JACKS

When you use the AUDIO/VIDEO input jacks, select “VIDEO1” or “VIDEO2” mode by pressing the INPUT SELECT button on the remote control.

To use the jacks on the back of the TV, select “VIDEO1”.

To use the jacks on the front of the TV,

select “VIDEO2”.

Note:

You may also set the Game mode and VIDEO2 at the same time by pressing the GAME button on the remote control. “GAME” appears on the TV screen. In this case, connect the external source to the AUDIO/VIDEO jacks on the front panel (See PICTURE ADJUSTMENT).

+ 6 hidden pages