Fisher & Paykel CG733 User Manual

Size:
2.64 Mb
Download

Gas-on-glasscooktop

Installation instructions

CG733 model

and User guide

 

 

CG733

 

SG HK

Contents

 

 

 

 

1

EN

Safety and warnings

2

 

 

 

 

Installation instructions

6

 

 

Introduction

20

 

 

Using your cooktop

21

 

 

Care and cleaning

26

 

 

Troubleshooting

30

 

 

Warranty and service

31

 

 

Important!

SAVE THESE INSTRUCTIONS

The models shown in this manual may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our local website listed on the back cover or contact your local Fisher & Paykel dealer.

EN 2 Safety and warnings

WARNING!

Cut Hazard

Take care - some panel edges are sharp.

Failure to use caution could result in injury or cuts.

WARNING!

Electrical Shock Hazard

Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains power supply.

Connection to a good earth wiring system is essential and mandatory.

Failure to follow this advice may result in death or electrical shock.

Important safety precautions

Installation

Read these instructions carefully before installing or using this product.

Please make this information available to the person responsible for installing the product as it could reduce your installation costs.

This appliance must be installed in accordance with these installation instructions, local gas fitting regulations, municipal building codes, electrical wiring regulations, and any other relevant statutory regulations.

This appliance shall only be serviced by authorised personnel.

Always disconnect the cooktop from mains power supply before carrying out any maintenance operations or repairs.

Particular attention shall be given to the relevant requirements regarding ventilation. In the room where the cooktop is installed, there must be enough air to allow the gas to burn correctly, according to the current local regulations.

Do not modify this appliance.

When this appliance is installed, it shall not be used as a space heater.

No combustible materials or products should be placed on this appliance at any time. Do not spray aerosols in the vicinity of this appliance while it is still in operation.

Safety and warnings 3 EN

This appliance should not be sealed into the bench with silicone or glue. Doing so will make future servicing difficult. Fisher & Paykel will not be liable for costs associated with releasing such a product, nor for repairing damage that may be incurred in doing this.

Packing elements (eg plastic bags, polystrene foam, staples, packing straps etc) and tools should not be left around during and after installation, especially if they are within easy reach of children, as these may cause serious injuries.

EN 4 Safety and warnings

WARNING!

Hot Surface Hazard

This appliance becomes hot during use.

Do not touch the cooktop components, burners, trivets/pan supports or the base when hot.

Before cleaning, turn the burners off and make sure the whole cooktop is cool.

Failure to follow this advice may result in serious injury.

WARNING!

Explosion Hazard

Do not store flammable materials such as gasoline near the cooktop. Do not spray aerosols near the cooktop during use.

Failure to follow this advice may result in death or serious injury.

WARNING!

Electrical Shock Hazard

Do not cook on a broken or cracked cooktop. If the cooktop surface should break or crack, turn off the gas supply and switch the appliance off

immediately at the mains power supply (wall switch) and contact a qualified technician.

Switch off the cooktop at the wall before carrying out cleaning or maintenance.

Failure to follow this advice may result in death or electrical shock.

WARNING!

Fire Hazard

Never leave the appliance unattended when in use. Boilover causes smoking and greasy spillovers that may ignite.

Never use your appliance for warming or heating the room.

Failure to follow this advice may result in serious injury.

Safety and warnings 5 EN

Important safety precautions

Operation

Keep children away from the cooktop when it is in use.

Household appliances are not intended to be played with by children.

Children, or persons with a disability which limits their ability to use the appliance, should have a responsible person to instruct them in its use. The instructor should be satisfied that they can use the appliance without danger to themselves or their surroundings.

If the power supply cable is damaged, it must only be replaced by an authorised person. Ensure that the electrical connection plug is accessible after installation.

This appliance should be connected to a circuit that incorporates an isolating switch providing full disconnection from the power supply.

Do not use an asbestos mat or decorative covers between the flame and the saucepan as this may cause serious damage to your cooktop.

Do not place aluminium foil or plastic dishes on the cooktop burners.

Do not let large saucepans, frying pans or woks push any other pans aside. This could make them unstable or deflect heat onto your benchtop and damage the surface.

Do not use a steam cleaner for cleaning this cooktop.

Saucepan handles may be hot to touch. Ensure saucepan handles do not overhang other gas burners that are on. Keep handles out of reach of children.

Keep children away from the cooktop when it is in use.

Household appliances are not intended to be played with by children. Do not stand on this appliance.

Do not place or drop heavy objects on this appliance. After use, ensure that the knobs are in the OFF position. This appliance shall not be used as a space heater.

The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed. Ensure the kitchen is well ventilated. Keep natural ventilation holes open or install a mechanical ventilation device (mechanical extractor hood). Prolonged intensive use of the appliance may call for additional ventilation, for example opening of a window, or more effective ventilation, for example increasing the level of mechanical ventilation where present.

After having unpacked the appliance, check to ensure that it is not damaged.

In case of doubt, do not use it and consult your supplier or a professionally qualified technician. Packing elements (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.) should not be left around within easy reach of children, as these may cause serious injuries.

EN 6 Installation instructions

Cooktop and cutout dimensions

Electrical connection is made at the left rear

A

C B

E

D

H

G

F

Cooktop and cutout dimensions (mm)

 

 

CG733

A

overall width of cooktop

730

B

overall depth of cooktop

430

C

height of chassis (below top of bench)

53

D

width of chassis

700

E

depth of chassis

400

F

overall width of cutout

705

G

overall depth of cutout

405

H

corner radius of cutout

max. 120

 

 

 

 

 

 

Installation instructions

Clearances

A

E

B

C

D

Clearances (mm)

minimum clearance from rear edge of cutout to:

Anearest combustible surface

minimum clearance from glass surface to: rangehood

Bany other overhead exhaust fan

downward-facingcombustible surface (overhead cabinetry)downwards-facingtiled or fire resistant surface

minimum clearance from side edges of cutout to:

Cnearest combustible surface

minimum clearance below top of benchtop to:

Dthermal protection barrier

minimum clearance from benchtop to:

Eoverhead cabinet not directly above the cooktop

7 EN

CG733

60

650

800

650

500

213

83

450

EN 8 Installation instructions

The appliance may be installed in a suitable room in accordance with the current laws in force. The appliance is designed and approved for domestic use only and should not be installed in a commercial, semi-commercialor communal environment.

Installing the appliance in any of the above environments will void the warranty and could affect any third-partyor public liability insurances you may have.

The appliance must be installed in compliance with regulations in force.

Installation technicians must comply with current laws in force concerning ventilation and the evacuation of exhaust gases.

Always disconnect the appliance from the electrical supply before carrying out any maintenance operations or repairs.

The walls of the units around the appliance must not be higher than the benchtop and must be capable of resisting temperatures of 105oC above room temperature.

Do not install the appliance near flammable materials (eg curtains).

You must install a thermal protection barrier between the base of the appliance and the built-inunit or an oven. See Fig. 1 below.

If the appliance is installed over a built-inoven, the oven should be fitted with a cooling fan and the two appliances should be connected to the gas and electricity supply with independent connections.

The thermal protection barrier must be:

removable heat-resistant

made from low thermal conductivity material at least 30 mm below the base of the cooktop

Clearance Thermal

protection barrier

Space for connections

30 mm

Door

Fig. 1 Location of thermal protection barrier

Fig. 2a Ventilation with an extractor hood
Electric fan to extract steam
Air vent
Fig. 2b Ventilation with an electric fan

 

 

 

Installation instructions

 

 

9

EN

 

 

 

 

Ventilation requirements

Providing adequate ventilation

The installer must refer to the current local regulations. The room accommodating the gas cooktop must have adequate natural draught to allow combustion of the gas.

The flow of air must come directly from one or more air vents made in the outside walls with a free area of at least 100 cm2 (or refer to applicable local regulations).

The vents must be positioned close to the floor, preferably on the opposite side to the gas burners of your cooktop (as shown in Figs. 2a and 2b). The vents must be designed in such a way that they cannot be obstructed either from the inside or the outside.

When it is not possible to provide the necessary vents, the draught may be supplied from an adjacent room, ventilated in the required manner, provided it is not a bedroom or an area at risk. In this event, the kitchen door must be opened to allow the draught to enter the room.

Extracting cooking and gas fumes

Important!

This appliance is not connected to a device extracting the products of gas combustion. Such a device must be installed and connected in accordance with the installation rules in force. Take special care to provide adequate room ventilation as well.

To eliminate cooking and gas fumes, extractor hoods ducted directly to the outside must be installed (Fig. 2a). If this is not possible, an electric fan installed in an external wall or window may be used; the fan should have a capacity to circulate air at an hourly rate of 3 to 5 times the total volume of the kitchen (Fig. 2b). The fan can only be installed if the kitchen has suitable vents to allow air to enter, as described under ‘Providing adequate ventilation’ above.

Extractor

 

hood to

mm

extract steam

 

H min 650

Air vent

 

EN 10 Installation instructions

Fastening the cooktop to the bench

1Turn the cooktop upside down and place it on a soft surface.

2Spread the seal around the edges, with the adhesive side facing down.

3Mount the supplied front and rear clamps (R) and screws (S) onto the cooktop, as shown (without tightening the screws).

4Place the cooktop into the cutout, then tighten the screws to clamp the cooktop securely to the bench.

5Using a sharp cutter or trimmer knife, trim the excess sealing material around the edge of the cooktop. Take care not to damage the benchtop.

Note: if your bench is thicker than 40 mm, recess the underside to between 20 and 40 mm.

R S

R

S

S R

S R

Seal

Adhesive side

Fig. 3 Preparing the cooktop before installation

40 mm

20 mm

R S

A

30 mm min

Fig. 4 Fastening the cooktop to the bench

Installation instructions 11 EN

Gas installation requirements

Important !

Before installation, make sure that the local distribution conditions (gas type and pressure) and the adjustment of this appliance are compatible. The appliance adjustment conditions are given on the plate or the label.

This appliance must be installed and serviced only by a suitably qualified, registered installer with technical knowledge of both gas installation and electricity. The installation or service must comply with the current editions of the applicable standards, regulations, and codes of practice governing gas and electrical installations.

Failure to install the appliance correctly could void any manufacturer’s warranty.

This appliance is supplied for use on NATURAL GAS or LPG or TOWN GAS (check the gas regulation label attached on the appliance).

Appliances supplied for use with NATURAL GAS: these are adjusted for this gas only and cannot be used with any other gas (LPG or TOWN GAS) without modification. The appliances may be converted to LPG or TOWN GAS using the conversion kit.*

Appliances supplied for use on LPG: they are adjusted for this gas only and cannot be used on any other gas (NATURAL GAS or TOWN GAS) without modification. The appliances may be converted to NATURAL GAS or TOWN GAS using the conversion kit.*

Appliances supplied for use with TOWN GAS: these are adjusted for this gas only and cannot be used with any other gas (NATURAL GAS or LPG) without modification. The appliances may be converted to NATURAL GAS or LPG using the conversion kit.*

*If the NATURAL GAS/LPG/TOWN GAS conversion kit is not supplied with the appliance, this kit can be purchased by contacting Fisher & Paykel. Please see your ‘Warranty & Service’ booklet for further details.

EN 12 Installation instructions

Gas Connection

Note: Connection to the gas supply may be made using either a rubber hose (where permitted) or by using a flexible hose or rigid pipe.

Gas connection with a rubber hose

Important !

A rubber hose connection shall only be made if permitted by the applicable local regulations.

The gas connection fitting (Fig. 5a) is made up of: the appliance inlet pipe;

the floating nut; the brass elbow; the washers;

the appropriate hose holder (for NATURAL GAS/TOWN GAS or LPG).

Gas connection with rubber hose holder

Note: if not already fitted on the inlet pipe, the hose holder

is supplied with the product in a separate kit; if not supplied with the appliance it can be purchased by contacting Customer Care.

(Important: to be used ONLY IF PERMITTED by the local applicable regulations)

Turning the gas

½” G cylindrical

Washer

 

(ISO 228-1)male

Floating nut

 

connection fitting

 

 

 

 

 

 

Brass elbow

 

 

 

 

 

Appliance

 

 

 

inlet

 

Washer

½” G cylindrical

pipe

 

(ISO 228-1)male

 

 

 

½” G cylindrical

 

½” G cylindrical

 

(ISO 228-1)female

 

(ISO 228-1)female

Hose holder for NATURAL GAS or TOWN GAS

Hose holder for NATURAL GASor TOWN GAS

Washer

 

Hose clamp

 

 

(not supplied)

Hose adaptor

 

Rubber hose (not supplied)

 

for NATURAL GAS

for LPG

 

 

or TOWN GAS connection

 

 

Rubber hose (not supplied)

Hose clamp

(internal diameter 13 mm)

 

for LPG connection

Fig. 5a Gas connection

(not supplied)

(internal diameter 8 mm)

with a rubber hose

 

Installation instructions 13 EN

Connecting the appliance to NATURAL or TOWN GAS

1If not already fitted, fit the NATURAL/TOWN GAS hose holder on the inlet pipe, making sure that you place the sealing washer between them (as shown in Fig. 5a).

2Connect the appliance to the gas supply using a suitable rubber hose (internal diameter 13 mm). The hose must comply with the applicable local regulations and be of the correct construction for the type of gas being used.

3 Make sure that the hose is tightly and securely fitted at both ends.

4Use a standard hose clamp (not supplied) to fasten the hose.

Connecting the appliance to LPG

1If not already fitted, fit the LPG adaptor on the inlet pipe, making sure that you place the sealing washer between them (as shown in Fig. 5a).

Important!

The LPG hose holder is formed by screwing the LPG hose adaptor into the bottom end of the NATURAL/ TOWN GAS hose holder, (with the sealing washer placed in between them).

2Connect the cooktop to the gas supply using a suitable rubber hose (internal diameter 8 mm). The hose must comply with the applicable local regulations and be of the correct construction for the type of gas being used.

3Make sure that the hose is tightly and securely fitted at both ends.

4Use a standard hose clamp (not supplied) to fasten the hose.

5Install a gas pressure regulator.

Important!

To comply with applicable local regulations, a gas pressure regulator (conforming to the current local regulations) must be installed when connecting the appliance to an LPG cylinder.

When connecting the appliance to the gas supply with a rubber hose, make sure that the hose is as short as possible, without twists or kinks.

the hose is not longer than 750 mm (or refer to applicable local regulations) and does not come into contact with sharp edges, corners or moving parts. Use a single rubber hose only; never connect the appliance with more than one rubber hose.

the hose is not under tension, twisted, kinked, or too tightly bent, neither while the appliance is in use nor while it is being connected or disconnected.

the hose does not come into contact with any part of the appliance with a surface temperature of 70°C or above (or refer to applicable local regulations).

the hose is not subject to excessive heat by direct exposure to flue products or by contact with hot surfaces.

the hose can easily be inspected along its entire length to check its condition.

the hose is replaced at the printed due date or if it shows signs of wear or damage, and replaced regardless of its condition after a maximum of three years.

you inform the customer that the gas cylinder valve or the gas supply valve immediately by the appliance should be closed when the appliance is not in use.

you inform the customer that the hose should not be subjected to corrosion by acidic cleaning agents.

EN 14 Installation instructions

After connecting the appliance to the gas supply, make sure that you

check the piping and connections using a soapy solution. The presence of bubbles indicated a leak. Tighten or replace connectons as appropriate, then recheck for leaks.

Important!

Do not use any naked flame to check for leaks.

check whether the injectors are correct for the type of gas being used. If not, follow the instructions under “Converting the cooktop to a different gas type”.

replace the sealing washer/s on the slightest sign of deformation or imperfection. The sealing washer/s is/are the part/s which guarantee/s a good seal in the gas connection.

Gas connection with rigid pipes or a flexible hose

The gas connection fitting (Fig. 5b) is made up of: the appliance inlet pipe:

the floating nut; the brass elbow; the washers.

Gas connection with rigid pipes or a flexible hose

Note: if already fitted on the inlet pipe, remove the rubber hose holder

½” G cylindrical

 

 

(ISO 228-1)male

Washer

 

Brass

Floating nut

elbow

 

 

Turning the

 

Appliance

gas connection

 

fitting

½” G cylindrical

inlet

 

pipe

Washer

(ISO 228-1)male

 

 

 

Fig. 5b Gas connection with rigid pipes or a flexible hose

½” G cylindrical

½” G cylindrical

(ISO 228-1)female

(ISO 228-1)female

Flexible pipe

 

(not supplied)

Rigid pipe

 

(not supplied)

Important !

If fitted, remove the rubber hose holder from the terminal fitting of the inlet pipe.

When connecting the appliance to the gas supply with rigid pipes or a flexible hose ensure: you use rigid pipes or a flexible hose compliant with applicable local regulations. The flexible hose shall be of the correct construction for the type of gas being used and of the correct size to maintain the heat output of the appliance.

the connection with rigid metal pipes does not cause stress or pressure to the gas piping. the flexible hose is not under tension, twisted, kinked, or too tightly bent, neither while the cooktop is in use nor while it is being connected or disconnected.

Installation instructions 15 EN

the flexible hose is not longer than 2000 mm (or refer to applicable local regulations) and does not come into contact with sharp edges, corners, or moving parts, as these may cause abrasion. Use a single flexible hose only; never connect the appliance with more than one flexible hose. the flexible hose can easily be inspected along its entire length to check its condition; if it has an expiry date, it should be replaced before that date.

if using a flexible hose which is not entirely made of metal, make sure that it does not come into contact with any part of the cooktop with a surface temperature of 70oC or above (or refer to applicable local regulations).

the rigid pipe or flexible hose is replaced if it shows signs of damage.

the flexible hose is not subject to excessive heat by direct exposure to flue products or by contact with hot surfaces.

a gas pressure regulator, in compliance with the applicable local regulations, is installed when connecting to an LPG cylinder.

the socket into which the plug of the flexible hose fit is permanently attached to a firmly fixed gas installation pipe and is positioned so that the hose hangs freely downwards.

the plug of the flexible hose is accessible after installation, so that it can be disconnected for service or removal.

you inform the customer that the gas cylinder valve or the gas supply valve immediately by the cooker should be closed when the appliance is not in use.

you inform the customer that the rigid pipe or flexible hose should not be subjected to corrosion by cleaning agents.

After connecting the appliance to the gas supply, make sure that you

check the piping and connections using a soapy solution. The presence of bubbles indicated a leak. Tighten or replace connectons as appropriate, then recheck for leaks.

Important!

Do not use any naked flame to check for leaks.

check whether the injectors are correct for the type of gas being used. If not, follow the instructions under “Converting the cooktop to a different gas type”.

replace the sealing washer/s on the slightest sign of deformation or imperfection. The sealing washer/s is/are the part/s which guarantee/s a good seal in the gas connection.

Testing operation

The operation of the appliance MUST be tested before leaving. Turn on the gas and light each burner. Check for a well-definedblue flame without any yellow tipping. If any abnormailty is evident, check that the burner cap is located properly and the injector nipple is aligned correctly. Check the minimum burner setting by quickly rotating the burner knobs from the maximum

to the minimum position: the flame must not go out. If the adjustment is required, see section ‘Adjusting a burner’s minimum gas rate setting’ following.

If satisfactory performance cannot be obtained, check the installation and notify the local gas supply authority of a gas supply problem, or if it is an appliance problem, Customer Care should be called to obtain the nearest authorised Service Agent.

EN 16 Installation instructions

Converting the cooktop to a different gas type

Important!

Only a suitably qualified and registered person may convert the cooktop to a different gas type.

To convert from one gas type to another, you need to replace the injectors, and then adjust the minimum gas rate setting.

Replacing the injectors

1Remove the pan supports and burners from the cooktop.

2Using a spanner, remove the injectors and replace them with ones suitable for the type of gas

you are converting the cooktop to. See the ‘Table for the choice of injectors’. The burners are designed so that regulation of primary air is not required.

Injector

J

InjectorJ

Fig. 6 Semi-rapidburners

Fig. 7 Triple-ringwok burners

Adjusting a burner’s minimum gas rate setting

Check whether the flame spreads to all burner ports when the burner is lit with the gas valve set to the minimum position. If some ports do not light, increase the minimum gas rate setting. Check whether the burner remains lit even when the gas valve is turned quickly from the maximum to the minimum position. If the burner does not remain lit, increase the minimum gas rate setting.

To adjust the minimum gas rate setting

1 Make sure the burner is lit.

2Turn the knob to the minimum position.

3

Remove the knob.

Adjustment

4

Using a screwdriver, turn the adjustment screw

screw

until the flame setting is correct.

For LPG, tighten the adjustment screw completely.

Fig. 8 Adjusting a burner’s minimum gas rate setting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Installation instructions

 

 

 

 

 

 

 

 

 

 

17

EN

 

 

Table for the choice of injectors

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BURNER TYPE

 

 

 

 

Semi-rapid

Triple-ring

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOMINAL POWER (W)

 

 

 

1750

 

3500

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REDUCED POWER (W)

 

 

 

450

 

1500

 

 

 

 

 

 

 

 

 

 

 

 

Additional

 

 

Additional

 

 

 

 

 

 

 

 

 

 

marking

 

 

marking

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INJECTOR

Natural Gas

 

20mbar

 

97

 

Z

135

 

T

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(1/100mm

LPG

 

29mbar

 

65

 

-

95

 

-

 

 

 

 

 

or marking)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Town Gas

 

8mbar

 

190

 

2

340

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

By-pass

Natural Gas

 

20mbar

 

 

Adjustable

 

Adjustable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LPG

 

29mbar

 

34

 

-

65

 

-

 

 

 

 

 

(1/100mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Town Gas

 

8mbar

 

 

Adjustable

 

Adjustable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EN 18 Installation instructions

Electrical connection

Important!

This appliance must be earthed.

Installation must be carried out according to the manufacturer’s instructions.

Incorrect installation may cause harm and damage to people, animals or property, for which the manufacturer accepts no responsibility.

If the installation requires alterations to the domestic wiring system, call a qualified electrician. The electrician should also check that the socket cable section is suitable for the power drawn by the appliance. Before carrying out any work on the electrical section of the appliance, it must be disconnected from the power supply.

The appliance must be connected to the mains power supply checking that the voltage corresponds to the value given in the rating plate and that the electrical cable sections can withstand the load specified on the plate.

If the appliance is supplied without a plug, fit a standard plug which is suitable for the power consumed by the appliance.

The plug must be connected to an earthed socket in compliance with safety standards.

Do not use adapters, reducers, a multi-outletpower board or branching devices when connecting this appliance to the mains power supply, as doing so can cause overheating and burning.

A suitable isolating switch providing full disconnection from the mains power supply must be incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. The switch must be of an approved type and provide a 3 mm air gap contact separation in all poles in accordance with the local wiring rules. The switch or socket must be accessible with the appliance installed.

The power supply cable must not touch any hot parts and must be positioned so that it does not exceed 75°C at any point along its length.

If the power supply cable is damaged, it must be replaced by a cable of the same type. It can only be replaced by the manufacturer, its Service Agent or a similarly qualified person in order to avoid a hazard.

As the colours of the wires in the power supply cable of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

Colour of power supply cable wire

Colour or mark of plug terminal

Green & Yellow

“E” (Earth) or green or

 

 

 

 

 

 

Blue

“N” (Neutral) or black

Brown

“L” (Live) or red

Power supply cable section

230 V

 

 

 

 

 

 

 

 

 

 

 

 

Type H05V2V2-F,resistant to temperature of up to 90oC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power supply

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

230 V~ 50 Hz 3 x 0.75 mm2

L1 PE N(L2)

Fig. 9 Connection diagram

Installation instructions 19 EN

Final checklist

TO BE COMPLETED BY THE INSTALLER

Have you installed the clamps?

Have you clamped the cooktop to the bench securely?

Have you used the supplied washers?

Have you leak-testedall connections?

Is the cooktop set for the correct gas type and pressure?

Are the injector sizes correct for the gas type?

Is the cooktop earthed?

Check that the power supply cable is NOT touching the cooktop.

OPERATION:

Do all burners ignitie individually and in combination?

Do the burners remain lit when turned down?

Are the flames consistent and appropriately sized?

Have you demonstrated the basic operation to the customer?

Installer’s name:

Installer’s signature:

Installation company:

Date of installation:

LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER

EN 20 Introduction

About your new cooktop

Thank you for buying a Fisher & Paykel gas cooktop. Once it is installed and ready to use, you will want to know everything about it to make sure you get excellent results right from the start. This guide introduces you to all its special features. We recommend you read the whole guide before using your new cooktop, for both safety and cooking success.

For more information, visit our local website listed on the back cover.

Before using your new cooktop

Before using your new cooktop, please:

read this user guide, taking special note of the ‘Safety and warnings’ section ensure the power supply to the cooktop is turned on.

1

2

 

2

Fig.10 Cooktop layout

 

 

3

4

5

1

Semi-rapidburner

3

Left triple-ringwok burner knob

2

Triple-ringwok burner

4

Semi-rapidburner knob

 

 

5

Right triple-ringwok burner knob

Using your cooktop 21 EN

Gas burners

The knob (Fig. 11) controls the flow of gas through the safety valve.

Never cook or leave the knob between maximum and O (off).

Maximum

You can choose to cook at any heat between minimum and maximum

OFF (closed

valve)

Minimum

Fig.11 Burner knob

Using the burners

1Choose the knob for the burner you want to use.

2Press the knob down gently and turn it anticlockwise to

the maximum position. The ignitors on all the burners will

 

spark.

 

3 Hold down the knob for approximately 10 seconds after

2

the burner has lit.

 

Releasing the knob too soon will extinguish the flame.

 

4Adjust the flame anywhere between the maximum and minimum positions. Do not adjust the flame between maximum and O (OFF).

1

Fig. 12 Pressing down then turning the burner knob

Note: If the burner does not light within 15 seconds, turn the knob off and wait at least one minute before trying again.

5After use, always turn the knobs to the O (OFF) position.

Flame failure safety feature

The burners have a flame failure probe as well as an ignitor (see Fig 13).

The flame failure probe cuts off the gas supply to the burner if the flame is blown out.

If the flames are accidentally extinguished, turn off the burner and do not try to light it again for at least one minute (to allow the gas to disperse).

EN 22 Using your cooktop

If a burner does not light

Check that:

the cooktop is plugged in and the electricity is switched on the gas is turned on

the gas bottle is not empty (if you are using bottled gas) you have held down the knob for at least 10 seconds

the ignitors are sparking. If the ignitors are not sparking, they may be dirty or wet. Clean them with a toothbrush and methylated spirits, as shown in Fig. 13.

Flame failure probe

Ignitor

Ignitor

Fig.13 Cleaning the ignitor and probe

If the flame is irregular

If the flame is yellow or irregular, check that the burner parts, including the burner cap, are: clean and dry

positioned correctly as shown in the ‘Care and cleaning’ section. See also ‘Troubleshooting’.

Using your cooktop 23 EN

Matching cookware to burner

Use flat-bottomedpans, and make sure they match the size of the burner, as shown in the following table. A small pot on a large burner is not efficient.

Diameters of pans which may be used on the cooktop

Burners

Minimum

Maximum

Semi-rapid

16 cm

24 cm

Triple-ringwok

24 cm

28 cm

Maximum diameter for woks 36 cm

 

Fig. 14 Correct and incorrect

Fig. 15 Efficient and inefficient saucepan bottoms

matching of cookware and burner size

 

Note

Do not place large pots or heavy weights on the pan supports. These can bend the pan supports and/or deflect the flame and may result in damage to the cooktop.

Do not place a flame tamer, asbestos mat or other object between the pan and pan support. Doing so may result in damage to the cooktop

Locate the pan centrally over the burner so that it is stable and does not overhang the pot supports.

Wok stand

The wok stand fits over the triple-ringwok burner pan support.

Important!

WRONG

CORRECT

Fig. 16 Correct placement of wok stand

Using a wok without the stand may cause the wok to tip or the wok burner to operate incorrectly. Do not use the stand for ordinary, flat-bottomedsaucepans.

The wok stand MUST BE PLACED ONLY over the pan support for the triple-ringwok burner.

Do not remove the pan support when using the wok stand. Using the wok stand without the pan

supports will deflect the heat downwards and may result in damage to the cooktop. Use only the supplied wok stand or one recommended by the manufacturer.

EN 24 Using your cooktop

Symbols on the glass

Do not place anything, e.g. flame tamer, asbestos mat, between pan and pan support as serious damage to the appliance may result.

Do not remove the pan support and enclose the burner with a wok stand as this will concentrate and deflect the heat onto the hotplate.

Do not use large pots or heavy weights which can bend the pan support or deflect the flame onto the hotplate.

Locate pan centrally over the burner so that it is stable and does not overhang the appliance.

Use only a wok support supplied or recommended by the manufacturer of the appliance.

Using your cooktop 25 EN

Important!

Before any cleaning or maintenance, make sure that: all the burners are turned off

the cooktop is disconnected from the power supply

all parts of the cooktop are cool enough to safely touch.

Important!

For safety reasons, never unscrew the burner plate fixing screws. The burner plates can only be removed by an authorised service agent.

Fig. 17 Never unscrew the burner plate fixing screws

General advice

Clean the cooktop after every use – do not allow stains to become burnt on. See the cleaning chart following.

Clean the burners and ignitors at least once a month. See the cleaning chart following.Once every 3 or 4 years, contact your local Authorised Service Centre and have all the gas

components of your cooktop thoroughly checked, even if your cooktop is functioning correctly. Do not leave acidic substances (lemon juice, vinegar etc) on the surfaces.

Anything that melts onto the glass surface or food spills with a high sugar content may cause pitting of the glass surface if left there to cool. Using extreme caution around hot surfaces, remove these spills immediately with a fish slice or palette knife.

Do not use harsh, abrasive cleaners or unsuitable scourers, as these may scratch the glass. Do not clean cooktop parts in a self-cleaningoven.

Do not use a steam cleaner to clean any part of your cooktop.

EN 26 Care and cleaning

Cleaning chart

What?

 

How?

Important!

Knobs

1

Clean with hot soapy water.

 

 

2

Dry thoroughly with a soft

 

 

 

cloth.

 

 

 

 

 

Glass surface

1

Remove the pan supports,

 

 

 

burner caps, and flame

 

 

 

spreaders.

 

 

2

Remove any spills or burnt-on

 

 

 

food.

 

 

3

Apply ceramic glass cooktop

 

 

 

cleaner.

 

 

4

Wipe with a clean, damp cloth

 

 

 

and dry.

 

Remove stains left by sugary food or spillovers as soon as possible. If left to burn on or cool, they may be difficult to remove or even permanently damage the glass surface.

Take extreme care when working around hot surfaces! Heavy-dutyscourers, some nylon scourers and harsh/ abrasive cleaning agents may scratch the glass. Always read the label to check if your cleaner or scourer is suitable.

Pan supports, burner caps

1

Remove parts, then soak to

 

 

and ring

 

remove stubborn stains, then

 

 

 

 

wash with hot soapy water.

 

 

 

2

Rinse, then dry with a soft

 

 

 

 

cloth.

 

 

 

 

 

 

 

Flame

1

Use a stiff nylon brush or a

 

 

spreaders

 

straightended paper clip to

 

 

 

 

clear the holes and notches.

 

 

 

 

 

 

 

2 Wash with hot soapy water.

 

 

 

3

Rinse and wipe dry.

 

 

Make sure you replace the burner parts correctly, as shown in the drawings following.

Do not use the burners without all its parts correctly in place.

Dry all burner parts thoroughly before replacing as even small droplets

of water will affect the performance of a burner.

Ignitor

Use a toothbrush

 

and methylated spirits

 

to clean these. See

 

Fig. 13.

Flame failure probe

 

A dirty or wet ignitor will prevent the burner from lighting efficiently.

A dirty probe may prevent the flame failure device from working effectively.

Care and cleaning 27 EN

Replacing the semi-rapidburner and pan support

Ensure that the burner and pan support assembly is: unable to rotate

stable and level correctly aligned.

Pan support

Cap

Flame

spreader Flame

failure

probe

 

Use the correct

Ignitor

pan support

only

Rubber washer (x 4)

Notch to be fitted above the teeth

Teeth (x 2) to restrain the pan support

Fig. 18 Ensure the burner and pan support are replaced correctly

EN 28 Care and cleaning

Replacing the triple-ringwok burners and pan supports

Ensure that the burner and pan support assembly is: unable to rotate

stable and level correctly aligned.

Flame spreader

Flame failure probe

Ignitor

Rubber

washer (x 4)

Use the correct pan support only

Notch to be fitted above the teeth

Teeth (x 2)

to restrain

the pan support

Ring

Cap

Fig. 19 Ensure the burner and pan support are replaced correctly

Care and cleaning 29 EN

Cleaning the triple-ringwok burners cup

Important!

Pay special attention to the triple-ringwok burners.

The four holes around the outside of the burner cup must always be kept clean.

This is necessary to ensure the correct and safe operation of the burner.

When cleaning:

remove the flame spreader

use a cotton bud, toothbrush or some other item to clean out any incrustation or dirt from the four holes.

Hole (x 4)

Fig. 20 Cleaning the triple-ringwok burner cup

EN 30 Troubleshooting

Problem

Possible solutions

A burner does not light

Check the cooktop is plugged in and the electricity is switched on.

 

Check the gas supply valve is turned on and the supply to the

 

house is working. You should hear the gas when you turn a burner

 

on.

 

If you use bottled gas, check the gas bottle is not empty.

 

The ignitors may be dirty. Clean them with a toothbrush and

 

methylated spirits.

 

The burner parts may not be located properly. Check the assembly

 

and make sure the burner cap is sitting flat.

 

 

My burner flames are

The burner parts may not be located properly. Check the assembly

yellow or hard to start

and make sure the burner cap is sitting flat.

 

If you use bottled gas, this may indicate you are getting near the

 

end of the bottle.

 

Check the burner parts are clean and dry.

 

The gas pressure may not be at the correct level. Check with your

 

service person or installer.

 

Your cooktop may not be set up for the gas you are using. Check

 

this with your service person or installer.

 

 

One of my burners has an

Check the burner parts are clean and dry. Check the burner is

uneven flame

assembled correctly and make sure the burner cap is sitting flat.

 

 

The flame goes out at low

The gas supply pressure may be low. Check this with your service

settings

person or installer.

 

The low setting may have been adjusted incorrectly. Check this

 

with your service person or installer.

 

If you use bottled gas, this may indicate you are getting near the

 

end of the bottle.

My burners do not turn down much (when running on bottled gas or LPG)

Your cooktop may not have been adjusted correctly. Check this with your service person or installer.

The flame tips are very yellow

Call your service person to service the cooktop.

There are objectionable Call your service person to service the cooktop.odours

The flame appears to lift off the burner

Call your service person to service the cooktop.

There is an electricity

If there is an electricity failure, you can still use your cooktop.

failure

Light the burners by holding a match close to the side of the

 

burner and turning the knob to the Maximum position. Wait until

 

the flame is burning evenly before adjusting.

 

 

Warranty and service 31 EN

Before you call for service or assistance ...

Check the things you can do yourself. Refer to the installation instructions and your user guide and check that:

1your product is correctly installed

2you are familiar with its normal operation.

If after checking these points you still need assistance, please refer to the Service & Warranty book for warranty and after-salesservice details or contact us through our local website listed on the back cover.

Product details

Fisher & Paykel Ltd

Model

Serial no.

Date of purchase

Purchaser

Dealer

Suburb

Town

Country

 

 

35

CN

 

36

 

 

 

39

 

 

53

 

 

54

 

 

59

 

 

63

 

 

64

 

的斐雪派克经销商。

CN 36

必须连接良好接地线。

必须根据这些说明、当地燃气安装法规、城市建筑法律、电气布线法规和其他任何相关法规的 要求安装燃气灶。

确燃烧。

37 CN

切勿触摸发热的燃气灶零部件、灶头、三脚架/

气雾剂。

性油脂。

CN 38

够不到手柄。

OFF

伤害。

39 CN

A

C B

E

D

H

G

F

(mm)

 

 

CG733

A

 

730

B

 

430

C

 

53

D

 

700

E

 

400

F

 

705

G

 

405

H

 

120

 

 

 

 

 

 

CN 40

A

E

B

C

D

(mm)

 

 

CG733

A

 

 

 

 

60

 

 

 

B

 

650

 

800

 

 

650

 

 

500

C

 

 

 

 

213

D

 

 

 

 

83

E

 

450

 

 

 

 

 

 

 

 

41 CN

影响你的公共责任险。

105oC 1

距离燃气灶底面至少30mm

30 mm

1

CN 42

通风口截面积不得小于100cm2 2a 2b

安装并连接此类装置。同时要特别注意让厨房保持良 好通风。

2a 3-52b “”

 

PP

 

 

 

 

2a

 

2b

43 CN

3 (S) (R) 34

40mm 20-40mm

R S

R

S

S R

S R

3

40 mm

20 mm

30mm

4

CN 44

* **

* / /

 

 

 

 

45 CN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

/

 

 

 

 

 

 

 

 

 

 

 

 

½" G

 

 

 

 

(ISO 228-1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

½” G

 

 

 

(ISO 228-1)

 

 

 

 

 

½” G

 

½” G

 

 

(ISO 228-1)

 

(ISO 228-1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13mm

 

 

5a

 

 

8mm

 

 

 

 

 

 

CN 46

1/5a

213mm

15a

/

28mm

4

软管长度不超过750mm70oC 70oC

47 CN

检查是否漏气。

“ ”

5b

 

½” G

 

 

(ISO 228-1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

½" G

 

 

(ISO 228-1)

 

½” G

½” G

 

(ISO 228-1)

(ISO 228-1)

5b

 

 

 

 

 

 

 

 

气灶热量输出要求。

CN 48

2000mm 70oC 70oC

检查是否漏气。

“ ”

参看后面的“ ”

49 CN

2“ ”

J

J

6

7

设置。

1

3

4

8

CN 50

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(W)

 

 

 

1750

 

3500

 

 

(W)

 

 

 

450

 

1500

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

20

97

 

Z

135

 

T

 

 

 

 

 

 

 

 

 

 

 

 

(1/100mm

 

29

65

 

95

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

8

190

 

2

340

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

20

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

29

34

 

65

 

 

 

(1/100mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

51 CN

必须根据制造商的安装说明进行安装。

隔为3mm 75°C

 

 

 

"E"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

"N"

 

"L"

 

 

 

 

230 V

H05V2V2-F90°C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

230V ~ 50Hz 3 x 0.75mm2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L1 PE N(L2)

 

 

 

 

 

 

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CN 52

安装日期

53 CN

“ ”

1

2

2

 

10

 

 

 

 

 

3

4

5

 

1

 

3

 

2

 

4

 

CN 54

11

 

 

O

 

 

 

 

 

 

 

11

 

 

1

 

 

1

 

 

2

 

 

 

 

 

3

10

 

 

 

2

4 位置和O

15

12

5O

13

55 CN

是否按住旋钮至少10

13

13

清洁干燥 在“ ”

CN 56

 

 

 

 

16cm

24cm

 

24cm

28cm

 

 

36cm

14

15

WRONG

 

CORRECT

 

 

 

16

切勿在铁锅锅圈上使用平底锅。 铁锅锅圈只能放在三环铁锅灶头上的平底锅锅圈之上。

57 CN

否则可能会严重损坏燃气灶。

热板。

投向发热板。

CN

58

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

17

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

59

 

 

 

 

CN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

2

 

 

 

 

1

 

 

 

 

 

 

 

 

2

 

 

 

3

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

坏玻璃表面。

清洁剂和擦子是否适合擦拭 玻璃表面。

1

2擦干。

1

2

也会影响灶头燃烧性能。

 

 

 

 

 

 

 

13

 

 

 

 

 

 

 

 

 

 

CN 60

不能旋转 水平稳定 正确对准

(4 )

固定齿(2 )

18

61 CN

不能旋转 水平稳定 正确对准

(4 )

固定齿(2 )

19

CN 62

取下分火盘

(4 )

20

 

63

 

 

CN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CN 64

“ ”

Fisher & Paykel Ltd

 

 

 

 

 

 

 

 

www.fisherpaykel.com.sg

www.fisherpaykel.asia

Copyright © Fisher & Paykel 2012. All rights reserved.

The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available.

Copyright © Fisher & Paykel 2012.

SG HK

F&P PN - 590453 A F&P ITALY PN - 1104054-ß1

04.2012