Loading...
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY THIS MANUAL IS PRINTED ON RECYCLED PAPER
B y S H E R W O O D I N D U S T R I E S
E G - 4 0 F i r e p l a c e I n s e r t V e n t e d R o o m
H e a t e r
O W N E R S M A N U A L
Installation And Operating Instructions For Model:-
WHAT TO DO IF YOU SMELL GAS
•Open windows/Extinguish any open flame
•Do not try to light any appliance.
•Do not touch any electrical switch; do not use any phone in your building.
•Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
•If you cannot reach your gas supplier, call the fire department.
EG-40 FPI. BV.
WARNING
If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A qualified installer, service agency or the gas supplier must perform installation and service.
Do not store or use gasoline or other Flammable vapors and liquids in the vicinity of this or any other appliance.
PLEASE KEEP THESE OPERATING INSTRUCTIONS FOR FUTURE REFERENCE.
SAFETY PRECAUTIONS
FOR SAFE INSTALLATION AND OPERATION OF YOUR "ENVIROGAS" ROOM HEATER, PLEASE, CAREFULLY READ THE FOLLOWING INFORMATION:
•All "ENVIROGAS" gas-fired appliances must be installed in accordance with these instructions. Carefully read all the instructions in this manual first. Consult the building authority having jurisdiction to determine the need for a permit prior to commencing the installation.
•NOTE Failure to follow these instructions could cause a malfunction of the fireplace that could result in death, serious bodily injury, and/or property damage.
•Failure to follow these instructions may also void your fire insurance and/or warranty.
installation code in Canada or the National Fuel Gas Code ANSI Z223.1.2 in the USA.
•To prevent injury, do not allow anyone who is unfamiliar with the operation to use the stove.
•Always keep the area around these appliances clear of combustible material, gasoline or other flammable vapors and liquids.
•These appliances should not be used as a drying rack for clothing or for hanging Christmas stockings or decorations.
GENERAL
•Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartment, burners and circulating air passageways of the appliance be kept clean.
•Due to high temperatures the appliance should be located out of high traffic areas and away from furniture and draperies.
Children and adults should be alerted to hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.
•Young children should be carefully supervised when they are in the same room as the appliance.
•Clothing or other flammable material should not be placed on or near the appliance.
FOR YOUR SAFETY
•A qualified installer, service agency or the gas supplier must perform installation and service.
•This installation must conform with local codes or, in the absence of local codes with the current CAN/CGA -B- 149
•Due to the paint curing on the stove a faint odor and slight smoking will likely be noticed when the stove is first used. Open a window until the slight smoking stops.
Always connect this gas stove to a chimney and vent to the outside of the building envelope. Never vent to another room or inside a building. Make sure you use the vent pipe that is specified. Make sure that the vent is properly sized and is of adequate height to provide the proper draft. Inspect the venting system annually for blockage and any signs of deterioration.
•Do not operate with cracked or broken
glass. Under no circumstances should this appliance be modified. Parts that have to be removed for servicing must be replaced prior to operating this appliance. Only parts supplied by ENVIROGAS should be used in this appliance and replacements should only be performed by a licensed or qualified service person.
•Never use solid fuels such as wood, paper, cardboard, coal, or any other flammable liquids etc., in this appliance.
•Do not use this heater if any part has been under water. Immediately call a qualified service technician to inspect the heater and to replace any part of the control system and any gas control that has been under water.
•Do not abuse glass by striking or slamming door shut.
2
|
TABLE OF CONTENTS |
|
1 |
Code Approvals ..................................................................................................... |
3 |
2 |
Specifications......................................................................................................... |
3 |
3 |
Assembly and Installation Instruction ................................................................... |
4 |
4 Deciding Where to Locate Your Stove………………………………………………..5 |
||
5 |
Venting................................................................................................................... |
7 |
6 |
Installation of Log Sets and Embers...................................................................... |
8 |
7 |
Operating Instructions............................................................................................ |
9 |
8 |
Routine Maintenance............................................................................................ |
10 |
9 |
Trouble Shooting................................................................................................... |
11 |
10 |
Gas Line Connection ............................................................................................ |
12 |
11 |
Electrical Requirements........................................................................................ |
13 |
13 |
Parts and Accessories .......................................................................................... |
14 |
|
Air Shutter Adjustment.......................................................................................... |
15 |
14 |
Warranty ............................................................................................................... |
16 |
15 |
Installation Data Sheet.......................................................................................... |
17 |
1. CODE APPROVALS
Canadian Standards Association has tested these appliances, and found them to comply with the established standards for GAS FIRED VENTED ROOM HEATER in CANADA and the USA as follows:
ENVIROGAS EG-40 VENTED ROOM HEATER (EG-40 FPI BV Nat & LPG.)
TESTED TO: ANSI Z21.11.1-1991,Z21.11.1A.-1193 CAN 1-2.1M 86.
2. SPECIFICATIONS
ENVIROGAS 40 (FIREPLACE INSERT) VENTED ROOM HEATER
Vented Type, designated by the suffix BV, this unit must be vented through a conventional chimney with a certified chimney liner kit.
•Has been certified for use with either natural or propane gases. (See rating label.)
•Is not for use with solid fuels.
•Is approved for bedroom or bedsitting room.
•Must be installed on a non-combustible surface.
•Must be installed in accordance with local codes.
If none exist use current installation code CAN/CGA B149 in Canada or ANSI Z223.1/NFPA 54 in the USA.
•Must be properly connected to a venting system.
WARNING; for installation only in a solid fuel burning fireplace with a working flue and constructed of non-combustible material.
FOR INSTALLATIONS ABOVE 2000 FEET
•In Canada, these appliances are certified for altitudes of 0-2,000 feet and must be derated by 10% for installation at elevations between 2,000 and 4,500 feet.
•In the USA, this appliance is certified for elevations up to 2,000 feet. For elevations above 2,000 feet, input should be reduced 4% for every 1,000 feet above sea level.
The efficiency rating of this appliance is a product thermal efficiency rating determined under continuous operating conditions and was determined independently of any installed system.
3
3. ASSEMBLY AND INSTALLATION INSTRUCTIONS
PREPARATION FOR INSTALLATION
•Remove the packaging from the appliance, surround panels and log set, check to make sure there is no damage. Carefully check the glass door. Do not use the unit if it is damaged. In the event damage is found please report it to both the courier and your dealer as soon as possible.
•Carefully clean the fireplace and flue before installing the stove. Failure to do so may result in fumes or dirt being blown into the room and may cause a fire leading to death or serious injury.
ASSEMBLING AND INSTALLING YOUR ENVIROGAS APPLIANCE
1.Remove the two wood screws that attach the stove to its pallet.
2.Remove the vent collar plate from the top of the stove by unscrewing the T20 Torx screw, located on the center top of the stove and slide back. Properly secure the vent collar plate to the approved flexible vent pipe liner previously installed in the chimney, secure properly
3.Place the unit part way into the fireplace. Connect the fireplace insert's flexible gas line to the household gas supply using locally approved methods.
4.Place the electric cable so it can be connected to the power supply. Push the unit into its final position in the fireplace insuring that it is stable and level. Using the leveling legs provided with the surround panel set.
5.Reinstall the vent collar plate to the stove by sliding it along the draft hood and securing with the screw.
6.Assemble the surround panel set following the instruction sheet provided.
7.Remove the hinged side flaps from the panel mounting brackets on each side of the unit.
8.Loosen the 1/4" bolts holding the stove top (7/16" wrench). Pull top forward, lift up and remove.
9.Connect surround panel wire harness to the stove wire harness following the wiring diagram on PAGE 13.
10.Place the assembled surround around the stove, in front of the surround mounting brackets Make sure the top surround panel sits flat on the stove.
11.Re-attach the hinged side flaps by sandwiching the surround panels between the mounting brackets and the hinged side flaps. Secure with screws.
12.Reinstall the top by inserting the bolts into the key-holes, push the top back aligning the holes in the top with the screws in the panel, tighten the bolts, re-attach the top grill bar.
13.Be sure to maintain adequate clearances around air openings, do not block.
14.Wipe down all gold surfaces with a soft rag to remove fingerprints, they may become etched when the unit is heated up.
4
4.DECIDING WHERE TO LOCATE YOUR STOVE
DIMENSIONS:
UNIT DIMENSIONS: |
|
A. Mantle pillar to stove 10"/ 25 cm |
|||
Front Width: |
26"/66 cm |
|
B. Stove to 8" wide mantle 12"/ 31 cm |
||
Height Front: |
22"/56 cm |
|
Stove must sit on a non-combustible |
||
Height Back: |
19-3/4"/50 cm |
|
surface, the width and depth of the insert |
||
Total Depth: |
22-1/2"/57 cm |
|
Maintain sufficient clearances |
|
|
Shipping Weight: |
256 lb./116 kg |
|
for operation, service and maintenance |
||
|
|
|
|
OTHER DIMENSIONS |
|
|
|
|
|
A. Depth of unit into fireplace |
17"/ 43 cm |
SURROUND DIMENSIONS: |
|
B. Depth of unit out of fireplace 9 3/4"/ 25 cm |
|||
STANDARD |
40" /101 cm |
|
C. Width of side panel |
7"/ 18 cm |
|
|
28-1/2" /71 cm |
|
D. Stove top to surround top |
6 3/4"/ 17 cm |
|
OVERSIZE |
46” / 116.8 cm |
|
E. Minimum firebox size W 36"x H 24"x D24" |
||
|
33” / 83.2 cm |
|
(W92 x H61 x D61) cm |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8”
40”
22 1/2”
12”
28 1/2”
19 3/4”
26”
5
VENT TERMINAL CLEARANCES
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
A= Clearance above grade, verandah, porch, deck, or |
H= *Not to be installed above a meter/regulator |
||||
|
[balcony (*12 inches (30 cm) minimum] |
assembly within 3 feet (90 cm) horizontally |
|||
B= Clearance to window or door that may be opened |
from the center-line of the regulator |
||||
|
[*12 inches (30 cm) minimum] |
I= Clearance to service regulator vent outlet |
|||
C= Clearance to permanently closed window |
[*6 feet |
(1.8m) minimum] |
|||
|
[minimum 12 inches (30 cm) recommended to |
J= Clearance to non-mechanical air supply inlet to |
|||
|
prevent condensation on window] |
building or the combustion air inlet to any |
|||
D= Vertical clearance to ventilated soffit located above |
other appliance [12 inches (30 cm) minimum] |
||||
the terminal within a horizontal |
distance of 2 feet (60 |
K= Clearance to a mechanical air supply inlet |
|||
cm) from the center-line |
of the terminal 24 |
[*6 feet (1.8m) minimum] |
|||
inches ( 60 cm) minimum |
|
L= *** Clearance above paved side-walk or paved |
|||
E= Clearance to unventilated soffit |
driveway located on public property |
||||
|
[18 inches (45 cm) minimum] |
[*7 feet |
(2.1m) minimum] |
||
F= Clearance to outside corner [12 inches minimum] |
M= Clearance under verandah, porch, deck, or balcony |
||||
G= Clearance to inside corner [`12 inches minimum] |
[*24 inches (60 cm) minimum **] |
||||
***A vent shall not terminate directly above a sidewalk or paved driveway, which is located between two singlefamily dwellings and serves both dwellings.
**Only permitted if verandah, porch, deck, or balcony, is fully open on a minimum of 2 sides beneath the floor
•As specified in CGA B149 Installation Codes (1991) Note: Local Codes or Regulations may require different clearances
NOTE: THIS HEATER MUST BE PROPERLY CONNECTED TO A VENTING SYSTEM. THIS HEATER IS EQUIPPED WITH A VENT SAFETY SHUTOFF SYSTEM DESIGNED TO PROTECT AGAINST IMPROPER VENTING OF COMBUSTION PRODUCTS.
THIS SAFETY SWITCH IS LOCATED ON THE REAR OF THE APPLIANCE CLOSE TO THE DRAFT HOOD
RELIEF OPENING.
IF THE SWITCH TRIPS MORE THAN ONCE THE CHIMNEY SHOULD BE INSPECTED BY A QUALIFIED SERVICE TECHNICIAN FOR POSSIBLE BLOCKAGE OR SEVERE DOWN DRAFT CONDITIONS
This stove can be vented with aluminum or stainless steel flex vent and/or certified 4" Type B Gas Vent. The flue collar of the appliance will fit inside of a standard 4” vent and may be fastened directly to the vent.
Check periodically that the vent is unrestricted and an adequate draft is present when the unit is in operation.
WARNING: Operation of this heater when not connected to a properly installed and maintained venting system or tampering with the vent safety shutoff system can result in carbon monoxide (CO) poisoning and possible death.
6
Loading...