Fisher Mounting Instructions for DVC6200/DVC2000 Digital Valve Controller on (Old NAMUR) Sliding Stem Actuator Manuals & Guides

www.Fisher.com

WARNING

may or may not

include all components shown for kit installation.

Mounting Instructions

DVC6200/DVC2000

Valve Controller on

(Old Namur) Sliding Stem Actuator

D103997X012
May 2014

Digital

Use these instructions to mount a FIELDVUE™
DVC6200 or DVC2000.

Avoid personal injury or property
damage from sudden release of process
pressure or bursting of parts. Before
performing any maintenance
operations:

 Always wear protective clothing,

gloves, and eyewear.

 Do not remove the actuator from
the valve while the valve is still
pressurized.

 Disconnect any operating lines
providing air pressure, electric power, or
a control signal to the actuator. Be sure
the actuator cannot suddenly open or
close the valve.

 Use bypass valves or completely
shut off the process to isolate the valve
from process pressure. Relieve process
pressure from both sides of the valve.

 Vent the pneumatic actuator
loading pressure and relieve any
actuator spring precompression.

 Use lock-out procedures to be sure
that the above measures stay in effect
while you work on the equipment.

 Check with your process or safety
engineer for any additional measures
that must be taken to protect against
process media.

Refer to the appropriate actuator instruction manual
for actuator installation, operation, maintenance, and
parts identification as this manual

1. Isolate the control valve from the process line

pressure and release pressure from both sides of the
valve body. Shut off all pressure lines to the actuator,
releasing all pressure from the actuator. Use lock-out
procedures to be sure that the above measures stay in
effect while you work on the equipment.

2. Install set screws into stem block.

3. Attach arm connector onto stem block set screws.

Two connecting arms are provided one suitable for use
with large actuators and one for use with small
actuators; select the appropriate one for the actuator
being used.

DVC6200/DVC2000

Digital Valve Controller on

(Old Namur) Sliding Stem Actuator

4. Loosely (for later adjustment) attach washers and

nuts to set screws.

Mounting Instructions

D103997X012

May 2014

6. Connect array to extension arm with supplied

fasteners. Leave fasteners loose enough for fine
adjustment.

7. Attach mounting bracket to actuator.

5. Attach extension arm to connector arm.

.

For Rib Actuator go to step 8a.

For Plane Actuator go to step 8b.

For Pillar Actuator go to step 8c.

DVC6200/DVC2000

(Old Namur) Sliding Stem Actuator

Mounting Instructions

D103997X012
May 2014

8a. Rib Actuator

Attach mounting bracket to actuator using supplied
M8 hex head fastener.

Skip to step 9.

8b. Plane Actuator

Attach mounting bracket to actuator using supplied
fasteners.

(4) M8X45 Hex Head Screws
(4) External Tooth Lock Washer
(4) M8 Hex Nuts

Digital Valve Controller on

8c. Pillar Actuator

Use hardware to attach mounting bracket to pillar.
Ensure device mounting plane is perpendicular to
array.

Hardware:

(2) M8 Round U Bolt

(4) External Tooth Lock Washer

(4) M8 Hex Nuts

Skip to Step 9

DVC6200/DVC2000

Digital Valve Controller on

(Old Namur) Sliding Stem Actuator

(Array Kit sold separately)

Ensure device mounting plane is perpendicular to
array.

9. Attach alignment template to mounting bracket.
Adjust array to line up with alignment template. If
Actuator stroke is in the up position, use Step 10a. If
Actuator stroke is in the down position, use Step 10b.
Ensure that the index mark of the alignment tool will
be in between the array index marks.

(Index Lines are shown below with arrows)

Mounting Instructions

D103997X012

May 2014

10a. Align array bottom index line with alignment
template index line.

10b. Align array top index line with alignment template
index line.

DVC6200/DVC2000

(Old Namur) Sliding Stem Actuator

Mounting Instructions

D103997X012
May 2014

11. Align array laterally with the alignment template.

12. Tighten all fasteners to lock array into position.
Loctite® Thread Locker 242® is recommended but not
supplied.

13. Remove alignment tool, and attach device to
mounting bracket with supplied M8 fasteners.

Digital Valve Controller on

(Device Mounted to Bracket Isometric View)

14. Double check that Array will travel without
obstruction in valley of device.

DVC6200/DVC2000

Digital Valve Controller on

(Old Namur) Sliding Stem Actuator

Bill of Materials

QTY

Description

4

2

2

4

3

2

1

2

2

2

1

1

1

1

2

4

1

Mounting Instructions

D103997X012

May 2014

Hex Head Cap Screw M8X1.25X45
External Tooth Lock Washer #8
Washer M4
Hex Nut M8X1.25
Hex Head Cap Screw M8X1.25X16
Hex Nut M6X1.0
Hex Head Cap Screw M8X1.25X25
Socket Head Cap Screw M4x12
Washer 6.4X12X1.6
Socket Head Cap Screw M6X1X20
Mounting Bracket
Arm Connector (A)
Arm Connector (B)
Arm Extension
U-Bolt M8X1.25X69
External Tooth Lock Washer M8
Array Kit (Sold Separately)

DVC6200/DVC2000

(Old Namur) Sliding Stem Actuator

Mounting Instructions

D103997X012
May 2014

Digital Valve Controller on

DVC6200/DVC2000

Digital Valve Controller on

(Old Namur) Sliding Stem Actuator

Mounting Instructions

D103997X012

May 2014

DVC6200/DVC2000

(Old Namur) Sliding Stem Actuator

Mounting Instructions

D103997X012
May 2014

Digital Valve Controller on

DVC6200/DVC2000

Digital Valve Controller on

(Old Namur) Sliding Stem Actuator

Air Filter Regulator

DVC6200

Mounting Instructions

D103997X012

May 2014

Common Mounting
Bracket

Alignment Template

Connector Arm

DVC2000

Extension Arm

Shield

Linear Feedback Array

Spacer

Insert Assembly

U-Bracket

DVC6200/DVC2000

Digital Valve Controller on

(Old Namur) Sliding Stem Actuator

Neither Emerson, Emerson Process Management, Fisher, nor any of their affiliated entities assumes responsibility for the selection, use and
maintenance of any product. Responsibility for the selection, use and maintenance of any product remains with the purchaser and end user.

Emerson Process Management

Mounting Instructions

D103997X012

May 2014

Fishe and FIELDVUE are marks owned by Fisher Controls International LLC, a member of the Emerson Process Management business unit of Emerson Electric Co.
Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their
respective owners.

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be
construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to
modify or improve the designs or specifications of such products at any time without notice.

Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Chatham, Kent ME4 4QZ UK
Dubai, United Arab Emirates
Singapore 128461 Singapore

www.Fisher.com

______________________________________________________________________________________________________

© 2014 Fisher Controls International LLC. All right reserved.