Fujitsu DX90 S2, DX80 S2 User Manual

4 (1)

P3AM-4822-12ENZ0

ETERNUS DX80 S2/DX90 S2

Disk storage system

User's Guide -Site Planning-

This page is intentionally left blank.

Preface

Fujitsu would like to thank you for purchasing our ETERNUS DX80 S2/DX90 S2 Disk storage system.

The ETERNUS DX80 S2/DX90 S2 Disk storage system is designed to be connected to Fujitsu (PRIMEQUEST or PRIMERGY) or non-Fujitsu servers.

This manual describes the environmental requirements that are necessary to install and use the ETERNUS DX80 S2/DX90 S2 Disk storage system.

This manual is intended for use of ETERNUS DX80 S2/DX90 S2 Disk storage system in regions other than Japan. Please carefully review the information outlined in this manual.

Twelfth Edition

June 2013

Microsoft, Windows, Windows Server, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Mozilla, Firefox, and the Mozilla and Firefox logos are trademarks or registered trademarks of the Mozilla Foundation in the United States and other countries.

The company names, product names and service names mentioned in this document are registered trademarks or trademarks of their respective companies.

3

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

About this Manual

Organization

This manual is composed of the following four chapters:

Chapter 1 Hardware Configurations

This chapter describes the main components and the relative optional products that are installed in the ETERNUS DX80 S2/DX90 S2 Disk storage system.

Chapter 2 ETERNUS DX Disk Storage System Installation

This chapter describes the installation specifications, the installation environment, and the power requirements.

Chapter 3 Connections

This chapter describes the configuration for each interface to connect to the ETERNUS DX80 S2/DX90 S2 Disk storage system.

Chapter 4 Rack and Optional Product Installation

This chapter describes the requirements for rack installation.

This chapter also describes the standard installation rules (installation locations and installation order) of the optional products before shipment from the factory when the optional products are purchased with the ETERNUS DX80 S2/DX90 S2 Disk storage system at the same time.

Naming Conventions

Abbreviations used in this manual

"ETERNUS DX Disk storage system" refers to the ETERNUS DX80 S2/DX90 S2 Disk storage system.

"CA" refers to a host interface module that is used in an ETERNUS DX Disk storage system to connect to a server.

"Host Bus Adapter (HBA)" refers to the interface module that is normally used by the server to connect to ETERNUS DX Disk storage systems.

An "FC card", "LAN card", "Network Interface Card (NIC)", "Converged Network Adapter (CNA)", or "SAS card" may be used instead, depending on the server and interface.

Trademark symbols such as ™ and ® are omitted in this document.

4

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

About this Manual

Warning Notations

Warning signs are shown throughout this manual in order to prevent injury to the user and/or material damage. These signs are composed of a symbol and a message describing the recommended level of caution. The following explains the symbol, its level of caution, and its meaning as used in this manual.

This symbol indicates the possibility of minor or moderate personal injury, as well CAUTION as damage to the ETERNUS DX Disk storage system and/or to other users and their

property, if the ETERNUS DX Disk storage system is not used properly.

How Warnings are Presented in this Manual

A message is written beside the symbol indicating the caution level. This message is marked with a vertical ribbon in the left margin, to distinguish this warning from ordinary descriptions.

An example is shown here.

Example Warning

 

 

 

 

 

Warning Level Indicator

 

 

 

 

 

 

 

 

 

 

Warning Type Indicator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning Details

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To avoid damaging the ETERNUS DX Disk storage system,

pay attention to the following points when cleaning the ETERNUS DX Disk storage system:

-Make sure to disconnect the power when cleaning.

-Be careful that no liquid seeps into the ETERNUS DX Disk storage system when using cleaners, etc.

-Do not use alcohol or other solvents to clean the ETERNUS DX Disk storage system.

Warning Layout Ribbon

5

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Table of Contents

Chapter 1

Hardware Configurations

11

1.1

Controller Enclosure ..........................................................................................................

11

1.1.1

Controllers .....................................................................................................................................................

15

1.1.2

Power Supply Units ........................................................................................................................................

17

1.2

Drive Enclosures ................................................................................................................

18

1.2.1

I/O Modules ...................................................................................................................................................

21

1.2.2

Power Supply Units ........................................................................................................................................

22

1.3

Enclosure Connection Path ...............................................................................................

22

1.4

Drives

................................................................................................................................

23

1.4.1

2.5" Drives .....................................................................................................................................................

23

1.4.2

3.5" Drives .....................................................................................................................................................

24

1.5

Power Distribution Units (Only for Regions Other than EMEA&I) ......................................

24

Chapter 2

ETERNUS DX Disk Storage System Installation

27

2.1

Installation Specifications .................................................................................................

27

2.1.1

ETERNUS DX80 S2 ..........................................................................................................................................

27

2.1.2

ETERNUS DX90 S2 ..........................................................................................................................................

29

2.2

Storage System Dimensions ..............................................................................................

31

2.2.1

Controller Enclosure Dimensions ...................................................................................................................

31

2.2.2

Drive Enclosure Dimensions ..........................................................................................................................

33

2.3

Package Size .....................................................................................................................

35

2.4

Installation Area ...............................................................................................................

36

2.5

Installation Environment ..................................................................................................

36

2.5.1

Air Conditioning .............................................................................................................................................

36

2.5.2

Earthquake Resistance ..................................................................................................................................

37

2.5.3

Load Bearing Capacity for Floors ....................................................................................................................

37

2.6

Outlet/Socket Specifications ..............................................................................................

37

2.6.1

Specifications for Optional Power Supply Products .........................................................................................

38

2.6.2

Required Number of Outlets/Sockets .............................................................................................................

40

2.7

Circuit Protectors ...............................................................................................................

41

6

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Table of Contents

Chapter 3

Connections

46

3.1

Host Connections ..............................................................................................................

46

3.1.1

Host Interfaces ..............................................................................................................................................

46

3.1.2

Host Connection Path ....................................................................................................................................

48

3.2

Remote Connections .........................................................................................................

52

3.2.1

Remote Interfaces .........................................................................................................................................

53

3.2.2

Connectable Models ......................................................................................................................................

54

3.3

LAN Connection ................................................................................................................

55

3.4

Power Supply Connection ..................................................................................................

56

3.4.1

Input Power Supply Lines ...............................................................................................................................

57

3.4.2

UPS Connection .............................................................................................................................................

59

3.5

Power Synchronized Connections ......................................................................................

60

Chapter 4

Rack and Optional Product Installation

64

4.1

Rack Installation Requirements ........................................................................................

64

4.1.1

Placement in the Rack ...................................................................................................................................

64

4.1.2

Cable Connection ...........................................................................................................................................

65

4.2

Installable Racks ...............................................................................................................

67

4.2.1

Fujitsu Racks ..................................................................................................................................................

67

4.2.2

Non-Fujitsu Racks ..........................................................................................................................................

68

4.3

Standard Installation Rules Before Shipment (Only for Regions Other than EMEA&I) .......

69

4.3.1

Host Interfaces ..............................................................................................................................................

70

4.3.2

Drive Enclosures ............................................................................................................................................

71

4.3.3

Drives

............................................................................................................................................................

72

4.3.4

Drive Installation ...........................................................................................................................Examples

77

7

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

List of Figures

Figure 1.1

Front view of a 2.5" type controller enclosure..............................................................................................

11

Figure 1.2

Rear view of a 2.5" type controller enclosure (single-controller type)..........................................................

12

Figure 1.3

Rear view of a 2.5" type controller enclosure (dual-controller type) ............................................................

12

Figure 1.4

Top view of a 2.5" type controller enclosure ................................................................................................

13

Figure 1.5

Side view of a 2.5" type controller enclosure ...............................................................................................

13

Figure 1.6

Front view of a 3.5" type controller enclosure..............................................................................................

13

Figure 1.7

Rear view of a 3.5" type controller enclosure (single-controller type)..........................................................

14

Figure 1.8

Rear view of a 3.5" type controller enclosure (dual-controller type) ............................................................

14

Figure 1.9

Top view of a 3.5" type controller enclosure ................................................................................................

15

Figure 1.10

Side view of a 3.5" type controller enclosure ...............................................................................................

15

Figure 1.11

Front view of a 2.5" type drive enclosure .....................................................................................................

18

Figure 1.12

Rear view of a drive enclosure (single-IOM type) ........................................................................................

18

Figure 1.13

Rear view of a drive enclosure (dual-IOM type) ...........................................................................................

19

Figure 1.14

Top view of a 2.5" type drive enclosure........................................................................................................

19

Figure 1.15

Side view of a 2.5" type drive enclosure.......................................................................................................

19

Figure 1.16

Front view of a 3.5" type drive enclosure .....................................................................................................

20

Figure 1.17

Rear view of a drive enclosure (single-IOM type) ........................................................................................

20

Figure 1.18

Rear view of a drive enclosure (dual-IOM type) ...........................................................................................

20

Figure 1.19

Top view of a 3.5" type drive enclosure........................................................................................................

21

Figure 1.20

Side view of a 3.5" type drive enclosure.......................................................................................................

21

Figure 1.21

Enclosure connection path (dual-controller type) .......................................................................................

22

Figure 1.22

Enclosure connection path (single-controller type) .....................................................................................

23

Figure 1.23

Power distribution unit (AC200-240V, 1U, Max 2 enclosures connection) ...................................................

24

Figure 1.24

Power distribution unit (AC200-240V, 2U, Max 6 enclosures connection) ...................................................

25

Figure 1.25

Power distribution unit (AC200-240V, 2U, Max 8 enclosures connection) ...................................................

26

Figure 2.1

2.5" type controller enclosure dimensions...................................................................................................

31

Figure 2.2

3.5" type controller enclosure dimensions...................................................................................................

32

Figure 2.3

2.5" type drive enclosure dimensions ..........................................................................................................

33

Figure 2.4

3.5" type drive enclosure dimensions ..........................................................................................................

34

Figure 2.5

Installation area and service area ...............................................................................................................

36

Figure 2.6

Power distribution unit (1U)........................................................................................................................

40

Figure 2.7

Power distribution unit (2U)........................................................................................................................

41

Figure 2.8

Breaking characteristics of distribution board circuit protectors ..................................................................

42

Figure 2.9

Example of a power supply connection using a power distribution unit (1U)..............................................

43

Figure 2.10

Example of a power supply connection using a power distribution unit (2U)..............................................

44

Figure 2.11

Example of a power supply connection without power distribution units....................................................

45

Figure 3.1

Single path connection (direct connection).................................................................................................

48

Figure 3.2

Single path connection (switch connection)................................................................................................

49

Figure 3.3

Multipath connection (direct connection) ...................................................................................................

49

Figure 3.4

Multipath connection (switch connection) ..................................................................................................

50

Figure 3.5

Connection that satisfies the system requirements (for availability)...........................................................

51

Figure 3.6

Connection that satisfies the system requirements (for enhanced performance)........................................

51

Figure 3.7

Example of non-supported connection configuration (when multiple types of

 

 

remote interfaces are installed in the same ETERNUS DX Disk storage system) ..........................................

52

Figure 3.8

Example of supported connection configuration (when multiple types of

 

 

remote interfaces are installed in the same ETERNUS DX Disk storage system) ..........................................

52

Figure 3.9

FC connection for remote copy (redundant path) ........................................................................................

53

Figure 3.10

FC connection for remote copy (using lines)................................................................................................

53

8

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

List of Figures

Figure 3.11

iSCSI connection for remote copy (using lines) ............................................................................................

53

Figure 3.12

Example of a LAN connection......................................................................................................................

55

Figure 3.13

Dual-line power supply when connecting to power sockets.........................................................................

57

Figure 3.14

Dual-line power supply when connecting to UPS units................................................................................

57

Figure 3.15

Single-line power supply when connecting to power sockets ......................................................................

57

Figure 3.16

Single-line power supply when connecting to a UPS unit ............................................................................

58

Figure 3.17

Single-line power supply when connecting to a power socket and a UPS unit.............................................

58

Figure 3.18

Power control using a power synchronized unit (when connecting one or two servers) ..............................

61

Figure 3.19

Power control using a power synchronized unit (when connecting three or more servers) .........................

62

Figure 4.1

AC cable connection ....................................................................................................................................

65

Figure 4.2

QSFP cable connection (single-controller type) ...........................................................................................

66

Figure 4.3

QSFP cable connection (dual-controller type)..............................................................................................

67

Figure 4.4

Unit installation area ..................................................................................................................................

68

Figure 4.5

Installation diagram for a host interface (single-controller type)................................................................

70

Figure 4.6

Installation diagram for host interfaces (dual-controller type)....................................................................

71

Figure 4.7

Installation diagram for 2.5" drives .............................................................................................................

74

Figure 4.8

Installation diagram for 3.5" drives .............................................................................................................

76

Figure 4.9

Drive installation example at shipment (2.5" type controller enclosure).....................................................

77

Figure 4.10

Drive installation example at shipment (3.5" type controller enclosure).....................................................

78

9

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

List of Tables

Table 1.1

Host interface specifications........................................................................................................................

16

Table 1.2

Drive interface port specifications for controllers.........................................................................................

16

Table 1.3

LAN port specifications for controllers .........................................................................................................

17

Table 1.4

PWC port specifications ...............................................................................................................................

17

Table 1.5

Drive interface port specifications for I/O modules ......................................................................................

21

Table 1.6

2.5" drive specifications...............................................................................................................................

23

Table 1.7

3.5" drive specifications...............................................................................................................................

24

Table 1.8

Power distribution unit (AC200-240V, 1U, Max 2 enclosures connection) and

 

 

provided AC cable specifications..................................................................................................................

25

Table 1.9

Power distribution unit (AC200-240V, 2U, Max 6 enclosures connection) and

 

 

provided AC cable specifications..................................................................................................................

25

Table 1.10

Power distribution unit (AC200-240V, 2U, Max 8 enclosures connection) and

 

 

provided AC cable specifications..................................................................................................................

26

Table 2.1

ETERNUS DX80 S2 installation specifications...............................................................................................

27

Table 2.2

ETERNUS DX90 S2 installation specifications...............................................................................................

29

Table 2.3

Package size (for regions other than EMEA&I) ............................................................................................

35

Table 2.4

Specifications for power cords supplied with the ETERNUS DX Disk storage system

 

 

(for the EMEA&I region) ..............................................................................................................................

38

Table 2.5

Specifications for power cords supplied with the ETERNUS DX Disk storage system

 

 

(for regions other than EMEA&I) .................................................................................................................

38

Table 2.6

Specifications for optional power cords (for regions other than EMEA&I)....................................................

38

Table 2.7

Specifications for power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 1U,

 

 

Max 2 enclosures connection) .....................................................................................................................

39

Table 2.8

Specifications for power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 2U,

 

 

Max 6 enclosures connection) .....................................................................................................................

39

Table 2.9

Specifications for power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 2U,

 

 

Max 8 enclosures connection) .....................................................................................................................

39

Table 2.10

Required number of outlets and sockets to install power distribution units ................................................

40

Table 2.11

Required conditions for distribution board circuit protectors .......................................................................

41

Table 3.1

Ethernet frame capacity (Jumbo Frame settings) ........................................................................................

47

Table 3.2

Connectable models and available remote interfaces .................................................................................

54

Table 3.3

ETERNUS Web GUI operating environment ..................................................................................................

55

Table 4.1

Enclosure installation order.........................................................................................................................

64

Table 4.2

Specifications for the unit installation area .................................................................................................

69

Table 4.3

Priority order of host interface installation ..................................................................................................

70

Table 4.4

Priority order of drive enclosure installation (for 2.5" type controller enclosure) .........................................

71

Table 4.5

Priority order of drive enclosure installation (for 3.5" type controller enclosure) .........................................

71

Table 4.6

Priority order of 2.5" drive installation.........................................................................................................

72

Table 4.7

Priority order of 3.5" drive installation.........................................................................................................

75

10

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1

Hardware Configurations

This chapter explains hardware configurations for the ETERNUS DX Disk storage system.

1.1Controller Enclosure

This section explains the main components in the controller enclosure.

The controller enclosure contains drives installed in the front, and controllers and power supply units in the rear.

Since the power supply units are redundant, operations can continue even if one of them fails. There are two models: a single-controller type and a dual-controller type. For a dual-controller type, operations can continue even if one of the controllers fails.

The single-controller type differs from the dual-controller type by the following features:

-The controller and I/O module are not duplicated.

-Hot maintenance or swapping of the controller and I/O module is not possible.

-Concurrent firmware loading or update of the controller firmware and I/O module firmware is not possible.

-Multipath connection to a single server is not available.

-The Thin Provisioning function cannot be used.

-The Flexible Tier function cannot be used.

Fujitsu recommends that the dual-controller types, in which the controller and I/O module are duplicated, be used in a system where a high level of reliability is required.

External views of a 2.5" type controller enclosure

Front view

Figure 1.1 Front view of a 2.5" type controller enclosure

2.5" disk or 2.5" Solid State Drive (SSD)

11

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Fujitsu DX90 S2, DX80 S2 User Manual

Chapter 1 Hardware Configurations

1.1Controller Enclosure

Rear view

Single-controller type

Figure 1.2 Rear view of a 2.5" type controller enclosure (single-controller type)

Host interface (CA#1)

LAN (RMT) port

LAN (MNT) port

Controller (CM#0)

Cover

PWC port

Power supply unit (PSU#0)

Power supply unit (PSU#1)

Drive interface (OUT) port

Host interface (CA#0)

Dual-controller type

Figure 1.3 Rear view of a 2.5" type controller enclosure (dual-controller type)

Host interface (CA#1)

 

Host interface (CA#1)

LAN (RMT) port LAN (MNT) port

LAN (RMT) port LAN (MNT) port

Controller (CM#0)

 

Controller (CM#1)

PWC port

PWC port

Power supply unit (PSU#0)

Power supply unit (PSU#1)

Drive interface (OUT) port

Drive interface (OUT) port

Host interface (CA#0)

Host interface (CA#0)

12

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1 Hardware Configurations

1.1Controller Enclosure

Top view

Figure 1.4 Top view of a 2.5" type controller enclosure

Side view

Figure 1.5 Side view of a 2.5" type controller enclosure

External views of a 3.5" type controller enclosure

Front view

Figure 1.6 Front view of a 3.5" type controller enclosure

3.5" disk or 3.5" Solid State Drive (SSD)

13

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1 Hardware Configurations

1.1Controller Enclosure

Rear view

Single-controller type

Figure 1.7 Rear view of a 3.5" type controller enclosure (single-controller type)

Host interface (CA#1)

LAN (RMT) port

LAN (MNT) port

Controller (CM#0)

Cover

PWC port

Power supply unit (PSU#0)

Power supply unit (PSU#1)

Drive interface (OUT) port

Host interface (CA#0)

Dual-controller type

Figure 1.8 Rear view of a 3.5" type controller enclosure (dual-controller type)

Host interface (CA#1)

 

Host interface (CA#1)

LAN (RMT) port LAN (MNT) port

LAN (RMT) port LAN (MNT) port

Controller (CM#0)

 

Controller (CM#1)

PWC port

PWC port

Power supply unit (PSU#0)

Power supply unit (PSU#1)

Drive interface (OUT) port

Drive interface (OUT) port

Host interface (CA#0)

Host interface (CA#0)

14

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1 Hardware Configurations

1.1Controller Enclosure

Top view

Figure 1.9 Top view of a 3.5" type controller enclosure

Side view

Figure 1.10 Side view of a 3.5" type controller enclosure

1.1.1Controllers

The controller contains a CPU, cache memory, System Capacitor Unit (SCU), non-volatile memory, host interfaces, drive interface ports, and LAN ports. The controller controls all operations in the ETERNUS DX Disk storage system.

CPU

A single core processor is installed.

Cache memory

Cache memory enables high speed processing by storing frequently used data.

The cache memory capacity for each controller is 2GB for the ETERNUS DX80 S2 and 4GB for the ETERNUS DX90 S2.

15

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1 Hardware Configurations

1.1Controller Enclosure

Host interfaces

A host interface (CA) is a board that has interface ports to connect a controller to a server.

Up to two host interfaces can be installed in the controller of an ETERNUS DX Disk storage system. Different types of host interfaces can exist together in the same controller. For details about the installation rules, refer to "4.3.1 Host Interfaces" (page 70).

FC, iSCSI, FCoE, and SAS are available as host interface.

The following table shows the host interface specifications.

Table 1.1 Host interface specifications

Interface

 

Transfer speed (max.)

Connector type

Number of ports for each CA

FC

 

16Gbit/s

LC

2

 

 

 

 

 

8Gbit/s

 

 

 

 

 

 

 

 

 

iSCSI

 

10Gbit/s

LC

 

 

 

 

 

2

 

 

 

SFP+

 

 

 

(direct attach twinax copper)

 

 

 

 

 

 

 

 

1Gbit/s

RJ-45

2

 

 

 

 

 

FCoE

 

10Gbit/s

LC

 

 

 

 

 

2

 

 

 

SFP+

 

 

 

(direct attach twinax copper)

 

 

 

 

 

 

SAS

 

6Gbit/s

miniSAS (SFF-8088)

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FC and iSCSI host interfaces can be used as remote interfaces for remote connections by changing the port mode. The port mode can be set from ETERNUS Web GUI or ETERNUS CLI.

There are two types of iSCSI 10Gbit/s and FCoE host interfaces; an interface type with SFP+ modules (LC connector for an FC cable connection) and an interface type without SFP+ modules (SPF+ connector for a Copper Twinax cable connection).

For SFP+ modules, Short Wave Length (SWL) or Long Wave Length (LWL) types can be installed in 16Gbit/s FC interfaces. The default modules that are installed in 16Gbit/s FC interfaces are SWL type SFP+ modules. To install LWL type SFP+ modules, purchase the Long wave SFP+ modules for the DX80 S2/DX90 S2 separately.

Drive interface ports

A drive interface port is used to connect drive enclosures.

The following table shows the drive interface port specifications.

Table 1.2 Drive interface port specifications for controllers

Interface

Transfer speed (max.)

Connector type

Number of ports for each controller

SAS

6Gbit/s

QSFP

1

 

 

 

 

16

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1 Hardware Configurations

1.1Controller Enclosure

LAN ports

Two LAN ports (RJ-45) are installed in each controller.

Each LAN port is used for operation management (MNT port) and for remote support function (RMT port) respectively.

The following table shows the LAN port specifications.

Table 1.3 LAN port specifications for controllers

Interface

Transfer speed

Connector type

Number of ports

(max.)

for each controller

 

 

Ethernet

1Gbit/s

RJ-45

2

(1000Base-T/100Base-TX/10Base-T)

 

 

 

 

 

 

 

SCU

A System Capacitor Unit (SCU) is installed in a controller as a backup power source in case of power outage. The SCU is charged from an external power source while the ETERNUS DX Disk storage system is running normally. If a power failure is detected, data in the cache memory is saved to the non-volatile memory in the controller using the SCU. There is no limit to the post-failure data retention time.

PWC ports

A PWC port is installed in a controller.

The PWC port is used to connect a power synchronized unit to perform power synchronization.

The following table shows the PWC port specifications.

Table 1.4 PWC port specifications

Interface

Connector type

Number of ports for each controller

RS232C

PWC

1

 

 

 

1.1.2Power Supply Units

The power supply unit transforms input AC power from a power socket to DC power and supplies power to each component. Two power supply units are installed in each controller enclosure.

Each power supply unit contains fans.

17

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1 Hardware Configurations

1.2 Drive Enclosures

1.2Drive Enclosures

This section explains the main components in the drive enclosure.

The drive enclosure contains drives installed in the front, and I/O modules and power supply units in the rear. Up to 24 drives can be installed in a 2.5" type drive enclosure. Up to 12 drives can be installed in a 3.5" type drive enclosure.

Since the power supply units are redundant, operations can continue even if one of them fails. When a drive enclosure is connected, a DE-ID (drive enclosure number) is automatically allocated.

External views of a 2.5" type drive enclosure

Front view

Figure 1.11 Front view of a 2.5" type drive enclosure

2.5" disk or 2.5" Solid State Drive (SSD)

DE-ID display panel

Rear view

Single-IOM type

Figure 1.12 Rear view of a drive enclosure (single-IOM type)

Drive interface (OUT) port

Drive interface (IN) port

I/O module (IOM6#0)

Cover

Power supply unit (PSU#1)

Power supply unit (PSU#0)

18

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1 Hardware Configurations

1.2Drive Enclosures

Dual-IOM type

Figure 1.13 Rear view of a drive enclosure (dual-IOM type)

 

 

Drive interface (OUT) port

 

Drive interface (OUT) port

 

 

 

I/O module

 

 

 

Drive interface (IN) port

 

 

 

Drive interface (IN) port

 

 

 

 

 

 

 

 

 

 

 

 

(IOM6#0)

 

 

 

 

 

 

 

 

I/O module

(IOM6#1)

Power supply unit (PSU#1)

Power supply unit (PSU#0)

Top view

Figure 1.14 Top view of a 2.5" type drive enclosure

Side view

Figure 1.15 Side view of a 2.5" type drive enclosure

19

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1 Hardware Configurations

1.2Drive Enclosures

External views of a 3.5" type drive enclosure

Front view

Figure 1.16 Front view of a 3.5" type drive enclosure

3.5" disk or 3.5" Solid State Drive (SSD)

DE-ID display panel

Rear view

Single-IOM type

Figure 1.17 Rear view of a drive enclosure (single-IOM type)

Drive interface (OUT) port

Drive interface (IN) port

I/O module (IOM6#0)

Cover

Power supply unit (PSU#1)

Power supply unit (PSU#0)

Dual-IOM type

Figure 1.18 Rear view of a drive enclosure (dual-IOM type)

 

 

Drive interface (OUT) port

 

Drive interface (OUT) port

 

 

 

I/O module

 

 

 

Drive interface (IN) port

 

 

 

Drive interface (IN) port

 

 

 

 

 

 

 

 

 

 

 

 

(IOM6#0)

 

 

 

 

 

 

 

 

I/O module

(IOM6#1)

Power supply unit (PSU#1)

Power supply unit (PSU#0)

20

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1 Hardware Configurations

1.2Drive Enclosures

Top view

Figure 1.19 Top view of a 3.5" type drive enclosure

Side view

Figure 1.20 Side view of a 3.5" type drive enclosure

1.2.1I/O Modules

The I/O module is a component that controls the interaction between the controller and the drives. The I/O module is connected to the controller or an I/O module on another drive enclosure.

Drive interface ports

A drive interface port is used to connect a controller enclosure or drive enclosures.

The drive interface port has an IN port and an OUT port.

The following table shows the drive interface port specifications.

Table 1.5 Drive interface port specifications for I/O modules

Interface

Transfer speed (max.)

Connector type

Number of ports for each I/O module

SAS

6Gbit/s

QSFP

1 (IN)

1 (OUT)

 

 

 

 

 

 

 

21

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1 Hardware Configurations

1.3 Enclosure Connection Path

1.2.2Power Supply Units

The power supply unit transforms input AC power from a power socket to DC power and supplies power to each component. Two power supply units are installed in each drive enclosure.

Each power supply unit contains fans.

1.3Enclosure Connection Path

For a dual-controller type, a controller enclosure (CE) is connected to drive enclosures (DE) with multiple paths.

A drive enclosure has two independent drive interface ports. Path redundancy is maintained by connecting the drive enclosure to two controllers directly. This configuration allows operation to continue even if one of the connection paths fails.

Up to nine drive enclosures can be connected to a controller enclosure as shown in the figures below.

Figure 1.21 Enclosure connection path (dual-controller type)

 

 

 

 

DE #09

 

 

 

DI

 

 

DI

 

 

 

 

 

DE #0x

 

 

 

 

 

 

 

DI

 

DE #02

DI

 

 

 

 

 

 

 

 

 

DI

 

 

DI

 

 

 

 

 

 

 

 

 

 

 

DI

 

DE #01

DI

 

 

 

 

 

 

 

 

 

DI

 

 

DI

 

 

 

 

 

 

 

 

 

 

 

DI

 

CE

DI

 

 

 

 

 

 

 

 

DI: Drive interface port

22

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1 Hardware Configurations

1.4 Drives

A connection path is not duplicated in a single-controller type.

Figure 1.22 Enclosure connection path (single-controller type)

DE #09

DI

DE #0x

DI

DE #02

DI

DI

DE #01

DI

DI

CE

DI: Drive interface port

1.4Drives

The following drives can be installed in a controller enclosure and drive enclosure.

1.4.12.5" Drives

The following table shows the 2.5" drive specifications.

Table 1.6 2.5" drive specifications

Drive name

Drive interface

Storage media

Storage capacity

Speed

SAS disks

 

Hard disk

300GB

15,000rpm

 

 

 

 

 

 

 

 

300GB, 450GB, 600GB,

10,000rpm

 

 

 

900GB

 

 

Serial Attached

 

 

 

SAS self encrypting

Hard disk

300GB, 450GB, 600GB,

10,000rpm

disks (SEDs)

SCSI (6Gbit/s)

 

900GB

 

 

 

 

 

 

Nearline SAS disks

 

Hard disk

1TB

7,200rpm

 

 

 

 

 

SSDs

 

Flash memory

100GB, 200GB, 400GB,

 

 

 

800GB

 

 

 

 

 

 

23

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Chapter 1 Hardware Configurations

1.5 Power Distribution Units (Only for Regions Other than EMEA&I)

1.4.23.5" Drives

The following table shows the 3.5" drive specifications.

Table 1.7 3.5" drive specifications

Drive name

Drive interface

Storage media

Storage capacity

Speed

SAS disks

 

Hard disk

300GB, 450GB, 600GB

15,000rpm

 

Serial Attached

 

 

 

Nearline SAS disks

Hard disk

1TB, 2TB, 3TB, 4TB

7,200rpm

 

SCSI (6Gbit/s)

 

 

 

SSDs

Flash memory

100GB, 200GB, 400GB,

 

 

 

 

800GB

 

 

 

 

 

 

1.5Power Distribution Units (Only for Regions Other than EMEA&I)

There are two sizes for power distribution units: 1U and 2U.

A power distribution unit is an option to connect power supply units to power outlets when power sockets are limited.

Power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 1U, Max 2 enclosures connection)

There are four outlets and two inlets.

Figure 1.23 Power distribution unit (AC200-240V, 1U, Max 2 enclosures connection)

Outlets (OUTPUT)

Inlets (INPUT)

24

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

Copyright 2013 FUJITSU LIMITED

P3AM-4822-12ENZ0

Loading...
+ 56 hidden pages