Fujitsu fi-5120C, fi-5220C User Manual

0 (0)

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

fi-5120C / fi-5220C Image Scanner Operator Guide P3PC-1322-05ENZ2

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

INTRODUCTION

Thank you for purchasing the fi-5120C / fi-5220C Duplex Color Scanner product.

This document describes how to handle fi-5120C / fi-5220C Duplex Color and basic operation methods. Before you start using fi-5120C / fi-5220C Duplex Color be sure to thoroughly read this manual to ensure correct use.

This manual describes the scanning method using ScandAll 21. For users using ScandAll PRO, refer to the manual, "How to use ScandAll PRO".

CONTENTS

Copying of the contents of this manual in whole or in part and copying of the scanner application is forbidden under the copyright law.

The contents of this manual are subject to change without notice.

PFU LIMITED. is not liable whatsoever for any damages resulting from use of this scanner and procedures described in this manual, profit due to defects, and any claims by a third party.

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

Regulatory Information (1)

1 2

FCC Declaration

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is located.

Consult your dealer or an experienced radio/TV technician.

FCC warning:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

ATTENTION

The use of a shielded interface cable is required to comply with the Class B limits of Part 15 of

FCC rules. The length of the AC cable must be 2 meters (6.6 feet) or less.

Canadian DOC Regulations

This digital apparatus does not exceed the Class B limit for radio noise emissions from digital apparatus set out in the Radio interference Regulations of the Canadian Department of Communications.

This Class B digital apparatus complies with Canadian ICES-003.s

Le présent appareil numérique n'émet pas de parasites radioélectriques dépassant les limites applicables aux appareils numériques de la classe B et prescrites dans le Règlement sur le brouillage radioélectrique dictées par le Ministère des Communications du Canada.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Bescheinigung des Herstellers / Importeurs

Für den fi-5120C/fi-5220C wird folgendes bescheinigt:

In Übereinsstimmung mit den Bestimmungen der EN45014(CE) funkentstört

Maschinenlärminformationsverordnung 3. GPSGV: Der höchste Schalldruckpegel beträgt 70 dB (A) oder weniger, gemäß EN ISO 7779.

1 2

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

Regulatory Information (2)

1 2

International ENERGY STAR Program

As an ENERGY STAR Partner, PFU LIMITED has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment. The program backs the development and dissemination of products with functions that effectively reduce energy consumption. It is an open system in which business proprietors can participate voluntarily. The targeted products are office equipment such as computers, monitors, printers, facsimiles, copiers, scanners, and multifunction devices.Their standards and logos are uniform among participating nations.

Use in High-safety Applications

This product has been designed and manufactured on the assumption that it will be used in office, personal, domestic, regular industrial, and general-purpose applications. It has not been designed and manufactured for use in applications (simply called "high-safety applications" from here on) that directly involve danger to life and health when a high degree of safety is required, for example, in the control of nuclear reactions at nuclear power facilities, automatic flight control of aircraft, air traffic control, operation control in mass-transport systems, medical equipment for sustaining life, and missile firing control in weapons systems, and when provisionally the safety in question is not ensured. The user should use this product with adopting measures for ensuring safety in such high-safety applications. PFU LIMITED assumes no liability whatsoever for damages arising from use of this product by the user in high-safety applications, and for any claims or compensation for damages by the user or a third party.

About the Use of Mercury

Lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state, or federal laws.

To avoid unexpected injury, read the following carefully.

Doing the following actions may result in serious personal injuries:

Do not put the substance contained in the lamp in your mouth as it has mercury.

Do not incinerate, crush, or shred the lamps or scanner parts.

Do not breathe the chemical liquid contained in the scanner lamps.

1 2

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

Trademarks

Trademarks

Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation in the United States and/or other countries.

ISIS and QuickScan are trademarks or registered trademarks of EMC Corporation in the United States.

Adobe, the Adobe logo, and Acrobat are either registered trademarks of Adobe Systems Incorporated in the United States and/or other countries.

Other product names are the trademarks or registered trademarks of the respective companies.

How Trademarks Are Indicated In This Manual

References to operating systems (OS) and applications are indicated as follows:

Windows 2000

Microsoft® Windows® 2000 Professional operating system

 

 

Windows XP

Microsoft® Windows® XP Professional operating system (32/64-bit),

 

Microsoft® Windows® XP Home Edition operating system

 

 

Windows Server 2003 Microsoft® Windows Server® 2003 Standard Edition operating system (32/64-bit)

Windows Vista

Microsoft® Windows Vista® Home Basic operating system (32/64-bit),

 

Microsoft® Windows Vista® Home Premium operating system (32/64-bit),

 

Microsoft® Windows Vista® Business operating system (32/64-bit),

 

Microsoft® Windows Vista® Enterprise operating system (32/64-bit),

 

Microsoft® Windows Vista® Ultimate operating system (32/64-bit)

 

 

Where there is no distinction between the different versions of the above operating system, the general term "Windows" is used.

Adobe Acrobat

Adobe® Acrobat ®

 

 

Where there is no distinction between the different versions of the above application, the general term "Adobe Acrobat" is used.

The version of Adobe Acrobat provided with this product may change without notice. If the instructions described in this manual differ from the actual displayed screen, refer to Acrobat's Help.

Manufacturer

PFU LIMITED

International Sales Dept., Imaging Bussines Division, Products Group

Solid Square East Tower, 580 Horikawa-cho, Saiwai-ku, Kawasaki-shi Kanagawa 212-8563, Japan Phone: (81-44) 540-4538

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

Note, Liability

BEFORE USING THIS PRODUCT, PLEASE READ THIS MANUAL CAREFULLY. IF THIS PRODUCT IS NOT USED CORRECTLY, UNEXPECTED INJURY CAN OCCUR TO USERS OR BYSTANDERS.

Keep this manual in a safe place so that it can be easily referred to during use of this product.

While all efforts have been made to ensure the accuracy of all information in this manual, PFU assumes no liability to any party for any damage caused by errors or omissions or by statements of any kind in this manual, its updates or supplements, whether such errors are omissions or statements resulting from negligence, accidents, or any other cause. PFU further assumes no liability arising from the application or use of any product or system described herein; nor any liability for incidental or consequential damages arising from the use of this manual. PFU disclaims all warranties regarding the information contained herein, whether expressed, implied, or statutory.

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

PREFACE (1)

1 2

Safety Precautions

This manual describes important details for ensuring the safe and correct use of this product. Thoroughly read this manual before you start to use this product. In particular, be sure to read and fully understand the Safety Precautions described in this manual before you use this product.

Also, store this manual in a safe place so that it can be easily referred to during use of this product.

Warning Indications Used In This Manual

WARNING

This indication alerts operators to an operation that, if not strictly observed, may result in severe injury or death.

CAUTION

This indication alerts operators to an operation that, if not strictly observed, may result in safety hazards to personnel or damage to equipment.

Symbols Used In This Manual

This manual uses the following symbols in the explanations in addition to the warning indications.

This symbol alerts operators to particularly important information. Be sure to read this information.

This symbol alerts operators to helpful advice regarding operation.

A TRIANGLE symbol indicates that special care and attention is required.

The drawing inside the triangle shows the specific caution.

A CIRCLE with a diagonal line inside shows action which users may not perform.

The drawing inside or under the circle shows the specific action that is not allowed.

Outline characters on a colored background show instructions users should follow.

It may also include the drawing that shows the specific instruction.

1 2

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

PREFACE (2)

1 2

Screen Examples In This Manual

The screen examples in this manual are subject to change without notice in the interest of product improvement. If the actual displayed screen differs from the screen examples in this manual, operate by following the actual displayed screen while referring to the User's Manual of the scanner application you are using. The screenshots in this manual were captured from the FUJITSU TWAIN32 scanner driver, ScandAll 21 Image Capturing Utility Software, FUJITSU ISIS scanner driver, QuickScanimage capturing software and Adobe® Acrobat®.

Warning Label

The following picture shows the warning label used in this scanner.

High Temperature

The glass surface inside the ADF becomes hot during the operation. Be careful not to touch the glass surface inside the ADF.

ATTENTION

Do NOT remove from the scanner, stain or scratch the warning labels.

About Maintenance

The user must not perform repairs on this scanner.

Contact the store where you purchased the scanner or an authorized FUJITSU Image Scanner service provider to have repairs done on this product.

1 2

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

Safety Precautions (1)

1 2 3 4

WARNING

Do not damage the AC cable.

A damaged AC cable may cause fire or electric shock. Do not place heavy objects on AC cables, or pull, bend, twist, heat, damage or modify AC cables.

Do not use damaged AC cables or power plugs, or install any cables or power plugs to loose wall sockets.

Use only specified AC cables and connector cables.

Use only specified AC cables and connector cables. Failure to use the correct cables might cause electric shock and/or equipment failure.

Please do not use the AC cable provided with this scanner for other devices, since this might cause equipment failure and other troubles or an electric shock.

Use this scanner only at the indicated power voltage. Do not connect to multiple-power strips.

Use this scanner only at the indicated power voltage and current. Improper power voltage and current might cause fire or electric shock. Do not connect to multiple-power strips.

Do not touch the AC cable with wet hands.

Do not touch the power plug with wet hands. Doing so can cause electric shock.

Wipe any dust from the power plug.

Wipe off any dust from metal parts on the power plug or metal fittings with a soft, dry cloth.

Accumulated dust can cause fire or electric shock.

Do not install the device in locations that has oil smoke, steam, humidity, and dust.

Do not install the scanner in locations subject to oil smoke, steam, humidity, and dust. Doing so might cause a fire or electric shock.

1 2 3 4

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

Safety Precautions (2)

1 2 3 4

WARNING

Turn the scanner OFF if it is damaged.

If the scanner is damaged for any reason, turn the scanner off and unplug the power cable. Contact the store where you purchased the scanner.

Do not use the scanner if there is a strange odor.

If you detect heat coming from the device or detect other problems such as smoke, strange smells or noises, immediately turn off the scanner and disconnect its power plug. Make sure that any smoke coming from it has stopped, before contacting the store where you bought the scanner or an authorized FUJITSU scanner service provider.

Do not put liquids inside the scanner.

Do not insert or drop metal objects in to the scanner. Do not scan wet documents or documents with paper clips or staples. Do not splash or allow the scanner to get wet.

If foreign objects (water, small metal objects, liquids, etc.) get inside the scanner, immediately turn off the scanner and disconnect the power plug from the power outlet. Then, contact the store where you bought the scanner or an authorized FUJITSU scanner service provider. Pay particular attention to this warning in households where there are small children.

Do not touch the inside of the scanner unless necessary.

Do not take apart or modify the scanner. The inside of the scanner contains high-voltage components. Touching these components might cause electric shock or fire.

1 2 3 4

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

Safety Precautions (3)

1 2 3 4

CAUTION

Do not install the scanner on unstable surfaces.

Make sure that the scanner is installed on a flat, level surface and that none of its parts extend beyond the surface top, such as a desk or table. Do not install the scanner on unstable surfaces. Install the scanner on a level surface that is free of vibration to prevent it from falling.

Install the scanner on a strong surface that will support the weight of the scanner and other devices.

Firmly insert the power plug.

Firmly insert the power plug as far it can go into the power outlet.

Do not block the ventilation ports.

Do not block the ventilation ports. Blocking the ventilation ports generates heat inside of scanner, which may result in fire or scanner failure.

Do not place heavy objects or stand on top of the scanner.

Do not place heavy objects on the scanner or use the scanner's surface top to perform other work. Improper installation might cause injuries and equipment failure.

Do not use the scanner immediately after moving it from a cold place into a warm room.

Do not use the device immediately after moving it from a cold place into a warm room. Condensation may occur, which might lead to scanning errors. Let the device dry about one or two hours before you use it.

Before moving the scanner, disconnect the power plug from the power outlet.

Do not move the scanner with the power and interface cables connected as this can damage the cables, which can later cause fire, electric shock as well as injury.

Before moving the scanner, be sure to disconnect the power plug from the power outlet, and all other data cables. Make sure that the floor is free of any obstructions.

1 2 3 4

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

Safety Precautions (4)

1 2 3 4

CAUTION

Protect the scanner from static electricity.

Install the scanner away from strong magnetic fields and other sources of electronic noise. Also, protect the scanner against any static electricity, which can cause the scanner to malfunction.

Do not use aerosol sprays near the scanner.

Do not use aerosol sprays to clean the scanner. Aerosol sprays can blow dirt and dust inside the scanner, resulting in scanner failure or malfunction.

Avoid any contact when scanner is in use.

Avoid touching any scanner mechanism during scanning since this may cause injuries.

Disconnect the power plug from the power outlet when the scanner is not used for a long period of time.

When the scanner is not going to be used for a long period of time, be sure to disconnect the power plug from the power outlet.

Do not install the scanner in direct sunlight.

Do not install the scanner under direct sunlight or near heating apparatus. Doing so might cause excessive heat to build up inside the scanner, which can cause scanner trouble or even fire. Install the scanner in a well-ventilated location.

Before moving the scanner, make sure the shipping lock is locked.

When moving the scanner, be sure to lock the shipping lock in order to prevent damages to the scanner.

Be aware of the pick spring.

When you perform cleaning, make sure that the inside of the scanner is free of any foreign object, and be careful not to get your hand or the cloth caught on the pick spring (metal part) as a deformed pick spring (metal part) may cause injury.

1 2 3 4

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

Chapter 1 NAMAES AND FUNCTIONS OF PARTS

This chapter describes the scanner parts and their functions.

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

1.1 Checking the Contents of the Scanner Package

When you open the scanner package, please handle the main unit and its attachments carefully.

Make sure it contains all the parts listed in the package contents list that is included in the package box.

If any parts are missing or defective, contact the dealer were you purchased the scanner or an authorized FUJITSU scanner service provider

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

1.2 Names and Functions of Parts (1)

1 2 3 4

This section describes the scanner parts and their functions.

Front

No.

Name

Function

1

ADF

It transports the document to the reading position automatically.

 

(Automatic Document Feeder)

 

2

ADF paper chute

Holds in place the document pages / sheets that are fed into the ADF.

3

Side Guide

It is adjusted to the width of the paper in order not to scan skewed pages.

4

ADF button

Puch this button to open the ADF.

5

Operator panel

This panel consists of a Function No. display, four operating push buttons

and a LED.

 

 

6

Stacker

Scanned documents are ejected from the ADF onto this tray.

7

Flatbed

For scanning documents not the standard sizes

 

 

 

1 2 3 4

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

1.2 Names and Functions of Parts (2)

1 2 3 4

Rear

No. Name

1Security Slot

2Imprinter connector (fi-5120C only)

3SCSI Interface connector

4SCSI ID switch

5USB Interface connector

6DC Inlet

1 2 3 4

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

1.2 Names and Functions of Parts (3)

1 2 3 4

Inside

(for fi-5220C)

No. Name

1Document cover

2Document holding pad

3Document bed

4Shipping lock (located on base)

1 2 3 4

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

1.2 Names and Functions of Parts (4)

1 2 3 4

Removable Parts

Parts that can be removed from the scanner are displayed below.

No. Name

1Document cover (fi-5220C only)

2Pad ASSY

3Pick roller (can be removed)

4ADF paper shute

5Sheet guide

1 2 3 4

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

1.3 Functions of the operator panel

The operator panel is located on the right side of the scanner. This panel comprises of a Function Number display, four buttons and a LED.

No.

Name

Function

1

Function Number display

Indicates the function Number and error status.

2

Function Button

Changes the Function activated by the Send to button (*).

3

Send to Button

Launches the linked application software (*).

4

Scan Button

 

5

Power Button

Turns the scanner ON and OFF.

6

LED

Lights when the scanner is turned ON.

 

 

 

* About the settings on the launcher, refer to FUJITSU TWAIN32 scanner driver help.

Indications on the Function Number display

Indication

8 P 0

1

Function

Blinks only one time upon turning on the scanner.

Indicates that the scanner has been turned ON and is being initialized. Indicates that initialization will soon end.

Indicates that initialization has ended successfully. The scanner is now in "Ready Status".

Indicates that a temporary error occurred when documents were being scanned. A

Unumber appearing in alternation following the U (i.e., 1 or 2, etc.) refers to the type of error.

To return the scanner to the ready status ("1"), press "Scan" or "Send to" button.

Indicates that a device (hardware) alarm has occurred during scanning of documents. "E" and the alarm Number (0 to 9, A,c,d and F) will appear alternately.

ETo return the scanner to the ready status ("1"), press "Scan" or "Send to" button. If this alarm occurs, turn the power off and on again. If the alarm continues after turning the power on again, contact your service engineer.

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

Chapter 2 BASIC SCANNER OPERATIONS

This chapter describes basic scanner operations.

In this chapter Windows XP screenshots are illustrated. The screens and operations may differ slightly if the OS that you are using is other than Windows XP.

Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in this chapter will differ slightly.

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

2.1Turning the Scanner ON (1)

1 2 3 4 5 6

This section describes how to turn the scanner ON.

The following shows the procedure for turning the scanner ON.

1. Press the power button on the operator panel.

The scanner is turned ON, and the green LED on the operator panel lights. Also, while the scanner is being initialized, the indication of the Function Number display changes as follows: "8" -> "P" -> "0" -> "1" The indication "1" means that the operator panel is in the ready status.

Power button

HINT

To turn the scanner OFF, hold the power button down for at least two seconds.

About Power ON/OFF Control

You can select to power the scanner on/off either by pressing the Power button, or by connecting / disconnecting the AC cable.

The procedure is as follows.

1.Open Scanner's Properties.

1)When turning on the power, check that the scanner is connected to your PC.

Refer to "2.2 Connecting the Scanner to a PC in " fi-5120C / fi-5220C Getting Started".

1 2 3 4 5 6

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

Fujitsu fi-5120C, fi-5220C User Manual

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

2.1 Turning the Scanner ON (2)

1 2 3 4 5 6

2) Double click the "Printer and Other Hardware" icon on the Control panel of your PC.

The [Printer and Other Hardware] window appears.

3) On the [Printers and Other Hardware] window, double click the [Scanners and Cameras] icon.

The [Scanners and Cameras] window is displayed.

1 2 3 4 5 6

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

2.1 Turning the Scanner ON (3)

1 2 3 4 5 6

4)Right click [fi-5120Cdj] or [fi-5220Cdj], and select [Properties] from the menu.

The properties dialogbox of fi-5120C or fi-5220C appears.

5)Click the "Device Set" tab.

1 2 3 4 5 6

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

2.1 Turning the Scanner ON (4)

1 2 3 4 5 6

The following screen appears.

1 2 3 4 5 6

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

2.1 Turning the Scanner ON (5)

1 2 3 4 5 6

2. Click [Power Control] button

The following screen is displayed.

3.Select a power ON/OFF control

To power on/off the scanner by pressing the Power button: select "Enable power switch".

To power on/off the scanner by connecting/disconnecting the AC cable: select "Disable power switch".

1 2 3 4 5 6

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

2.1 Turning the Scanner ON (6)

1 2 3 4 5 6

Power Save Mode

The Power Save mode keeps the scanner in a low-powered state after it has been turned ON.

If no operation is performed on the scanner for 15 minutes, the scanner automatically switches to the Power Save mode. In the Power Save mode, the indication of the Function Number display on the operator panel goes out, but the green LED stays lit.

To return from the Power Save mode, perform one of the following:

Load the document on the ADF paper chute.

Press any button on the operator panel.

The scanner will be turned OFF when pressing down the power button for at least two seconds.

Execute a command from the scanner driver.

1 2 3 4 5 6

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

2.2 Loading Documents on the ADF for Scanning

(1)

1 2 3 4

1. Align the edges of the documents.

Confirm that all the documents have the same width.

Check the number of sheets in the document stack.

The standard number of sheets that can be loaded on the scanner is as follows: (For details, see "7.3 Maximum Document Loading Capacity")

A4-size paper or smaller that makes a document stack of 5mm or less

Maximum 50 sheet at A4, 20 lb, or 80 g/m2

2.Fan the documents as follows:

Lightly grip both ends of the document with both hands, and bend the document as follows.

Firmly holding the document with both hands, bend back the document as follows so that the bent section rises up in the middle of the document as follows.

Repeat steps 1) to 2) a few times.

Rotate the document 90 degrees, and fan again.

1 2 3 4

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

2.2 Loading Documents on the ADF for Scanning

(2)

1 2 3 4

3. Load the document on the ADF paper chute.

Pull out the ADF paper chute extension.

Set the documents face-down in the ADF paper chute (so that the side to be scanned faces towards the ADF paper chute).

Load the document facing the ADF paper chute.(face down)

ATTENTION

This scanner can scan ID cards through the Automatic Document Feeder with the following precautions.

Place one card at a time into the Auto Document Feeder.

ID card feeding requires the card to be fed through the Auto Document Feeder in portrait mode as in the following figure.

Smooth cards should be placed face down in the Auto Document Feeder.

Embossed cards (raised lettering) should be placed with the embossed side down.

The card to be scanned should be within the ISO7810 compliance, type ID-1. ISO7810-compliant, Type ID-1 card

Material:

PVC (Poly vinyl chloride) or PVCA (Polyvinyl chloride acetate)

Dimensions:

3.4 inch (height) x 2.1 inch (width) / 86 mm x 54 mm

Thickness:

0.03 ± 0.003inch / 0.76 ± 0.08mm

Cards that are excessively rigid or less flexible may not feed smoothly and excessive noise may occur.

Cards should be clean from oil and without labels.

Cards cannot be scanned when the imprinter is installed.

1 2 3 4

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

fi-5120C / fi-5220C Image Scanner Operator Guide

TROUBLE SHOOTING

CONTENTS MAP

TOP

2.2 Loading Documents on the ADF for Scanning

(3)

1 2 3 4

4. Adjust the side guides to the width of the documents.

Move the side guides so that they touch both sides of the documents. If there is any space between the side guides and the edges of documents, the scanned image may be skewed.

1 2 3 4

All Rights Reserved Copyright 2006-2009 © PFU LIMITED

Loading...
+ 127 hidden pages