Frigidaire FRS26HR4AB1, FRS26R4AW2, FRS26R4AB2, FRS23R4AB3, FRS26R4AQ3 User Manual
...
P/N 240389303 (0110)
Welcome & Congratulations
Congratulations on your purchase of a new refrigerator! We here at Electrolux Home Products are very proud of our product and we are completely committed to providing you with the best service possible. Your satisfaction is our #1 priority.
Please read this Use & Care Manual very carefully. It contains valuable information on how to properly maintain your new refrigerator.
We know you’ll enjoy your new refrigerator and Thank You for choosing our product. We hope you consider us for future purchases.
PLEASE READ AND SAVE THESE INSTRUCTIONS
This Use & Care Manual provides specific operating instructions for your model. Use your refrigerator only as instructed in this manual. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating and maintaining any appliance.
Please record your model and serial numbers below for future reference. This information is found on the serial plate located inside the refrigerator compartment.
NOTE: Use only soap and water to clean serial plate.
Model Number:
Serial Number:
Purchase Date:
Questions?
1-800-944-9044
(United States)
1-866-213-9397
(Canada)
Extend Your Warranty Protection
With An
Extended Service Contract
CALL 1-800-944-9044
To Enjoy These Benefits:
•Total freedom from repair bills so unexpected repairs won’t upset your budget.
•Fast, convenient toll-free service is just a phone call away.
•Top-quality repairs by factory-trained experts.
•Quick access to genuine replacement parts so you can rest assured your refrigerator is repaired with the proper components.
S erial Plate
Please complete and mail in the Product Registration Card included with your refrigerator.
2
Please attach sales receipt here for future reference.
Important Safety Instructions
WARNING: Please Read All Instructions Before Using This Refrigerator.
FOR YOUR SAFETY
•Do not store or use gasoline, or other flammable liquids in the vicinity of this or any other appliance. Read product labels for warnings regarding flammability and other hazards.
•Do not operate the refrigerator in the presence of explosive fumes.
•Avoid contact with any moving parts of automatic ice maker.
•Remove all staples from the carton. Staples can cause severe cuts, and also destroy finishes if they come in contact with other appliances or furniture.
CHILD SAFETY
Destroy or recycle the carton, plastic bags, and any exterior wrapping material immediately after the refrigerator is unpacked. Children should NEVER use these items to play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers, and can quickly cause suffocation.
PROPER DISPOSAL OF YOUR REFRIGERATOR OR FREEZER
Risk of child entrapment
Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators or freezers are still dangerous – even if they will sit for “just a few days.” If you are getting rid of your old refrigerator or freezer, please follow the instructions below to help prevent accidents.
Before you throw away your old refrigerator/ freezer:
•Remove doors.
•Leave shelves in place so children may not easily climb inside.
•Have refrigerant removed by a qualified service technician.
These Guidelines Must Be Followed To Ensure That Safety Mechanisms In This Refrigerator Will Operate Properly.
ELECTRICAL INFORMATION
•The refrigerator must be plugged into its own dedicated 115 Volt, 60 Hz., AC only electric outlet.
The power cord of the appliance is equipped with a three-prong grounding plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded three-prong receptacle. The receptacle must be installed in accordance with local codes and ordinances. Consult a qualified electrician.
Do not use an extension cord or adapter plug.
•Immediately repair or replace any power cord that becomes frayed or damaged.
•Never unplug the refrigerator by pulling on the power cord. Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord.
•Unplug the refrigerator before cleaning and before replacing a light bulb to avoid electrical shock.
•Performance may be affected if the voltage varies by 10% or more. Operating the refrigerator with insufficient power can damage the compressor. Such damage is not covered under your warranty.
•Do not plug the unit into an outlet controlled by a wall switch or pull cord to prevent the refrigerator from being turned off accidentally.
NOTE: Turning the freezer temperature control to OFF turns off the compressor, but does not disconnect electrical power to the light bulb or other electrical components.
•Avoid connecting refrigerator to a Ground Fault Interruptor (GFI) circuit.
3
Installation
This Owner’s Guide provides specific operating instructions for your model. Use the refrigerator only as instructed in this Use & Care Manual. Before starting the refrigerator, follow these important first steps.
LOCATION
•Choose a place that is near a grounded electrical outlet. Do Not use an extension cord or an adapter plug.
•If possible, place the refrigerator out of direct sunlight and away from the range, dishwasher or other heat sources.
•The refrigerator must be installed on a floor that is level and strong enough to support a fully loaded refrigerator.
•Consider water supply availability for models equipped with an automatic ice maker.
INSTALLATION
•Do Not install the refrigerator where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the refrigerator.
Do Not block the toe grille on the lower front of your refrigerator. Sufficient air circulation is essential for the proper operation of your refrigerator.
Installation Clearances
•Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections:
Sides & Top --------------- |
3/8” |
Back ------------------------ |
1” |
DOOR OPENING
NOTE: If you refrigerator is placed with the door hinge side against a wall, you may have to allow additional space so the door can be opened wider.
Your refrigerator should be positioned to allow easy access to a counter when removing food. For best use of drawers and freezer baskets, the refrigerator should be in a position where both the refrigerator and freezer doors can be fully opened.
TOE GRILLE INSTALLATION / REMOVAL
To Remove Toe Grille:
1.Open freezer and fresh food compartment doors.
2.Working from left side of toe grille, slip your fingers between top of toe grille and cabinet. Gently pull forward until first set of tabs are free. Slide your hand down past the free tabs and pull forward again until the second set of tabs are free. Continue this process until all tabs are free and the toe grille can be removed. (See graphic at top of page in right column.)
To Install Toe Grille:
1.Open freezer and fresh food compartment doors.
2.Line up toe grille at
base of refrigerator, making sure the four bottom tabs are resting through holes at base of cabinet.
3.Starting from left side
of toe grille, press in on first top tab using your thumb and push toe grille forward until it snaps in place. Continue this process until all tabs aresnapped in place and toe grille is secured to refrigerator.
LEVELING
All four corners of your refrigerator must rest firmly on a solid floor. Your refrigerator is equipped with adjustable front rollers to help level your unit.
To Level Your Refrigerator:
1.Remove toe grille. (See “To Remove Toe Grille” above.)
2.Use flat-blade screwdriver or 3/8” socket wrench to adjust front rollers.
NOTE: The refrigerator doors are designed to shut by themselves within a 20 degree opening.
3.Check both doors to be sure seals touch cabinet on all four sides.
4
Installation - Connecting Ice Maker To Water Supply
To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator.
To Avoid Property Damage:
•Copper tubing is recommended for the water supply line. Water supply tubing made of ¼” plastic is not recommended since it greatly increases the potential for water leaks. Manufacturer will not be responsible for any damage if plastic tubing is used for supply line.
•DO NOT install water supply tubing in areas where temperatures fall below freezing.
•Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.
IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.
Before Installing The Water Supply Line, You Will Need
•Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver
•Access to a household cold water line with water pressure between 20 and 100 psi.
•A water supply line made of ¼ inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed, you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).
•A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve.
•A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.
NOTE: Water line kit number 5303917950, available from your appliance dealer at additional cost, contains 25 feet (7.6 meters) of ¼ inch OD copper tubing, a saddle type shutoff valve (nonpiercing), (2) ¼ inch brass compression nuts, (2) ferrules/sleeves, and instructions for installing a water supply line.
To Connect Water Supply Line To Ice Maker Inlet Valve
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shut off valve.
3. Unscrew plastic cap from water valve inlet and discard cap.
4. Slide brass compression nut, then ferrule (sleeve) onto water supply line, as shown.
5. Push water supply line into water valve inlet as far as it will go (¼ inch). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten.
6. With steel clamp and screw, secure water supply line to rear panel of refrigerator as shown.
7.Coil excess water supply line (about 2½ turns) behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.
8. Turn ON water supply at shutoff valve and tighten any connections that leak.
9. Reconnect refrigerator to electrical power source.
10. To turn ice maker on, lower wire signal arm (see ice maker front cover for ON/OFF position of arm).
IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Air in new plumbing lines may cause ice maker to cycle two or three times before making a full tray of ice. New plumbing may cause ice to be discolored or have poor flavor. Discard ice made during the first 24 hours.
5
Door Removal Instructions
DOOR REMOVAL INSTRUCTIONS:
If it is necessary to move the refrigerator through narrow doorways, follow these steps to remove the doors.
IMPORTANT: Before you begin, turn freezer temperature control to OFF and remove electrical power cord from wall outlet. Remove any food from door shelves.
1.Disconnect electrical supply.
2.Open both doors, then remove toe grille.
3.Close doors.
To Remove Refrigerator Door:
1.Remove top hinge cover screw on refrigerator door and remove cover.
2.Trace around hinge with soft lead pencil. This will make it easier to realign doors when they are replaced.
3.Remove top hinge and lift refrigerator door off bottom hinge pin. Set door aside.
4.Remove bottom hinge, if necessary.
5.Reverse this procedure to reinstall refrigerator door.
To Remove Freezer Door:
1. Disconnect water line coming from lower hinge of freezer door at connection located under front of freezer: grip water tube firmly in one hand, then with 3/8” wrench or fingers, push in on gray collar to release water connector.
2.Remove top hinge cover screw on freezer door and remove cover.
3.Disconnect wiring harness connector plug at top hinge: place your thumbs on flat sides of each connector and bend both parts back and forth, then with firm grasp, pull both pieces apart.
4.Trace around hinge with soft lead pencil. This will make it easier to
realign doors when they are replaced.
5. Remove top hinge,allowing wiring harness to pull through hinge and lift freezer door off of bottom hinge pin. Lay door down flat to avoid kinking water line.
6. Remove bottom hinge, if necessary.
7. Reverse this procedure to reinstall freezer door.
When both doors have been reinstalled, replace toe grille and plug in electrical power cord. Turn both temperature controls to center position. Adjust settings as necessary.
6
Features At A Glance
Features may vary according to model
7
Temperature Controls
COOL DOWN PERIOD
To ensure safe food storage, allow the refrigerator to operate with the doors closed for at least 8 to 12 hours before loading it with food.
REFRIGERATOR & FREEZER CONTROLS
NOTE: When first turning refrigerator on, move refrigerator cold control to ▼which is the recommended initial setting. After 24 hours, adjust the controls as needed.
TEMPERATURE ADJUSTMENT
• After 24 hours, adjust the controls as needed. Adjust temperatures gradually: move the knob in small increments, allowing the temperature to stabilize.
• For colder temperatures, turn the knob towards Colder. |
|
• For warmer temperatures, turn the knob towards Warmer. |
|
To maintain temperatures, a fan circulates air in the |
|
refrigerator and freezer compartments. For good circulation, |
|
do not block cold air vents with food items. |
Refrigerator & Freezer Controls |
|
IMPORTANT: Turning the freezer temperature control to “Off” turns off the compressor, but does not disconnect the power to the light bulb and other electrical components.
TEMPERATURE ADJUSTMENT GUIDE
If Fresh Food Compartment Is Too Warm |
Turn Fresh Food Control Slightly Towards Cold. |
|
|
If Fresh Food Compartment Is Too Cold |
Turn Fresh Food Control Slightly Towards Warm. |
|
|
If Freezer Compartment Is Too Warm |
Turn Freezer Control Slightly Towards Cold. |
|
|
If Freezer Compartment Is Too Cold |
Turn Freezer Control Slightly Towards Warm. |
|
|
To Turn Refrigerator Off |
Turn Freezer Control To Off. |
|
|
8
Looking Inside
PIZZA SHELF (SOME MODELS)
This shelf is attached to the freezer wall beside the ice dispenser container. This convenient area allows for storage of pizza and other tall items placed vertically between the ice dispenser container and the freezer wall.
ICE CREAM SHELF (SOME MODELS)
This shelf attaches to the top of the ice dispenser container. It allows storage of both round and rectangular cartons of your favorite ice cream.
TIP-UP SHELF (SOME MODELS)
A Tip-Up shelf in the freezer section allows tall items to be easily stored.
To avoid personal injury or property damage, handle tempered glass shelves carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change.
CANTILEVER SHELF ADJUSTMENT
Refrigerator shelves are easily adjusted to suit individual needs. Before adjusting the shelves, remove all food. Cantilever shelves are supported at the back of the refrigerator.
To adjust cantilever shelves:
1Lift front edge up.
2Pull shelf out.
Replace the shelf by inserting the hooks at rear of the shelf into the wall bracket. Lower the shelf into the desired slots and lock into position.
Pizza Shelf |
Ice Cream Shelf |
SpillSafeTM glass shelves (some models) catch and hold accidental spills. In some models, the SpillSafeTM shelves slide out for easy access to food and for fast cleaning. The shelves slide out independently of their mounting brackets. Just pull the front of the shelf forward. Shelves can be extended as far as the stopper will allow but are not removable from their mounting brackets.
1
2
1
2
Cantilever Glass Shelf |
Cantilever Sliding Glass Shelf |
9
Looking Inside (continued)
DOOR STORAGE |
TALL BOTTLE RETAINER (SOME MODELS) |
Door bins and shelves are provided for convenient storage of jars, bottles, and cans. Frequently used items can be quickly selected.
Some models have door bins that can accommodate gallonsized plastic drink containers and economy-sized jars and containers. Some bins are adjustable for maximum storage capacity.
The dairy compartment, which is warmer than the general food storage section, is intended for short term storage of cheese, spreads, or butter.
The Tall Bottle Retainer keeps tall containers in the bin from falling forward when opening or closing the refrigerator door. To install, hold the retainer at the top, and slide it over the outside wall of the bin, as shown in the diagram. The Tall Bottle Retainer works best with a Bin Snugger.
Fixed Door Bin
ADJUSTABLE DOOR BINS
Some models have adjustable door bins that can be moved to suit individual needs.
To move door bins
1.Lift bin straight up.
2.Remove bin.
3.Place bin in desired position.
4.Lower bin onto supports until locked in place.
Tall Bottle Retainer (left) and Bin Snugger (right)
SPECIAL ITEM RACK (SOME MODELS)
The innovative design of the Special Item Rack allows you to store a six-pack of 12 ounce drink cans, a bottle of wine, a two-liter soft drink bottle, or a carton of eggs. The Special Item Rack mounts on the left side of your refrigerator. To install, just slide the Special Item Rack onto any shelf as shown in the drawing.
Special ItemRack
Adjustable Door Bin
10
Looking Inside - Special Storage Areas
CRISPERS (SOME MODELS)
The crispers, located under the bottom refrigerator shelf, are designed for storing fruits, vegetables, and other fresh produce. Wash items in clear water and remove excess water before placing them in the crispers. Items with strong odors or high moisture content should be wrapped before storing.
Crisper Drawer
HUMIDITY CONTROL (SOME MODELS)
The Humidity Control, present on some models with crisper drawers, allows you to adjust the humidity within the crisper. This can extend the life of fresh vegetables that keep best in high humidity.
NOTE: Leafy vegetables keep best when stored with the Humidity Control set on Higher Humidity, or in a drawer without a Humidity Control. This keeps incoming air to a minimum and maintains maximum moisture content.
Crisper Humidity Control
DELI DRAWER (SOME MODELS)
Some models are equipped with a Deli Drawer for storage of luncheon meats, spreads, cheeses, and other deli items.
MEAT KEEPER (SOME MODELS)
Some models are equipped with a Meat Keeper. Meat Keeper temperatures can be adjusted by sliding the Meat Keeper Temperature Control in either direction. Use this pan for short term storage of bulk meat items. If meats are to be kept longer than one or two days, they should be frozen. The Meat Keeper is fixed and cannot be moved up or down. If fruits or vegetables are to be stored in the Meat Keeper, set the Meat Keeper Temperature Control to a warmer setting to prevent freezing.
Meat Keeper with Temperature Control
WINE RACK (SOME MODELS)
The wine rack stores bottles of wine, or single two-liter plastic bottles of juice or soda pop. To install, slide the Wine Rack onto the shelf with the curve facing in. To remove, slide the Wine Rack out. Install on either side of shelf.
Wine Rack
11
Automatic Ice and Water Dispenser
ICE AND WATER DISPENSER FEATURES
The ice and water dispenser conveniently dispenses chilled water, and ice cubes or crushed ice, depending on the model. Some models have an Extra Ice feature that increases ice production for special occasions such as parties.
To operate the ice dispenser, select the ice option desired using the touchpad. Press a glass against the dispensing paddle as far up as possible to catch all ice. To stop dispensing ice, pull glass away from dispensing paddle. Do not remove the glass until the ice has completely dispensed. (Complete instructions for the dispenser operation are attached to the inside of the freezer door.)
To operate the water dispenser, press a glass against the dispensing paddle. To stop dispensing water, pull glass away from dispensing paddle. A drip tray located at the base of the dispenser, catches small spills and allows them to evaporate. This drip tray is removable and dishwasher safe. Do not pour water or excess cubes into this area because there is no drain.
Dispenser Light (some models)
The dispenser has a light which can be turned on and off by pressing the Light touchpad. The light also turns on automatically when ice and/or water is dispensed. Replace light bulb with an appliance bulb of the same wattage.
OFF
Wire
Signal Arm
Ice and Water Dispenser Panel (features may vary according to model)
How the Water Dispenser Works
The water tank, located behind the drawers in the refrigerator compartment, automatically fills as water is dispensed. For proper dispenser operation, the recommended supply water pressure should fall between 20 psi and 100 psi.
After the refrigerator is connected to the water supply, fill the water tank by drawing one glass of water. It may take about 1½ minutes after activating the dispenser paddle before water begins to fill this first glass. Continue flushing the system for 3 minutes to rid the tank and plumbing connections of any impurities. The water dispenser has a built in shutoff device that will stop the water flow after 3 minutes of continuous use. Simply release the dispenser paddle to reset the shutoff mechanism.
Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.
How the Ice Dispenser Works
The ice maker and container are located in the top of the freezer compartment. After the refrigerator is installed properly and has cooled for several hours, the ice maker can begin making ice within 24 hours. Air in new plumbing lines may cause the ice maker to cycle two or three times before making a full tray of ice. To begin ice production, lower the wire signal arm to the "down" or ON position. With no usage it will take approximately 2 days to fill the ice container. The ice maker turns off automatically when the ice container becomes full. To stop the ice maker, lift the wire signal arm until it clicks, and locks in the "up" or OFF position.
Because of new plumbing connections, the first production of ice cubes may be discolored or have an odd flavor. These should be discarded until the cubes made are free of discoloration and taste.
12
Automatic Ice and Water Dispenser
ICE DISPENSER TIPS
•Ice cubes stored too long may develop an odd flavor. Empty the ice container and ensure that the wire signal arm is in its “down” or ON position. The ice maker will then produce more ice.
•Occasionally shake the ice container to keep ice separated.
•Keep the wire signal arm in its “up” or OFF position until the refrigerator is connected to the water supply or whenever the water supply is turned off.
If the dispensing paddle is pushed for more than 4 minutes, the dispenser motor may overload and stop. The overload protector will reset automatically after 3 or 4 minutes.
•If a large quantity of ice is needed at one time, it is best to remove cubes directly from the ice container.
•The following sounds are normal when the ice maker is operating:
•Motor running
•Ice loosening from tray
•Ice dropping into ice container
•Running water
•Water valve opening or closing
•Stop the ice maker when cleaning the freezer and during vacations.
•If the ice maker will be turned off for a long period of time, turn the water supply valve to the closed position.
Do not use the ice chute as a handle when removing or replacing the ice storage bin. Surfaces there may be sharp.
Do not put fingers up ice chute. Surfaces there may be sharp.
CLEANING THE ICE DISPENSER
Clean the dispenser and ice container at regular intervals, particularly before you take a vacation or move, or if the ice dispenser sticks.
1.Stop ice production by lifting the wire signal arm to the "up" or OFF position.
2.Remove ice container by lifting up and out. Empty and carefully clean the container with mild detergent. Rinse with clear water. Do not use harsh or abrasive cleaners. Allow ice container to dry completely before replacing in the freezer.
3.Remove ice chips and clean the shelf and chute that supports the ice container.
4.Replace the ice container. Lower the wire signal arm on the ice maker to the "down" or ON position and the ice maker will resume production.
IMPORTANT: When removing or replacing the ice bin, do not rotate the auger in the ice bin. If the auger is accidentally turned, you must realign the auger by turning it in 90° turns until the ice bin fits into place with the drive mechanism. For further instruction, see the label on the ice bucket.
Remove and empty the ice storage bin if:
1.An extended power failure (one hour or longer) causes ice cubes in the ice storage bin to melt and freeze together and jam the dispenser mechanism.
2.The ice dispenser is not used frequently. Ice cubes will freeze together in the bin and jam the dispenser mechanism. Remove the ice storage bin and shake to loosen the cubes.
NEVER use an ice pick or similar sharp instrument to break up the ice. This could damage the ice storage bin and dispenser mechanism.
13
Automatic Ice and Water Dispenser
PureSource TM * Ice and Water Filter (some models)
NOTE: If you purchased a refrigerator with a PureSource TM * Ice and Water filter, please read the following use and care information. This ice and water filter system filters water to your ice maker and water dispenser. It is located in the upper right back corner of the fresh food compartment.
Order new filter cartridges through the dealer where you bought the refrigerator, or contact the Consumer Assistance Center at 1-800-944-9044. It might be good to order some filter cartridges when you first install your refrigerator. Be sure to ask for the RG-100 PureSource ™* replacement cartridge.
The PureSource™ * NGRG-
2000 Ice and Water Filter System with the RG-100 cartridge is tested and certified by NSF International,
the nationally recognized and respected, not for profit, certification organization for public health safety. The PureSource™* system is tested and certified to ANSI/NSF Standard 42. See performance data sheet for specifications. This system should not be used on water that is microbiologically unsafe or with water of unknown quality unless the water has been adequately disinfected before or after traveling through the filtration system.
•Rated Capacity - 400 gallons
•Rated service flow - .5 GPM
•Maximum Rated Pressure - 100 PSI
•Maximum Operating Temp. - 100° F
1.Open freezer door and leave open until filter change is complete.
2.Set ice maker wire signal arm to the OFF (up) position (See illustration on page 12).
3.Hold filter cup firmly, and unscrew towards left (Some water could
leak out as you remove cup. This is normal.). Filter cartridge should come down with cup. If cartridge remains in housing, pull down gently, while twisting filter back and forth.
4.Rinse out cup under running water.
5.The large o-ring that seals the filter system sets in the o-ring groove down inside the cup. Should the o-ring fall out during filter cartridge replacement, simply place it back in the groove prior to screwing the cup back in place. If the o-ring becomes damaged, you will need to order one from the Consumer Assistance Center.
6.Discard old filter cartridge.
7.Remove new filter cartridge from packaging and place in cup. The end with the small o-ring should be up, out of the cup.
8.Screw cup, with filter, back onto housing. Do Not Use Wrench To Reinstall Cup. Filter cartridge will self-align as cup is tightened. Be sure cup is completely tightened with PureSource™ logo facing outward. Do Not
Tighten Past Stop.
9.Set ice maker wire signal arm to the ON (down) position.
10.Check for leaks. Open refrigerator door. Wipe any water droplets from the filter cup. Fill a glass with water. If there is a leak, unscrew filter cup, and reinsert the filter cartridge. Check placement of large O-ring. Reinstall filter cup, making certain it is tightened completely.
11.To condition filter system and purge air from water line, fill a glass with water. Continue flushing the system for 30 seconds to assure that the purest water possible is stored in water tank.
IMPORTANT: Resetting The Filter Status Light (some models)
After replacing the filter cartridge, it will be necessary to press the Filter Status reset button located on the ice and water dispenser. This will reset the Filter Status light. Push the reset button until the green light flashes (3-15 seconds). Please refer to the complete dispenser operating instructions attached to the inside of the freezer door.
On models without a Filter Status reset button, there is a set of Reminder Stickers included in the plastic bag that the Use & Care Manual came in. Choose a dated sticker that indicates 6 - 9 months (depending on your water quality and usage) from the date of installation. Place the sticker on the front of the filter cup to remind you when it is time to change the filter.
* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter
14
Automatic Ice and Water Dispenser
PureSource2TM * Ice and Water Front Filter (some models)
NOTE: If you purchased a refrigerator with a PureSource2TM * Ice and Water front filter, please read the following use and care information. This ice and water filter system filters water to your ice maker and water dispenser. It is located in the upper right front corner of the fresh food compartment.
System Startup:
Water supply does not need to be turned off, however, do not use ice and water dispenser while installing filter.
The filter cartridge has already been installed in the filter housing at the factory. Refer to the How The Water Dispenser Works section to properly fill the system with water.
Order new filter cartridges through the dealer where you bought the refrigerator, or contact the Consumer Assistance Center at 1-800-944-9044. It might be good to order some filter cartridges when you first install your refrigerator. Be sure to ask for the PureSource2TM * replacement cartridge.
The PureSource2TM* Ice and
Water Filter System NGFC 2000 with the PureSource2TM* cartridge FC 100 is tested and certified by NSF International,
the nationally recognized and respected, not for profit, certification organization for public health safety. The PureSource2TM* Filter system is tested and certified to ANSI/ NSF Standards 42 and 53. See performance data sheet for specifications. This system should not be used on water that is microbiologically unsafe or with water of unknown quality unless the water has been adequately disinfected before or after traveling through the filtration system.
•Rated Capacity - 400 gallons
•Rated service flow - .5 GPM
•Maximum Rated Pressure - 100 PSI
•Maximum Operating Temp. - 100° F
Changing the Filter:
Water conditions vary throughout the world, but changing the water filter every 6 - 9 months normally will ensure the highest possible water quality. The Filter Status light will turn red after approximately 400 gallons of water has flowed through the ice and water dispenser. Also, if the filter has been in a refrigerator that has not been in use for awhile (during moving for example), change the filter before reinstalling the refrigerator. The dispenser system will also operate without filtration (with filter cartridge removed and bypass installed).
To change filter:
It is not necessary to turn the water supply off to change the filter.
1.Set ice maker wire signal arm to the OFF (up) position (See illustration on page 12).
2.Push the Filter Release Button, located to the right of the filter cartridge, to release the filter from the housing. To minimize the possibility of the filter falling out of the housing during removal, it would be best to hold the filter as it moves out toward you.
NOTE: A small amount of water may be released during this operation. You should have a paper towel or dish cloth handy to wipe up any water that may drip out of the filter or housing. Two small holes near the back of the housing have been added for any excess water to escape. It would be best to clear away any food near this area on the top shelf in advance of removing the filter.
3.Pull the old filter cartridge straight out of the housing.
4.Discard the old filter.
5.Remove the new filter cartridge from the packaging and insert into the filter housing the same way the old one came out.
6.When the cartridge is almost in, you will feel it stop against the clip assembly in the back of the housing. The clip assembly holds the filter cartridge firmly in place. At this point, you will need to push firmly until the cartridge snaps fully in place. When completely in place, the front of the filter cartridge will be flush with the front of the housing.
7.Set the ice maker wire signal arm to the ON (down) position.
8.Fill a glass with water. As you are doing this, check for leaks at the filter housing. There will be noticable spurts and sputters as the system pushes the air out through the system and out the dispenser nozzle. This is normal.
9.After you have run one glass of water, continue to flush the system for approximately 3 minutes to assure that the purest water possible is stored in the water storage tank.
IMPORTANT: Resetting The Filter Status Light (some models)
After replacing the filter cartridge, it will be necessary to press the Filter Reset button located on the ice and water dispenser. This will reset the Filter Status light. Push the reset button until the green light flashes (3-15 seconds). Please refer to the complete dispenser operating instructions attached to the inside of the freezer door.
* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter
15
Food Storage & Energy Saving Ideas
FOOD STORAGE IDEAS
Fresh Food Storage
•The fresh food compartment should be kept between 34° F and 40° F with an optimum temperature of 37° F.
•Avoid overcrowding the refrigerator shelves. This reduces the circulation of air around the food and results in uneven cooling.
Fruits and Vegetables
•Storage in the crisper drawers traps moisture to help preserve the fruit and vegetable quality for longer time periods.
Meat
•Raw meat and poultry should be wrapped securely so leakage and contamination of other foods or surfaces does not occur.
Frozen Food Storage
•The freezer compartment should be kept at 0° F or lower.
•A freezer operates most efficiently when it is at least 2/3 full.
Packaging Foods for Freezing
•To minimize dehydration and quality deterioration, use aluminum foil, freezer wrap, freezer bags or airtight containers. Force as much air out of the packages as possible and seal them tightly. Trapped air can cause food to dry out, change color, and develop an off-flavor (freezer burn).
•Wrap fresh meats and poultry with suitable freezer wrap prior to freezing.
•Do not refreeze meat that has completely thawed.
Loading the Freezer
•Avoid adding too much warm food to the freezer at one time. This overloads the freezer, slows the rate of freezing, and can raise the temperature of frozen foods.
•Leave a space between the packages, so cold air can circulate freely, allowing food to freeze as quickly as possible.
•Avoid storing hard-to-freeze foods such as ice cream and orange juice on the freezer door shelves. These foods are best stored in the freezer interior where the temperature varies less.
ENERGY SAVING IDEAS
•Locate the refrigerator in the coolest part of the room, out of direct sunlight, and away from heating ducts or registers. Do not place the refrigerator next to heat-producing appliances such as a range, oven, or dishwasher. If this is not possible, a section of cabinetry or an added layer of insulation between the two appliances will help the refrigerator operate more efficiently.
•Level the refrigerator so that the doors close tightly.
•Refer to this Use & Care Manual for the suggested temperature control settings.
•Periodic cleaning of the condenser will help the refrigerator run more efficiently. See the Care and Cleaning Chart on page 17.
•Do not overcrowd the refrigerator or block cold air vents. Doing so causes the refrigerator to run longer and use more energy.
•Cover foods and wipe containers dry before placing them in the refrigerator. This cuts down on moisture build-up inside the unit.
•Organize the refrigerator to reduce door openings. Remove as many items as needed at one time and close the door as soon as possible.
16
Normal Operating Sounds & Sights
UNDERSTANDING THE SOUNDS YOU MAY HEAR
Your new high-efficiency refrigerator may make unfamiliar sounds. Don’t be alarmed, these are all normal sounds. Hard surfaces, such as vinyl or wood floors, walls, and kitchen cabinets may make sounds more noticeable. Listed below are descriptions of some of the most common sounds you may hear, and what is causing them.
NOTE: Rigid foam insulation is very energy efficient, but is not a sound insulator.
A. Evaporator
The flow of refrigerant through the evaporator may create a boiling or gurgling sound.
B. Evaporator Fan
You may hear air being forced through the refrigerator by the evaporator fan.
C.Defrost Heater
During defrost cycles, water dripping onto the defrost heater may cause a hissing or sizzling sound. After defrosting, a popping sound may occur.
IMPORTANT: During the automatic defrost cycle, you may notice a red glow in the vents on the back wall of your freezer compartment. This is normal during the defrost cycle.
D. Automatic Ice Maker
If your refrigerator is equipped with an automatic ice maker, you will hear ice cubes falling into the ice bin.
E. Cold Control & Defrost Timer
These parts can produce a snapping or clicking sound when turning the refrigerator on and off. The timer also produces sounds similar to an electric clock.
F. Condenser Fan
You may hear air being forced through the condenser by the condenser fan.
G.Compressor
Modern, high-efficiency compressors operate much faster than older models. The compressor may have a high-pitched hum or pulsating sound.
H.Water Valve
If your refrigerator is equipped with an automatic ice maker, you will hear a buzzing sound as the water valve opens to fill the ice maker during each cycle.
I.Drain Pan
You may hear water running into the drain pan during the defrost cycle.
J.Condenser
17
Care & Cleaning
Keep your refrigerator and freezer clean to prevent odor build-up. Wipe up any spills immediately and clean both sections at least twice a year. Never use metallic scouring pads, brushes, abrasive cleaners or strong alkaline solutions on any surface. Do not wash any removable parts in a dishwasher. Always unplug the electrical power cord from the wall outlet before cleaning.
CAUTION: 
•When moving the refrigerator, pull straight out. Do not shift the refrigerator from side to side as this may damage the floor. Be careful not to move the refrigerator beyond the plumbing connections.
•Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or damp hands.
•To avoid damage and help the refrigerator run as efficiently as possible, clean the condenser periodically.
NOTES:
•Turning the freezer temperature control to OFF turns off the compressor, but does not disconnect electrical power to the light bulb or other electrical components.
•Do not use razor blades or other sharp instruments which can scratch the appliance surface when removing adhesive labels. Any glue left from tape or labels can be removed with a mixture of warm water and mild detergent, or, touch the glue residue with the sticky side of tape you have already removed. Do not remove the serial plate.
Care & Cleaning Chart
Part
Interior/Door
Liner
Door Gaskets
Drawers/Bins
Glass
Shelves
Toe Grille
Exterior and
Handles
Exterior and Handles (Stainless Steel Models Only)
Condenser
Coils
Cleaning Agents
•Soap and water
•Baking soda and water
•Soap and water
•Soap and water
•Soap and water
•Glass cleaner
•Mild liquid sprays
•Soap and water
•Mild liquid sprays
•Vacuum attachment
•Soap and water
•Soap and water
•Ammonia
•Stainless Steel Cleaners
•Vacuum attachment
Tips and Precautions
Use 2 tablespoons of baking soda in 1 quart of warm water. Be sure to wring excess water out of sponge or cloth before cleaning around controls, light bulb or any electrical part.
Wipe gaskets with a clean soft cloth.
Do not wash any removable items (bins, drawers, etc.) in dishwasher.
Allow glass to warm to room temperature before immersing in warm water.
Vacuum dust from front of toe grille. Remove toe grille (See illustration on page 5). Vacuum backside and wipe with sudsy cloth or sponge. Rinse and dry.
Do not use commercial household cleaners, ammonia, or alcohol to clean handles.
Clean stainless steel front and handles with non-abrasive soapy water and a dishcloth. Rinse with clean water and a soft cloth. Wipe stubborn spots with an ammonia-soaked paper towel, and rinse. Use a non-abrasive stainless steel cleaner. These cleaners can be purchased at most home improvement or major department stores. Always follow manufacturer's instruction.
NOTE: Always, clean, wipe and dry with the grain to prevent cross-grain scratching. Wash the rest of the cabinet with warm water and mild liquid detergent. Rinse well, and wipe dry with a clean soft cloth.
Use the dusting tool attachment on your vacuum to remove dust build-up on the condenser coils (see item “J” in illustration on page 17 for location).
18
Care & Cleaning (continued)
Wear gloves when replacing light bulbs to avoid getting cut.
REPLACING LIGHT BULBS
1.Unplug refrigerator.
2.Wear gloves as protection against possible broken glass.
3.Remove light cover, if necessary.
4.Unscrew and replace old bulb with an appliance bulb of the same wattage.
5.Replace light cover, if necessary.
6.Remember to plug the refrigerator back in.
Crisper Light Replacement (Some Models)
Refrigerator Light Replacement
Freezer Light Replacement
Short
Vacations
Long
Vacations
Moving
Vacation and Moving Tips
• Leave refrigerator operating during vacations of 3 weeks or less.
• Use all perishable items from refrigerator compartment.
• Turn automatic ice maker off, even if you will only be gone for a few days.
• Remove all food and ice if you will be gone one month or more.
• Turn controls to OFF and disconnect power.
• Turn off automatic ice maker and turn water supply valve to closed position.
• Clean interior thoroughly.
• Leave both doors open to prevent odors and mold build-up. Block doors open if necessary.
• Remove all food and ice.
• If using handcart, load from side.
• Adjust rollers all the way up to protect them during sliding or moving.
• Pad cabinet to avoid scratching surface.
IMPORTANT: If the refrigerator is going to be stored or moved in freezing temperatures, the water in the ice and water system must be drained completely. Failure to do so could result in water leaks when the refrigerator is put back into service. Contact a service representative to perform this operation.
19
Warranty Information
REFRIGERATOR WARRANTY
Your refrigerator is protected by this warranty
|
WARRANTY |
THROUGH OUR AUTHORIZED SERVICERS, |
THE CONSUMER WILL BE RESPONSIBLE FOR: |
|
PERIOD |
WE WILL: |
|
|
|
||
|
|
|
|
FULL ONE-YEAR |
One year from original |
Pay all costs for repairing or replacing any parts of this |
Costs of service calls that are listed under NORMAL |
WARRANTY |
purchase date |
appliance which prove to be defective in materials or |
RESPONSIBILITIES OF THE CONSUMER. * |
|
|
workmanship. Excludes original and replacement Ice |
|
|
|
& Water filter cartridges (if equipped). Original and |
|
|
|
replacement cartridges are warranted for 30 days |
|
|
|
(parts only). |
|
|
|
|
|
LIMITED 2ND-5TH |
Second through fifth |
Repair or replace any parts in the cabinet liner or |
Costs for pick up and delivery of the appliance required because |
YEAR WARRANTY |
years from original |
Sealed Refrigeration System (compressor, condenser, |
of service. Costs for labor, parts and transportation other than |
(Cabinet Liner and |
purchase date |
evaporator, drier and tubing) which prove to be |
with respect to the cabinet liner or Sealed Refrigeration System. |
Sealed System) |
|
defective in materials or workmanship. |
|
|
|
|
|
LIMITED |
Time periods listed |
All of the provisions of the full warranties above and |
Costs of the technician's travel to the home and any costs for |
WARRANTY |
above. |
the exclusions listed below apply. |
pick up and delivery of the appliance required because of |
(Applicable to the |
|
|
service. |
State of Alaska) |
|
|
|
|
|
|
|
In the U.S.A., your appliance is warranted by Electrolux Home Products North America, a division of White Consolidated Industries Inc. We authorize no person to change or add to any of our obligations under this warranty. Our obligations for service and parts under this warranty must be performed by us or an authorized Electrolux Home Products North America servicer. In Canada, your appliance is warranted by WCI Canada Inc.
*NORMAL RESPONSIBILITIES OF THE CONSUMER
EXCLUSIONS
IF YOU NEED
SERVICE
This warranty applies only to products in ordinary household use, and the consumer is responsible for the items listed below:
1.Proper use of the appliance in accordance with instructions provided with the product.
2.Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in accordance with all local plumbing, electrical and/or gas codes.
3.Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections or defects in house wiring.
4.Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,etc., which are not a part of the appliance when it was shipped from the factory.
5.Damages to finish after installation.
6.Replacement of light bulbs and/or fluorescent tubes (on models with these features).
This warranty does not cover the following:
1.CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL
EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY. NOTE: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.
2.Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary household use. The consumer shall pay for such service calls.
3.Damages caused by services performed by servicers other than Electrolux Home Products North America or its authorized servicers; use of parts other than genuine Electrolux Home Products parts; obtained from persons other than such servicers; or external causes such as abuse, misuse, inadequate power supply or acts of God.
4.Products with original serial numbers that have been removed or altered and cannot be readily determined.
Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. This written warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service under this warranty must be obtained by contacting Electrolux Home Products:
This warranty only applies in the 50 states of the U.S.A., Puerto Rico, and Canada. Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by Electrolux Home Products North America, a division of White Consolidated Industries Inc. In Canada, your appliance is warranted by WCI Canada Inc.
|
01-U-RE-02 (Rev. 12/2000) |
|
|
USA |
Canada |
800•944•9044 |
866•213•9397 |
Electrolux Home Products North America |
Electrolux Home Products North America |
P.O. Box 212378 |
6150 McLaughlin Road |
Augusta, GA 30917 |
Mississauga, Ontario |
|
L5R 4C2 |
20
Before You Call
PROBLEM |
|
CAUSE |
|
CORRECTION |
RUNNING OF REFRIGERATOR |
|
|
||
Compressor does not run. |
• |
Freezer control is OFF. |
• |
Set freezer control. See Temperature Controls section. |
|
• |
Refrigerator is in defrost cycle. |
• |
This is normal for a fully automatic defrost refrigerator. |
|
|
|
|
The defrost cycle occurs periodically, lasting about 30 |
|
• |
|
• |
minutes. |
|
Plug at wall outlet is |
Ensure plug is tightly pushed into outlet. |
||
|
• |
disconnected. |
• |
|
|
House fuse blown or tripped |
Check/replace fuse with a 15 amp time-delay fuse. |
||
|
• |
circuit breaker. |
• |
Reset circuit breaker. |
|
Power outage. |
Check house lights. Call local Electric Company. |
||
Refrigerator runs too |
• |
Room or outside weather is |
• |
It’s normal for the refrigerator to work longer under |
much or too long. |
• |
hot. |
• |
these conditions. |
|
Refrigerator has recently been |
It takes 8-12 hours for the refrigerator to cool down |
||
|
|
disconnected for a period of |
|
completely. |
|
• |
time. |
• |
|
|
Automatic ice maker is |
Ice maker operation causes refrigerator to run slightly |
||
|
• |
operating. |
• |
more. |
|
Doors are opened too |
Warm air entering the refrigerator causes it to run |
||
|
• |
frequently or too long. |
• |
more. Open doors less often. |
|
Refrigerator/freezer door may |
Ensure refrigerator is level. Keep food and containers |
||
|
|
be slightly open. |
|
from blocking door. See PROBLEM section |
|
• |
|
• |
OPENING/CLOSING OF DOORS/DRAWERS. |
|
Freezer control is set too cold |
Set refrigerator control to warmer setting until |
||
|
|
(control found in refrigerator |
|
refrigerator temperature is satisfactory. Allow 24 hours |
|
• |
section). |
• |
for temperature to stabilize. |
|
Refrigerator/freezer gasket is |
Clean or change gasket. Leaks in door seal will cause |
||
|
|
dirty, worn, cracked, or poorly |
|
refrigerator to run longer in order to maintain desired |
|
• |
fitted. |
• |
temperatures. |
|
Condenser is dirty. |
Clean condenser. See Care & Cleaning Chart in Care |
||
|
|
|
|
and Cleaning section. |
Compressor goes off and |
• |
Thermostat keeps the |
• |
This is normal. Refrigerator goes on and off to keep |
on frequently. |
|
refrigerator at a constant |
|
temperature constant. |
|
|
temperature. |
|
|
|
|
|
|
|
TEMPERATURES ARE TOO COLD
Freezer temperature too cold. Refrigerator temperature is satisfactory.
Refrigerator temperature too cold. Freezer temperature is satisfactory.
Food stored in drawers freezes.
Food stored in Meat Keeper freezes (some models).
•Freezer control is set too cold.
•Refrigerator control is set too cold.
•Refrigerator control is set too cold.
•Meat Keeper Temperature Control set too cold.
•Set freezer control to a warmer setting. Allow 24 hours for temperature to stabilize.
•Set refrigerator control to a warmer setting. Allow 24 hours for temperature to stabilize.
•See solution above.
•Adjust Meat Keeper Temperature Control to a lower setting. (Meat should be stored at a temperature just below the freezing point for maximum fresh storage time. It is normal for ice crystals to form due to the moisture content of meat.)
21
Before You Call (continued)
PROBLEM |
CAUSE |
CORRECTION |
TEMPERATURES ARE TOO WARM
Freezer/Refrigerator |
• |
Doors are opened too |
temperature is too warm. |
• |
frequently or too long. |
|
Door is slightly open. |
|
|
• |
Condenser is dirty. |
|
|
|
Freezer temperature is too warm. Refrigerator temperature is satisfactory.
Refrigerator temperature is too warm. Freezer temperature is satisfactory.
Temperature in the Meat Keeper is too warm (some models).
•Freezer control is set too warm.
•Refrigerator control is set too warm.
•Meat Keeper Temperature Control is set too warm.
WATER/MOISTURE/FROST INSIDE REFRIGERATOR
Moisture collects on inside of refrigerator walls.
Water collects on bottom side of drawer cover.
•Weather is hot and humid.
•Door is slightly open.
•Door is opened too often or too long.
•Open containers.
•Vegetables contain and give off moisture.
Water collects in bottom of |
• |
Washed vegetables and fruit |
drawer. |
|
drain while in the drawer. |
WATER/MOISTURE/FROST OUTSIDE REFRIGERATOR
Moisture collects on |
• |
Weather is humid. |
outside of refrigerator or |
|
|
between doors. |
• |
Door is slightly open, causing |
|
|
cold air from inside refrigerator |
|
|
to meet warm air from outside. |
AUTOMATIC ICE MAKER
Ice maker is not making any ice.
•Ice maker wire signal arm is in the “up” or OFF position.
•Household water line valve is not open.
•Freezer is not cold enough.
•Saddle valve on cold water pipe is clogged or restricted by foreign material.
•Check to see if the water dispenser is dispensing water.
22
•Warm air enters the refrigerator whenever the door is opened. Open the door less often.
•See PROBLEM section OPENING/CLOSING OF DOORS/DRAWERS.
•Clean condenser. See Care & Cleaning Chart in Care and Cleaning section.
•Set freezer control to a colder setting. Allow 24 hours for temperature to stabilize.
•Set refrigerator control to a colder setting. Allow 24 hours for temperature to stabilize.
•Adjust Meat Keeper Temperature Control to a colder setting.
•The rate of frost buildup and internal sweating increases.
•See PROBLEM section OPENING/CLOSING OF DOORS/DRAWERS.
•Open door less often.
•Keep containers covered.
•It is not unusual to have moisture on the bottom side of the cover.
•Move humidity control (some models) to lower setting.
•Dry items before putting them in the drawer. Water collecting in bottom of drawer is normal.
•This is normal in humid weather. When humidity is lower, the moisture should disappear.
•See PROBLEM section OPENING/CLOSING OF DOORS/DRAWERS.
•Move wire signal arm to the “down” or ON position.
•Turn on household water line valve.
•See PROBLEM section TEMPERATURES ARE TOO WARM.
•Turn off household water line valve. Remove valve. Ensure that valve is not a self-piercing saddle valve. Clean valve. Replace valve if necessary.
•If not, the ice & water filter cartridge is clogged or restricted by foreign material, and must be replaced.
Before You Call (continued)
PROBLEM |
CAUSE |
CORRECTION |
AUTOMATIC ICE MAKER (CONTINUED)
Ice maker is not making enough ice.
Ice maker will not stop making ice.
Ice maker is not separating the ice cubes.
Ice has bad odor and taste.
ICE DISPENSER
Dispenser will not dispense ice.
Ice dispenser is jammed.
•Ice maker is producing less ice than you expect.
•Freezer is not cold enough.
•Household water line valve is not completely open.
•Check to see if water dispenser is dispensing slower than normal.
•Ice maker wire signal arm is being held down by some item in the freezer.
•Ice cubes are not being used frequently enough.
•Ice cubes are hollow or smaller than normal.
•Ice has picked up odor or flavor from strong food stored in refrigerator or freezer.
•Water running to ice maker has poor taste or odor.
•Ice not used frequently enough.
•Ice storage container is empty.
•Freezer temperature is set too warm.
•Household water line valve is not open.
•Freezer door is not closed.
•Ice dispensing arm has been held in for more than 4-5 minutes.
•Ice has melted and frozen around auger due to infrequent use, temperature fluctuations, and/or power outages.
•Ice cubes are jammed between ice maker and back of ice container.
•Ice cubes are frozen together.
•Ice cubes are hollow or smaller than normal.
•Ice maker should produce approximately 4 – 5 pounds of ice every 24 hours. Extra Ice should produce up to 8 pounds of ice every 24 hours.
•See PROBLEM section TEMPERATURES ARE TOO
WARM.
•Turn on household water line valve.
•If it is, replace the ice & water filter cartridge.
•Move item and release wire signal arm. Remove any ice cubes that are frozen together over the wire signal arm.
•Remove and shake ice container to separate cubes.
•The ice & water filter cartridge may be clogged. Replace filter cartridge.
•Cover foods tightly. Discard stale ice. Ice maker will produce fresh supply.
•Add filter to water supply line. Consult a water purifying company.
•Discard stale ice.
•When the first supply of ice is dropped into the container, the dispenser should operate.
•Turn freezer control to a higher setting so that ice cubes will be made. When first supply of ice is made, dispenser should operate.
•Open household water line valve. Allow sufficient time for the ice to be made. When ice is made, the dispenser should operate.
•Ensure freezer door is closed.
•Motor is overloaded. Motor overload protector will reset in approximately 3 minutes. Ice can then be dispensed.
•Remove ice container, thaw, and empty the contents. Clean container, wipe dry, and replace in proper position. When new ice is made, dispenser should operate.
•Remove ice cubes that are jamming the dispenser.
•Use the dispenser often so that cubes do not freeze together.
•The ice & water filter cartridge could be clogged. Replace the filter cartridge. Dispensing system operates best at 20 – 100 psi water pressure. Well water pressures should fall within this range.
23
Loading...