Footprint Security H.264 User Manual

H.264 NETWORK Embedded DVR

User

User Manual

Manual

V1.0- 3531_4CH_SDI

Thank

Thank you

you

you for

for

for purchase

purchase

purchase our

our

our product

product

product .

.

. Please

Please

Please read

read

read this

this

this user

user

user manual

manual

manual carefully

carefully

carefully to

to

to ensure

ensure

that

that you

you

you can

can

can use

use

use the

the

the device

device

device correctly

correctly

correctly and

and

and safely

safely

safely .

.

Attentions

Attentions :

:

◆ T he DVR should be installed in a well-ventilated place ， keep suitable space from ground ,benefit for machine cooling ， Be sure not to block its air vent. ， keep away from heat sources and high temperaturea environment 。

◆ Please keep the level installation of this product.should be avoid install at violently shaking place （ such as the back of car 、 motor above 、 high and rough luggage-rake ） .

◆ F or avoid short circuit cause fire or other damage ， when wash the car please prevent DVR(include camera and other parts) touch water and wet, the machine don’t have waterproof.

◆ The equipment consists of Precision Parts, please d o not try to disassemble or adjust any parts, if need maintenance, please contact the distributer or customer service .

◆ Please select the hard disk which commended by the manufacturers ,suit the DVR work requirement , to meet a long time largeamount of data read and write requests , please purchase from the formal channels to ensure the hard disk quality .

◆ This product can

’ t

bear heavy weight, please do not place heavy object

or multi-layer laminated on the product

.

Disclaimer:

T he Company is do the best to make the contect correct and complete during the preparation of this manual , if has any errors or omissions without any liability , the company reserves the right to change any hardware and software mentioned inthis manual at any time , and without explain beforehand. Thank you for choosing our products, please read this manual carefully before use . Due to not according to the specified operating losses, company will not assume any financial liability and legal responsibility .

3

CONTENT

1. Product Introduction ................................................................................................... 4

1.1 Summary ................................................................................................................ 4

1.2 Main functions ………………………………………………………………… 4

1.3 Front panel buttons description ......................................................................... 5

1.4 Rear panel diagram ………………………………………………………… . . 6

1.5 R emote control ………………………………………………………………… 7

2. Basic function operation

............................................................................................

8

2.1 On/off Switching navigation ................................................................................ 8

2.2 Login …………………………………………………………………………… 8

2.3 Main menu setup guide

.......................................................................................

9

2.4 Configuration management ……………………………………………… ... 10

2.4.1 Basic configuration ....................................................................................

11

2.4.2 Live configuration ...................................................................................... 12

2.4.3 Record configuration

................................................................................

13

2.4.4 Schedule configuration ............................................................................ 15

2.4.5Alarm configuration ………………………………………………… ..... 16

2.4.6 Network configuration .............................................................................. 20

2.4.7 User management …………………………………………………… ...22

2.4.8

P.T.Z

configuration .................................................................................... 24

2.4.9 A dvance configuration .............................................................................. 27

2.5 Data retrieval ...................................................................................................... 27

2.5.1 Time search

................................................................................................

27

2.5.2 Event search .............................................................................................. 28

2.6 Backup ................................................................................................................. 29

2.7 C heck information ............................................................................................. 29

2.8 Disk management

.............................................................................................

29

2.9 Upgrade ............................................................................................................... 30

2.10 Logoff ................................................................................................................. 30

2.11 System shut down ........................................................................................... 30

4

1.

1. Product

Product

Product Introduction

Introduction

1.1

1.1 Summary

Summary

This device is a digital monitoring and recording product specially designed for the

security field. It adopts standalone processor and standalone Linux operati ng system.

The device combines with the latest technologies in the IT field, such as video and audio compression/decompression, large capacity HDD record, TCP/IP network etc. . The code is embedded in the FLASH chip , which makes the system running more steadily. This device has both features of digital video and audio recording(DVR) and digital video and audio server(DVS). It can not only work locally and independently but also compose of a powerful security monitoring net with networking. With the use of professional network video surveillance platform (network) software, it can fully reflect its strong networking and remote monitoring capability.

It can be used for the security protection in the fields of banking, telecommunications, electronic power, justice, traffic, residential, factory, warehouse, water conservancy facilities and other areas and departments.

1.2

1.2 Main

Main

Main Functions

Functions

�

� Real

Real

Real -

-

- time

time

time Monitoring

Monitoring

It is with analogue video output port, VGA port and HDMI port . It can realize the monitoring function through the monitor or display. It supports simultaneous TV ， VGA and HDMI output .

�

� S

S

S torage

torage

torage Function

Function

It adopts special format to save data which cannot be tampered with and will be secured

�

� Compression

Compression

Compression Method

Method

It supports multi-channel audio and video signal. Each channel of audio and video signal is compressed in real time by independent hardware. The sound and image keep stabilized synchronization.

�

� Backup

Backup

Backup Function

Function

It backups through USB port(such as common U disk, mobile hard disk,

SATA

Combo etc.)

The client computer can download and backup the files on the hard disk via the internet

�

� Video

Video

Video Play

Play

Play back

back

back Function

Function

Each channel can realize independent and real - time recording, while retrieval , reverse play , network monitoring, video search and download etc. can realize simultaneously .Multiple playback modes: slow forward , fast forward , reverse play and frame-by-frame play. When playing back the video , the exact time of the event can be displayed.

�

� Network

Network

Network Operation

Operation

Operation Function

Function

T hrough the internet , y ou can realize remote and real - time monitoring, remote video search and playback , and remote PTZ control .

�

� Communication

Communication

Communication Port

Port

With RS4 22 port and PTZ control. With standard Ethernet port, realizing network remote control function

�

� PTZ

PTZ

PTZ Control

Control

Support the PTZ decorder which communicates through RS4 22. Can expand multiple decoding protocol s, facilitating the realization of PTZ and dome camera control.

�

� Intelligent

Intelligent

Intelligent Operation

Operation

Mouse operation function.For the same settings on the menu, you can copy and paste quickly.check equipment and accessories .. When you receive the product, please check the accessories are complete or not.

5

DVR accessories generally include: mouse, power lines and data lines .

1.3

1.3 F

F

F ront

ront

ront panel

panel

panel buttons

buttons

buttons description

description

Statement

Statement : the front panel interface, button layout and type, real product shall prevail.

The front panel buttons Description

:

Buttons

Buttons on

on

on Front

Front

Front Panel

Panel

1 ） STANDBY

STANDBY

STANDBY : Press to power the system standby.

2 ） IR

IR

IR Sensor

Sensor

Sensor : IR receiver for the remote control.

3 ） LED

LED

LED Indicators

Indicators

Indicators : Shows status of alarm, rec , power .

4 ） Channel/Numbers/Playback

Channel/Numbers/Playback

Channel/Numbers/Playback : Press buttons 0~9 to view the selected channel in

full-screen; press buttons 0~9 to input passwords and user IDs; during playback, press the following:

• 6/

:

Increase reverse playback speed 1X, 2X, 4X

• 7/ : Press to freeze playback to one frame, then press again to advance

frame-by-frame

• 8/ : Press to start playback

• 9/ : Press to slow playback speed by 1/2, 1/4, 1/8

• 0/

:

Press to increase forward playback speed 1X, 2X, 4X

5 ） MENU/

MENU/

MENU/ OK

OK

OK : Press to open/close the main menu.or confirm.

6 ） Navigation:

Navigation:

Navigation: Press the Navigation buttons to perform the following:

• : In menus, press to confirm selections; in PTZ mode, press to change the navigation

buttons to control the connected PTZ camera (not included)

• : Press to move cursor up; in PTZ mode, press to pan camera up

•

:

Press to move cursor down; in PTZ mode, press to pan camera down

•

:

Press to move cursor left; in PTZ mode, press to pan camera left

• : Press to move cursor right; in PTZ mode, press to pan camera right 7 ） USB

USB

USB : Connect a USB flash drive to the top port for data backup and firmware

upgrades connect a USB mouse to the bottom port.

6

1.4

1.4 Rear

Rear

Rear panel

panel

panel diagram

diagram

Statement:

Statement: the rear panel interface, button layout and type, real product shall

prevail. ， below rear panel picture may be different with the actual panel.

Connectors

Connectors on

on

on Rear

Rear

Rear Panel

Panel

Panel ：

Item Physical connector Connector description

1 P ower input DC 1 2V / 5 A

2 Power swich POWER ON/OFF

3 Video output

video output for connecting TV or

monitor (BNC)

4 Video input

For connecting digtial video signal

input (BNC)

5 Audio Input For connecting audio signal input

6

Alarm Input 4 I/O alarm input

Alarm Output I/O output for alarm

RS 422 RS 422 for connecting PTZ

7 Network For connecting Ethernet

8 VGA For connecting VGA monitor

9 Audio Output For connection audio output

10 HDMI For connecting HDMI monitor

11

LINE IN For connecting Intercom equipment

7

TIP

:

When using the remote control to enter password and camera titles, select the field using the navigation buttons, press ENTER, and then press the number buttons.

1.5

1.5 R

R

R emote

emote

emote control

control

The remote control is the secondary input device For navigating the system’s interface. To

use the remote control:

1. STANDBY

STANDBY

STANDBY :Press to turn standby mode ON/OFF.

2. LOGIN/LOCK

LOGIN/LOCK

LOGIN/LOCK : If "Security" has been enabled in

the Setup menu, press to open the user password login screen.

3. Number/Channel

Number/Channel

Number/Channel buttons

buttons

buttons : While in menus,

press buttons 0~9 to enter values; during live viewing, press to view channels in full-screen.

4. QUAD

QUAD

QUAD :

:

: Press to switch between quad and

split-screen displays.

5.PTZ

PTZ

PTZ : Press to open the PTZ control window.

6. Playback controls

:

•

:

Increase reverse playback speed 2X, 4X, 8X.

•

:

Press to start playback.

•

:

Press to increase forward playback speed

2X, 4X, 8X.

• : Press to slow playback speed by 1/2, 1/4,

1/8.

• : Press to to advance frame-by-frame.

• ║ : Press to freeze playback to one frame.

• ■ : Press to stop playback.

7. SERACH: Press to stop playback

8. RECORD:Press to start manual recording,

then press again to stop manual recording.

9. +/

+/

+/ -

-

- : In menus, press to adjust values.

10. MENU

MENU

:

Opens the main menu

.

11.

EXIT

EXIT : Close menu windows

12. EXTRA

EXTRA

EXTRA : For the future use .

13. Navigation/

Navigation/

Navigation/ Enter

Enter

Enter :

• : Move cursor in menus up;

• : Move cursor in menus right;

•

:

Move cursor in menus left;

•

:

Move cursor in menus down;

• Enter

Enter

Enter : In menus, press to confirm selections;

during playback and preview, press to view system information

Check

Check whether

whether

whether there

there

there is

is

is fluorescent

fluorescent

fluorescent light

light

light being

being

being used

used

used in

in

in the

the

the nearby

nearby

For the convenience of readers read and quick queries, the following sections with a example of 4 -channel digital hard disk recorders to intro du cethe detail s, and pictures are base on this model, other model’s operation interface are the same except channel and frame rate, Corresponding parameter to the same settings, individual parameters can be directly and so on .

8

2.

2. Basic

Basic

Basic function

function

function operation

operation

2.1

2.1 On/off

On/off

On/off Switching

Switching

Switching navigation

navigation

2.1.1

2.1.1 S

S

S tart

tart

Before start ， Please ensure all parts connected well ！ Power on Equipment start ， POWER indicator light is red.

2.1.2

2.1.2 Power

Power

Power off

off

User can power off the device by using remote controller 、 keyboard and mouse.

2.1.3

2.1.3 By

By

By remote

remote

remote controller:

controller:

P ress Power button, the Shut down window will appear, click OK, the unit will power

off after a while.

2.1.4

2.1.4 D

D

D isconnect

isconnect

isconnect the

the

the power

power

power b

b

b y

y

y keyboard

keyboard

keyboard and

and

and mouse

mouse

mouse :

Step1: enter into Menu, then select “ System Shut Down ” icon, the Shut down window

will appear

Step2: click OK, the unit will power off after a while. Step3: disconnect the power

2.2

2.2 Login

Login

Equipment start , 【 POWER 】 indicator light bright . initial password is blank . After

equipment start press 【 MENU 】 key on panel or press right key on mouse

,

trun to login

interface as below :

P ic 2 -1 User login

After Input matching user name and password ,you can enter system to setup and operation .

Live preview interface:

9

�

� Live

Live

Live playback

playback

Click Playbutton to playback the record enter fast record playback : as lelow

picture:User can do concrete operation by click the buttons on screen .

2.3

2.3 Main

Main

Main menu

menu

menu setup

setup

setup guide

guide

Menu

Menu bar:

bar:

bar: Click right mouse or press ESC button on the front panel, the control bar

will display on the bottom of the screen, refer to p ic2-2

P ic 2-2 Menu bar

Click the icon near Screen mode , appear channel choose frame as below

Icon

Sign

Sign description

description

R ecording

Manual record

M otion detectio n stat e

Alarm state

Timing recording stat e

10

P ic 2 - 3 Channel choose

user could choose 1 channels from 1- 4 to show live video.click to save .

Click function menu ， will show dialogue frame as Pic 2 - 4;

Pic 2 - 4 M ian function

C lick “ configuration management ” ， display syswindows as pic 2 - 5:

Pic 2-5 Configuration management ”

Press MENU button on the front panel or the same button on remote control,

also cuold display the same window.

2.4

2.4 Configuration

Configuration

Configuration management

management

Configuration Management contains nine sub-menu: basic configuration, on-site configuration, video configuration, recording plan , alarm configuration, network configuration, user management, PTZ configuration and advanced configuration .

11

2.4.1

2.4.1 Basic

Basic

Basic configuration

configuration

Click “ Basic configuration ” ， show window as pic2-6, The basic configuration

contains two sub-menu: system date and time

1)

1) system

system

Pic 2-6 System

I n this interface user can setup the device name, device ID, video format , Video

Output and language, Screensaver and so on. The definitions for every parameters display as below:

Device

Device name:

name:

name: It may display on the client end or CMS that help user to recognize the

device remotely.

Device

Device number

number

number : Corresponding with the remote control number

Video

Video format:

format:

format: two modes:

PAL

and NTSC. User can select the video format according

to that of camera.

Password

Password check:

check:

check: Enable this option. user needs to input user name and password

can do corresponding operations with the relevant right in system configuration.

Show

Show system

system

system time

time

time ： choose display time in live or not

Video

Video output:

output:

output: the resolution of live display interface, range from: VGA800*600,

VGA1024*768, VGA1280*1024,HDMI 1080P. and HDMI 720P

Language

Language : setup the menu language : Simplified Chinese , Traditional Chinese ,

English,Japanese, German ,Russian,French,Portuguese,Turkish,spanish,Italian,Polish, Hungarian,Slovak,Vietnamese,greek

Click the "Default" button, the system restore the default things

;

C lick the "Apply" button will save the above settings; click the " E xit"button to exit the

current interface , Tip to change the menu language and video output, the device will restart

.

2

2 )

)

) Time

Time

Time &

&

& date

date

Pic 2-7 Time & date

S et the date format, time format time zone at the date and time "interface,; check the"

Keep synchronized with network time server "to update the network time server.

You

can

alsomanually adjust the system time .

12

Note:

Note: The system default is GMT time zone, please choose GMT +8 in the time

zone drop-down frame.

Click the "Default" button, the system restore the default settings;

C lick the "Apply" button will save the above settings;

C lick the " E xit"button to exit the current interface.

2.4.2

2.4.2 Live

Live

Live configuration

configuration

Click “ Live

Live

Live configuration

configuration

configuration ” ， enter window as pic2-8

Live configuration includes two submenus : live and mask

2.4.2.

2.4.2. 1

1

1 Live

Live

Live configuration

configuration

Pic 2- 8 Live configuration

Note:

Note: Click Camera Name to see a soft keyboard. User can choose

different character format to input .

.

click “ D efault”button to resort default setting, click “ OK”button to save the setting. user can setup all channels with same parameters, please tick off “ all ” and then do relevant setup.

2.4.2.2

2.4.2.2 Mask

Mask

P rivate mask . User can setup private mask area on the live image picture ,

Pic 2- 9 M ask

Setup

Setup mask

mask

mask area:

area:

area: click Setting button, enter into live image to press left mouse and

drag mouse to set mask area, refer to below picture. Click Apply button to save the setting. ；

Delete

Delete mask

mask

mask area:

area:

area: select a certain mask area, click left mouse to delete that mask

area, click Apply button to save the setting.

13

Live image mask area

2.4.2.3

2.4.2.3 video

video

video input

input

Pic 2-1 0 M ask

Users can choose the type of camera,rang form:1080P 、 720P 、 1080I.

2.4.3

2.4.3 Record

Record

Record configuration

configuration

Click “ Record

Record

Record configuration

configuration

configuration ” ， enter window as pic2-11 ：

Record configuration includes four sub menus: start , record bit rate, Character

overlay.recycle record .

2.4.3.1

2.4.3.1 Start

Start

Pic

2-11

Start

14

T

ick off record channel , channel audio

.

U ser can setup all channels with same parameters, tick off “ A ll ”,then to do relevant

setup.

C lick

“

D efault ” button to resort default setting; click “ A pply ” button to save the setting;

click “ E xit ” button to exit current interface .

Video parameters instruction

2.4.3.2

2.4.3.2 R

R

R ecord

ecord

ecord bit

bit

bit rate

rate

Pic 2- 12 R ecord bit rate

S etup rate, resolution, quality, encode and max bit stream

U ser can setup all channels with same parameters, tick off“All ” , then to do relevant

setup.

C lick “ D efault”button to resort default setting; click “ A pply ” button to save the setting;

click “ E xit ” button to exit current interface.

2.4.3.3

2.4.3.3 Record

Record

Record stream

stream

stream introduce

introduce

Stamp

Stamp ：

：

： User can overlap the channel name and time stamp on video .

Parameter

Parameter Meaning

Meaning

start Every channel record switch audio Start use the channel record audio

Parameter

Parameter Meaning

Meaning

F ps Range from 1-30 （ NTSC ） 1-25(PAL) Resolution Support 1080P 、 720P 、 D1 、 CIF

Quality

The higher the value is, the clearer the Recorded image is. Six options ： lowest , lower , low, medium, higher and highest.

Coding Support CBR and VBR

Max bitrate

Select range ： 64Kb 、 128kb 、 256 Kb 、 512Kb

、

1024Kb 、 1536kb 、 2048Kb,3072 Kb, 4096Kb,5120 Kb,6144 Kb,7 1 68 Kb, 8192 Kb

15

Pic 2-13 Character overlay

T

ick off camera name, time stamp; click Setting button, and then user can use cursor to drag the camera name and time stamp in random positions. Please refer to below Figures U ser can also setup all channels with same parameters.

C lick “ D efault ” button to resort default setting; click “ A pply”button to save the setting;

click “ E xit ” button to exit current interface

2.4.3.4

2.4.3.4 Recycle

Recycle

Recycle record

record

T

ick off recycle record to enable the recycle record function. It will cover the earlier recorded files and keep recoding when HDD is full; if disenabled, it will stop recording when HDD is full. Note: general the image quality, frame rate and resolution parameters setting higher,the more take up disk space

.

C lick “ D efault”button to resort default setting; click “ A pply ” button to save the setting;

click “ E xit ” button toexit current interface.

2.4.4

2.4.4 Schedule

Schedule

Schedule configuration

configuration

Schedule configuration includes two sub menus: schedule 、 motion and sensor.

2.4.4.1

2.4.4.1 Schedule

Schedule

The volume means the seven days of a week from Monday to Sunday; the row means 24 hours of a day. Click the grid to do relevant setup. Blue means checked area, gray means unchecked area.

Pic 2-14 S chedule

Copy

Copy ： User can apply the schedule setting of certain channel to other or all channels.

Just only select channel and click “ Copy ” button

.

C lick “ D efault”button to resort default setting; click “ A pply ” button to save the setting; click “ E xit ” button to exit current interface.

16

2.4.4.2

2.4.4.2 Motion

Motion

Pic 2-15 Motion

T he setup steps of motion are familiar with schedule

Note:

Note: the default schedule of motion detection is full-selected, that is, the color of

schedule setting interface is blue

.

2.4.4.3

2.4.4.3 Sensor

Sensor

Pic 2-16 Sensor

T he setup steps of alarm are familiar with schedule

Note:

Note: the default schedule of sensor is full-selected, that is the color of schedule

setting interface is blue.

2.4.5

2.4.5 Alarm

Alarm

Alarm configuration

configuration

Alarm configuration includes five sub menus: sensor, motion, video loss and alarm out

.

2.4.5.1

2.4.5.1 Sensor

Sensor

Sensor includes t wo sub menus: basic, alarm

1

1 >

>

> Basic

Basic

17

Pic 2-17 Sensor - Basic

E nable sensor alarm and set the alarm type according to triggered alarm type. Two

option: low level and high level

U ser can setup all channels with same parameters, please tick off“A ll ” , and then to do

relevant setup.

C lick “ D efault ” button to resort default setting; click “ apply”button to save the setting;

click “ E xit ” button to exit current interface.

2>

2> Alarm

Alarm

Alarm handling

handling

Pic 2-18 alarm handling -alarm configuration-sensor

S elect hold time and click setting button. Then a dialog box will pop-up as below ：

Pic 2-19 alarm handling - alarm configuration

18

A larm configuration: in the alarm configuration interface can check the alarm way : audible alarm, trigger alarm and e-mail alarm

Trigger recording: check the trigger channel at "trigger video" interface,.Click "OK" to save the above settings, click "Exit" to exit the current interface channel .

Alarm linkage: set the alarm type and linkage type at linkage alarm interface, such as preset positions, cruise line or track (Note: these three is already applicable in before PTZ configuration, click "OK" to save above settings when the corresponding channel alarm input, PTZ start a preset point,cruise lines and trajectories. Click "Exit" to exit the current interface .

Pic 2-20 Alarm handling - alarm linkage

U ser can setup all channels with same parameters, please tick off“A ll ” , and then to do relevant setup. 。

C lick “ D efault”button to resort default setting; click “ A pply ” button to save the setting; click “ E xit ” button to exit current interface.

2.4.5.2

2.4.5.2 Motion

Motion

Motion includes one sub menus: motion

1>

1> Motion

Motion

Pic 2-21 Motion

Click start motion alarm and set alarm hold time ， It refers to after close motion alarm it delay to the preset setting time. Click alarm "Settings" button, show below window ：

19

Pic 2-22 Alarm handling

Alarm configuration, trigger video alarm handling, linkage alarm handling and sensor alarm handling trigger settings is same.

C lick on " Area Settings" button at Motion detection interface, trun to the

following window ;

Pic 2-23 Motion detection - Regional Settings

At area Set ting interface, users can drag the slider to adjust the sensitivity value (1-5), the default value is 4 , 1-5 sensitivity progressive increase . Sensitivity influenced by the color

of time (day or night), the user s should ad just according to actual situation .click icon ，

set All locales for the detection region ； click icon ， will clear setting detection region

；

click icon ， save setting ； click button,exit from current interface.

U ser can setup all channels with same parameters, please tick off“A ll ” , and then to do relevant setup .

C lick “ D efault”button to resort default setting; C lick “ A pply ” button to save the setting; click “ E xit ” button to exit current interface.

2.4.5.3

2.4.5.3 Video

Video

Video loss

loss

20

Pic 2-24 Video loss

Click “ A larm handling ” button ， turn to window as below ：

Pic 2-25 Video loss - alarm handling

T he setup steps of video loss trigger are familiar with alarm handling

.

U ser can also setup all channels with same parameters ，。 click “ A pply”button to save the setting; click

“

E xit”button to exit current interface.

C lick “ D efault”button to resort default setting ； Disconnected from the network: when the network connection is disconnected, the system will automatically sent E-mail to the user specified mailbox about the network disconnected.

2.4.5.4

2.4.5.4 Alarm

Alarm

Alarm out

out

Alarm out includes two sub menus: alarm out, and buzzer .

.

1>

1> Alarm

Alarm

Alarm out

out

Pic 2-26 Alarm out

In this interface, set relay alarm out name, select hold time which means the interval

time between the two adjacent alarms

U ser can setup all channels with same parameters. Tick off “ A ll ” to do relevant setup. click “ D efault”button to resort default setting ； click “ A pply”button to save the setting; click “

E xit”button to exit current interface.

2>

2> Buzzer

Buzzer

At buzzer interface ， tick off Buzzer, set buzzer alarm hold time

2.4.6

2.4.6 Network

Network

Network configuration

configuration

Network configuration includes four submenus: network, sub stream, Email and other

settings

.

2.4.6.1

2.4.6.1 Network

Network

21

Pic 2-27 Network configuration

HTTP

HTTP port

port

port ： the default value is 80. If the value changed, user needs to add the port

number when typing IP address in IE address blank.IE set HTTP port to 82, IP address: http://192.168.0.25,user needs to input that address: http://192.168.0.25:82 into IE browser .

Server

Server port

port

port : data and image communication port NO. After selecting the "Obtain an

IP address automatically", the device will distribute IP address, subnet mask, and gateway IP and DNS server.

E nable PPPoE to directly connect the DVR to internet via ADSL and then input the user name and password; click TEST button to test the effectiveness of the relevant information.

C lick “ D efault ” button to resort default setting ； click “ A pply”button to save the setting;

C lick

“

E xit”button to exit current interface

.

2.4.6.2

2.4.6.2 Network

Network

Network Sub

Sub

Sub stream

stream

Pic 2-28 Network Sub strea

select fps, resolution, quality. ， user can also setup all channels with same parameters

. click “ A pply ” button to save the setting; click “ E xit ” button to exit current interface. network configuration-network

.

Parameter

Parameter Meaning

Meaning

FPS

Range from: 1-30 （ NTSC ） 1-25(PAL)

Resolution

Support D1 、 CIF

Quality

Quality The higher the value is, the clearer the record image. Six

options: lowest, lower, low, medium, higher and highest.

22

2.4.6.3

2.4.6.3 Email

Email

Pic 2-29 Email

SMTP

SMTP Server/Port:

Server/Port:

Server/Port: the name and port number of SMTP server

.

Send

Send address/password:

address/password:

address/password: sender’s email address/password .

Receive

Receive address:

address:

address: receiver’s email address . Here user can add at least three mail

addresses

.

Click

T

est button to test the validity of the mailbox .

C lick

“

D efault ” button to resort default setting ； click

“

A pply ” button to save the setting;

click “ E xit ” button to exit current interface.

2.4.6.4

2.4.6.4 Other

Other

Other settings

settings

Pic 2-30 Other settings

Enable DDNS server: user needs to input user name ，

，

， password and host domain

name of the registered website, click TEST to test the effectiveness of the relevant information. click “ D efault ” button to resort default setting; click

“

A pply ” button to save the

setting; click “ E xit ” button to exit current interface.

Note

Note : the user select a domain name is bound by the Domain Name Service for DVR,

you must first landing the website of the ISP registered user name and password, and then apply for a domain name for the server online. After the application is successful, the user could enter the domain name to access the server in IE side .

2.4.7

2.4.7 User

User

User management

management

23

Enter User management , as below pic ：

Pic 2-31 User management

C licking Add button, a dialog box will pop-up as below ：

Pic 2- 32 General

1 General: Input user name, password; select user type, input the MAC address of

the PC; click OK button, this user will be added into the user list box; click Exit button to exit the current interface .

2 Authority:

Pic 2-33 Authority: In the authority interface, assign the definite operation right for that user . I n the user management interface, click Setup button to modify user name, user type

and binding PC MAC address.

S elect the user that user wants to delete in the user list box and then click “ Delete ”

button to delete this user. click Change password button to modify the password and then click “ Exit ” button to exit the current interface.

24

2.4.8

P.T.Z

configuration

P.T.Z

configuration includes two submenus: serial port and advance

2.4.8.1

2.4.8.1 serial

serial

serial port

port

Pic 2-34 S erial port

Click “ Start ” ， base on

P.T.Z

support Protocol to set Address , Baud rate ,and Protocol

.

U ser can setup all channels with same serial port parameters, please tick off “ A ll ”,and then to do relevant setup. click “ D efault ” button to resort default setting; click “ A pply ” button to save the setting; click “ E xit ” button to exit current interface .

Definitions

Definitions and

and

and descriptions

descriptions

descriptions of

of

of serial

serial

serial port:

port:

2.4.8.2

2.4.8.2 Advance

Advance

Advance configuration

configuration

Pic 2-35 Advance

Parameter

Parameter Meaning

Meaning

Address The address of the PTZ device Baud rate Baud rate of the PTZ device. Range form: 110, 300, 600, 1200,

2400, 4800, 9600, 19200, 3 84 00, 57600, 115200, 230400, 460800, 921600.

Protocol Communication protocol of the PTZ device. Range from:,

PELCOP , PELCOP1, PELCOP5, PELCOD, PELCOD1,

HY, PHILIPS, SAMSUNG SHARP,SONY , SAMSUNG, PANASMIC , C ONTROL l , etc …

25

I n the Advance interface, after clicking preset “ Setting”button, a dialog box will

pop-up as below ：

Pic 2-36 Preset point setting

I n the preset set interface, click Setting button to see a window as below ：

Pic 2-37 P reset set ting

U ser can control the

P.T.Z

up, up left, down, right down, left , left down, right and up right and stop rotating ； can adjust the rotation speed of the PTZ , focus and aperture ； choose preset arrange NO. Click “ Save ” button to save the settings ， click icon to hide the tool bar, right-key can remerge it ； click icon to exit the current interface

I n the preset interface, click

”

OK ” button to save the setting; click ” Exit ” button to exit

current interface.

I n the Advance interface, click cruise “ Setting ” button, a dialog box will pop-up as

below ：

Pic 2-38 Advance - cruise

“

Setting ”

C lick Add button to add cruise line （ max 32 cruise line can be added ）； select a cruise

line and click Setup button, to see a window as below ：

26

Pic 2-39 C ruise set-preset point setting

C lick Add icon ， to set the speed and time of preset point; select a preset point and

click Delete icon to delete that preset poin ； click Modify icon ， to modify the setting of a preset point ； User can click those icons to adjust the position of preset point.top 、 up 、 down and bottom 。 Click Preview button to preview the cruise line and then click

“

OK ” button to save the setting. Next, click “ Exit ” button to exit current interface

S elect a preset point in the cruise line list box and click Delete button to delete that cruise line; click “ Clear all ” button to clear all cruise line from the list box; click “ OK ” button to save the setting; click “ Exit ” button to exit current interface.

I n the Advance interface, click track “ Setting ” button to pop up a dialog box as below ：

Pic 2-40

T

rack setting

U ser can control the dome rotates up, up left, down, right down, left, left down, right and up right and stop rotating . adjust the rotate speed and the value of zoom, focus and iris of the dome ； click Start Record button to record the move track of PTZ and click this button

again can stop record ； click Start track button to play recorded track and click this button again can stop play . The user can drag the slider to adjust the rate of

P.T.Z

movement .

C lick icon to hide the tool bar, right-key can remerge it ; click icon to exit the current interface.

I n the Advance interface, click “ D efault”button to resort default setting; click “ A pply ” button to save the setting; click

“

E xit”button to exit current interface.

27

2.4.9

2.4.9 A

A

A dvance

dvance

dvance configuration

configuration

Advanced settings include three sub-menu: factory settings, andimport / export and

exit .

1. Factory settings: all settings back to factory settings .

2. Import/Export: Users can export data files to be backed up onremovable storage devices, you can also import the specified data file from a removable storage device to a DVR.

3. Exit: exit current interface .

Pic 2-41 A dvance configuration

Returned to the main menu, enter the data retrieval interface .

2.5

2.5 D

D

D ata

ata

ata retrieval

retrieval

Search configuration includes two submenus: Time Search, Event Search,

2.5.1

2.5.1 Time

Time

Time search

search

Step1 ： enter into Search configuration � Time Search; refer to below pic ：

Pic 2-42 Time search

Step 2 ： Select the channel, the calendar date , the start time and end time Step 3 ： click “ Play ” button, Playback will start from the set time bucket;click the

corresponding button on the screen to start concrete operations.

28

Pic 2-43 Playback buttons

2.5.2

2.5.2 Event

Event

Event search

search

Step1: ： enter into Search configuration � event search; refer to below pic .

Pic 2-44 Event search

Step2 ： After clicking Search button, the searched event information will displayed in

the event list box , double check a certain record file to playback.

Step 3 ： User can select date, channel. Tick off Motion, Sensor or All accordingly to

search .

29

2.6

2.6 Backup

Backup

This unit supports backup by USB device ， User also can make backup by IE browser

via internet .

Step1: enter into backup configuration interface , as below pic ：

Pic 2-45 Data backup

Step2: set the start & end time, select channels and click Search button to display the

searched data in the data backup list box .

Step3: checked a data file or tick off “ All ” to select all data files, click “ Backup ” button, Step4: in the backup information interface, user can check the relevant information of

backup files, storage type, save file type, etc. click “ Start ” button to starting backup.

2.7

2.7 Check

Check

Check information

information

Through this option, the user can check system information, system journal , network

information

System

System Information

Information

:

E nter menu

�

view information

�

system information ， in the interface user can view

the equipment and version information and relevant information

Log

Log information

information

information :

:

E nter menu

�

View system information

�

Log information ， in the interface users can set the start & end time of log you want to view, select the type of log you want to view and click the search button, search ed the log information will be displayed in the log list box .

Note:

Note: Users can export data files to be backed up on removable storage devices.

Network

Network information

information

information :

:

E nter menu � view information � Network configuration ， in the interface ， Users

can view the relevant parameters of the network information .

2.8

2.8 Disk

Disk

Disk management

management

E nter menu � Disk management ， In the interface, the user can

view disk storage state, also can choose to format ting the hard disk

P lease format the hard disk before record , Specific operation as below ： . Step1: enter into disk management interface ， The system will pop up the Disk

Management window .

Step 2 : select a hard disk and click Format button to star format. ； set the property of the

disk then click “ Apply”button to save the setting

.

Note:

Note: all recorded files in the hard disk will be lost after formatted .

30

2.9

2.9 Upgrade

Upgrade

Once have the new version, the user can choose to upgrade the panel and the

mianboard, can get upgraded software from the buyers, to upgrade the system .

Upgrade

Upgrade step

step

step ： user needs to copy the upgrade software which get from vendor into

the USB storage device and then connect to the USB port. Enter Menu Upgrade ， refresh list

，

the upgrade software name is displayed in the upgrade list box, select that software and click Upgrade button to start upgrading . System will automatically restart on the upgrade process

，

Please wait for a while when the system is rebooted. Please don’t cut off power during upgrading . This system supports the upgrade of the USB device but it must be compatible with the USB device , need to reboot the system after the upgrade completed to take effect.

Note:

Note: If the upgraded software does not appeared in USB, usually the USB

devices are not compatible

.

2.10

2.10 Logoff

Logoff

Enter Menu � Logoff

Logoff

Logoff ， Click Log off icon,The system will exit the current user login. If

user wants to log in again, click mian menu icon to enter into user name and password to re-login.

2.11

2.11 System

System

System shut

shut

shut down

down

C lick “ system shut down ” icon , shut down system .

Footprint Security H.264 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual