Size:
1.96 Mb
Download

USA

DD602 (Prefinished)

DD602I (Integrated)

 

 

 

 

Models DD602 DD602I

 

 

Part No. 599065/D

 

 

 

 

 

 

 

 

 

 

Table of Contents

 

 

 

 

 

 

 

Section

1

General Information

 

 

1.1

Preparation

 

 

1.2

Product Specifications & Cavity Dimensions

 

 

1.3

Options for Installing Multiple Products

 

 

1.4

Electrical, Plumbing & Drainage Information

 

 

1.5

Product Parts

 

 

1.6

Additional Product Parts for Integrated DishDrawer

 

Section

2

Foot Slide Retainer Information

 

 

2.1

Assembling the Foot Slide Retainer

 

 

2.2

Securing the Foot Slide Retainer

 

Section

3

Fitting the DishDrawer

 

 

3.1

Connecting the Services

 

 

3.2

Flexible Extrusion Attachment for 24” by 341/2” (610mm x 876mm) Cavity

 

 

3.3

Adjusting the Feet

 

 

3.4

Fitting the Endplate to the Chassis (Optional)

 

 

3.5

Securing the DishDrawer

 

Section

4

Prefinished Toe Kick Installation

 

 

4.1

Setting the Upper Toe Kick Height

 

 

4.2

Trimming the Lower Toe Kick

 

 

4.3

Trimming the Toe Kick Pins

 

 

4.4

Adjusting the Upper Toe Kick

 

 

 

 

 

 

Section

5

Information for Cabinet Maker for Integrated DishDrawer

 

 

5.1

Integrated Drawer Front & Toe Kick Dimensions

 

Section

6

Integrated Drawer Front Installation

 

 

6.1

Changing the Integrated Badge Enclosure

 

 

6.2

Disassembling the Integrated Badge

 

 

6.3

Assembling the Integrated Badge

 

 

6.4

Fitting the Badge, Handle & Mounting Panel to the Drawer Front

 

 

6.5

Fitting the Drawer Front Panels to the DishDrawer

 

Section

7

DishDrawer Toe Kick Information

 

 

7.1

Integrated Toe Kick Installation

 

 

 

 

 

 

Section

8

Final Checks

 

 

8.1

Installation Wet Test

 

 

8.2

Troubleshooting

Page DD_01

GENERAL INFORMATION

SECTION 1

 

 

STEP 1.1 PREPARATION

NOTE TO THE INSTALLER

νBe sure to leave these instructions with the Customer.

νEnsure this appliance is properly grounded.

NOTE TO THE CONSUMER

WARNING

ν

Keep these Installation Instructions with your Use & Care Manual for future

Before installing the

 

reference.

DishDrawer, remove the

IMPORTANT

house fuse or open the

ν

Read these Instructions completely and carefully.

circuit breaker.

ν

Observe all governing Codes and Ordinances.

 

WARNING

Ensure all water

ν

These Instructions are intended as a guide only.

νIt is the responsibility of the plumber and electrician to ensure that each installation connections are turned

complies with all Codes and Ordinances.

OFF.

νInstallation of this DishDrawer requires basic mechanical and electrical skills.

νThe installer is responsible for the DishDrawer installation.

Improper installation is not covered under the Express Warranty Form.

IMPORTANT

WARNING

ν

At the completion of the DishDrawer installation, the Installer must perform Final

 

Checks as per Section 8 of these Installation Instructions.

The DishDrawer MUST

ν

Ensure the DishDrawer enclosure is prepared for installation.

ν

Remove all packaging and materials supplied with the DishDrawer.

be installed to allow for

νIf you have any questions concerning the installation of this DishDrawer, contact: future removal from the

Fisher & Paykel Customer Care Centre

27 Hubble

enclosure if service is

required.

TOLL FREE 1-888-9-FNPUSA

Irvine

 

TOLL FREE 1-888-9-367 872

CA 92618

 

Fax (949) 790 8911

USA

 

WWW.FISHERPAYKEL.COM

 

 

STEP 1.2 PRODUCT SPECIFICATIONS & CAVITY DIMENSIONS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Electrical

 

110-120VAC

(Water pressure below 7 p.s.i.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 pin socket outlet

(50 kpa) may require the electronics

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Drying

Residual Heat

 

 

to be re-programmedby a Service

 

 

 

 

 

 

 

 

& Fan Assisted

 

 

Person at the time of installation)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Water Connection

Recommended Hot

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

140°F Max. (60°C)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Water Pressure

Maximum 139 p.s.i. (960 kpa)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Minimum 4.3 p.s.i. (30 kpa)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page DD_02

IMPORTANT

Where the DishDrawer is installed under a counter top, it is recommended that bare wood surrounding the DishDrawer is sealed with an oil based paint or polyurethane to prevent possible steam damage.

IMPORTANT

Ensure the cavity sides are plumb (vertical) as this will assist with leveling the DishDrawer.

IMPORTANT

Ensure the Services Hole is as close as possible to the rear lower corner of the cabinetry. The hole can be located on either side depending on the location of the services.

IMPORTANT

On corner installations, ensure that there is a gap of 2" (50mm) minimum between the adjacent cabinetry and sides of drawers.

Page DD_03

STEP 1.3 OPTIONS FOR INSTALLING MULTIPLE PRODUCTS

STEP 1.4 ELECTRICAL, PLUMBING & DRAINAGE INFORMATION

ELECTRICAL

Care should be exercised when the appliance is installed or removed, to reduce the likelihood of damage to the power supply cord.

If the power supply cord is damaged, it must be replaced by the Manufacturer, it’s Service Agent or a similarly qualified person, in order to avoid a hazard.

The power supply receptacle for the appliance should be installed in a cabinet or on a wall adjacent to the under counter space in which the appliance is to be installed.

The power supply receptacle should be positioned between 6" and 18" (150mm and 450mm) from the cabinet opening of the DishDrawer.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This appliance is equipped with a cord having an equipment-groundingconductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local Codes & Ordinances.

PLUMBING - WATER SUPPLY

a)The water connection is to be made to a hot water supply only. Ensure the water temperature is not greater than 140°F (60°C).

b)A readily accessible shut off valve must be installed in the supply pipe.

c)The water supply pressure is to be between 4.3 p.s.i. minimum and 139 p.s.i. maximum.

d)The inlet supply hose must be connected to the water supply using a 3/8" compression type water supply fitting.

e)Ensure sealing washer supplied with connection hose is fitted.

PLUMBING - DRAINAGE OPTIONS

Option 1

Option 2

Option 3

Note: Prefinished Model is shown. There is no variation in plumbing between Prefinished products and Integrated products. Options 1 and 2 are the most preferred options.

WARNING

Improper connection of the equipment-groundingconductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

WARNING

The Drain Hose Support must be at least 30" (750mm) above the floor to prevent siphoning of the water during the wash cycle.

It is recommended that the Drain Hose Support is secured in place using the screw tab.

Ensure that the drain hoses are fully extended.

Page DD_04

TOOLS NEEDED TO

STEP 1.5 PRODUCT PARTS

 

 

INSTALL DISHDRAWER

 

 

 

 

 

 

 

Wooden Chopping Board

 

1.

 

 

 

 

2.

Level

 

 

 

 

 

 

 

Safety Glasses

 

 

 

 

 

 

 

Utility Knife

 

 

 

 

 

 

 

Pencil

 

 

 

 

 

 

 

Drill & Drill Bits

 

 

 

 

 

 

4.

 

(3/32",9/16" &11/32") or

 

 

 

 

 

 

 

 

(2.5mm, 12mm, 14mm)

 

3.

 

 

 

 

 

Sandpaper

 

 

 

 

 

 

 

 

 

 

 

 

 

Tape Measure

 

 

 

 

 

 

 

Square

 

 

 

 

 

 

 

Ruler

 

 

 

 

 

 

 

Phillips Screwdriver

 

 

6.

 

 

 

 

Pliers

 

 

 

 

 

 

5.

 

 

 

 

 

Adjustable Wrenches (x2)

 

 

 

 

 

 

 

 

 

 

 

 

7/32" (6mm) Allen Key

 

 

 

 

7.

 

 

 

(Integrated Models)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Router (Integrated Models)

 

 

 

 

 

 

 

Jigsaw (Integrated Models)

8.

 

9.

 

10.

 

11.

 

 

 

 

 

 

 

12.

 

 

13.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16.

 

 

 

 

 

 

14.

 

 

18.

 

 

 

 

 

 

 

 

 

 

 

 

 

15.

 

17.

19.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

Retainer (1)

 

7.

Lower Toe Kick (1)

14.

Solderless Lug & Washer

 

 

 

(Channel Transverse)

 

 

2.

8.

Screws (11)

15.

Inlet Hose Washer (1)

 

 

Slide Runners

(2)

 

 

9.

Drain Hose Support (1)

16.

Transit Packer (1)

 

 

 

(Channel Longitudinals)

 

 

3.

10.

Wire Clips (2)

17.

Masonry Anchors (2)

 

 

Foot Slide Template (1)

 

 

11.

Drain Hose Joiner (1)

18.

Hose Clamp (1)

 

 

4.

Clip Pegs (2)

 

 

 

 

12.

Edge Protector (1)

19.

Endplates (2)

 

 

5.

Toe Kick Pins (2)

 

 

13.

Flexible Extrusion (3)

 

 

 

 

6.

Toe Kick Brace (1)

 

 

 

 

 

 

 

 

 

 

STEP 1.6 ADDITIONAL PRODUCT PARTS FOR INTEGRATED

 

 

 

DISHDRAWER

 

 

 

 

 

20.

Small Screws (14)

 

 

 

 

 

 

21.

Badge Kit (2)

 

 

 

 

 

 

 

22. Mounting Bracket Nuts (8)

 

 

 

 

 

 

23.

Door Screws (8)

 

 

 

 

 

 

24.

Seal (2)

 

 

20.

21.

 

 

 

 

 

 

 

23.

24.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

22.

 

 

Page DD_05

 

 

 

 

 

 

 

FOOT SLIDE RETAINER INFORMATION

STEP 2.1 ASSEMBLING THE FOOT SLIDE RETAINER

The Foot Slide Retainer is made up with one Retainer andtwo Slide Runners. The Toe Kick Brace is NOT used in the Foot Slide Retainer.

2.1.1

Bend the tabs at both ends of the Retainer so they fit the width of the cavity for the DishDrawer.

2.1.2

Assemble the Foot Slide Retainer by forming three sides of a square with the Retainer and Slide Runners as shown, ensuring that they fit together. Place in the cavity.

2.1.3

Using the front of the cavity, create a center point.

2.1.4

Place the Template in the cavity ensuring that the template is sitting flat and lines up with your center point.

SECTION 2

IMPORTANT

It is important that the Foot Slide Retainer is correctly installed. It guides the feet back and holds the rear of the DishDrawer down to prevent it rocking forward when the drawers are opened. It also aligns the product to the cavity front.

WARNING

Be careful of sharp edges.

IMPORTANT

If there is a drop down in the cavity, you may have to build the cavity up level with the finished floor.

Page DD_06

IMPORTANT

For Integrated product with door thickness other than 3/4” (18mm), the Foot Slide position must be adjusted forward or back to allow for this difference.

IMPORTANT

Check for any protrusions that may interfere with the DishDrawer sliding back into the cavity and allow for these.

IMPORTANT

The Foot Slide Retainer must be adequately secured to prevent movement.

Page DD_07

2.1.5

Position the Foot Slide Retainer within the cutout areas of the Template.

2.1.6

The Template should be placed in the cavity until the wings just touch the existing cabinetry. This ensures the front of the DishDrawer will be flush with the existing cabinetry.

Correct

Incorrect

STEP 2.2 SECURING THE FOOT SLIDE RETAINER

There are two options available for securing the Foot Slide Retainer. Either option is adequate for securing the DishDrawer. Using both options together is optimum.

2.2.1

The first and preferred option is to screw the Retainer to the floor. The tabs can be broken off at the perforations, if they are not used.

2.2.2

The second option is to screw the Retainer to the cabinet sides.

2.3.3

Masonry Anchors are supplied with the accessories to replace the long screws if attaching the Foot Slide Retainer to concrete flooring.

Masonry Anchors should not be used if there is any chance of damaging underfloor heating.

FITTING THE DISHDRAWER

STEP 3.1 CONNECTING THE SERVICES

3.1.1

Feed the Power Cord, Inlet Hose and Drain Hoses through the Services Hole. Position the DishDrawer in front of the opening.

3.1.2

Connect the Inlet Hose to the HOT WATER SUPPLY. Ensure sealing washer supplied with the accessories is fitted. Hose coupling must be tightened a further half turn after seal contact.

3.1.3

If required, the Drain Hose may be trimmed to a suitable length.

3.1.4

If an air break option is not chosen, then the Drain Hose Support must be used and positioned at least 30" (750mm) above the floor to prevent siphoning of the water during the wash cycle. (See Step 1.4 - Electrical, Plumbing & Drainage Information.)

3.1.5

When using a standpipe option, hoses should not extend further than 2” (50mm) down the standpipe in order to prevent siphoning.

3.1.6

If required, trim the Drain Hose Joiner to the size which matches the waste tee or air break to be used. There are ribs provided to guide cutting.

When using the Drain Hose Joiner, the hoses should be pushed in firmly, 5 clicks.

3.1.7

Attach the Drain Hose Joiner to the waste tee(see Step 1.4). Ensure a snug fit, using the hose clamp supplied.

The supplied Wire Clips should be installed between the two positioning ribs on the Drain Hose Joiner.

Remember to slip the Wire Clips over the

Drain Hoses before connecting to the

Drain Hose Joiner.

SECTION 3

WARNING

Ensure the edges of the Services Hole are smooth or covered. (See Step 1.2 - Product Specifications & Cavity Dimensions.) If the Services Hole is through a metal partition, the hole must be protected with the Edge Protector provided.

WARNING

DO NOT adjust the length of the Inlet Hose.

TIP

Turn the water valve ON to check for any leaks, before pushing the DishDrawer back into its cavity.

WARNING

Attach the Drain Hose Support to the cabinet joinery to prevent siphoning and keep the drain hoses from kinking.

Page DD_08

WARNING

The Product must not be plugged in at this stage.

WARNING

If permanently connecting, ensure power is isolated.

TIP

Wiring, Plumbing and Services should be completed before attaching the flexible extrusion.

Page DD_09

3.1.8

Ensure there is a power outlet in reach of the supplied flex. If there is not a suitable outlet available then have one installed by a qualified electrician.

DO NOT modify the power plug supplied with the DishDrawer or use an extension cord, adaptor plug or multiple outlet box.

3.1.9

Alternatively, the DishDrawer may be permanently connected to flexible conduit.

Remove the flex and cable clamp. Fit suitable cable clamp for the conduit and terminate the wiring as shown.

Use the solderless lug and washer supplied with the product parts to terminate the ground wire.

STEP 3.2 FLEXIBLE EXTRUSION ATTACHMENT FOR 24” BY 341/2” (610mm x 876mm) CAVITY

3.2.1

Flexible Extrusions are supplied to enable the installer to help fill any excess space between the sides and top of the DishDrawer and the cavity. The three lengths of Flexible Extrusion (supplied) should be attached before pushing the DishDrawer into the cavity for final installation. The Extrusions are designed to fit a 24” width by 341/2” high cavity (610mm x 876mm).

3.2.2

Open the drawers, exposing the chassis trim.

Cabinet

Cabinet

DishDrawer

DishDrawer

3.2.3

Remove backing from adhesive tape on Flexible Extrusion. The larger of the Extrusions is used to fill the gap at the top of the product.

3.2.4

Apply as per drawings, ensuring the curved edge of the Flexible Extrusion fits around the corner of the chassis trim.

3.2.5

When checking final fit, ensure the DishDrawer is centered and there are even tolerances between the DishDrawer and cavity.

STEP 3.3 ADJUSTING THE FEET

3.3.1

Measure front of product to align to cabinetry as required.

Ensure a minimum of 1/8" (2.5mm) clearance to the underside of the counter.

The height difference between the front and the back of the DishDrawer must be no more than 1/8" (2.5mm).

3.3.2

To adjust the feet, loosen the locknuts and turn the feet. If the product needs to be adjusted to its lowest setting, the plastic surround will need to be removed by unscrewing and lifting it up and slipping it off the foot.

3.3.3

Tighten the locknuts on the rear feet while ensuring the moulded section of the feet line up parallel to the sides of the product.

3.3.4

Lift the back of the DishDrawer and insert the back feet into the Slide Runners. Slide the DishDrawer partially back, leaving enough room to adjust the front feet.

3.3.5

Further adjustment may be made if necessary. Lock the front feet while ensuring the moulded section of the feet line up parallel to the sides of the product.

STEP 3.4 FITTING THE ENDPLATE TO THE CHASSIS (OPTIONAL)

IMPORTANT

The DishDrawer must be levelled so that each corner is at least within 1/8” (3mm) of level.

WARNING

The DishDrawer should not support any part of the kitchen cabinets.

IMPORTANT

Make sure the Inlet and Drain Hoses are not restricted or damaged.

TIP

Each turn of the foot adjusts by 3/64(1.25mm).

TIP

For ease when sliding the feet back, place a little soap on the Slide Runners.

3.4.1

If the customer sees a need, Endplates may be used to obtain a flush appearance to the side of Toe Kick area of the product.

The Endplate is fitted by peeling off the adhesive backing and adhering to the side of the chassis, lining up the front of the Endplate with the Upper Toe Kick.

Page DD_10

STEP 3.5 SECURING THE DISHDRAWER

3.5.1

Partially lift the top mounting tabs by inserting a flat screwdriver into the Vee shaped slot. Complete the folding process by bending about the rows of oval slots so that the tab is approximately level and parallel with the underside of the bench.

3.5.2

Lift the DishDrawer and insert the front feet into the Slide Runners. While the machine is still outside the cavity, fold out the tabs on top of the DishDrawer.

Push the DishDrawer back until the back feet slide into the rear grooves of the Retainer. Ensure the DishDrawer is as far back as it will go.

3.5.3

Insert the Clip Pegs into the Slide Runners in front of the front feet. Push the Clip Peg back until it locates in the two holes on either side of the Slide Runner. This locks the DishDrawer in place as well as providing the mounting clips for the Lower Toe Kick.

3.5.4

Screw in tabs to underside of bench. Use the two Phillips No. 8 x 5/8” screws supplied to secure the DishDrawer to the bench. This provides optimal product rigidity within the cavity.

Page DD_11

PREFINISHED TOE KICK INSTALLATION

STEP 4.1 SETTING THE UPPER TOE KICK HEIGHT

4.1.1

Remove the Upper Toe Kick by opening the bottom drawer, then holding the Toe Kick at the base, pull outwards to unclip and rotate up.

4.1.2

Ensure the screws are at the highest position, so the Upper Toe Kick will be situated on the DishDrawer as high as it can go. This allows for later adjustment to suit the Lower Toe Kick.

4.1.3

Replace the Upper Toe Kick by feeding the top tabs up through the slots in the tub, then rotate the Toe Kick to clip back and lock home.

STEP 4.2 TRIMMING THE LOWER TOE KICK

4.2.1

The Lower Toe Kick sits flush with the floor.

Turn the Lower Toe Kick upside down and position at a 90° angle against the already fitted Upper Toe Kick.

UP

SECTION 4

IMPORTANT

Ensure that the Transit Packer located beneath the upper Toe Kick has been removed.

Page DD_12

IMPORTANT

Before cutting the Lower Toe Kick, ensure the Toe Kick is positioned on a wooden chopping board to avoid damage to surrounding area.

IMPORTANT

Ensure the Toe Kick Pins are positioned on a wooden chopping board to avoid damage to surrounding area.

4.2.2

To establish which groove to trim along, measure the Toe Kick against both sides of the product, allowing a minimum gap of 3/32” (2.5mm) between the Upper and Lower Toe Kicks.

Neatly cut through the vertical ribs of the Toe Kick and trim along the full length of the groove.

4.2.3

Bend the cut edges apart slightly and carefully cut through from the front.

4.2.4

Sand the edges to remove any rough patches.

STEP 4.3 TRIMMING THE TOE KICK PINS

4.3.1

Mark the Toe Kick Pins against the trimmed Lower Toe Kick.

NOTE: DO NOT insert the Pins into the Kick before cutting to length.

4.3.2

Place the Toe Kick Pin onto a wooden chopping board and trim the Pin by cutting down the corresponding groove to the trimmed Lower Toe Kick. Cut the outer edges of the Toe Kick Pins from the inside to the outside.

Page DD_13

4.3.3

If the height of the Lower Toe Kick is greater than 11/4" (32mm) , insert the Toe Kick Brace in between the two lowest ribs of the Lower Toe Kick.

4.3.4

Insert the Toe Kick Pins into the Lower Toe Kick. These will hold the Brace in place.

Orientate the Lower Toe Kick so that the arrow points upwards.

Toe Kick

Brace

STEP 4.4 ADJUSTING THE UPPER TOE KICK

4.4.1

Snap the Lower Toe Kick into the Clip Pegs in the Slide Retainer.

Measure the gap between the Lower and Upper Toe Kick at the left and right sides.

4.4.2

Remove the Upper Toe Kick and using the increments, adjust to allow a 3/32" (2.5mm) gap between the two Toe Kicks.

Replace the Upper Toe Kick and check.

02

808

 

91

9

 

81

78

 

71

7

 

3061

6

 

51

65

 

2941

4

Upper Toe Kick

31

53

 

21

2

 

2811

1

 

01

480

 

279

9

 

8

38

 

7

7

 

266

6

Lower Toe Kick

 

2 5

 

5

254

4

Page DD_14

SECTION 5

IIMPORTANT

N

Recommended Drawer

Front thickness for

T

Integrated products is

5/8" to3/4" (16mm to

 

18mm).

ERecommended Toe Kick

Gthickness is 3/8" (9mm).

R

IMPORTANT

A

Drawer Front material

Tmust be suitable for damp conditions or

adequately sealed to E withstand moisture.

DAdditional protection can be provided by using a “Moisture Resistant Board”.

P

RIMPORTANT

O

Allow for any

 

D

obstructions at the top of

the cavity when allowing

 

for space between the

Ucountertop and DishDrawer.

C

T

IMPORTANT

A 1/4” (6mm) gap must be

Oprovided between top and bottom Drawer Front

Nin the position shown.

L

Y

Page DD_15

INFORMATION FOR CABINET MAKER FOR INTEGRATED DISHDRAWER

STEP 5.1 INTEGRATED DRAWER FRONT & TOE KICK DIMENSIONS

5.1.1

Use the following diagrams to work out the dimensions for the Integrated Panels for Drawer Fronts and Toe Kicks..

IMPORTANT

Check top and bottom measurements of cavity and use the smaller dimension to ensure that the drawer fronts and toe kicks will fit.

Drawer Front Air Flow Chamfer

Chamfer the back of the Drawer Front Panel at the bottom as shown, to enhance airflow.

Page DD_16

I

N

T

E

G R A T E D

P

R

O D U C T

O N L Y

IMPORTANT

I

All marking out should

Nbe done on the back surface of the Drawer

TFront.

E

G

R

A

TIMPORTANT

E

When mounting the

handle, ensure fastenings

 

D

do not protrude beyond

the back surface of the

 

Drawer Front.

P

R

O

DIMPORTANT

Accuracy is essential U when cutting the Badge

Mounting Hole to ensure

Ca neat fit to hold the badge.

T

O

N

L

Y

Page DD_17

5.1.2

Control Badge Position

Badge can be located anywhere within the Mounting Zone shown. Handle position will need to be taken into account.

5.1.3

Badge Cutout Dimensions

Cut out Badge Mounting Hole in the chosen position (see Control Badge Mounting Zone on diagram above). A Control Badge Template (Part No. 526253) is available on request from Fisher & Paykel or alternatively a Template can be found on the Mounting Bracket enclosed with the product.

The Badge Mounting Hole is an ellipse shape.

5.1.4

Drawer Front Mounting Bracket Nut Holes

Using a 11/32” (8.5mm) diameter drill bit, drill out the four screw holes in each door panel to a depth of9/16” (14mm). Remove burrs.

At least 5/8” (16mm) of Drawer Front material is required for the Drawer Mounting Nuts (M6 screw in nut - Type E).

* These dimensions are important to ensure the1/4” (6mm) airflow gap is correctly located.

5.1.5

Toe Kick Mounting Pilot Holes

Using a 3/32” (2.5mm) diameter drill bit, drill out the six screw holes in the Upper Toe Kick to a depth of1/4”(6mm).

Lower Toe Kick Mounting Pilot Holes are drilled at the time of installation.

WARNING

Use of a depth gauge is recommended when drilling out holes for Drawer Front Mounting Panel.

CAUTION

Ensure the drill does not damage the face of the Drawer Front.

Page DD_18

I

N

T

E

G R A T E D

P

R

O D U C T

O N L Y

 

 

SECTION 6

 

I

 

IMPORTANT

 

 

 

N

To avoid electric shocks

 

T

and damage to electronic

 

components, the

 

 

integrated badge should

Ebe disconnected from the DishDrawer when

Gchanging the badge enclosure.

R

A

T

E

D

P

R

O

D

U

C

TBadge Button

O

 

N

 

Connection Runner

 

L

 

Y

 

 

Page DD_19

INTEGRATED DRAWER FRONT INSTALLATION

STEP 6.1 CHANGING THE INTEGRATED BADGE ENCLOSURE

There are several different colored Integrated badges to choose from. They include black, chrome, satin & brass. Two color options are provided with your machine, other options are available from your local Dealer.

There are five parts to the

 

5.

 

Integrated Badge Assembly.

 

3.

 

They are as follows:

 

4.

1.

Integrated Badge

 

 

 

2.

Badge Buttons

 

 

 

3.

Light Pipe

 

 

 

4.

Electronics Board

1.

2.

 

5.

Badge Cover

6.

6.

Wires

 

 

STEP 6.2 DISASSEMBLING THE INTEGRATED BADGE

6.2.1

Remove Badge Cover from the Integrated Badge. At the back of the Integrated Badge, slide the Badge Cover away from the wire terminals.

6.2.2

Remove Electronics Board. Gently hold the wires to remove the Electronics Board. Care should be taken not to handle the front or back of the Electronics Board or touch inside the wire terminals.

6.2.3

Remove the Light Pipe. Gently tap the Integrated Badge upside down on a hard surface until the light pipe comes away or insert a pen or pencil into the front side of the Integrated Badge to either one of the two small holes.

6.2.4

Once you have removed the Electronics Board, Badge Cover and Light Pipe, you can change the color of the Integrated Badge.

STEP 6.3 ASSEMBLING THE INTEGRATED BADGE

6.3.1

Insert the Badge Button into the back of the Integrated Badge. Do not break any of the buttons away from the Connection Runner.

6.3.2

Insert the Light Pipe into the Integrated Badge. Insert the Light Pipe with the circular ends into the small holes.

6.3.3

Insert the Electronics Board with care, behind the Badge Button. When installing the Electronics Board, handle only the wires and do not touch the face or back of the Electronics Board or inside the wire terminals.

6.3.4

Slide the Badge Cover into the slot on top of the Integrated Badge.

STEP 6.4 FITTING THE BADGE, HANDLE & MOUNTING

WARNING

PANEL TO THE DRAWER FRONT

Care should be taken in

 

6.4.1

the following steps.

 

Remove Drawer Front Mounting Panel by

 

withdrawing pins from sides of drawers.

 

6.4.2

CAUTION

 

Slide Mounting Panel off in a downwards

Take care not to damage

and outwards motion.

front surface of panel.

 

6.4.3

Ensure all cuts are

Using an Allen Key, screw in Mounting

straight and care is taken

Bracket Nuts. Remove Burrs. Screw in

to avoid damage to the

flush with back surface.

Drawer Front.

 

6.4.4

Fit the Drawer Mounting Panels using the screws supplied.

CAUTION

Overtightening will damage the Drawer Front.

6.4.5

Feed wires through to the back and press badge into hole, if needed adhere badge to Drawer Front with a glue or silicon sealant.

6.4.6

Fit the customer supplied handle.

Page DD_20

I

N

T

E

G R A T E D

P

R

O D U C T

O N L Y

TIP

I

Use a small amount of

Nliquid soap along the lip of the seal to assist the

TDrawer Front to slide on easily against the seal.

E

WARNING

G

Ensure the product is not

Rplugged in.

A

TWARNING

EThe Electronics Board is an electrostatic sensitive

Ddevice. Ensure you are adequately grounded when connecting or disconnecting the badge by wearing a grounding

Pstrap or by grounding yourself to the

RDishDrawer.

O

D

U View of Slide Hooks

CORRECT

C

T

O

 

N

 

L

 

Y

INCORRECT

 

STEP 6.5 FITTING THE DRAWER FRONT PANELS TO THE DISHDRAWER

6.5.1

Fit seal to Drawer.

6.5.2

Plug the badge grounding wire onto the Drawer Front Panel.

Connect badge wires to the integrated badge port on the Electronics Board.

6.5.3

Fit the Drawer Front by sliding in an inwards and upwards motion. The rubber seal between the Drawer and Drawer Front must be kept in place.

6.5.4

Ensure the slide hooks (on slide) are as far forward as possible, (as shown). Insert pins to lock in place, ensuring that the rib on the pin is vertical.

6.5.5

Check fit and air flow gap and adjust if necessary.

Page DD_21

DISHDRAWER TOE KICK INFORMATION

SECTION 7

 

 

STEP 7.1 INTEGRATED TOE KICK INSTALLATION

I

Upper Toe Kick

7.1.1

N

Remove Plastic Toe Kick from product.

 

Unscrew metal back panel.

T

 

7.1.2

E

Place customer supplied Upper Toe Kick

 

face down on soft surface. Locate metal

G

back panel on rear of Toe Kick (ensure

the bottom of Toe Kick and panel are

 

flush and centered).

R

 

7.1.3

A

Using screws provided, fix metal panel

 

onto Toe Kick. Install Upper Toe Kick

T

onto product.

Lower Toe Kick

E

7.1.4

D

Place customer supplied Toe Kick face

down on a soft surface and mark a

Toe Kick

vertical center line.

 

Measure out from center

 

929/32 (251.5mm) and 105/8 (269.5mm) in

P

both directions and mark Toe Kick pin

hole center lines.

R

7.1.5

O

Trim the Toe Kick pin to length, at the

nearest groove. The correct length is

 

such that when the bottom of the pin is

D

3/64” (1mm) above the bottom of the toe

kick, the top is within +/- 1/8” (3mm) of the

U

Toe Kick top.

7.1.6

C

Cut Toe Kick Pin. Locate Toe Kick Pin

 

screw holes over the vertical lines. Line

T

up the cut base of the Toe Kick Pin

3/64” (1mm) above the bottom of the Toe

 

Kick then mark out the screw holes.

7.1.7

O

Drill pilot holes to a depth of 1/4" (6mm).

 

Fix Toe Kick Pins to Toe Kick with screws

N

provided. Install Toe Kick to product.

7.1.8

L

Y

Adjust the Upper Toe Kick as per Step 4.4

to achieve gap.

 

Page DD_22

SECTION 8

Page DD_23

FINAL CHECKS

STEP 8.1 INSTALLATION WET TEST

1. Ensure product is level, securely fastened to the floor and opens and closes freely.

2.

Ensure inlet hose to faucet connection is tightened to specification.

 

 

 

3.

Ensure any knockouts or plugs in drain connection have been drilled out

 

 

and drain connection made to specification.

 

4.

Plug in and turn ON the power and water supply. The DishDrawer should

 

 

5.

"beep" and light up.

 

 

Open the drawers of the DishDrawer and check operation of Secondary

 

 

6.

Control Panel and check sprayarm(s) are in place and free to rotate.

 

 

Select Rinse program on the Secondary Control Panel and close the

 

7.

drawers.

 

 

Start the Program by pressing the Start/Pause button.

 

 

 

8.

After the program has finished, check underneath the DishDrawer for

 

 

water leakage. Ensure machine has run and drained correctly.

 

9.

Check water supply and drainage connection for leakage.

 

 

 

10.

Repeat for each Drawer.

 

 

 

STEP 8.2 TROUBLESHOOTING

1.

Water underneath DishDrawer; check the hose connections and hose for

 

 

2.

leaks.

 

 

Water around water supply and drainage connections - check connections,

 

3.

existing plumbing and hoses for leaks.

 

 

Excessive water remaining above the filter plate, after the rinse cycle;

 

 

check for kinked drain hoses or blocked waste connection.

 

4.

No water supply; check water is on and there is water pressure.

 

 

5.

If a fault occurs, consult the Problem Solver Section of the Use &

 

 

Care Manual.

 

6.

 

 

If unable to resolve, contact Customer Care Center.

 

 

 

 

Ensure Power is connected and is switched ON.

Ensure the water supply is connected and ON.

LEAVE ALL LITERATURE WITH THE CUSTOMER.