Files for HI120
Size:
683.48 Kb
Download

(1,1) -1-599489D izona vsisland install A2 NZGB.indd 21/7/09 2:51:59 PM

Installation instructions

IZONA VentSurface

HI120 ISLAND models NZ AU GB IE

Important!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our local website listed at the end of this document or contact your local Fisher & Paykel dealer.

1 SAFETY AND WARNINGS

WARNING!

Electrical shock hazard

Always disconnect the appliance from the mains electricity supply before carrying out any servicing or maintenance operations.

Failure to do so could result in electrical shock or death.

WARNING!

Cut Hazard

Take care - panel edges are sharp.

Failure to use caution could result in injury or cuts.

Important safety instructions!

To avoid hazard, read and follow these instructions carefully before installing or using this appliance.

Please make this information available to the person installing the appliance, as it could reduce your installation costs.

This appliance is to be installed and connected to the electricity supply only by a qualified electrician.

Installation must comply with your local building and electricity regulations. Failure to install the appliance correctly could invalidate any warranty or liability claims.

This appliance is designed for permanent fixture and has to be connected to the mains electricity supply.

The appliance must not be installed above cookers with eye-levelgrills. The appliance is heavy, take care when lifting or handling.

Before you install the appliance, please make sure that

the voltage (V) and frequency (Hz) indicated on the serial number plate as well as the specifications on the rating plate on the inside of the appliance correspond to the voltage and frequency of the mains supply.

the room in which the appliance is installed is well-ventilated.

the ceiling is able to withstand the total weight (56 kg) of the appliance suspended from it. if the air is to be ducted, the flue is in good condition, especially if it has been out of

use for a long period of time.

If the air is to be ducted, it will not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.

the installation will comply with laws and regulations regarding ducting waste gases.

for optimal efficiency, use smooth ducting for reduced noise and increased airflow. Flexible ducting should only be used as a last resort.

When you install the appliance, please make sure that

a suitable isolating switch is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. The switch

must be of an approved type installed in the fixed wiring and have a contact separation in all poles that provide full disconnection under overvoltage category III conditions.

it is not installed and connected to flues where other appliances are installed

and which run off energy supplies other than electricity (eg water heaters, boilers, gas cookers).

the power supply cable (type H05VV-F3x0.75 mm2) is connected to terminals marked with the letters L (power line) and N (neutral) mounted on the appliance and is secured

in position by a cable gland.

the power supply cable is connected to a suitable and easily accessible fixed power outlet or isolating switch.

the power outlet or isolating switch remains accessible after installation and the appliance can be disconnected from the electricity supply.

exhaust air is not discharged into a heating flue or wall cavity, unless the cavity is designed for that purpose.

If you install using the external ducting through a side wall, ensure the surface area of the external venting grill is no smaller than 150 cm2.

the glass and stainless steel components are handled with care. These are easily damaged if abraded or knocked by tools.

(1,2) -1-599489D izona vsisland install A2 NZGB.indd 21/7/09 2:51:59 PM

2 PRODUCT DIMENSIONS

Installation diagrams for illustration purposes only

 

F

C

 

 

E

 

F

A

 

 

G

 

D

B

C

Product dimensions (mm)

 

 

 

HI120

 

 

 

A

overall height of product (adjustable)

939

B

overall width of product

1198

C

overall depth of product

648

D

height to fixed flue section

62

E

width of flue

266

F

depth of flue

277

G

height from top of glass surface to top of fixed flue section

334

H

length of power supply cable

1450

3 CLEARANCE DIMENSIONS

A

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GAS

 

ELECTRIC

 

 

 

 

 

 

Clearances (mm)

 

 

 

 

HI120

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

minimum clearance from bottom of VentSurface to:

 

 

 

 

 

A trivets or pot support surface of gas cooktops

750

pot support surface of electric cooktops (including induction)

650

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*Note: to ensure that the VentSurface is able to perform at its best , we recommend that the clearance between the VentSurface and the cooking surface does not exceed 800 mm.

(2,1) -1-599489D izona vsisland install A2 NZGB.indd 21/7/09 2:51:59 PM

4 PARTS SUPPLIED

 

 

Support frame

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4 x 50 Screws (4)

 

 

 

 

 

 

 

 

 

 

 

 

 

Ceiling

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Extendable

Vertical flue

for vertical flue

4 x 16

3.5 x 9.5

Upper glass (1)

Aluminium

Plastic vent

mounting support

mounting support

and corresponding

mounting

flue cover (1)

brackets (4)

brackets (1)

Washers (4)

Screws (46)

wall anchors (4)

 

mesh filter (1)

duct (1)

frame (1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: ducting accessories, carbon filter and the Ductless Recirculating Kit are NOT supplied with your VentSurface but need to be purchased separately. They are available from your nearest Fisher & Paykel Authorised Service Agent, or www.fisherpaykel.com.

5 VENTILATION OPTIONS6 RATING PLATE LOCATION

Recirculation

(Requires Carbon Filter, to

External ducting be purchased separately as part of the Ductless

Recirculating Kit. Contact your nearest Fisher & Paykel Authorised Service Agent or www.fisherpaykel.com for instructions and details.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

External ducting

 

 

 

Recirculation

 

 

through a side wall

 

 

 

recirculates filtered air

 

 

or ceiling

back into the kitchen

TYPE

 

Cod.

SERIE

 

BATCH

V

Hz

W tot

W

 

W MAX

L

L

1

2 3

 

 

 

M2

M1

(2,2) -1-599489D izona vsisland install A2 NZGB.indd 21/7/09 2:51:59 PM

7 SECURE MOUNTING FRAME TO CEILING & MOUNT UPPER GLASS

A

1

6 mm holes

x 4

2

Ensure the washers

provided are used

B

8 ATTACH PLASTIC VENT DUCT & ASSEMBLE VERTICAL MOUNTING BRACKETS

A

B

 

1

 

1

 

x 4

 

2

(1,1) -2-599489D izona vsisland install A2 NZGB.indd 21/7/09 2:52:11 PM

9 ATTACH VERTICAL MOUNTING BRACKETS & SLIDE ON FLUE COVER

A

 

1

2

 

x 16

B

 

1

2

10 ATTACH MOUNTING BRACKETS TO MOUNTING FRAME & ATTACH FLUE COVER

A

 

2

x 8

 

1

Important!

VERY HEAVY: Ensure that the ceiling is able to withstand the total weight (56 kg) of the appliance suspended from it.

B

2

1

x 4

(2,1) -2-599489D izona vsisland install A2 NZGB.indd 21/7/09 2:52:11 PM

11 OPTIMISING THE VENTSURFACE BY SELECTING COOKTOP TYPE

To ensure best performance, the type of cooktop under the VentSurface needs to be selected after installing the appliance.

To select the type of cooktop

1 Make sure the VentSurface is onstand-by(plugged into a power outlet which is switched on but the fan is off).2 Press theandbuttons simultaneously. A single horizontal segment will appear in the display.

3Release and re-pressthe buttons simultaneously again to scroll through the types of cooktops:

Top segment – Gas

Middle segment – Induction

Bottom segment – Electric/Ceramic

Gas Induction Electric

Ceramic

4To store the type of cooktop last selected, press the orbutton.

12 SELECTING FILTER MODE

After installation, the VentSurface has to be set to operate on aluminium mesh filter mode (if the extracted air is ducted outside) or carbon filter mode (if the extracted air is recirculated indoors).

To change between filter modes

1 Make sure the VentSurface is onstand-by(plugged into a power outlet which is switched on but the fan is off).

2Press the button.

3a

The display will show the “-“symbol, indicating that the VentSurface is set toaluminium mesh filter mode (external ducting).

OR

 

 

 

3b

The display will show the “C” symbol, indicating that the VentSurface is set to carbon filter mode (internal recirculation).

4

Press the

 

button and hold down for at least five seconds to change to the filter mode you want. The filter mode last selected will be activated.

 

(2,2) -2-599489D izona vsisland install A2 NZGB.indd 21/7/09 2:52:11 PM

13 FINAL CHECKLIST

TO BE COMPLETED BY THE INSTALLER

Have you used the correct fixing screws?

Have you used the wall anchors provided?

Have you used the washers provided?

Have you made sure that all standard requirements for ducting/ recirculation and electrical connection are met?

Is the VentSurface set for the correct cooktop type and filter mode?

Is there a means of disconnection from the mains electricity

supply (disconnection switch or power outlet) accessible to the customer after installation?

Have you removed the protective blue film from the stainless steel surfaces?

Is the VentSurface earthed?

OPERATION:

Have you informed the customer about the cleaning alerts?

Have you demonstrated the basic operation to the customer?

Installer’s name:

Installer’s signature:

Installation company:

Date of installation:

LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER

www.fisherpaykel.co.nz www.fisherpaykel.com.au www.fisherpaykel.co.uk www.fisherpaykel.ie 599489D NZ AU GB IE 07.09