Installation and Operation Manual
Room Air Conditioners
Portable Chassis Models
XQ05, XQ06, XQ08, XQ10, EQ08
920-197-03 (6-10)
Table of contents |
|
Air Conditioner Operation |
|
Your Safety and the safety of others..................................................................................................................................................................................................... |
1 |
Before operating your unit....................................................................................................................................................................................................................... |
2 |
For the best cooling performance and highest energy ef ciency ......................................................................................................................................................... |
2 |
XQ models |
|
To start unit ............................................................................................................................................................................................................................................. |
3 |
To set mode of operation......................................................................................................................................................................................................................... |
3 |
MoneySaver® feature .............................................................................................................................................................................................................................. |
3 |
To adjust temperature ............................................................................................................................................................................................................................. |
3 |
To adjust fan speed ................................................................................................................................................................................................................................. |
3 |
To activate SMART FAN ......................................................................................................................................................................................................................... |
3 |
To set hour clock...................................................................................................................................................................................................................................... |
3 |
To set the timer ........................................................................................................................................................................................................................................ |
3 |
Automatic component protection ............................................................................................................................................................................................................ |
3 |
How to use the remote control................................................................................................................................................................................................................ |
4 |
EQ model |
|
Temperature control ................................................................................................................................................................................................................................ |
4 |
Function control....................................................................................................................................................................................................................................... |
4 |
Care and Maintenance |
|
Removing and cleaning the lter ............................................................................................................................................................................................................ |
5 |
Air Conditioner Installation |
|
Electrical requirements ........................................................................................................................................................................................................................... |
5 |
Installation hardware ............................................................................................................................................................................................................................... |
5 |
Sash window installations ....................................................................................................................................................................................................................... |
6 |
Through-the-wall installations ................................................................................................................................................................................................................. |
8 |
Troubleshooting tips .............................................................................................................................................................................................................................. |
10 |
Accessories ........................................................................................................................................................................................................................................... |
10 |
Warranty .................................................................................................................................................................................................................................................. |
11 |
Congratulations!
Thank you for your decision to purchase the Friedrich Room Air Conditioner. Your new Friedrich has been carefully engineered and manufactured to give you many years of dependable, efficient operation, maintaining a comfortable temperature and humidity level. Many extra features have been built into your unit to assure quiet operation, the greatest circulation of cool, dry air, and the most economic operation.
General Instructions
This Installation and Operation Manual has been designed to insure maximum satisfaction in the performance of your unit. For years of trouble-free service, please follow the installation instructions closely. We cannot overemphasize the importance of proper installation. We have added new information to the basic instructions to help you achieve success.
WARNING
Refrigeration system under high pressure.
Do not puncture, heat, expose to flame or incinerate.
Only certified refrigeration technicians should service this equipment.
R410A systems operate at higher pressures than R22 equipment. Appropriate safe service and handling practices must be used.
Only use gauge sets designed for use with R410A. Do not use standard R22 gauge sets.
WARNING
Please read this manual thoroughly prior to equipment installation or operation.
It is the installer’s responsibility to properly apply and install the equipment. Installation must be in conformance with the NFPA 70-2008 National Electric Code or current edition, International Mechanic Code 2009 or current edition and any other applicable local or national codes.
Failure to do so can result in property damage, personal injury or death.
Here are some suggestions to help you use your new Friedrich most efficiently:
1.Carefully read and follow the installation instructions.
2.Make sure the unit is the right capacity for the area being cooled. An undersized unit makes the unit work too hard, using more electricity than needed and increases wear. An oversized unit will cycle on and off too rapidly, and therefore cannot control humidity as well.
3.Clean the filter frequently (See Routine Maintenance).
4.Do not block the air flow to and from the unit. Make sure the louvers are directed to give even distribution.
5.A dirty filter or improperly set controls can affect the cooling ability of the unit.
6.If cooling is weak and you have verified that the filter is
clean and the controls are properly set, the unit may be low on refrigerant, and you should call your Friedrich service provider to check the unit.
7.Keep blinds, shades and drapes closed on the sunny side of the room being cooled to reduce radiant heat.
8.Proper insulation helps your unit maintain the desired inside temperature.
9.Whenever possible, shade south and west facing windows.
10.Keep window coverings away from the unit to provide free air flow.
Yoursafetyandthesafetyofothersareveryimportant.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is a safety Alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol with the word “WARNING” or “CAUTION”. These words mean:
Indicates a hazard which, if not WARNING avoided, can result in severe
personal injury or death and damage to product or other property.
CAUTION |
Indicates a hazard which, if not |
|
avoided, can result in personal injury |
and damage to product or other property. |
|
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what will happen if the instructions are not followed.
NOTICE |
Indicates |
property damage can |
|
occur if |
instructions are not |
|
followed.
1
WARNING: Before operating your unit
Make sure the wiring is adequate for your unit.
If you have fuses, they should be of the time delay type. Before you install or relocate this unit, be sure that the amperage rating of the circuit breaker or time delay fuse does not exceed the amp rating listed in Figure 1.
DO NOT use an extension cord.
The cord provided will carry the proper amount of electrical power to the unit; an extension cord will not.
Make sure that the receptacle is compatible with the air conditioner cord plug provided.
This insures proper grounding. If you have a two prong receptacle you will need to have it replaced with a grounded receptacle by a certi
ed electrician. The grounded receptacle should meet all national and local codes and ordinances. Under no circumstances should you remove the ground prong from the plug. You must use the three prong plug furnished with the air conditioner.
Test the power cord
All Friedrich room air conditioners are shipped from the factory with a Leakage Current Detection Interrupter (LCDI) equipped power cord. The LCDI device meets the UL and NEC requirements for cord connected air conditioners effective August 2004.
To test your power supply cord:
1.Plug power supply cord into a grounded 3 prong outlet.
2.Press RESET (See Figure 2).
3.Press TEST (listen for click; Reset button trips and pops out).
4.Press and release RESET (listen for click; Reset button latches and remains in). The power supply cord is ready for operation.
NOTE: LCDI device is not intended to be used as a switch.
Once plugged in, the unit will operate normally without the need to reset the LCDI device.
If the device fails to trip when tested or if the power supply cord is damaged, it must be replaced with a new supply cord from the manufacturer. We recommend you contact our Technical Assistance Line at (800) 541-6645 . To expedite service, please have your model and serial number available.
|
|
CIRCUIT RATING |
REQUIRED WALL |
||
|
|
OR TIME DELAY |
|||
MODEL |
RECEPTACLE |
||||
|
FUSE |
||||
|
|
||||
|
|
|
|
||
|
|
AMP |
VOLT |
NEMA NO. |
|
XQ0 |
XQ06 |
|
|
|
|
XQ0 |
XQ10 |
15 |
125 |
5-15R |
|
EQ08 |
|
||||
|
|
|
|
||
Figure 1
WARNING
Electrical Shock Hazard
Make sure your electrical receptacle has the same configuration as your air conditioner’s plug. If different, consult a Licensed Electrician.
Do not use plug adapters.
Do not use an extension cord.
Do not remove ground prong.
Always plug into a grounded 3 prong outlet. Failure to follow these instructions can result in death, fire, or electrical shock.
NOTE: Your LCDI device will resemble one of these illustrations.
RESET
TEST
RESET
WARNING
TEST BEFORE EACH USE
1. PRESS RESET BUTTON
2. PLUG LDCI INTO POWER TEST RECEPTACLE
3.PRESS TEST BUTTON,
RESET BUTTON SHOULD
POP UP
4.PRESS TEST BUTTON,
FOR USE
DO NOT USE IF ABOVE TEST
FAILS
WHEN GREEN LIGHT IS ON
IT IS WORKING PROPERLY
Figure 2
.
2
How to operate your Friedrich room air conditioner (XQ models)
To start unit
If your air conditioner is installed and plugged into a proper receptacle, it is ready to go. The first time the unit is started, the compressor will delay for three minutes. See Automatic Component Protection on the following page.
1Touch the Power button once. The unit will automatically be in Cool mode with the temperature set at 75°F (24°C) and the fan speed at F1, the sleep setting.
To set mode of operation
When you 
rst turn the unit on, it will be in the Cool mode (light on), with constant fan.
2Touch the Mode button once to activate the MoneySaver® (light on).
MONEYSAVER® is a feature that cycles the fan with the compressor so that the fan does not run all the time. This saves energy and improves dehumidi
cation. Or you may prefer constant fan for more air move ment (to return to constant fan, touch the Mode button two more times).
8 |
9 |
2 |
3 |
4 |
1 |
FIGURE 3 |
|
|
|
|
|
|
X STAR
PM
|
|
Cool |
|
|
Fan |
Mode |
Money Saver® |
|
|
Speed |
|
|
|
|
|
|
Fan Only |
|
|
|
|
Clock |
|
|
Timer |
Set |
Start Time |
|
|
On/Off |
Hour |
Stop Time |
|
|
|
|
Temp/Hour |
||
|
|
|
||
|
|
|
5 |
6 |
13 10 11 12
7
In order to run the fan by itself, do the following:
3Continuing from MoneySaver® mode (light on), touch the Modebutton once to activate the FAN ONLY feature (light on).
The FAN ONLY setting will circulate air in the room without the compressor coming on.
To adjust temperature
4Use the Mode button to select either the COOL or MoneySaver® function
5COOLER – Touch the 
button to lower the room air temperature.
6WARMER – Touch the 
button to raise the room air temperature.
7Press both the 
and 
buttons at the same time to switch the temperature readout from Fahrenheit (°F) to Celsius (°C).
Repeat step 7 to switch from °C back to °F.
To adjust fan speed
8Touch the FanSpeedbutton to see the current setting. Touch it again to change speed. F1 is the lowest setting (SLEEP SETTING / LOW), F2 is MEDIUM, and F3 is HIGH.
To activate Smart Fan
9There is a fourth option, SF, when selecting the fan speed. This is the SMART FAN function. SMART FAN DOES NOT OPERATE IN CONJUCTION WITH THE FAN ONLY MODE.
Smart Fan will adjust the fan speed automatically to maintain the desired comfort level. For example, if the outside doors in your home are opened for an extended period of time, or more people enter a room, Smart Fan may adjust to a higher fan speed to compensate for the increased heat load. This keeps you from having to adjust the fan speed on your own.
To set the hour clock
10Touch the Set Hour button to see the current setting (clock light comes on). The number that is displayed is the approximate time (hour only). Use the 
and 
buttons to change the settings. BE SURE TO SET A.M. AND P.M. ACCORDINGLY. (P.M. is indicated by a red light in the upper left corner of the display).
To set the timer
NOTE: Set the HOUR CLOCK before attempting to set timer functions.
You can set the START and STOP times a minimum of one hour apart, and a maximum of twenty-three hours apart.
11After setting the time, press the Set Hour button once (Start light comes on). Use the 
and 
buttons to select the time that the unit will START.
12After selecting the START time, press the SetHourbutton once more (Stop light comes on). Use the 
and 
buttons to select the time that the unit will STOP. After selecting the stopping time, press the Set Hour button once.
13Press the Timer On/Off button (light turns on) to activate the timer function. To deactivate this function, press the Timer On/Off button once again (light turns off). Once the on and off times have been selected, they will remain in memory and cycle daily until changed.
NOTE: If the unit is unplugged or the power is interrupted, the HOUR must be reset or the Timer On/Off will not function when desired.
Automatic component protection
Your unit is equipped with Automatic Component Protection. To protect the compressor of the unit, there is a three minute start delay if you turn the unit off or if power is interrupted. The fan operation will not be affected. Also, if you switch from Cool mode to Fan Only, and switch back to Cool mode, there is a three minute delay before the compressor comes back on.
3
How to use the remote control
To start unit
1POWER - Press the Power button once. The unit will automatically start in the mode and fan speed it was last left on.
To set mode of operation
2COOL - Press the Cool button to automatically switch the operating mode to COOL.
3FAN ONLY - Press the Fan Only button if you want to run the fan only.
4MoneySaver® - Press the MoneySaver® button to activate the MoneySaver® feature. This feature cycles the fan with the compressor so that the fan does not run all the time.
To adjust temperature setting
5WARMER - Press the 
Warmer button to raise the temperature setting.
6COOLER - Press the 
Cooler button to lower the temperature setting.
To adjust fan speed
7FAN SPEED - Press the Fan Speed button to see the current setting. Press again to change the fan speed. F1 is the lowest setting (SLEEP / LOW), F2 is MEDIUM, F3 is HIGH, and SF is the SMART FAN setting.
To set the hour clock
8SET HOUR CLOCK - Press Set Hr. once to see the current clock setting. Continue pressing the button until you arrive at the current time (Hour only). Minutes are not shown on the display. Make sure that the A.M. / P.M. setting is correct.
To set the timer
NOTE: You can set the START and STOP times a minimum of one hour apart, and a maximum of 23 hours apart.
9TIMER START - Press Start to view the current start time for cooling. Continue pressing the Start button until you arrive at the start time you desire. The start time for cooling will then be set.
10TIMER STOP - Press the Stop button. Continue pressing the Stop button until you arrive at the stop time you desire. The stop time for cooling will then be set.
11TIMER ON / OFF - Press the On/Off button to activate (light on) or deactivate (light off) the timer. Once the on and off times have been selected, they will remain in memory and cycle daily until changed.
NOTE: If the unit is unplugged or the power is interrupted, the Set Hr. function must be reset or the On/Off function will not work.
FIGURE 4
Temperature |
|
|
|
|
Cooler |
|
Warmer |
||
6 |
|
|
|
5 |
Cool |
|
|
|
Power |
2 |
|
|
|
1 |
Fan |
Fan |
|
|
Money |
3 |
|
|
|
4 |
Only |
Speed |
|
Saver® |
|
Timer Operation |
|
|
7 |
|
On/Off |
Start |
Stop |
Set Hr. |
|
11 |
|
|
|
8 |
9 |
|
|
|
10 |
Additional RC1 wireless remote controls can be purchased from your Friedrich dealer.
How to operate your Friedrich room air conditioner (EQ08 model)
Function control
The left knob is a six position control that allows you to select heat or cool in either low speed or high speed. Plus you can select fan only if you wish.
Temperature control
o c , r e l o o c |
i w k c o l c |
r a w r o f e s i |
c |
FIGURE 5
4
Care and maintenance
To remove filter
Simply turn the unit off and pull the filter frame up and towards you (See Figure 6). Clean with warm water and a mild detergent, rinse, dry, and replace by sliding the filter back into position behind the front panel.
Figure 6
Installation instructions
NOTE: This section includes installation instructions for window mount and thru-the-wall mount methods. X-Star® heat/cool units are designed for permanent thru-the-wall installation. Mounting the unit in a window will require a window mounting accessory kit, available through your Fried rich dealer.
WARNING
Electrical Shock Hazard
Make sure your electrical receptacle has the same configuration as your air conditioner’s plug. If different, consult a Licensed Electrician.
Do not use plug adapters.
Do not use an extension cord.
Do not remove ground prong.
Always plug into a grounded 3 prong outlet. Failure to follow these instructions can result in death, fire, or electrical shock.
READ THIS FIRST! Electrical Requirements
IMPORTANT: Before you begin the actual installation of the air conditioner, be sure your electrical requirements are as described below. Consult an electrical professional as necessary to insure home wiring is per local electrical codes.
CIRCUIT PROTECTION - An overloaded circuit will invariably cause malfunction or failure of an air conditioner, therefore, it is necessary that the electrical protection is adequate. All portable chassis models require a 15 amp fuse or circuit breaker for over-amperage protection. Due to momentary high current demand when your air conditioner is started, use a "TIME DELAY" fuse or a HACR type circuit breaker. Consult your dealer or power company if in doubt.
Your air conditioner must be connected to a power supply with the same A.C. voltage and hertz as marked on the unit nameplate. Only alternating current (A.C.), no direct current (D.C.), can be used.
The power cord has a plug with a grounding prong of approved type and a matching plug receptacle with ground is required. Refer to page 3 for the correct type of plug receptacle for your model.
WARNING: NEVER CUT OR REMOVE THE GROUNDING PRONG FROM PLUG. NEVER USE EXTENSION CORDS TO OPERATE AN AIR CONDITIONER.
Items required for installation (provided in straight cooling units only)
ITEM NO. |
DESCRIPTION |
QTY. |
|
|
|
1 |
SCREW, SHEET METAL, #8 X " |
8 |
2 |
SCREW, PHILLIPS, TRUSS HEAD, #8 X ½" |
4 |
3 |
SCREW, HEX, #8 X " |
10 |
4 |
SCREW, PHILLIPS, #8 X 1 ¼" |
2 |
|
|
|
5 |
GRAY GASKET, FOAM, 1" X 1 ½" X 42" |
1 |
6 |
WHITE GASKET, FOAM, 1" X 1 ½" X 48" |
1 |
|
|
|
ITEM NO. |
DESCRIPTION |
QTY. |
|
|
|
7 |
LEFT SIDE CURTAIN ASSEMBLY |
1 |
8 |
RIGHT SIDE CURTAIN ASSEMBLY |
1 |
|
|
|
9 |
DECORATIVE FRONT PANEL |
1 |
10 |
CABINET OR SLEEVE |
1 |
11 |
AIR CONDITIONING UNIT |
1 |
|
|
|
ITEM 1 |
|
ITEM 2 |
|
ITEM 3 |
|
ITEM 4 |
|
ITEM 5 |
|
ITEM 6 |
|
|
|
|
|
|
|
|
|
|
|
ITEM 7 |
|
ITEM 8 |
|
ITEM 9 |
|
ITEM 10 |
|
ITEM 11 |
|
|
|
|
|
|
|
|
|
SASH WINDOW INSTALLATIONS
WARNING
Falling Object Hazard
Not following Installation Instructions for mounting your air conditioner can result in property damage, injury, or death.
STEP 1 After removing the unit from shipping carton, remove tape holding decorative front in place. Lay front in a safe out-of-the-way place, then slide chassis out of cabinet (see Figure A).
STEP 2 Attach curtain assemblies to cabinet as shown in Figure B. Use eight
(8) No. 8 x " slotted hex head screws (item #1, page 6).
STEP 3 Center cabinet in window with sill channel positioned against window stool as shown in Figure C, Section A-A.
STEP 4 Pull window sash down behind Shell Support Channel on top of cabinet; this helps hold cabinet in place. Install No. 8 x " hex head screw (item #3, page 6) in sill channel at bottom of window opening as shown in Figure C.
STEP 5 Extend the sliding curtains on each side so the frames t into the window channels. While holding the curtain frames in place, mark four (4) hole locations (hole locations are in the upper corners on left and right curtain assembly), two (2) in the window jamb and two (2) in the window sash. Slip the curtains back from marked locations and drill four (4) 7/ 64" diameter pilot holes. Again, extend the sliding curtains on each side and then install two (2) no. 8 x ½" Phillips head screws (item #2, page 6) and two (2) No. 8 x 1 ¼" Phillips head screws (item #4) through the curtain frames as shown in Figure C.
FIGURE B
CURTAIN
ASSEMBLY
RETAINING
BRACKET SHELL SUPPORT CHANNEL
CURTAIN ASSEMBLY (LEFT)
SCREW #8 x " SLOTTED HEX HEAD |
|
|
(ILLUSTRATION ON PAGE 6, ITEM #1) |
CURTAIN |
|
8 REQUIRED (4 EACH SIDE). INSTALL |
||
ASSEMBLY |
||
FROM INSIDE SLEEVE TO CURTAIN |
||
(RIGHT) |
||
ASSEMBLY RETAINING BRACKET |
||
|
CAUTION
Excessive Weight Hazard
Use two or more people when installing your air conditioner.
Failure to do so can result in back or other injury.
CAUTION
Cut/Sever
Although great care has been taken to minimize sharp edges in the construction of your unit, use gloves or other hand protection when handling unit.
Failure to do so can result in minor to moderate personal injury.
FIGURE A
TO PULL UNIT FROM SLEEVE, USE PULL STRAP AND BASEPAN |
WHEN CARRYING OR HANDLING UNIT, OBTAIN ASSISTANCE OR |
HANDLE LOCATED ON FRONT. OBTAIN ASSISTANCE OR HELP |
HELP AS NECESSARY TO SUPPORT UNIT FROM BOTTOM (BASE |
AS NECESSARY TO HOLD SLEEVE WHILE PULLING UNIT FROM |
PAN), MAINTAINING CLEARANCE FROM ALL OBSTACLES. |
SLEEVE. MAKE SURE AIR CONDITIONER IS ON FIRM SUPPORT |
|
BEFORE REMOVING UNIT FROM SLEEVE. |
|
PULL STRAP
BASEPAN HANDLE
FIGURE C
SCREW, 1/2” PHILLIPS HEAD (See illustration, item #2, page 6)
SCREW, 1 1/4” PHILLIPS HEAD (See illustration, item #4, page 6)
SCREW, #8 x 7/8” HEX HEAD (See illustration, item #3, page 6)
SILL
CHANNEL
WINDOW STOOL
SECTION A-A
6
SHELL SUPPORT CHANNEL
WINDOW SASH
CABINET
STEP 6 Inspect the unit before inserting it into the sleeve. The fan and blower wheel should be manually rotated to insure that they turn freely. Be sure the electrical cord will be out of the way when inserting the unit into the sleeve.
NOTE: For your safety, DO NOT plug the electrical cord into an electrical outlet until installation is complete.
STEP 7 If the unit checks out OK, it is ready to be placed into position on bottom rails of the cabinet and pushed into place.
NOTE: Do all lifting of the unit by the bottom pan only and with assistance or help as necessary (see Figure A).
STEP 8 Install the white chassis seal gasket (item #6, page 6) and the gray window seal gasket (item #5). Carefully insert the white gasket (item #6) between the chassis and the cabinet starting at either bottom corner and go up the side, across the top and down the opposite side. Insert the gray gasket (item #5) between the window sashes as shown in Figure D. If chassis seal gasket is not installed, the operation of the unit will be negatively affected. Also, the operation noise and outside noise will be amplified.
STEP 9 Hold the decorative front as shown in Figure E. Insert the two tabs of the Decorative Front Panel into the slots in the top of the cabinet and lower the bottom of the decorative front to the bottom of the cabinet. Route the electrical cord to the right or left side of the bottom of the cabinet as required by the location of the electrical wall outlet. Use the notches provided at the bottom of the Decorative Front Panel for routing the electrical cord out of the unit. Attach the decorative front to the cabinet with two (2) No. 8 x ½" Phillips head screws (item #2, page 6).
WARNING
Electrical Shock Hazard
Unplug unit when servicing.
Failure to follow these instructions can result in death, fire, or electrical shock.
STEP 10 CIRCUIT PROTECTION - If the air conditioner is circuit protected by a fuse, use a "TIME DELAY" fuse or HACR type Circuit Breaker due to momentary high current demand when your air conditioner is started. Before operating your unit, verify the ampere rating of the time-delay fuse or circuit breaker which protects your unit. The ampere rating of the time-delay fuse or circuit breaker shall be 15 amps. Refer to Operation section for more detailed operating instructions.
FIGURE D
GRAY FOAM GASKET
(see illustration, item #5 on page 6)
CHASSIS SEAL GASKET
TO PREVENT AIR LEAKS AROUND
THE AIR CONDITIONER, INSERT
THE WHITE FOAM GASKET (item
# 6, page 6) BETWEEN THE AIR CONDITIONER AND THE CABINET.
FIGURE E
TAB SLOTS
TAB
LOCATIONS
NOTCHES PROVIDED
FOR ELECTRICAL
CORD EXIT
SCREW, #8 x ½" PHILLIPS HEAD (See ilustration, item # 2, page 6) 2 REQUIRED (1 EACH SIDE)
CAUTION
Excessive Weight Hazard
Use two or more people when installing your air conditioner.
Failure to do so can result in back or other injury.
WARNING
Moving Object Hazard
Replace all panels before operating your air conditioner.
Failure to do so can result in injury.
7
THRU-THE-WALL INSTALLATIONS
WARNING
Falling Object Hazard
Not following Installation Instructions for mounting your air conditioner can result in property damage, injury, or death.
STEP 1 After removing the unit from shipping carton, remove tape holding |
STEP 5 Position the front edge to extend into the room 3/4" minimum at |
decorative front in place. Lay front in a safe out-of-the-way place, |
top of cabinet and 1" minimum at bottom (see Figure G). |
then slide chassis out of cabinet (see Figure A, page 7). |
|
STEP 2 Remove the shell channel from the top of the cabinet (see Figure B, page 7).
NOTE: Not applicable to heat pump models sold without quick mounting cabinet.
STEP 3 LAYOUT - Cut and frame in an opening in the desired wall area using the illustration as a guide (see Figure F).
STEP 4 Place the cabinet in the framed opening.
NOTE: Measure and shim void spaces between the side of cabinet and wood framing before securing to wall.
STEP 6 Secure each side of the cabinet with No. 8 x " hex head screws (item #3, page 6) or nails through the holes in the sides.
NOTE: ALTERNATE FASTENERS WHICH MAY BE USED FOR SECURING THE UNIT CABINET TO A WALL, INCLUDING MASONRY WALLS, ARE NOT FURNISHED (AVAILABLE AT LOCAL HARDWARE STORES).
MOLLY OR TOGGLE BOLT |
EXPANSION ANCHOR BOLT |
FIGURE F
2" X 8" FRAME
FINISHED OPENING SIZE
20"
20"
14 ¼"
14 ¼"
CONCRETE BLOCK CONSTRUCTION |
FRAME CONSTRUCTION |
FIGURE G
¾" MINIMUM
CABINET FRONT
1" THICK LUMBER
1" MINIMUM INSIDE WALL
EXTERIOR WALL
FRONT EDGE OF LOUVERS MUST ALWAYS BE OUTSIDE OF EXTERIOR WALL SURFACE
¼" SLOPE
DOWN. POSITION AND SECURE CABINET DOWNWARD. SLOPE OUTSIDE FOR DRAINAGE.
MAX. WALL
THICKNESS
ALLOWED 8 ½"
¾" MINIMUM FRONT EDGE OF CABINET TO INSIDE WALL SURFACE.
TRIM AROUND THE CABINET
WITH A SUITABLE WOOD
MOULDING AND FINISH TO SUIT.
CAULK ALL AROUND CABINET
ON OUTSIDE TO INSURE A
WEATHER TIGHT SEAL.
" SLOTTED HEAD SCREWS (3 EA. SIDE)
NAILS MAY BE USED IF DESIRED.
8
STEP 7 |
Cut two pieces of standard 1" lumber (supplied by installer) to the |
STEP 9 Complete the installation by following STEPS 6 through 10 of Sash |
|
length and width required. Place in front and back of bottom sill chan- |
Window Instructions (Page 8). Window Seal Gasket mentioned |
|
nel as shown in Figure G. Secure with nails (supplied by installer). |
in STEP 8 will not be required. |
STEP 8 |
Seal all holes in the cabinet with caulking compound (supplied |
IMPORTANT: Before operating your unit, read STEP 10 of Sash |
|
by installer). |
Window Instructions. |
FIGURE H
SOLID MASONRY CONSTRUCTION
CAULK ALL SIDES
CABINET
MORTAR
NOTE: ELECTRICAL RECEPTACLE LOCATION
FROM POINT "X" MUST BE WITHIN A MAXIMUM
RADIUS OF 69" FOR 115V UNITS.
ELECTRICAL RECEPTACLE
POINT "X"
9
Troubleshooting tips
Power failure
If you have a power failure, the unit's auto-restart feature will resume operation in the selected mode prior to the power failure.
Won't cool?
If your air conditioner operates, but won’t cool; check to see if the controls are properly set. Check the filter and clean thoroughly if needed. Check to see if the chassis seal gasket is installed (refer to Installation Instructions, Step 8, page 8).
Won't run?
Make sure the power cord is plugged in completely. Check for a bad fuse, tripped breaker or tripped LCDI Device. Refer to page 3 for LCDI reset instructions and to con rm proper fuse size.
For XQ models only:
You can reset the circuit board by pressing the “MODE” button and the “TEMPERATURE DOWN” button at the same time. The LEDs (small red lights) for Hour, Start and Stop will begin blinking. Once this occurs, turn the unit off by pressing the On/Off button once and then unplug the unit. Finally, plug the unit back in and turn it on by pressing the On/Off button once. All settings revert back to the factory default settings.
This is a warm weather appliance
Your air conditioner is designed to cool in warm weather when the outside temperature is above 60°F (16°C), so it won't cool a room if it is already cool outside. Also, it will not provide adequate heating when the outdoor ambient temperature falls below 37°F (3°C).
Condensation is normal
Air conditioners actually pump the heat and humidity from your room to the outside air. Humidity becomes water, and your air conditioner will use most of the water to keep the outside coil cool. If there is excessive humidity, there may be excess water that will drip outside. This is normal operation.
Frosting
This usually occurs because of insufficient airflow across the coils, a dirty filter, cool damp weath er, or all of these. Set unit to Fan Only and the frost will disappear. Setting the thermostat a little warmer will probably prevent the frosting from recurring.
Noises
All air conditioners make some noise. We build them to operate as quietly as possible. An air conditioner mounted in a wall is quieter than one mounted in a window. It is important to ensure that the chassis seal gasket is properly installed (refer to Installation Instructions, Step 8, page 8).
Cleaning your air conditioner
The decorative front and the cabinet can be cleaned with warm water and a mild liquid detergent. The indoor coil can be vacuumed with a dusting attachment if it appears to be dirty. The outdoor coil can be gently sprayed with a hose if you can get to it. If not, you might call your dealer for a more thorough cleaning when needed. The air lter should be inspected weekly and cleaned if needed by vacuuming with a dust attachment or by cleaning in the sink using warm water and a mild dishwashing detergent. Dry the lter thoroughly before reinstalling. Use caution– the coil surface can be sharp.
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.
Available accessories
Window installation kits - heat pump models
Friedrich EQ Electric Heat models are normally installed thru-the-wall and are packaged and sold without the expandable curtain assemblies. The WIKQ Curtain Assembly Kit may be purchased as an accessory for window installations. This accessory can be ordered from your Friedrich Dealer. When ordering a kit, state model and serial number of your unit.
10
Friedrich Air Conditioning Company
10001 Reunion Place, Suite 500
San Antonio, Tx 78216
1-800-541-6645
www.friedrich.com
ROOM AIR CONDITIONERS
LIMITED WARRANTY
FIRST YEAR
ANY PART: If any part supplied by FRIEDRICH fails because of a defect in workmanship or material within twelve months from date of original purchase, FRIEDRICH will repair the product at no charge, provided room air conditioner is reasonably accessible for service. Any additional labor cost for removing inaccessible units and/or charges for mileage related to travel by a Service Agency that exceeds 25 miles one way will be the responsibility of the owner. This remedy is expressly agreed to be the exclusive remedy within twelve months from the date of the original purchase.
SECOND THROUGH FIFTH YEAR
SEALED REFRIGERANT SYSTEM: If the Sealed Refrigeration System (defined for this purpose as the compressor, condenser coil, evaporator coil, reversing valve, check valve, capillary, filter drier, and all interconnecting tubing) supplied by FRIEDRICH in your Room Air Conditioner fails because of a defect in workmanship or material within sixty months from date of purchase, FRIEDRICH will pay a labor allowance and parts necessary to repair the Sealed Refrigeration System; PROVIDED FRIEDRICH will not pay the cost of diagnosis of the problem, removal, freight charges, and transportation of the air conditioner to and from the Service Agency, and the reinstallation charges associated with repair of the Sealed Refrigeration System. All such cost will be the sole responsibility of the owner. This remedy is expressly agreed to be the exclusive remedy within sixty months from the date of the original purchase.
APPLICABILITY AND LIMITATIONS: This warranty is applicable only to units retained within the Fifty States of the U.S.A., District of Columbia, and Canada. This warranty is not applicable to:
1.Air filters or fuses.
2.Products on which the model and serial numbers have been removed.
3.Products which have defects or damage which results from improper installation, wiring, electrical current characteristics, or maintenance; or caused by accident, misuse or abuse, fire, flood, alterations and/or misapplication of the product and/or units installed in a corrosive atmosphere, default or delay in performance caused by war, government restrictions or restraints, strikes, material shortages beyond the control of FRIEDRICH, or acts of God.
OBTAINING WARRANTY PERFORMANCE: Service will be provided by the FRIEDRICH Authorized Dealer or Service Organization in your area. They are listed in the Yellow Pages. If assistance is required in obtaining warranty performance, write to: Room Air Conditioner Service Manager, Friedrich Air Conditioning Co., P.O. Box 1540, San Antonio, TX 78216-1540.
LIMITATIONS: THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES. Anything in the warranty notwithstanding, ANY IMPLIED WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE AND/OR MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS EXPRESS WARRANTY. MANUFACTURER EXPRESSLY DISCLAIMS AND EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY.
Performance of Friedrich’s Warranty obligation is limited to one of the following methods:
1.Repair of the unit
2.A refund to the customer for the prorated value of the unit based upon the remaining warranty period of the unit.
3.Providing a replacement unit of equal value
The method of fulfillment of the warranty obligation is at the sole discretion of Friedrich Air Conditioning.
NOTE: Some states do not allow limitations on how long an implied warranty lasts, or do not allow the limitation or exclusion of consequential or incidental damages, so the foregoing exclusions and limitations may not apply to you.
OTHER: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
PROOF OF PURCHASE: Owner must provide proof of purchase in order to receive any warranty related services.
All service calls for explaining the operation of this product will be the sole responsibility of the consumer.
All warranty service must be provided by an Authorized FRIEDRICH Service Agency, unless authorized by FRIEDRICH prior to repairs being made.
(11-09)
11
Manual de instalación y funcionamiento
Unidades de aireacondicionado detipoventana
|
Temperature |
|
|
|
|
Cooler |
|
|
|
|
Warmer |
|
Cool |
|
|
|
Fan |
|
Power |
Only |
Fan |
|
|
Speed |
Money |
||
Timer |
|
|
|
On/Off |
Operation |
Saver |
|
|
Start |
Stop |
|
|
|
|
SetHr. |
Modelos de chasis portátil
XQ05, XQ06, XQ08, XQ10, EQ08
920-197-03 (6-10)
Loading...