Fisher & Paykel WD8560F1, WD8060P1, WD7560P1 User Manual

0 (0)

INSTALLATION INSTRUCTIONS

USER GUIDE

Front Loading Washer Dryer

WD8560F1, WD7560P1 and WD8060P1 models

NZ AU GB

CONTENTS

 

 

 

Introduction

3

Safety and warnings

4

Installation instructions

9

Before you do your first wash

17

Getting started quickly

18

Washer dryer controls

20

Safety features

22

Sorting and loading

23

Detergent and fabric softener

27

Wash and dry cycles

30

Wash and dry cycle options

32

Customising wash and dry cycles

36

Caring for your washer dryer

37

Before you call for service

40

Fault codes

42

Troubleshooting

43

Consumption data table

51

Product Fiche according to Commission Delegated Regulation (EU) 96/60/EC

52

Manufacturer’s Warranty

53

Customer Care

55

European Directive 2012/19/EU on Waste Electrical

57

and Electronic Equipment (WEEE)

 

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this user guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

Registration

Register your product with us so we can provide you with the best service possible.

To register your product visit our website: www.fisherpaykel.com

1

INTRODUCTION

Welcome

Thank you for buying a Fisher & Paykel washer dryer. We are proud of this washer dryer and trust it will serve you well for many years.

Your washer dryer gives you the ultimate convenience in one simple machine. There are numerous wash, dry and continuous wash and dry cycles with additional options, meaning you can perform every wash and dry task with ease and have the knowledge that your clothes are receiving the best possible care.

With the ability to automatically sense when your clothes are dry, your washer dryer is more efficient, making it kinder on your wallet and the environment. Having the technology of a water condensing dryer allows clothes to be dried in a closed environment where the hot moist air is condensed and pumped directly into a drain, therefore requiring no external ventilation.

At Fisher & Paykel we aim to provide innovative products that are simple to use, ergonomic and that will exceed expectations. Thousands of tonnes of laundry and

80 years of experience have been programmed into your washer dryer to help give you the best possible performance.

Please take the time to read these instructions carefully before you begin using your machine. Following the advice in this user guide will ensure you get the performance you expect from your machine with the best possible wash and dry results. Keep these instructions for future reference.

We hope you enjoy your new washer dryer. We have certainly enjoyed designing it for you.

Front loading washer dryer

3

Fisher & Paykel WD8560F1, WD8060P1, WD7560P1 User Manual

SAFETY AND WARNINGS

Caution, risk of fire — this is a safety symbol. Failure to follow the warnings outlined in these user instructions can cause a fire hazard.

!WARNING!

Fire Hazard

Only dry fabrics that have been washed with water.

Do not use heat to dry articles containing foam rubber or similarly textured rubber– like materials, dry on ‘Air Dry’.

Do not stop a washer dryer before the end of the drying cycle unless all items are removed and spread out in order to dissipate the heat.

A washer dryer produces combustible lint; clean pump filter regularly.

Failure to follow these instructions can result in death or personal injury.

!WARNING!

Electric Shock Hazard

If you are using an extension cord or a portable electrical outlet device

(eg multi-socket outlet box), ensure that it is positioned so that it does not come into contact with water or moisture.

Failure to do so may result in death or electrical shock.

4

SAFETY AND WARNINGS

IMPORTANT SAFETY INSTRUCTIONS

WARNING!

When using your washer dryer, follow basic precautions, including the following:

CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance

must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

This washer dryer is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are supervised or given instructions on how to use the washer dryer by someone responsible for their safety.

The washer dryer should only be used for washing, rinsing and drying of textiles where this is indicated on the care label.

The door will be locked from the start of the cycle until the cycle is complete for safety reasons. It is possible to open the door during the cycle under certain conditions (refer to page 20).

Never force the door open.

Keep children away from the washer dryer while it is in operation.

Supervise children to ensure they do not play with the washer dryer or climb inside the drum.

Do not touch the door during a drying cycle as the door can become hot.

Do not open the detergent dispenser during the cycle.

The only user-removable parts of the washer dryer are the inlet hose, detergent dispenser and the pump

5

SAFETY AND WARNINGS

filter. No other parts are designed to be removed by anyone other than a Fisher & Paykel trained and supported service technician.

When disposing of the washer dryer, it is recommended that the door is removed to avoid children getting trapped inside, and that the electrical cable is cut off close to the washer dryer.

Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapours that could ignite or explode.

Do not wash or dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances as they give off vapours that could ignite or explode.

Undergarments that contain metal reinforcements should not be placed in the washer dryer. Damage to the machine can result if the metal reinforcements come loose during washing or drying.

Check and remove all objects from pockets, eg lighters and matches.

The maximum mass of dry textile material is four kilograms (WD7560P1 and WD8060P1 models) or five kilograms (WD8560F1 model). Do not overload your washer dryer.

Never wash or dry rubber articles, fibreglass, or any plastic items or film, eg plastic lined tablecloths and baby bibs.

Clothes must go through the cool down/airing phase in the final part of the drying cycle. This ensures items are left at a temperature where they will not be damaged. If for any reason the washer dryer is stopped before the cycle has finished, dry clothes

6

SAFETY AND WARNINGS

should be removed immediately and not left in the dryer. Clothes should be quickly spread out flat to cool so heat can dissipate, not left bunched up, eg in a clothes basket.

• This washer dryer has been designed for domestic use only, not for commercial applications, such

as massage/beauty clinics where there may be increased lint accumulation or flammable materials in the atmosphere or load.

• Do not operate this product if there is an accumulation of lint in or around the washer dryer.

• Children should be supervised to ensure they do not play with the washer dryer.

• Unplug the machine from the power supply when it is not in use.

• Do not swing or put weight on the door.

• Your washer dryer is designed to stop operating in the event of power outage. When power is resumed, the machine will remain off until the ‘POWER’ button is pressed. To restart the washer dryer, press ‘POWER’, select your wash or drying cycle and touch .

• Never attempt to repair the washer dryer yourself.

• For problems that cannot be solved from information in this user guide, turn off and unplug your washer dryer and contact a Fisher & Paykel trained and supported service technician.

Spontaneous combustion

IMPORTANT!

To reduce the risk of fire in a washer dryer the following should be observed:

• Items that have been spotted or soaked with vegetable oil or cooking oil are a fire hazard and

should not be placed in a tumble washer dryer.

7

SAFETY AND WARNINGS

Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as a washer dryer. The items become warm causing an oxidation reaction in the oil. This oxidation creates heat. If the heat cannot escape the items can become hot enough to catch fire. Piling, stacking or storing oil-affected items can prevent heat from escaping creating a fire hazard.

Fabrics that contain vegetable oil, cooking oil or have been contaminated by hair care products should not be washed or dried. If unavoidable, these fabrics should be washed in a hot water wash with extra detergent — this will reduce, but not eliminate the fire hazard. The cool down cycle of the washer dryer should be used to reduce the temperature of these items. They must not be removed from the washer dryer and piled or stacked while hot.

Items that have previously been cleaned in, washed in, soaked in or spotted with flammable liquids or solids, eg petrol/gasoline, kerosene, dry cleaning solvents, vegetable or cooking oil, acetone, denatured alcohol, some brands of spot removers, turpentine, waxes and wax removers or other flammable or explosive substances should not be placed in a washer dryer.

Do not dry unwashed items in the washer dryer.

Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.

The washer dryer must not be used if industrial chemicals have been used for cleaning.

8

INSTALLATION INSTRUCTIONS

Please read and follow the ‘Safety and warnings’ and ‘Installation instructions’ sections carefully before using your washer dryer!

Accessories

Please check you received the following accessories with your Fisher & Paykel washer dryer. You will find them inside the drum:

●●1 x Inlet hose

●●1 x Drain hose guide

●●1 x Installation instructions and user guide

●●1 x Spanner

●●1 x Installation leaflet (attached to the top of the washer)

●●1 x Hose clamp (WD8060P1 model only)

Unpacking

To ensure the best performance from your new washer dryer please follow the instructions below.

Removing the packaging

1Remove the outer packaging (including the polystyrene packer and plastic wrapping). All packaging must be removed prior to use. Ensure these materials are kept out of reach of children. Note: a small amount of water may be seen inside the packaging and inside the washer dryer. This is the result of factory testing and is normal.

2Tilt the product backwards and ‘walk’ it off the base one foot at a time. Not doing so may cause damage to your floor and washer dryer.

3Remove all packaging and accessories from inside the drum.

Removing the transit bolts

The clothes washer dryer is fitted with 4 transit bolts at the rear to prevent internal damage during transportation.

IMPORTANT!

●●The 4 transit bolts MUST be removed prior to operation of the machine. Failure to remove these will result in damage to the product.

●●Ensure packaging materials are kept out of reach of children.

●●Please help protect the environment and dispose of the packaging from around the washer dryer in an environmentally friendly manner.

9

INSTALLATION INSTRUCTIONS

To remove the bolts:

1Use a spanner or socket to unscrew and remove all four transit bolts at the back of the washer dryer (A).

2Pull the black rubber grommets to remove the bolt, grommet and white plastic spacers from the machine. Keep the transit bolts in case they are required for future transit of the machine. Never transport the machine without the transit bolts properly fixed in place.

3Cover the bolt holes with the white plastic plugs which are attached to the machine and located near each hole (B). Push to clip into place.

A

Removing the transit safety bolts

B

Installation location

IMPORTANT!

●●The washer dryer must be installed in a well-ventilated, dust-free environment.

●●The washer dryer must not be installed on any textured floor coverings (eg carpet, rugs) to ensure that openings at the base of the machine are not obstructed.

●●Do not install the washer dryer behind a lockable door, sliding door, or behind a door where the hinge is on the opposite side to that of the washer dryer in such a way that the full opening of the door is inhibited. Ensure the washer dryer door can always be opened fully.

Note: this washer dryer CANNOT BE INVERTED AND MOUNTED ON THE WALL.

10

INSTALLATION INSTRUCTIONS

Product dimensions

C

E

A

D

B

FRONT VIEW

Wall

TOP VIEW

 

 

WD7560P1

 

WD8060P1

 

WD8560F1

 

 

 

 

 

 

 

PRODUCT DIMENSIONS

 

mm

 

mm

 

mm

 

 

 

 

 

 

 

A Overall height of product

850

850

850

 

 

 

 

 

 

 

B Overall width of product

600

600

600

 

 

 

 

 

 

 

C Overall depth of product

590

590

645

(including dial and door

 

 

 

 

 

 

when closed)

 

 

 

 

 

 

 

 

 

 

 

 

 

D Depth with door open

1010

1010

1065

 

 

 

 

 

 

 

E Minimum door clearance to

330

330

330

adjacent wall

 

 

 

 

 

 

 

 

 

 

 

 

 

Standpipe height

 

min. 800 – 1200

 

min. 800 – 1200

 

min. 800 – 1200

MAXIMUM CAPACITY

 

kg

 

kg

 

kg

 

 

 

 

 

 

 

Wash capacity

7.5

8.0

8.5

 

 

 

 

 

 

 

Dry capacity

4.0

4.0

5.0

 

 

 

 

 

 

 

Note: the exact height of your washer dryer is dependent on how far the feet are extended from the base of the machine. The space where you install your washer dryer needs to be at least 40mm wider and 20mm deeper than its dimensions.

11

INSTALLATION INSTRUCTIONS

IMPORTANT!

This machine must not be installed and operated on a plinth.

Levelling the machine

It is IMPORTANT to level the machine to ensure good spin performance, and to minimise noise, vibrations and wear and tear on the washer dryer.

1Before positioning the machine in its final position, check that the machine is level, front to back and side to side.

2Manoeuvre the product into its final position (we suggest a minimum clearance of 20mm each side).

3Use a spirit level to check that the machine is correctly level. The washer dryer comes with four adjustable feet, wind all four feet up or down until the dryer is correctly level. Place the spirit level on top of your washer dryer in the following places;

●●left to right,

●●back to front,

●●corner to corner.

The machine is considered level when the bubble sits in the centre of the two lines when placed flat on top of the machine.

4Using the spanner provided, tighten the lock nuts against the base of the machine to lock the feet in position.

Never unscrew the feet completely from their housings.

After levelling, the corners of the washer dryer cabinet should be clear of the floor and the machine must not rock in any direction.

Levelling the feet

Locking the feet

12

INSTALLATION INSTRUCTIONS

Connecting to the water supply

Inlet hose

IMPORTANT!

●●A new hose is provided with the washer dryer and should be used to connect the washer dryer to the water mains.

●●Old hoses should not be re-used.

●●We recommend that the inlet hose be changed every 5 years. WARNING: Failure to do so may result in a flood and damage to property.

Straight

Elbow

(tap) end

(machine) end

Inlet hose ends

1Connect the straight end of the inlet hose to the cold tap and the elbow end to the machine inlet valve. Tighten the inlet hose end by hand until the hose seal just makes contact with the tap sealing face and then tighten a further half-turn. Make sure there are no kinks in the hose.

2Turn the tap on and check for leaks. Check for leaks again after 24 hours.

IMPORTANT!

The cold water temperature should not exceed 35°C.

Water supply requirements:

●●Inlet water pressure: Maximum 1000kPa (150psi), Minimum 30kPa (4.5psi)

●●Inlet water flow rate: Minimum 6 litres/minute

Note: an internal heater in the product will heat the cold water to the selected cycle temperature.

13

INSTALLATION INSTRUCTIONS

Draining

Drain hose placement in a stand pipe or tub

1To guide the drain hose over the tub or standpipe the hose guide must be fitted to the drain hose. The height of the standpipe or tub should be between 800 – 1200mm.

2Secure the hose guide so it cannot become dislodged from the standpipe or tub.

IMPORTANT!

●●If the drain hose is placed on the ground or if the standpipe or tub is less than 800mm high, the machine will continuously drain while being filled (siphon).

●●Regularly check that your standpipe or tub is free from lint or other obstructions, which may affect how your machine works or may cause flooding.

Attaching drain hose to spigot

1Guide drain hose through hose guide

2Secure hose guide to back wall of cupboard using a screw. The height of the drain hose should be between 500 – 800mm from ground level.

3Attach drain hose to spigot and secure using a hose clamp ensuring the blanking insert is cleared from spigot.

4Check for leaks.

●●The drain hose should be checked from time to time and replaced if any damage (eg wear, cuts, bulges, kinks, leaks, etc) is found. Do not bend the drain hose sharply, as this may cause it to split.

●●In multi-storey apartments or any upper floor, the machine should be installed on a floor equipped with a drain.

●●Draining must comply with local by-laws.

Pull hose

 

through

(20mm)

guide

maximum

 

 

Standpipe 800 – 1200mm

Fitting the drain hose guide

Height 500 – 800mm from ground

Attaching drain hose to spigot

14

INSTALLATION INSTRUCTIONS

Electrical connection

1This appliance must be connected to a 220V – 240V, 50Hz, sinusoidal, minimum 10A electrical supply.

2Uncoil the power cord, remove and discard the plastic pin cover and plug into a wall socket.

3Connect the appliance to an earthed outlet protected by a fuse of suitable capacity.

●●Check the power cord for damage and make sure it is not squashed or twisted when installing the washer.

●●Always remove the power cord from a socket by the plug, not by the cord.

IMPORTANT!

●●If you are using an extension cord or a portable electrical outlet device (eg multi-socket outlet box), ensure that it is positioned so that it does not come into contact with water or moisture. FAILURE TO DO SO MAY RESULT IN DEATH OR ELECTRICAL SHOCK.

●●Do not touch or operate the machine with wet hands or with bare-feet.

●●A damaged power cord must be replaced by a Fisher & Paykel trained and supported service technician, in order to avoid a hazard. The appliance must not be operated until it is repaired, as there is a risk of electric shock.

●●Do not operate this machine if it has been damaged during transport. Contact your Fisher & Paykel dealer or Fisher & Paykel trained and supported service technician.

SPARE PARTS

Available from your Fisher & Paykel dealer or a Fisher & Paykel trained and supported service technician.

Hose Inlet Long (2m)

Part No. 422680P

 

 

Hose Inlet Large Bore

Part No. 426123P

 

 

Drain Hose Extension (not suitable for attaching to a spigot)

Part No. 425627P

 

 

15

INSTALLATION INSTRUCTIONS

Completing the installation

Installation test cycle

IMPORTANT!

Do this before you wash or dry any items in your washer dryer. This is to check that your washer dryer is installed and functioning correctly prior to use.

1Turn your washer dryer on by pressing the ‘POWER’ button.

2Select the ‘Quick Wash 30’ cycle. Ensure the drum is empty and the door closed.

3Touch the button. The machine will start to fill.

●●Observe the machine for any problems (eg leaking from the hose, excess noise or vibrations).

●●The washer will beep and display any faults on the screen if there are any problems. Refer to ‘Before you call for Service’ section at the back of this book.

4Wait until you see water in the bottom of the drum.

5Touch to stop the cycle, then press ‘POWER’ to turn the machine off.

6Press ‘POWER’ again, select the ‘Spin’ cycle and touch .

●●Check the drain hose is firmly secured to the standpipe or tub, or spigot.

●●Observe that the machine pumps out the water, and spins.

IMPORTANT!

If there are any problems, you must address these before proceeding with normal use. The washer dryer will automatically turn off at the end of the cycle if there are no problems.

16

Loading...
+ 42 hidden pages