Fujitsu RX200 User Manual

0 (0)

PRIMERGY RX200 S2

Serversystem

Options Guide

Edition October 2004

CommentsSuggestionsCorrections

The User Documentation Department would like to know your opinion of this manual. Your feedback helps us optimize our documentation to suit your individual needs.

Fax forms for sending us your comments are included in the back of the manual.

There you will also find the addresses of the relevant

User Documentation Department.

Certified documentation according to DIN EN ISO 9001:2000

To ensure a consistently high quality standard and user-friendliness, this documentation was created to meet the regulations of a quality management system which complies with the requirements of the standard DIN EN ISO 9001:2000.

cognitas. Gesellschaft für Technik-Dokumentation mbH www.cognitas.de

Copyright and Trademarks

Copyright © 2004 Fujitsu Siemens Computers GmbH.

All rights reserved.

Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.

This manual is printed on paper treated with chlorine-free bleach.

Fujitsu RX200 User Manual

Preface

Procedure

Safety Instructions

Preparation

Main Memory

Processors

Accessible Drives

Controllers in Non-Hot-Plug PCI Slots

RemoteView Components

Completion

Continued

Abbreviations

Related publications

Index

Contents

1

Preface . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . .

1

1.1

Overview of the documentation

. . . . . . . . . . . . . . . . . .

1

1.2Extensions and conversions . . . . . . . . . . . . . . . . . . . . 3

1.3Notational conventions . . . . . . . . . . . . . . . . . . . . . . . 5

2Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 9

4Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.1

Opening the server . . . . . . . . . . . . . . . . . . . . . . .

15

5

Main Memory . . . . . . . . . . . . . . . . . . . . . . . . . .

17

5.1Installation rules . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.2

Upgrading / exchanging main memory . . . . . . . . . . . . .

18

6

Processors . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

6.1

Installing a second processor . . . . . . . . . . . . . . . . . .

19

6.2

Exchanging the processor . . . . . . . . . . . . . . . . . . .

24

6.3

Exchanging the heat sink . . . . . . . . . . . . . . . . . . . .

27

7

Accessible Drives . . . . . . . . . . . . . . . . . . . . . . .

29

7.1Installing the LocalView Module . . . . . . . . . . . . . . . . . 30

7.2Installing a CD-ROM/DVD drive . . . . . . . . . . . . . . . . . 32

7.3

Installing a floppy disk drive . . . . . . . . . . . . . . . . . . .

35

8

Controllers in Non-Hot-Plug PCI Slots . . . . . . . . . . . .

39

8.1

Installing controllers . . . . . . . . . . . . . . . . . . . . . . .

40

9

RemoteView Components . . . . . . . . . . . . . . . . . . .

43

9.1

Installing the RemoteView Service Board S2 LP . . . . . . . .

43

10

Completion . . . . . . . . . . . . . . . . . . . . . . . . . . .

45

10.1Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 45

Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

OptionsGuide

1 Preface

The PRIMERGY RX200 S2 is an Intel-based server for mid-tier applications in server farms. The server is well suited for front end services as well as for use as an e-mail server, Internet server, or general applications server.

1.1Overview of the documentation

IPRIMERGY manuals are available in PDF format on the ServerBooks CD which is supplied as part of the ServerView Suite package for every server system.

These PDF files can also be downloaded free of charge from the Internet: At http://manuals.fujitsu-siemens.com you will find an overview page showing the online documentation available on the Internet. You can go to the PRIMERGY Server documentation by clicking on “intel based Servers”.

Concept and target groups

This Options Guide shows you how you can expand and upgrade the server.

VCaution!

The activities described in this manual may only be performed by specialist personnel with technical training.

IHow to install/remove the hot-plug components is described in the Operating Manual for the server.

Additional documentation about the server

The PRIMERGY RX200 S2 documentation comprises the following additional manuals:

The “Security” manual (printed copy always supplied with the server, and available as a PDF file on the ServerBooks CD supplied)

The “Guarantee” manual (printed copy always supplied with the server, and available as a PDF file on the ServerBooks CD supplied)

The Operating Manual for PRIMERGY RX200 S2 (PDF available on the

ServerBooks CD supplied)

The Technical Manual for the system board D1790 (PDF available on the

ServerBooks CD supplied)

OptionsGuide

1

Overview of the documentation

Preface

The “BIOS Setup” manual (PDF available on the ServerBooks CD supplied)

The “Service Supplement for PRIMERGY RX200 S2” (PDF available on the

ServerBooks CD supplied)

The “ServerView Suite” manual (printed copy always supplied with the server, and available as PDF file on the ServerBooks CD supplied)

The “Adaptec HostRAID User’s Guide” (PDF available on the ServerBooks CD supplied)

The “Ergonomics” manual (PDF available on the ServerBooks CD supplied).

IYou can order a supplementary ServerBooks CD by sending an e-mail to the following address, quoting your server data:

Reklamat-PC-LOG@fujitsu-siemens.com

Further sources of information:

Technical Manual on the relevant rack

Manual on the monitor

Manual on ServerView Server Management

Manual on the RemoteView Remote Test and Diagnostics System

Documentation on boards and drives

Documentation on your operating system

Information files on your operating system

(see also “Related publications” on page 53)

2

OptionsGuide

Preface

Extensions and conversions

1.2Extensions and conversions

Second processor

The system board can be upgraded with a second processor. Only processors of the same type may be used on the system board. The second processor must have the same clock frequency as the first processor.

Extension of the main memory

The eight slots for the main memory are suitable for PC2-3200 DDR DIMM memory modules. Their organization in four memory banks, 0 to 3, allows fast memory access with two-way interleaving.

Memory modules must always be installed in pairs. A memory bank must always be fully equipped and with the same type of memory modules.

Additional accessible drives

The accessible drives available are a floppy disk drive and a CD-ROM/DVD drive. The drives can be installed in the two top bays. The left-hand bay is intended for a 3.5 x 0.5 inch floppy drive or a LocalView module, while the righthand bay takes a 5.25 x 0.5 inch CD-ROM/DVD drive.

LocalView module (alphanumeric system display)

The LocalView module gives you the option of displaying system information and hardware system faults alphanumerically. This is an intelligent module with a microcontroller and its own memory, which functions independently of the server system.

The LocalView module consists of an LCD display panel and a toggle switch, both accommodated in a suitable mount. The mechanism used allows the LCD display panel to be pulled out and opened out.

For more information on operation and display modes, see the documentation for the LocalView module [6].

OptionsGuide

3

Extensions and conversions

Preface

Additional controllers in non-hot-plug PCI slots

The system board offers two PCI-X slots:

PCI-X slot 1: 64 bit/133 MHz, max. length 315 mm

PCI-X slot 2: 64 bit/66 MHz, low profile, max. length 175 mm

IBoth slots are not hot-pluggable.

RemoteView

RemoteView provides you with a comprehensive remote test and diagnostics package.

RemoteView Service Board S2 LP

The RemoteView Service Board S2 “low profile” (RSB S2 LP) is a PCI board with a completely independent system, i.e. it has its own operating system with Web server and SNMP agents and can optionally be equipped with an external power supply.

The RSB S2 LP is inserted into a standard-PCI slot via a riser card and connected to the system board by means of a cable.

The RSB S2 LP permits remote diagnosis for system analysis, remote system configuration and remote restart even in the event of operating system failure or hardware faults. It has its own LAN connection and its own COM port. All the functions of the RSB S2 LP are thus available either via LAN or via modem.

4

OptionsGuide

Preface

Notational conventions

1.3Notational conventions

The following notational conventions are used in this manual:

Italics

 

indicate commands, menu items or software programs.

 

 

“Quotation marks”

indicate names of chapters and terms that should be

 

 

emphasized.

 

 

 

Ê

 

text which follows this symbol describes activities that

 

 

must be performed in the order shown.

 

 

 

V

CAUTION!

pay particular attention to text marked with this symbol.

 

Failure to observe this warning may endanger your life,

 

 

damage the server, or lead to loss of data.

 

 

 

I

 

supplementary information, remarks and tips follow this

 

symbol.

Table 1: Notational conventions

OptionsGuide

5

2 Procedure

VCAUTION!

The actions described in this manual should only be performed by engineers, service personnel or technical specialists.

Equipment repairs should only be performed by authorized, qualified staff.

Any failure to observe the guidelines in this manual, and any unauthorized openings and improper repairs could expose the user to risks (e.g. electric shock, fire hazards) and could also damage the equipment.

Please note that any unauthorized opening of the device will result in the invalidation of the warranty and exclusion from all liability.

ÊFirst of all please familiarize yourself with the safety instructions in the chapter “Safety Instructions” on page 9ff.

ÊMake sure that all required manuals (see “Additional documentation about the server” on page 1) are available, printing out the PDF files if necessary.

You will definitely need

the Operating Manual for the server and

the Service Supplement for the server

the Technical Manual for the system board.

ÊShut down the server correctly, switch it off, pull out the power plug, and open the server as described in the chapter “Preparation” on page 15ff.

ÊExtend or upgrade your server as described in the relevant chapter.

IHow to install/remove the hot-plug components is described in the Operating Manual for the server.

ÊClose the server, plug all mains plugs into the power outlets, and switch on the server as described in the chapter “Completion” on page 45ff.

ÊStart the operating system and, if necessary, configure it as required (see the Operating Manual).

OptionsGuide

7

3 Safety Instructions

IThe following safety instructions can also be found in the manual entitled “Safety”.

This device complies with the relevant safety regulations for data processing equipment, including electronic office machines for use in an office environment.

If you have any questions as to whether you can set up the device in your particular environment, please contact your sales outlet or our customer service centre.

VCAUTION!

The actions described in this manual should only be performed by engineers, service personnel or technical specialists.

Equipment repairs should only be performed by qualified staff.

Any failure to observe the guidelines in this manual, and any unauthorized openings and improper repairs could expose the user to risks (e.g. electric shock, fire hazards) and could also damage the equipment.

Please note that any unauthorized opening of the device will result in the invalidation of the warranty and exclusion from all liability.

Before setting up

VCAUTION!

During installation and before operating the device, observe the instructions on environmental conditions for you device.

If the device is brought in from a cold environment, condensation may form both inside and on the outside of the machine.

Before operating the device, wait until it is absolutely dry and has reached approximately the same temperature as the installation site. Failure to observe these guidelines can lead to material damage of the device.

Transport the device only in its original packaging or in packaging which protects it from knocks and jolts.

OptionsGuide

9

Safety Instructions

Installation and operation

VCAUTION!

If the rack model is integrated in an installation that receives power from an industrial (public) power supply network with the IEC309 connector, the (public) power supply protection must comply with the requirements for the non-industrial (public) power supply networks for the type A connector.

The server automatically adjusts to a mains voltage between 100 V and 240 V. Make sure that the local mains voltage is neither above nor below this range.

This device has safety-tested power cables and must only be connected to properly grounded power outlets.

Make sure that the power socket on the device or the grounded mains outlet is freely accessible.

The power switch does not disconnect the device from the mains voltage. To completely disconnect it from the mains voltage, you must remove the power plug from the power outlet.

Always connect the device and the attached peripherals to the same power circuit. Otherwise you run the risk of losing data if, for example, a power outage occurs and the central processing unit is still running but the peripheral device (e.g. a storage subsystem) has failed.

Data cables must be adequately shielded to avoid interference.

For the LAN wiring, the requirements according to standards EN 50173 and EN 50174-1/2 apply. The minimum requirement is the use of a protected LAN line of category 5 for 10/100 Mbps Ethernet, and/or of category 5e for Gigabit Ethernet. The requirements of the specification ISO/IEC 11801 must also be taken into account.

Route the cables in such a way that they do not form a potential hazard (tripping) and that they cannot be damaged. When connecting the device, refer to the relevant notes in the operating manual.

Do not connect or disconnect any data transmission cables during a thunderstorm (lightning hazard).

10

OptionsGuide

Safety Instructions

VCAUTION!

Be careful to ensure that no objects (e.g. jewelry, paper clips etc.) or liquids get inside the device (electric shock, short circuit).

In emergencies (e.g. damaged casing, elements, or cables, penetration of liquids or foreign bodies), switch off the device immediately, remove the power connector from the grounded power outlet, and contact your customer service centre.

Proper operation of the device (in accordance with IEC 60950/DIN EN 60950) is only ensured if the casing is completely assembled and the rear covers for the installation openings have been put in place (electric shock, cooling, fire protection, interference suppression)

Install only system extensions that satisfy the requirements and rules governing safety, electromagnetic compatibility, and telecommunications terminal equipment.

If you install other extensions, you may damage the system or violate these safety regulations.

Information on which system extensions are suitable can be obtained from the customer service centre or your sales outlet.

The components marked with a warning label (e.g. lightning symbol) may only be opened, removed, or exchanged by authorized, qualified personnel.

The warranty is invalidated if the device is damaged during the installation or replacement of system extensions.

You may set only those resolutions and refresh rates specified in the operating manual for your monitor.

Otherwise, you may damage the monitor. If you are in any doubt, contact your sales outlet or customer service centre.

OptionsGuide

11

Safety Instructions

Batteries

VCAUTION!

Incorrect replacement of batteries may lead to risk of explosion. The batteries may only be replaced with identical batteries or with a type recommended by the manufacturer (see the Technical Manual for the system board under “Related publications” on page 67).

Do not throw batteries into the trash can. They must be disposed of in accordance with local regulations concerning special waste.

Replace the lithium battery on the system board in accordance with the instructions in the Technical Manual for the system board (see “Related publications” on page 67).

All batteries containing pollutants are marked with a symbol (a crossed-out garbage can). The marking also contains the chemical symbol of the heavy metal that determines the classification as a pollutant:

Cd Cadmium Hg Mercury Pb Lead

Notes on handling CDs in CD-ROM/DVD drives

VCAUTION!

Use only CDs in proper condition in the CD-ROM/DVD drive of your server to prevent data loss, damage to the device, or injuries.

Therefore, check each CD for damage, cracks, breakage etc. before inserting it in the drive.

Please note that any additional labels applied may change the mechanical properties of a CD and cause imbalance.

Damaged and imbalanced CDs can break at high drive speeds (data loss).

Under certain conditions, sharp-edged pieces of broken CDs can penetrate the cover of the drive (cause damage to the device) and be thrown out of the device (therefore causing injury to uncovered body parts, particularly the face or neck).

12

OptionsGuide

Safety Instructions

ITo protect the CD-ROM/DVD drive and prevent mechanical damage, as well as premature wearing of the CDs, you should observe the following advice:

Only insert the CDs in the drive when needed and remove them after use.

Store the CDs in suitable sleeves.

Protect the CDs from exposure to heat and direct sunlight.

Note on the laser

The CD-ROM/DVD drive contains a light-emitting diode (LED) classified according to IEC 825-1:1993:LASER CLASS 1.

Modules with electrostatic-sensitive devices

Electrostatic-sensitive components are identified by the following sticker:

Figure 1: ESD label

VCAUTION!

When you handle components fitted with ESDs, you must observe the following points under all circumstances:

Remove the power plug from the power socket before inserting or removing components containing ESDs.

You must always discharge static build-up (e.g. by touching a grounded object) before working with such components.

The equipment and tools you use must be free of static charge.

Use a grounding cable designed for this purpose to connect yourself to the system unit as you install components.

OptionsGuide

13

Loading...
+ 47 hidden pages