WASHING MACHINE
User
Manual
FE-7210B - FE-7214B - FE-7212B
CONTENTS
|
BEFORE USING THE APPLIANCE |
|
CHAPTER-1: |
|
|
• |
Safety warnings |
4-5 |
• |
Correct Usage |
6-7 |
• |
General warnings |
8-9-10-11 |
• |
Safety warnings |
12-13-14-15-16-17 |
• |
Packaging and Environment |
18 |
• |
Savings Information |
19 |
|
OVERVIEW OF YOUR DEVICE |
|
CHAPTER-2: |
|
|
• |
General Appearance |
20-21 |
• |
Specifications |
22 |
|
INSTALLATION |
|
CHAPTER-3: |
|
|
• |
Removing transportation safety screws |
23-24 |
• |
Adjusting Adjustable Stays |
25-26-27 |
• |
Electrical connection |
28 |
• |
Water inlet hose connection |
29-30 |
• |
Water discharge connection |
31 |
|
INTRODUCTION OF CONTROL PANEL |
32 |
CHAPTER-4: |
||
• |
Detergent drawer |
33-34 |
• |
Programme knob |
35 |
• |
Electronic display |
36-37 |
|
PRELIMINARY PREPARATION FOR LAUNDERING |
|
CHAPTER-5 |
||
• |
Separating laundries EN -2- |
38-39 |
CONTENTS
•
•
•
•
•
•
•
CHAPTER-6: CHAPTER-7:
•
•
•
•
•
CHAPTER-8: CHAPTER-9: CHAPTER-10:
CHAPTER-11:
•
•
Putting laundries in the machine |
40 |
Adding detergent into machine |
41 |
Operating your machine |
42-43-44 |
Auxiliary Functions |
45-46-47-48-49-50 |
Child lock |
51 |
Cancelling programme |
52 |
Finishing programme |
53 |
PROGRAM TABLE |
54-55-56-57-58-59-60-61-62 |
MAINTENANCE AND CLEANING OF YOUR MACHINE |
|
Warning |
63 |
Water inlet filters |
64 |
Pump filter |
65-66 |
Detergent drawer |
67 |
Liquid detergent apparatus |
67 |
FLUSH STOPPER / BODY / DRUM |
68 |
TROUBLE SHOOTING |
69-70-71-72-73 |
AUTOMATIC FAULT WARNINGS AND |
|
WHAT TO BE DONE |
74 |
PRACTICAL INFORMATION |
75-76-77-78 |
How to read the energy label and saving energy 79-80 |
|
Disposal of your old machine |
81 |
EN -3-
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS)
Operating voltage / frequency: (V/Hz) (220-240) V~/50Hz; Total current (A): 10
Water pressure (Mpa)
Maximum: 1 Mpa / Minimum : 0.1 Mpa Total power (W) : 2200
Maximum dry laundry capacity (kg): 7
Do not install your machine on a carpet or such grounds that would prevent the ventilation of its base.
The appliance is not intended for use by people (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Call the nearest authorized service for a replacement if the power cord malfunctions.
EN -4-
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS)
Use only the new water inlet hose coming with your machine while making water inlet connections of your machine.Never use old, used or damaged water inlet hoses.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Note:For softcopy of this user manual, please contact following address: “washingmachine@standardtest.info”.In your e-mail, please provide the model name and serial number (20 digits) which you can find on the appliance door.
EN -5-
CHAPTER -1: BEFORE USING THE APPLIANCE (CORRECT USAGE)
•Definitely read the user’s manual.
•Your machine is designed to be used 
domestically. Commercial use will
cause your warranty to be cancelled.
•Keep your pets away from your machine.
•Please check the packaging of your machine before installation, and the outer surface after the package is opened. Do not operate damaged machines or machines with opened package.
•Have your machine installed only by authorized service. Any interference to your machine by anyone other than authorized services shall cause your warranty to be void.
•The appliance is not intended for use by people (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
EN -6-
CHAPTER -1: BEFORE USING THE APPLIANCE (CORRECT USAGE)
•Use your machine only for laundries that have been specified as suitable for washing by the manufacturer.
•Before operating the washing machine, remove the 4 transportation screws and rubber spacers from the back of the machine. If the screws are not removed, it may cause heavy vibration, noise and product malfunction, (voiding the guarantee).
•Your machine is not covered under warranty for faults caused by any kind of external factors (pesticides, fire, etc.).
•Please do not throw away this user manual; keep it for future reference. You or somebody else might need it in the future.
Note: Machinery specifications may vary depending on the product purchased.
EN -7-
CHAPTER -1: BEFORE USING THE APPLIANCE (GENERAL WARNINGS)
•The necessary ambient temperature for your machine’s ideal operation is 15-25°.
•Frozen hoses can tear and explode. In regions where temperature is below zero, ambient temperature might endanger the safe operation of electronic card.
•Please ensure that the clothes you will place in your machine do not contain any foreign substances (nail, needle, coins, lighter, matches, clip etc.) in their pockets. These foreign substances can damage your machine.
•Before starting to use your machine, you may call the nearest authorized service and request free-of-charge help for installation, operation and use of your machine.
•It is recommended to perform the first washing operation in 90˚ Cotton programme and without laundry by inserting ½ scale
of detergent in 2nd compartment of the detergent drawer.
EN -8-
CHAPTER -1: BEFORE USING THE APPLIANCE (GENERAL WARNINGS)
•As detergent or softener exposed to air for a long time may cause residues, put your detergent or softener in the detergent drawer at the beginning of every washing.
•It is advised that you unplug your machine and close the water inlet tap if you will not use your machine for a long time. Also, leaving the door of your machine will prevent the formation of bad odors due to humidity.
•Some water might be left in your machine after the trials and tests conducted due to Quality Control procedures. This will not damage your machine.
•Remember that packaging materials of your machine may be dangerous for children.
•Keep the packaging materials in a place where children cannot reach or dispose of them appropriately.
•Use pre-wash programs only for very dirty laundry.
EN -9-
CHAPTER -1: BEFORE USING THE APPLIANCE (GENERAL WARNINGS)
•Never open the detergent drawer when the appliance is running.
•In case of any breakdown, unplug the appliance first and then turn the tap off. Do not attempt to repair by yourself, always contact for authorized service advice.
•The amount of laundry you put in your washing machine should not exceed the maximum amount indicated.
•Never force the door to open when the machine is running.
•Washing floury clothes in your 
machine damages the machine. Do not wash floury clothes in your machine.
EN -10-
CHAPTER -1: BEFORE USING THE APPLIANCE (GENERAL WARNINGS)
• Please adhere to detergent/fabric conditioner manufacturers’ the use of fabric conditioner or similar products in your machine.
•Set up your machine in a place where its door can be completely opened. (Do not set up your machine in places where its door cannot be fully opened.)
•Set up your machine at locations that can be fully ventilated and could have constant air circulation.
EN -11-
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS)
You must read these warnings. You can thus protect yourself and your beloved ones against fatal injuries and risks.
DANGER OF GETTING BURNT!
Do not touch discharging hose and water during discharging as the appliance may reach high temperatures when running.
EN -12-
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS)
DEATH RISK DUE TO ELECTRICAL CURRENT!
• Do not use multiple receptacles or extension cord.
• Do not plug in damaged plug sockets
• Never pull the cable when unplugging – always grip the plug itself.
• Do not plug-in or out the plug from the receptacle with wet hands 
to prevent electrocution!
•Never touch the machine with wet 
hands or feet.
•Call the nearest authorized service for a replacement if the power cord malfunctions.
EN -13-
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS)
Flooding risk!
•Check whether the water runs fast or not before placing the discharge hose on the sink.
•Take necessary measures to prevent the slipping of your hose.
•The backfiring force of a hose that is not placed appropriately can displace the hose. Prevent the stopper inside your sink from blocking the sink hole.
EN -14-
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS)
Danger of Fire!
•Do not keep inflammable liquids near your machine.
•The sulphure content of paint removers might cause corrosion. For this reason, never use paint-removing materials in your machine.
•Never use products that contain solvent material (like washing gas) in your machine.
•Remove all the objects in the pockets of your laundries (needle, paperclip, lighter, matches etc.) when placing them your machine.
Fire and Explosion risk may occur.
EN -15-
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS)
Fall and injury hazard!
•Do not climb on your machine. The upper table of your machine may break and you might get injured.
•Tidy the hose, cable and packaging of your machine during installation. You might trip over and fall.
•Do not turn your machine upside down, or on its side.
•Do not lift your machine by holding it from extruding parts (detergent drawer, door). These parts might break and cause you to get injured.
•There’s the risk of tripping and injury if the materials like hose and cables are not properly stored after your machine is installed.
Machine must be carried by
2 people or more.
EN -16-
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS)
Child safety!
•Do not leave children unattended near the machine. Children might lock themselves up into the machine and death risk might occur.
•Door glass and surface might be extremely hot while your machine
operates. Thus, especially touching the 
machine might give damage to the 
skins of children.
•Keep packaging material away from children.
•Poisoning might occur if the detergent and maintenance materials are consumed, and eyes or the skin might be irritated if they come into contact with the skin. Keep the cleaning materials away from the reach of children.
EN -17-
CHAPTER -1: BEFORE USING THE APPLIANCE PACKAGING AND ENVIRONMENT
Removal of packaging materials
Packaging materials protect your machine from any damage that might occur during transportation. Packaging materials are environment friendly as they are recyclable. Recycling material provides both raw material savings and decreases waste production.
Disposal of old machine
Electrical or electronical old devices
might still contain salvagable parts. So, never throw away your old devices that you do not use into the waste.
Ensure that the parts of your old electronic or electrical devices are reused by giving them to the gathering centres foreseen by related authorities.
Please ensure your old appliances are kept in an appropriate place for the safety of children until they are taken outside the house.
EN -18-
CHAPTER -1: BEFORE USING THE APPLIANCE SAVINGS INFORMATION
Some important information to get more efficiency out of your machine:
•The amount of laundry you put in your washing machine should not exceed the maximum amount indicated.
By this way, your machine shall run in saving mode.
•Not using the pre-wash feature for little and normal-dirty laundry shall save electricity and water.
EN -19-
CHAPTER -2: OVERVIEW OF YOUR DEVICE GENERAL APPEARANCE
Electronic display
Programme knob
Upper Tray
Detergent drawer
Container
Cover of pump filter
EN -20-
CHAPTER -2: OVERVIEW OF YOUR DEVICE GENERAL APPEARANCE
Transportation Safety
Screw
Water Inlet Valve
Discharging Hose
Power Cable
Transportation Safety
Screw
Transportation Safety
Screw
Transportation Safety
Screw
EN -21-
CHAPTER -2: OVERVIEW OF YOUR DEVICE TECHNICAL SPECIFICATIONS
Operating voltage / frequency (V/Hz)
Total current (A)
Water pressure
Total power (W)
Maximum dry laundry capacity (kg)
Spinning revolution (rev / min)
Programme number
Dimensions
(Height x Width x Depth) (mm)
(220-240) V~/50Hz
10
Maximum: 1 Mpa
Minimum : 0.1 Mpa
2200
7
1000-1200-1400
15
845 x 597 x 527
EN -22-
CHAPTER -3: INSTALLATION OF THE MACHINE REMOVING TRANSPORTATION SAFETY SCREWS
Before operating the washing machine, remove the 4 transportation screws and rubber spacers from the back of the machine. If the screws are not removed, it may cause heavy vibration, noise and product malfunction, (voiding the guarantee).
For this reason, transportation safety screws shall be loosened by being rotated in counter-clockwise using an appropriate wrench.
X4
X4
EN -23-
CHAPTER -3: INSTALLATION OF THE MACHINE (REMOVING TRANSPORTATION SAFETY SCREWS)
Transportation screws |
|
shall be removed by pull- |
|
ing out. |
X4 |
Fit the plastic transportation screw taps delivered in accessories bag to the palces where transportation screws have been removed.
The transportation safety screws should be stored to be used in case of transportation.
NOTE: You should absolutely remove the transportation screws of your machine before the first usage.
Faults occurring in the machines operated with transportation screw fitted shall be out of scope of warranty.
EN -24-
CHAPTER -3: INSTALLATION OF THE MACHINE
(Adjusting Adjustable Stays)
•Do not install your machine on a carpet or such grounds that would prevent the ventilation of its base.
•To ensure silent and vibration-free operation of your machine, it should be deployed on a non-sliding and firm ground.
•You can adjust the balance of your machine through the stays.
•Loosen the plastic adjustment nut.
EN -25-
CHAPTER -3: INSTALLATION OF THE MACHINE (ADJUSTING ADJUSTABLE STAYS)
•Adjust the stays upward and downward by rotating them.
•After maintaining the balance, compress the plastic adjustment nut upward again.
X4
EN -26-
CHAPTER -3: INSTALLATION OF THE MACHINE (ADJUSTING ADJUSTABLE STAYS)
•Never put cardboard, wood or suchlike materials under your machine if you are intending to stabilize the distortions on the ground.
•When cleaning the ground, on which your machine rests, be careful not to disorder stays stabilization.
EN -27-
CHAPTER -3: INSTALLATION OF THE MACHINE (ELECTRICAL CONNECTION)
• Your washing machine is set to 220-240V and 50Hz.
• The mains cord of your washing machine is equipped with a specific earthed plug. This plug should always be inserted to a earthed socket of 10 amps.
• The current value of the fuse should be 10 amps.
Fuse current value of the power line connected to this plug should also be 10 amperes.
•If you don’t have such a receptacle and fuse confirming with this, please have it done by a qualified electrician.
•We do not take the responsibility of the damages that occur due to ungrounded usage.
NOTE: Operating your machine under low voltage will cause the life cycle of your machine to be reduced and its performance to be restricted.
EN -28-
CHAPTER -3: INSTALLATION OF THE MACHINE (WATER INLET HOSE CONNECTION)
•Your machine may have either a single inlet (cold) or double water inlets (cold/hot) based on its specifications.
White-capped hose should be connected to cold water inlet and red-capped hose to hot water inlet (applicable for machines with double water inlets).
•To eliminate water leakages in points of contact, 1 or 2 nuts are provided in the hose package (applicable for machines with double water inlets).
Fit these nuts to the ends of new water inlet hoses on the side of faucet.
•Mount new water inlet hoses to a ¾ ˝, threaded faucet.
•Connect the white-elbow end of the water inlet hoses to the white-filtered water inlet valve on the rear side of the machine and the red-elbow end to red-filtered one (applicable for machines with double water inlets).
Tighten plastic parts of the junctions using your hand.
In uncertain conditions, have the connection works be done by a qualified plumber.
•Flow of water with pressure of 0,1-1 Mpa will allow your machine to operate more efficiently.) (0,1 Mpa pressure means that more than 8 litres of water will flow through a fully-tapped faucet per one minute.)
•Ensure that points of contact do not leak by tapping the faucet completely after carrying making the connections.
3/4”
10 mm
EN -29-
CHAPTER -3: INSTALLATION OF THE MACHINE (WATER INLET HOSE CONNECTION)
•Ensure that the new water inlet hoses are not bent, broken, crushed and resized.
•If your machine has double hot water inlets, the temperature of hot water inlet should be maximum 70°C.
Note: Use only the new water inlet hose coming with your machine while making water inlet connections of your machine. Never use old, used or damaged water inlet hoses.
EN -30-
Loading...