FUNAI F419TB, F413TB User Manual [en, es]

341.13 Kb
Loading...

FUNAI CORPORATION

LIMITED WARRANTY

FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:

DURATION:

PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does not apply to any the product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.

THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS WILL BE CHARGED.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE.

To locate your nearest FUNAI Authorized Service Center or general service procedure, please call 1-800-242-7158 or write to the following:

FUNAI CORPORATION

Customer Service

100 North Street; Teterboro, NJ 07608

Tel :1-800-242-7158

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

0EMN01749

Printed in Malaysia

 

L1301UB/L1401UB * * * * *

Owner’s

Manual

TELEVISION

F413TB (13 inch)

 

 

F419TB (19 inch)

FEATURES

 

Tinted, Bright Black Matrix Picture Tube

181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.

PLL Frequency Synthesized Tuning- The latest PLL frequency synthesized electronic tuning system provides free and easy channel selection, and lets you tune directly to any channel using the channel number buttons (0~9 and +100-key) on the remote control.

On-Screen Function Display.

Full-Function Remote Control

Sleep Timer

Closed Caption Decoder- You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or text display added to the program.

Auto Shut Off Function- If there is no air signal input from the antenna terminal and no operation for 15 minutes, the TV will turn itself off automatically.

V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.

PRECAUTION

Place your TV in a room with adequate ventilation.

Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.

Do not place your TV on soft surfaces, such as rugs or blankets.

Leave enough room for air to circulate around the bottom, top and back of the set.

The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.

Date of Purchase

Dealer Phone No.

Dealer Purchase from

Model No.

Dealer Address

Serial No.

This Owner’s Manual is made of recycled paper.

IF YOU NEED ADDITIONAL ASSISTANCE FOR SET-UP OR OPERATING AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-242-7158.

ANTENNA/CABLE CONNECTIONS

(13” model only)

Before plugging the UHF/VHF Rod Antenna into the ANT(enna). IN jack, check that the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the ANT(enna). IN jack.

Bent pin

Cable Plug

(Needs to be straightened)

(Straight pin)

VHF/UHF

UHF/VHF Rod Antenna (Supplied with 13 inch model only)

VHF

Antenna

(Not supplied)

UHF Antenna

(Not supplied)

ANT. IN

OR

VHF/UHF Combiner (Not supplied)

Combination Antenna (Not supplied)

*Some cable TV systems use scrambled signals and require a special converter to receive these channels. Consult your local cable company.

CATV Box * or Satellite Box (Not supplied)

OUT IN

75-ohm Coaxial Cable

OR

From Cable System or Satellite Antenna 75-ohm

Coaxial Cable

From Cable System

FCC WARNINGThis equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

CLOSED CAPTION

This TV can receive C1 and C2 of Caption and Text.

Caption Mode

(1)Characters can be displayed on the TV screen when the received broadcast signal contains the Caption Signals.

(2)Paint-on mode: Displays input characters on the screen immediately.

Pop-on mode: Once characters are stored in memory, it is displayed all at once. Roll-up mode: Displays the characters continuously by scrolling (max. 4 lines)

Note: If the CAPTION C1 or C2 is selected but the caption signal is not included, characters will not be displayed.

Notes:

(1)When your TV receives a special effects playback signal (i.e., Search, Slow, Still) from a VCR’s video output channel (CH3 or CH4), your TV may not display the correct caption or text.

(2)Captions and texts may not match the TV voice exactly.

(3)Interference may cause the closed caption system not to function properly.

(4)The caption or text characters will not be displayed while the menu display or function’s display is shown.

(5)If you see this screen!!

Text Mode

(1)Displays the text on the screen by scrolling (max. 7 lines)

(2)If the received broadcast signal does not contain the caption or text signal, no change will occur.

If your TV displays a black box on the screen, this means that your TV is set to TEXT mode. To clear screen, select CAPTION C1, C2 or CAPTION [OFF].

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

 

CAUTION

 

THIS SYMBOL INDICATES THAT DAN-

 

 

 

 

GEROUS VOLTAGE CONSTI-TUTING A

 

RISK OF ELECTRIC SHOCK

 

 

 

 

RISK OF ELECTRIC SHOCK IS PRE-

 

DO NOT OPEN

 

 

 

 

 

 

SENT WITHIN THIS UNIT.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

 

 

 

THIS SYMBOL INDICATES THAT

SHOCK, DO NOT REMOVE COVER (OR BACK) NO

 

 

THERE ARE IMPORTANT OPERATING

USER SERVICEABLE PARTS INSIDE. REFER SER-

 

 

AND MAINTENANCE INSTRUCTIONS

VICING TO QUALIFIED SERVICE PERSONNEL.

 

 

IN THE LITERATURE ACCOMPANY-ING

 

 

 

 

 

 

 

 

THE APPLIANCE.

 

 

 

 

 

The important note is located on the rear of the cabinet.

IMPORTANT SAFEGUARDS

1.

Read instructions-All the safety and operating instruc-

by the manufacturer. An appliance and cart combina-

 

tions should be read before the appliance is operated.

tion should be moved with care. Quick stops, excessive

2.

Retain Instructions-The safety and operating instruc-

force, and uneven surfaces may cause the appliance

 

tions should be retained for future reference.

and cart combination to overturn.

3.

Heed Warnings-All warnings on the appliance and in

9. Ventilation-Slots and openings in the cabinet and the

 

the operating instructions should be adhered to.

back or bottom are provided for ventilation and to

4.

Follow Instructions-All operating and use instructions

ensure reliable operation of the TV and to protect it

 

should be followed.

 

from overheating, these openings must not be blocked

5.

Cleaning-Unplug TV from the wall outlet before clean-

or covered. The openings should never be blocked by

 

ing. Do not use liquid cleaners or aerosol cleaners. Use

placing the TV on a bed, sofa, rug, or other similar sur-

 

a damp cloth for cleaning.

 

face. This TV should never be placed near or over a

 

EXCEPTION: A product that is meant for uninterrupt-

radiator or heat register. This TV should not be placed

 

ed service and, that for some specific reason, such as

in a built-in installation such as a bookcase or rack

 

the possibility of the loss of an authorization code for a

unless proper ventilation is provided or the manufac-

 

CATV converter, is not intended to be unplugged by

turer’s instructions have been adhered to .

 

the user for cleaning or any other purpose, may

10. Power Sources-This TV should be operated only from

 

exclude the reference to unplugging the appliance in

the type of power source indicated on the marking

 

the cleaning description otherwise required in item 5.

label. If you are not sure of the type of power supply to

6.

Attachments-Do not use attachments not recommended

your home, consult your appliance dealer or local

 

by the TV manufacturer as they may cause hazards.

power company. For TVs intended to operate from bat-

7.

Water and Moisture-Do not use this TV near water, for

tery power, or other sources, refer to the operating

 

example, near a bath tub, wash bowl, kitchen sink, or

instructions.

 

laundry tub, in a wet basement, or near a swimming

11. Grounding or Polarization-This TV is equipped with a

 

pool, and the like.

 

polarized alternating-current line plug(a plug having

8.

Accessories-Do not place this TV on an unstable cart,

one blade wider than the other). This plug will fit into

 

stand, tripod, bracket, or table. The TV may fall, caus-

the power outlet only one way. This is a safety feature.

 

ing serious injury to someone, and serious damage to

If you are unable to insert the plug fully into the outlet,

 

the appliance. Use only with a cart, stand, tripod,

try reversing the plug. If the plug should still fail to fit,

 

bracket, or table recommended by

PORTABLE CART WARNING

contact your electrician to replace your obsolete outlet.

 

the manufacturer, or sold with the

Do not defeat the safety purpose of the polarized plug.

 

 

 

TV.

 

12. Power-Cord Protection-Power-supply cords should be

 

Any mounting of the appliance

 

routed so that they are not likely to be walked on or

 

should follow the manufacturer’s

 

pinched by items placed upon or against them, paying

 

instructions and should use a

 

particular attention to cords at plugs, convenience

 

mounting accessory recommended

 

receptacles, and the point where they exit from the

 

 

S3126A

appliance.

 

 

 

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

 

ANTENNA

 

LEAD IN

 

WIRE

 

GROUND

 

CLAMP

 

ANTENNA

 

DISCHARGE UNIT

 

(NEC SECTION 810-20)

ELECTRIC

 

SERVICE

 

EQUIPMENT

 

 

GROUNDING CONDUCTORS

 

(NEC SECTION 810-21)

 

GROUND CLAMPS

NEC - NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

 

ELECTRODE SYSTEM

S 2 8 9 8 A

(NEC ART 250, PART H)

13.Outdoor Antenna grounding-If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

14.Lightning-For added protection for this TV receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power-line surges.

15.Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16.Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV.

18.Servicing-Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19.Damage Requiring Service-Unplug this TV from the

wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power supply cord or plug is damaged or frayed.

b.If liquid has been spilled, or objects have fallen into the TV.

c.If the TV has been exposed to rain or water.

d.If the TV does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to its normal operation.

e.If the TV has been dropped or damaged in any way.

f.When the TV exhibits a distinct change in perfor- mance-this indicates a need for service.

20.Replacement Parts-When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.

21.Safety Check-Upon completion of any service or repairs to this TV, ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition.

22.Heat-This TV product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

This manual covers 13" and 19". The operation of the two models are exactly the same except the appearance. 19" model is illustrated in this manual.

OPERATING CONTROLS AND FUNCTIONS

- FRONT PANEL -

MENU

VOLUME

1 2

- REMOTE CONTROL -

4

POWER

 

 

SLEEP

 

 

 

10

 

 

 

 

DISPLAY

 

1

2

3

9

6

4

5

6

CHANNEL

 

 

 

 

 

 

RETURN

 

7

8

9

8

 

 

0

+100

 

3

CH

 

VOL

VOL

 

2

CH

 

 

MUTE

7

 

 

MENU

1

CHANNEL

POWER

3

4

5

1.MENU button- Press to display the menu on the TV screen.

2.VOLUME /buttons- Press to control the volume level.

Press to determine a setting mode from the menu on the TV screen. (only the VOL button)

Press to select or adjust from a particular menu. (for example: Language Selection, Channel Presetting, Closed Caption Selection, Picture Adjustment, V-CHIP Set Up)

3.CHANNEL /buttons- Press to select memorized channel.

Press to select a setting mode from the menu on the TV screen.

Press to select item you want to adjust in the picture control mode.

4.POWER button- Press to turn the TV ON and OFF.

5.Infrared Sensor Window- Receives the infrared control signals from the remote control unit.

6.CHANNEL NUMBER button- Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel.

+100 button- Press to select cable channels which are equal or greater than number 100.

7.MUTE button- Press the MUTE button to turn off the sound portion of the TV program. (Volume level display turns LIGHT

- REAR PANEL -

ANT.IN

12

RED from LIGHT BLUE.) Press the MUTE button again or press the VOL(ume)

or button to restore sound.

8.CHANNEL RETURN button- Press this button to go back to the previously viewed channel. For example, pressing the CHANNEL RETURN button once will change channel display from CH 3 (present channel) to CH 10 (previously viewed channel), and pressing it a second time will return from CH 10 to CH 3.

9.DISPLAY button- Press to display the channel number on the screen. If you press it again, the channel number will disappear.

10.SLEEP button- Press the SLEEP button to display the sleep timer and start the function. The shut off time can be determined by the number of times you press the button. (0, 10, 20, 30,..90, 0 minutes)

11.ANT(enna). IN jack- Connect to an antenna, cable system, or satellite system.

12.AC cord- Connect to a standard AC outlet (120V/60Hz).

NOTE: Remove the AC cord from the hook to avoid breaking a wire before you connect to a standard AC outlet.

11

INSTALLING THE BATTERIES

1

Slide the battery compartment cover on the remote unit.

2

Insert 2 "AA" penlight batteries into battery compartment in the direction as indicated by the polarity (+ / -) markings. Batteries installed with incorrect polarity may damage the remote unit.

3

Replace the cover.

SLEEP 10
To cancel the sleep timer:
Press the SLEEP button repeatedly until "SLEEP 0" is displayed.

PREPARATION FOR USE

LANGUAGE SELECTION

If you want to change the language of the on-screen menu, follow the procedure below.

1

Connect the power cord to a standard AC outlet.

2

Press the POWER button to turn on the TV.

3

Press the MENU button so that the menu display appears on the TV screen.

4

Press the CH(annel) or button to point to "[ENGLISH]".

5

Select "ENGLISH" or "ESPAÑ OL" = Spanish by using the VOL(ume) or button.

PICTURE CHANNEL SET [ENGLISH]ESPAÑ OL V-CHIP SET UP CAPTION [OFF]

PICTURE CHANNEL SET [ENGLISH]ESPAÑ OL V-CHIP SET UP CAPTION [OFF]

6

Press the MENU button to exit the menu.

CHANNEL PRESETTING

To preset a channel or to change a preset channel, follow the procedure below.

1

Press the POWER button to turn on the TV.

2

Press the MENU button so that the menu display appears on the TV screen.

3

Press the CH(annel) or button to point to "CHANNEL SET". Then, press the VOL(ume) button.

PICTURE CHANNEL SET [ENGLISH]ESPAÑ OL V-CHIP SET UP CAPTION [OFF]

PICTURE CHANNEL SET [ENGLISH]ESPAÑ OL V-CHIP SET UP CAPTION [OFF]

4

Press the CH(annel) or button to point to "AUTO MEMO". Then, press the VOL(ume) button.

The tuner scans and memorizes all active channels in your area.

The TV distinguishes between standard TV channels and cable channels.

When AUTO MEMO action is completed, the lowest memorized channel reappears on the screen.

When you press the CH(annel) or button after

selecting AUTO MEMO, the tuner will stop at the memorized channels only.

The TV may recognize TV channels to be CATV channels

by the receiving conditions. In this case, try AUTO MEMO action again in the fine receiving conditions.

ADD/DELETE AUTO MEMO

[ADD/DELETE FUNCTION]

1)Press the MENU button so that the menu display appears on the TV screen.

2)Press the CH(annel) or button to point to "CHANNEL SET". Then, press the VOL(ume) button.

3)Press the VOL(ume) button so that "ADD/DELETE" is selected.

4)Use the CH(annel) or button to select the

channel you wish to put into memory or to erase from memory. Note: The display will return to the screen in about 10 seconds. Perform "ADD/DELETE" function while this display appears on the

screen.

Press the VOL(ume) or button to light up the channel number in LIGHT BLUE if you wish to add the channel into memory.

Press the VOL(ume) or button to light up the channel number

in LIGHT RED if you wish to erase the channel from memory. 5) Press the MENU button to exit the menu.

PICTURE CHANNEL SET [ENGLISH]ESPAÑ OL V-CHIP SET UP CAPTION [OFF]

ADD/DELETE

AUTO MEMO

RESUME FUNCTION

If the power fails or is disconnected while the TV is powered on, the TV will turn on automatically when the power resumes.

OPERATIONS

WATCHING A TV PROGRAM

1)Press the POWER button to turn on the TV.

2)Select the desired channel with the CH(annel) or button.

3)Adjust the volume to the desired listening level using the VOL(ume) or button.

4)Adjust picture controls for a natural looking image. (See "PICTURE ADJUSTMENT".)

SETTING THE SLEEP TIMER

The sleep timer function enables you to shut off the power without pressing the POWER button after a desired time period.

1)Press the POWER button to turn on the TV and press the SLEEP button on the remote control .

2) You may change the sleep time with pressing the SLEEP button on the remote control repeatedly. The timer is set up to 90 minutes, 10 minutes each time the SLEEP button is pushed. (The timer display counts up and sleep timer will be displayed on the screen when you press the SLEEP button on remote control.)

Note: When you disconnect the unit from the AC outlet, or if you have a power failure, the sleep time will be lost.

CLOSED CAPTION SELECTION

You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or text display added to the program.

: Press the VOL(ume) or button.

1)Press the MENU button so that the menu display appears on the TV screen.

2)Press the CH(annel) or button to point to "CAPTION".

3)Press the VOL(ume) or button to select the mode you wish.

4)When done, press the MENU button to exit the menu.

PICTURE

PICTURE

PICTURE

PICTURE

PICTURE

CHANNEL SET

CHANNEL SET

CHANNEL SET

CHANNEL SET

CHANNEL SET

[ENGLISH]ESPAÑ OL

[ENGLISH]ESPAÑ OL

[ENGLISH]ESPAÑ OL

[ENGLISH]ESPAÑ OL

[ENGLISH]ESPAÑ OL

V-CHIP SET UP

V-CHIP SET UP

V-CHIP SET UP

V-CHIP SET UP

V-CHIP SET UP

CAPTION [OFF]

CAPTION [ C1]

CAPTION [ C2]

CAPTION [ T1]

CAPTION [ T2]

PICTURE ADJUSTMENT

1)Press the MENU button so that the menu display appears on the TV screen.

2)Press the VOL(ume) button so that "PICTURE" is selected.

3)Select the feature you wish to adjust with the CH(annel) or button and adjust it with the VOL(ume) or button.

GAME MODE

Set to the most suitable position for TV GAME.

[+] : ON

[ - ] : OFF

BRIGHT

Adjust until the whitest parts of the picture are as bright as you prefer.

[+] : increase brightness [ - ] : decrease brightness

CONTRAST

Adjust to increase or decrease contrast. [+] : increase contrast

[ - ] : decrease contrast

COLOR

Adjust to be brilliant or pale color. [+] : be brilliant color

[ - ] : be pale color

TINT

Adjust to obtain natural skin tones. [+] : greenish tone

[ - ] : reddish tone

Notes:

In the above steps, the picture adjustment display will disappear from the TV screen after about 10 seconds unless you press any buttons, even though you may not be finished. Press the MENU and VOL(ume) button so that "PICTURE" is selected. Then, press the CH(annel) or button repeatedly until the display returns to the screen.

If you adjust the other Picture control after you set the Game mode to [ON], the Game mode is set to [OFF] automatically. If you want to set the Game mode, reset it to [ON].

: Press the CH(annel) or button.

[-]

GAME MODE [+]

[-]

BRIGHT

[+]

[-] CONTRAST [+]

[-]

COLOR

[+]

[-]

TINT

[+]

OFF

ON

 

 

 

 

 

 

 

 

 

 

+ 5 hidden pages