ENGLISH - PAGES 4-5
®
READ ALL INSTRUCTIONS
BEFORE OPERATING UNIT! 
ESPAÑOL - PÁGINAS 6-7
¡LÉANSE ANTES DE UTILIZAR EL APARATO Y GUARDENSE PARA SU USO POSTERIOR!
FRANçAIS - PAGES 8-9
PRIERE DE LIRE AVANT L’EMPLOI ET A
CONSERVER POUR UTILISATION ULTERIEURE!
ITALIANO - PAGINE 10-11
LEGGERE ATTENTAMENTE PRIMA DELL’USO E
CONSERVARE PER UN UTILIZZO SUCCESSIV0!
DEUTSCH - SEITEN 12-13
BITTE VOR GEBRAUCH LESEN UND FÜR
SPÄTEREN
GEBRAUCH AUFBEWAHREN!
- 14-15
2
•TO PREVENT DAMAGE, FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
•NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED PERSONNEL 
ONLY.
•DO NOT ALTER THE AC PLUG. 
•PARA EVITAR DAÑOS, INCENDIOS Y DESCARGAS ELÉCTRICAS, NO EXPONGA ESTA UNIDAD A LA LLUVIA NI A LA HUMEDAD.
•CONTIENE PIEZAS CUYO MANTENIMIENTO NO LO PUEDE REALIZAR EL USUARIO, SINO SÓLO PERSONAL CUALIFICADO.
•POUR EVITER L'ENDOMMAGEMENT DE L'APPAREIL, UN DEPART D'INCENDIE, OU UN CHOC ELECTRIQUE, NE L'EXPOSEZ JAMAIS A L'HUMIDITE OU A LA PLUIE.
•AUCUNE MAINTENANCE NE DOIT ETRE EFFECTUEE POUR LES PIECES SITUEES DANS L'APPAREIL. LES REPARATIONS ET LA MAINTENANCE DOIVENT ETRE EXECUTEES UNIQUEMENT PAR UN PERSONNEL QUALIFIE.
•PER EVITARE DANNI, RISCHI DI INCENDI O SCOSSE ELETTRICHE, NON ESPORRE QUESTA UNITÀ ALLA
PIOGGIA O ALL'UMIDITÀ.
•NON CONTIENE PARTI RIPARABILI DALL'UTENTE: FARE ESEGUIRE LA MANUTENZIONE SOLTANTO DA
PERSONALE QUALIFICATO.
• THIS UNIT MUST BE EARTH GROUNDED.
•UNPLUG THE AC POWER LINE CORD BEFORE CLEANING THE UNIT’S COVERING WITH ONLY A DAMP CLOTH; WAIT UNTIL THE UNIT IS COMPLETELY DRY BEFORE RECONNECTING IT TO POWER.
•NO MODIFIQUE EL ENCHUFE DE CA.
•ESTA UNIDAD DEBE CONECTARSE CON TOMA DE TIERRA.
•DESCONECTE EL CABLE DE ALIMENTACIÓN DE CA ANTES DE LIMPIAR LA CUBIERTA DE LA UNIDAD; ESPERE A QUE LA UNIDAD ESTÉ COMPLETAMENTE SECA ANTES DE VOLVER A CONECTARLA A LA CORRIENTE.
•NE MODIFIEZ PAS LA PRISE DE CA.
• CET APPAREIL DOIT ETRE MIS A LA TERRE.
•DEBRANCHEZ LE CABLE D'ALIMENTATION AVANT DE NETTOYER LE BOITIER DE L'APPAREIL ET ATTENDEZ
QUE
L'APPAREIL SOIT COMPLETEMENT SEC AVANT DE LE REBRANCHER SUR LE SECTEUR.
•NON ALTERARE LA PRESA C.A.
•QUESTA UNITÀ DEVE ESSERE COLLEGATA A TERRA.
•DISCONNETTERE IL CAVO DI ALIMENTAZIONE C.A. PRIMA DI PULIRE LA COPERTURA DELL'UNITÀ; ATTENDERE CHE L'UNITÀ SIA COMPLETAMENTE ASCIUTTA PRIMA DI RICOLLEGARLA ALL'ALIMENTAZIONE.
•SETZEN SIE DIESES GERÄT NIEMALS REGEN ODER • MANIPULIEREN SIE AUF KEINEN FALL DIE NETZAN-
FEUCHTIGKEIT AUS, UM BESCHÄDIGUNG, BRANDENTWICKLUNG UND ELEKTRISCHE SCHLÄGEN ZU VERMEIDEN.
•IM GERÄT SIND KEINE ZU WARTENDEN TEILE. WARTUNG UND REPERATUREN DÜRFEN NUR VON QUALIFIZIERTEN TECHNIKERN DURCHGEFÜHRT WERDEN.
SCHLUSSBUCHSE.
•DAS GERÄT MUSS GEERDET SEIN.
•STECKEN SIE DAS NETZKABEL AUS, BEVOR SIE DAS
GEHÄUSE DES GERÄTS REINIGEN. SCHLIESSEN SIE DAS GERÄT
ERST WIEDER ANS STROMNETZ AN,
WENN ES VOLLSTÄNDIG GETROCKNET IST.
3
Fender® Roc Pro™ 1000
Congratulations on your purchase of a Fender® Roc•Pro™ 1000 amplifier. Both the “combo” and the “head only” are covered in this manual and all features are the same, except where noted. Your Roc•Pro 1000 is equipped with the features that today’s musicians demand:
•Two channels with independent tone controls.
•Both vacuum-tube and solid-state circuits offering the best of both technologies in one hybrid amplifier.
•A choice of two pre-amplifiers in the drive channel, using a 12AX7 / ECC83 tube for its well known warmth of tone.
•100 watts of power.
•Rear panel effects loop jacks with three output-level settings compatible with pedal and rack-mounted devices.
•Quasi-balanced line out jack for connection to sound equipment.
•External-speaker jack for output to an additional speaker enclosure.
•Footswitch (included) for remote switching of the reverb effect, channel selection and gain selection.
•Aluminum chassis to reduce magnetic and radio interference.
•Automatic electric fault protection.
•Classic Fender spring-reverb effect.
•Genuine Tolex® covering for long lasting good looks.
•Rugged metal speaker grill.
|
|
|
|
|
Front Panel Functions |
|
|
|
||||||
1 |
2 |
4 |
5 |
6 |
7 |
9 |
11 |
12 |
13 |
15 |
16 |
17 |
18 |
20 |
|
|
3 |
|
|
8 |
10 |
|
|
|
14 |
|
|
|
19 |
1.INPUT - Plug in your guitar at this jack.
•NOTE: The Normal channel must be selected for items 2-6 to function. See DRIVE SELECT (item 14)
2.VOLUME - Adjusts the loudness of the amplifier.
3.MID SHIFT - Switch IN shifts up one octave the frequency range controlled by the MID knob (item 5). This offers control over a slightly higher range of your signal. Switch OUT shifts the MID range down one octave to its original position.
4.TREBLE - Adjusts the high frequency level.
5.MID - Adjusts the mid frequency level in the range selected by the MID SHIFT button (item 3).
6.BASS - Adjusts the low frequency level.
•NOTE: The Drive channel must be selected for items 7-13 and 15 to function. See DRIVE SELECT (item 14). Either GAIN 1 (Red) OR GAIN 2 (Yellow) can be selected as the active pre-amp in the Drive channel. See
GAIN SELECT (item 8).
7.GAIN 1 - Adjusts the pre-amp level (distortion/sustain) while the Red pre-amp is active. Lower settings provide a gradual compression distortion and higher settings provide more sustain. GAIN 1 must be used in conjunction with the Drive channel VOLUME (item 15) to set the overall volume of the amplifier.
8.GAIN SELECT - One of two pre-amp circuits can be selected for the Drive channel. Switch OUT selects the Red Drive channel pre-amp (GAIN 1). Switch IN selects the Yellow Drive channel pre-amp (GAIN 2).
9.GAIN 2 - Adjusts the pre-amp level (distortion/sustain) while the Yellow pre-amp is active. Lower settings provide a gradual compression distortion and higher settings provide more sustain. GAIN 2 must be used in conjunction with the Drive Channel VOLUME (item 15) to set the overall volume of the Yellow Drive Channel.
10.PRE-AMP INDICATORS - The red LED illuminates while the Red pre-amp (GAIN 1) is active. The yellow LED illuminates while the Yellow pre-amp (GAIN 2) is active.
11.TREBLE - Adjusts the post-distortion high frequency level .
12.MID - Adjusts the middle frequency level.
13.BASS - Adjusts the post-distortion low frequency level.
14.DRIVE SELECT - Switch IN selects the Drive channel. Switch OUT selects the Normal channel.
15.VOLUME - Adjusts the loudness of the amplifier. Must be used in conjunction with the currently active preamp GAIN control (1=Red or 2=Yellow).
•NOTE: Both the Normal and Drive channels are affected by items 16-20.
16.REVERB - Adjusts the reverb effect level in both channels.
17.EFFECTS MIX - Adjusts the effects (wet) level signal while using the rear panel effects loop option.
18.FOOTSWITCH (Included) - Plug in the footswitch here. The footswitch enables switching between Normal and Drive channels, between Red and Yellow pre-amps and ON/OFF switching of the REVERB effect.
•NOTE: When plugged in, the footswitch disables the front panel select buttons. Connect the footswitch using a speaker grade cord rather than a coaxial guitar cord.
19.POWER INDICATOR - This LED illuminates when the amplifier is ON and receiving power.
20.POWER SWITCH - Switches the amplifier ON and OFF.
4
Rear Panel Functions
2 |
3 |
|
|
|
|
4 |
5 |
6 |
7 |
1.LINE CORD - Connect the power line cord to a grounded AC receptacle in accordance with the voltage and frequency ratings as listed on the rear panel of the amplifier.
2.8 OHM SPEAKER JACK (Combo & Head models) - Plug-in connection for external 8 ohm speakers only.
3.4-OHM ADDITIONAL SPEAKER JACK (Head model only) - Plug-in connection for a external 4 ohm speaker or a second 8 Ohm speaker enclosure. The combined minimum impedance for all speaker enclosures should be 4 ohms (i.e. two 8 ohm enclosures in parallel).
4.LINE OUT - This jack provides a signal output suitable for connection to recording and sound reinforcement equipment. Using a 3-conductor stereo cord will provide a quasi-balanced signal and a 2-conductor mono cord will provide an unbalanced signal.
5.SEND - Connect cord to external equipment at this output jack. This unbalanced jack provides a prereverb signal output from the preamp and may be used to drive effects units in an effects loop, to drive additional amplifiers in a multi-amp set up or as a preamp send to a mixing console.
6.LEVEL SWITCH - This switch directly effects the SEND jack (item 5) by boosting or attenuating the signal sent to the effects. External rack effects usually require –7dB or +4dB settings. Effects pedals usually require a –16dB setting.
7.RETURN - Connect cord from external effects devices at this input jack. Inserting a plug at this jack automatically disconnects the unit’s internal connection from the pre-amp to the power amp. This jack is prereverb and can also be used as a power amp input. Plugging into this jack activates the EFFECTS MIX control on the front panel.
Specifications
TYPE: |
|
PR 209 |
|
|
|
PART NUMBERS: |
(Combo) |
|
|
|
(Head) |
22-6808-000 (120V, 60 Hz)USA; 22-6868-000 (230V, 50 Hz)Euro; |
|
22-6807-000 (120V, 60 Hz)USA; 22-6867-000 (230V, 50 Hz)Euro; |
|||
22-6838-000 (240V, 50 Hz)Aust; 22-6878-000 (100V, 50/60 Hz)Jpn |
22-6837-000 (240V, 50 Hz)Aust; 22-6877-000 (100V, 50/60 Hz)Jpn |
||||
POWER REQUIREMENTS: |
|
300W |
|
|
|
INPUT IMPEDANCE: |
|
> 1 MΩ |
|
|
|
NOMINAL LEVEL: |
|
100mV |
|
|
|
POWER OUTPUT: |
|
69W into 8Ω at 5% THD |
94W into 4Ω at 5% THD |
||
EFFECTS LOOP: |
NOMINAL LEVEL: |
Selectable +4, -7, -16 dBv |
|
||
|
OUTPUT IMPEDANCE: |
1.2 kΩ max. |
|
|
|
|
INPUT IMPEDANCE: |
100kΩ |
|
|
|
TUBE COMPLEMENT: |
|
One 12AX7A (ECC83) (P/N 013341) |
|
||
SPEAKER (Combo only): |
|
8Ω, 12” Fender Special Design (P/N 040598) |
|||
EXTERNAL SPEAKER: |
(Combo) |
Fender recommends Guitar enclosure GE-112 Mk II (P/N 21-1660-010) @ 8Ω |
|||
|
(Head) |
Fender recommends Guitar enclosure GE-412 Mk II (P/N 21-1662-010) @ 4Ω |
|||
FOOTSWITCH (Included): |
|
3 button: Gain, Gain Select and Reverb |
|||
DIMENSIONS: |
|
(Combo) |
(Head) |
||
|
HEIGHT: |
17.5 in. |
(44.5 cm) |
8.5 in. |
(21.6 cm) |
|
WIDTH: |
22.5 in. |
(56.8 cm) |
22.5 in. (56.8 cm) |
|
|
DEPTH: |
10.25 in. (25.9 cm) |
9.5 in. |
(24.1 cm) |
|
|
WEIGHT: |
41 lbs. |
(18.6 kg) |
25 lbs. |
(11.4 kg) |
Product specifications are subject to change without notice.
5
Loading...