Fairchild LM2904, LM358, LM358A, LM258, LM258A service manual

!

www.fairchildsemi.com

LM2904,LM358/LM358A,LM258/

LM258A

Dual Operational Amplifier

Features

•Internally Frequency Compensated for Unity Gain

•Large DC Voltage Gain: 100dB

•Wide Power Supply Range:

LM258/LM258A, LM358/LM358A: 3V~32V (or ±1.5V ~ 16V)

LM2904 : 3V~26V (or ±1.5V ~ 13V)

•Input Common Mode Voltage Range Includes Ground

•Large Output Voltage Swing: 0V DC to Vcc -1.5V DC

•Power Drain Suitable for Battery Operation.

Description

The LM2904,LM358/LM358A, LM258/LM258A consist of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltage. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. Application areas include transducer amplifier, DC gain blocks and all the conventional OP-AMP circuits which now can be easily implemented in single power supply systems.

8-DIP

1

8-SOP

1

Internal Block Diagram

OUT1	1			8	VCC
IN1 (-)	2	-		7	OUT2
IN1 (+)	3	+	-	6	IN2 (-)
GND	4		+	5	IN2 (+)

Rev. 1.0.2

©2002 Fairchild Semiconductor Corporation

LM2904,LM358/LM358A,LM258/LM258A

Schematic Diagram

(One section only)

VCC
Q5	Q6			Q12	Q17
						Q19
						Q20
	Q2	Q3				R1
			C1
IN(-)		Q4			Q18
	Q1
						R2
IN(+)			Q11			OUTPUT
						Q21
					Q15
	Q7		Q10
			Q13
	Q8	Q9			Q14	Q16
GND

Absolute Maximum Ratings

	Parameter	Symbol	LM258/LM258A	LM358/LM358A	LM2904	Unit
	Supply Voltage	VCC	± 16 or 32	± 16 or 32	± 13 or 26	V
	Differential Input Voltage	VI(DIFF)	32	32	26	V
	Input Voltage	VI	-0.3 to +32	-0.3 to +32	-0.3 to +26	V
	Output Short Circuit to GND	-	Continuous	Continuous	Continuous	-
	VCC≤ 15V, TA = 25° C(One Amp)
	Operating Temperature Range	TOPR	-25 ~ +85	0 ~ +70	-40 ~ +85	° C
	Storage Temperature Range	TSTG	-65 ~ +150	-65 ~ +150	-65 ~ +150	° C

2

LM2904,LM358/LM358A,LM258/LM258A

Electrical Characteristics

(Vcc = 5.0V, VEE = GND, TA = 25° C, unless otherwise specified)

Parameter	Symbol	Conditions				LM258					LM358					LM2904			Unit
					Min.		Typ.	Max.		Min.		Typ.	Max.		Min.		Typ.	Max.
		VCM = 0V to VCC
Input Offset	VIO	-1.5V			-		2.9		5.0	-		2.9		7.0	-		2.9	7.0	mV
Voltage		VO(P) = 1.4V,
		RS = 0Ω
Input Offset	IIO	-			-		3		30	-		5		50	-		5	50	nA
Current
Input Bias	IBIAS	-			-		45		150	-		45		250	-		45	250	nA
Current
Input Voltage		VCC = 30V							Vcc					Vcc				Vcc
	VI(R)				0		-			0		-		-1.5	0		-	-1.5	V
Range		(LM2904, VCC=26V)							-1.5
		RL = ∞ , VCC = 30V			-		0.8		2.0	-		0.8		2.0	-		0.8	2.0	mA
		(LM2904, VCC=26V)
Supply Current	ICC
		RL = ∞ , VCC = 5V			-		0.5		1.2	-		0.5		1.2	-		0.5	1.2	mA
Large Signal		VCC = 15V,
	GV	RL= 2kΩ			50		100		-	25		100		-	25		100	-	V/mV
Voltage Gain
		VO(P) = 1V to 11V
	VO(H)	VCC=30V		RL = 2kΩ	26		-		-	26		-		-	22		-	-	V
		(VCC
Output Voltage				RL=
		=26V for			27		28		-	27		28		-	23		24	-	V
Swing				10kΩ
		LM2904)
	VO(L)	VCC = 5V, RL= 10kΩ			-		5		20	-		5		20	-		5	20	mV
Common-Mode	CMRR	-			70		85		-	65		80		-	50		80	-	dB
Rejection Ratio
Power Supply	PSRR	-			65		100		-	65		100		-	50		100	-	dB
Rejection Ratio
Channel	CS	f = 1kHz to 20kHz			-		120		-	-		120		-	-		120	-	dB
Separation		(Note1)
Short Circuit to	ISC	-			-		40		60	-		40		60	-		40	60	mA
GND
		VI(+) = 1V,
	ISOURCE	VI(-) = 0V			20		30		-	20		30		-	20		30	-	mA
		VCC = 15V,
		VO(P) = 2V
Output Current		VI(+) = 0V, VI(-) = 1V,
		VCC = 15V,			10		15		-	10		15		-	10		15	-	mA
	ISINK	VO(P) = 2V
		VI(+) = 0V,VI(-) =1V ,
		VCC = 15V,			12		100		-	12		100		-	-		-	-	µ A
		VO(P) = 200mV
Differential	VI(DIFF)	-			-		-		VCC	-		-		VCC	-		-	VCC	V
Input Voltage

Note:

1. This parameter, although guaranteed, is not 100% tested in production.

3

LM2904,LM358/LM358A,LM258/LM258A

Electrical Characteristics (Continued)

(VCC= 5.0V, VEE = GND, unless otherwise specified)
The following specification apply over the range of -25° C ≤						TA ≤ +85° C for the LM258; and the 0° C ≤									TA ≤ +70° C
for the LM358; and the -40° C ≤ TA ≤ +85° C for the LM2904
Parameter	Symbol	Conditions				LM258			LM358				LM2904			Unit
					Min.	Typ.	Max.	Min.		Typ.	Max.	Min.		Typ.	Max.
		VCM = 0V to
Input Offset	VIO	VCC -1.5V			-	-	7.0	-		-	9.0	-		-	10.0	mV
Voltage		VO(P) = 1.4V,
		RS = 0Ω
Input Offset	∆ VIO/∆ T	RS = 0Ω			-	7.0	-	-		7.0	-	-		7.0	-	µ V/° C
Voltage Drift
Input Offset	IIO	-			-	-	100	-		-	150	-		45	200	nA
Current
Input Offset	∆ IIO/∆ T	-			-	10	-	-		10	-	-		10	-	pA/° C
Current Drift
Input Bias	IBIAS	-			-	40	300	-		40	500	-		40	500	nA
Current
Input Voltage		VCC = 30V					Vcc				Vcc				Vcc
	VI(R)	(LM2904 ,			0	-		0		-	-2.0	0		-	-2.0	V
Range							-2.0
		VCC = 26V)
Large Signal		VCC = 15V,
	GV	RL = 2.0kΩ			25	-	-	15		-	-	15		-	-	V/mV
Voltage Gain
		VO(P) = 1V to 11V
		VCC=30V		RL = 2kΩ	26	-	-	26		-	-	22		-	-	V
Output Voltage	VO(H)	(VCC =
		26V for		RL=10kΩ	27	28	-	27		28	-	23		24	-	V
Swing		LM2904)
	VO(L)	VCC = 5V,	RL= 10kΩ		-	5	20	-		5	20	-		5	20	mV
		VI(+) = 1V,
	ISOURCE	VI(-) = 0V			10	30	-	10		30	-	10		30	-	mA
		VCC = 15V,
Output Current		VO(P) = 2V
		VI(+) = 0V,
	ISINK	VI(-) = 1V			5	8	-	5		9	-	5		9	-	mA
		VCC = 15V,
		VO(P) = 2V
Differential	VI(DIFF)	-			-	-	VCC	-		-	VCC	-		-	VCC	V
Input Voltage

4