Empire Comfort Systems VFSM-24-3, VFSM-18-3, VFSM -30-3, VFSV-16-3, VFSV-30-3 User Manual

...
0 (0)
Empire Comfort Systems VFSM-24-3, VFSM-18-3, VFSM -30-3, VFSV-16-3, VFSV-30-3 User Manual

Empire Comfort Systems, Inc.

INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL

Vented/Vent-Free Burner

This appliance may be installed in an aftermarket permanentlylocated,manufactured(mobile)home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

WARNINGS

If the information in this manual is not followed exactly,afireorexplosionmayresultcausingproperty damage, personal injury or loss of life.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediately call your gas supplier from neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

UNVENTED GAS LOG HEATER OR VENTED DECORATIVE APPLIANCE

MODELS

VFSR-16-3

VFSV-16-3

VFSM-18-3

VFSR-18-3

VFSV-18-3

VFSR-24-3

VFSV-24-3

VFSM-24-3

VFSR-30-3

VFSV-30-3

VFSM -30-3

EFFECTIVE DATE

JULY 2005

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Thisisanunventedgas-firedheater.Itusesair(oxy- gen)fromtheroominwhichitisinstalled.Provisions foradequatecombustionandventilationairmustbe provided. Refer to page 7.

WARNING:Ifnotinstalled,operatedandmaintained in accordance with the manufacturer's instructions, this product could expose you to substances in fuel or from fuel combustion which can cause death or serious illness.

WATERVAPOR:ABY-PRODUCTOFUNVENTED ROOM HEATERS

Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one

(1) ounce (30ml) of water for every 1,000 BTU's (.3KW's) of gas input per hour. Refer to page 6.

18954-0-0705

Page 1

TABLE OF CONTENTS

 

Section

Page

Important Safety Information .........................................................................................................................

3

Safety Information for Users of LP Gas..........................................................................................................

4

Introduction .....................................................................................................................................................

5

General Information ........................................................................................................................................

6

Water Vapor: By Product of Unvented Room Heaters ....................................................................................

6

Provisions for Adequate Combustion and Ventilation Air...............................................................................

7

Clearances....................................................................................................................................................

7-8

Combustible Material ......................................................................................................................................

9

Fireplace Preparation.......................................................................................................................................

9

Installing as a Vented Appliance....................................................................................................................

10

Before Fully Installing the Appliance............................................................................................................

10

Gas Supply.....................................................................................................................................................

11

Placement of Glowing Embers and Lava Rock.............................................................................................

12

Operation Instructions/Flame Appearance ....................................................................................................

12

VFSR-(16, 18, 24, 30) Lighting Instructions ................................................................................................

13

VFSV-(16, 18, 24, 30) Lighting Instructions ................................................................................................

14

VFSM-(18, 24, 30) Lighting Instructions .....................................................................................................

15

Pilot Flame Characteristics......................................................................................................................

16-17

Cleaning and Servicing..................................................................................................................................

17

Wiring ...........................................................................................................................................................

18

Troubleshooting.............................................................................................................................................

19

Parts List........................................................................................................................................................

20

Parts View......................................................................................................................................................

21

How to Order Repair Parts ............................................................................................................................

21

Service Notes...........................................................................................................................................

22-23

Page 2

18954-0-0705

IMPORTANT SAFETY INFORMATION

An unvented room heater having an input rating of more than 6,000 Btu per hour shall not be installed in a bathroom

An unvented room heater having an input rating of more than 10,000 Btu per hour shall not be installed in a bedroom or bathroom.

Never burn solid fuels in a fireplace where a gas log set is installed.

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

Do not place clothing or other flammable material on or near the appliance.

Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition.

Young children should be carefully supervised when they are in the same room as the appliance.

This unit complies withANSI Z21.11.2 Unvented Heaters and it also complies withANSI Z21.60 DecorativeVentedAppliances for Solid Fuel Burning Fireplaces. State or local codes may only allow operation of this appliance in a vented configuration. Check your state or local codes.

Correct installation of logs, proper location of the heater and annual cleaning are necessary to avoid potential problems with sooting. Sooting, resulting from improper installation or operation, can settle on surfaces outside the fireplace.

Avoid any drafts that could alter burner flame patterns. Do not allow fans to blow directly into the fireplace. Do not place a blower inside burn box area of firebox. Ceiling fans may create drafts that alter burner flame patterns. Sooting and improper burning will occur as a result of drafts.

WARNING:Donotallowfanstoblowdirectlyintothefireplace. Avoid any drafts that alter burner flame patterns.

WARNING: Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this heater.

Periodic examination and cleaning of the venting system of the solid-fuel burning fireplace, including frequency of such examination and cleaning, by a qualified agency.

The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA54.

NOTE: Installation and repair should be done by a qualified service person. The appliance should be inspected before use andatleastannuallybyaqualifiedserviceperson.Morefrequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that the control compartment, burners and circulating air passageways of the appliance be kept clean.

Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance. Provide adequate combustion and ventilation air.

The flow of combustion and ventilation air MUST NOT be obstructed.

Provide adequate clearances around air openings into the combustion chamber and adequate accessibility clearance for servicing and proper operation. NEVER obstruct the front opening of the appliance.

An unvented room heater intended for installation in a solid-fuel burning fireplace shall comply with the following instructions.

Afireplacescreenmustbeinplacewhentheapplianceisoperating and,unlessotherprovisionsforcombustionairareprovided,the screen shall have an opening(s) for introduction of combustion air.

Solid-fuels shall not be burned in a masonry or UL127 factorybuilt fireplace in which an unvented room heater is installed.

Any glass doors shall be fully opened when the appliance is in operation.

Any outside air ducts and/or ash dumps in the fireplace shall be permanently closed at time of appliance installation.

WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.

WARNING: Before installing in a solid-fuel burning fireplace, the chimney flue and firebox must be cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner.

WARNING

 

CARBON MONOXIDE POISONING MAY LEAD TO

When used without adequate combustion and ventilation air,

DEATH.

heater may give off CARBON MONOXIDE, an odorless,

Early signs of carbon monoxide poisoning resemble the flu,

poisonous gas.

with headache, dizziness and/or nausea. If you have these

 

 

signs, heater may not be working properly. Get fresh air at

Donotinstallheateruntilallnecessaryprovisionsaremadefor

 

 

once! Have heater serviced.

combustionandventilationair.Consultthewritteninstructions

 

 

Some people – pregnant women, persons with heart or lung

provided with the heater for information concerning

 

 

disease, anemia, those under the influence of alcohol, those at

combustion and ventilation air. In the absence of instructions,

 

 

high altitudes – are more affected by carbon monoxide than

refer to the National Fuel Gas Code, ANSI Z223.1, Section

 

 

others.

5.3 or applicable local codes.

 

 

The pilot light safety system senses the depletion of oxygen

This heater is equipped with a PILOT LIGHT SAFETY

at its location. If this heater is installed in a structure having a

SYSTEM designed to turn off the heater if not enough fresh air

high vertical dimension, the possibility exists that the oxygen

is available.

supply at the higher levels will be less than that at the heater. In

DO NOT TAMPER WITH PILOT LIGHT SAFETY

 

 

this type of application, a fan to circulate the structure air will

SYSTEM!

 

minimize this effect. The use of this fan will also improve the

If heater shuts off, do not relight until you provide fresh air.

 

comfort level in the structure. When a fan is used to circulate

If heater keeps shutting off, have it serviced. Keep burner and

air, it should be located so that the air flow is not directed at

control compartment clean.

the burner.

18954-0-0705

Page 3

SAFETY INFORMATION FOR USERS OF LP-GAS

Propane (LP-Gas) is a flammable gas which can cause fires and explosions.Initsnaturalstate,propaneisodorlessandcolorless. You may not know all the following safety precautions which can protect both you and your family from an accident. Read them carefully now, then review them point by point with the

members of your household. Someday when there may not be a minute to lose, everyone's safety will depend on knowing exactly what to do. If, after reading the following information, you feel you still need more information, please contact your gas supplier.

LP-GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas. That's your signal to go into immediate action!

Do not operate electric switches, light matches, use your phone. Do not do anything that could ignite the gas.

Get everyone out of the building, vehicle, trailer, or area. Do that IMMEDIATELY.

Close all gas tank or cylinder supply valves.

LP-Gas is heavier than air and may settle in low areas such as basements. When you have reason to suspect a gas leak, keep out of basements and other low areas. Stay out until firefighters declare them to be safe.

Useyourneighbor'sphoneandcallatrainedLP-Gasservice person and the fire department. Even though you may not continue to smell gas, do not turn on the gas again. Do not re-enter the building, vehicle, trailer, or area.

Finally,lettheservicemanandfirefighterscheckforescaped gas. Have them air out the area before you return. Properly trained LP-Gas service people should repair the leak, then check and relight the gas appliance for you.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell the odor of the chemical put into the gas. You must find out if you can smell the odorant in propane. Smoking can decrease your ability to smell. Being around an odor for a time can affect your sensitivity or ability to detect that odor. Sometimes other odors in the area mask the gas odor. People may not smell the gas odor or their minds are on something else. Thinking about smelling a gas odor can make it easier to smell.

The odorant in LP-gas is colorless, and it can fade under some circumstances.For example,if thereis an underground leak,the movementofthegasthroughsoilcanfiltertheodorant.Odorants in LP-Gas also are subject to oxidation. This fading can occur if

there is rust inside the storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or into walls, masonry and other materials and fabrics in a room. That will take some of the odorant out of the gas, reducing its odor intensity.

LP-Gas may stratify in a closed area, and the odor intensity could vary at different levels. Since it is heavier than air, there may be more odor at lower levels. Always be sensitive to the slightest gas odor. If you detect any odor, treat it as a serious leak. Immediately go into action as instructed earlier.

SOME POINTS TO REMEMBER

Learn to recognize the odor of LP-gas. Your local LP-Gas Dealer can give you a "Scratch and Sniff" pamphlet. Use it to find out what the propane odor smells like. If you suspect that your LP-Gas has a weak or abnormal odor, call your LP-Gas Dealer.

If you are not qualified, do not light pilot lights, perform service, or make adjustments to appliances on the LP-Gas system. If you are qualified, consciously think about the odor of LP-Gas prior to and while lighting pilot lights or performing service or making adjustments.

Sometimes a basement or a closed-up house has a musty smell that can cover up the LP-Gas odor. Do not try to light pilot lights, perform service, or make adjustments in an area where the conditions are such that you may not detect the odor if there has been a leak of LP-Gas.

Odor fade, due to oxidation by rust or adsorption on walls of new cylinders and tanks, is possible. Therefore, people should be particularly alert and careful when new tanks or cylinders are placed in service. Odor fade can occur in new tanks, or reinstalled old tanks, if they are filled and allowed

to set too long before refilling. Cylinders and tanks which have been out of service for a time may develop internal rust which will cause odor fade. If such conditions are suspected to exist, a periodic sniff test of the gas is advisable. If you haveanyquestionaboutthegasodor,callyourLP-gasdealer. A periodic sniff test of the LP-gas is a good safety measure under any condition.

If, at any time, you do not smell the LP-Gas odorant and you thinkyoushould,assumeyouhavealeak.Thentakethesame immediateactionrecommendedabovefortheoccasionwhen you do detect the odorized LP-Gas.

If you experience a complete "gas out," (the container is under no vapor pressure), turn the tank valve off immediately. If the container valve is left on, the container may draw in some air through openings such as pilot light orifices. If this occurs, some new internal rusting could occur. If the valve is left open, then treat the container as a new tank. Always be sure your container is under vapor pressure by turning it off at the container before it goes completely empty or having it refilled before it is completely empty.

Page 4

18954-0-0705

INTRODUCTION

IMPORTANT: Read all instructions carefully before starting installation. Failure to follow these installation instructions may result in a possible fire hazard and will void the warranty.

Save this manual for future reference.

Please read this manual before installing and using the appliance. Instructions to Installer

1.Installer must leave instruction manual with owner after installation.

2.Installer must have owner fill out and mail warranty card supplied with unvented room heater/vented decorative appliance.

3.Installer should show owner how to start and operate unvented room heater/vented decorative appliance.

Always consult your local Building Department regarding regulations, codes or ordinances which apply to the installation of an unvented room heater/vented decorative appliance.

Thisappliancemaybeinstalledinanaftermarket*manufactured(mobile) home, where not prohibited by state or local codes.

*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

New Installation

VFSV Model - variable does not operate-ON is OFF/OFF is ON-wires into the back of receiver are reversed.

Solid-fuels shall not be burned in a fireplace where a vented decorative appliance is installed.

A vented decorative appliance must be installed only in a solid-fuel burningfireplacewithaworkingflueandconstructedofnon-combustible material.

Any alteration of the original design, installed other than as shown in these instructions or use with a type of gas not shown on the rating plate is the responsibility of the person and company making the change.

Important

All correspondence should refer to complete Model Number, Serial Number and type of gas.

Attention: During initial use of log you will detect an odor as the log is cured.

Notice:Duringinitialfiringofthisunit,itspaintwillbakeout,andsmoke will occur. To prevent triggering of smoke alarms, ventilate the room in which the unit is installed.

WARNING: This appliance is for installation only in a solid-fuel burning masonry or UL 127 factory-built fireplace or in a listed ventless firebox enclosure. It has been design certified for these installations.Exception:DONOTinstallthisapplianceinafactorybuiltfireplacethatincludesinstructionsstatingithasnotbeentested or should not be used with unvented gas logs.

WARNING: Any modification to this unvented gas heater or its controls can be dangerous. Improper installation or use of the heater can cause serious injury or death from fire, burns, explosion or carbon monoxide poisoning.

Well Head Gas Installations

Somenaturalgasutilitiesuse"wellhead"gas.ThismayaffecttheBtuoutput of the unit. Contact the gas company for the heating value. Contact the

manufacturer or your gas company before changing spud/orifice size.

ACCESSORIES

 

Description

Color

 

 

 

For use with VFSV, VFSM and VFSR models

 

 

 

 

EK-1

Embers Kit

 

 

 

 

ELH-1

Fireplace Hood for Vent-Free Logs

Black

 

 

 

ELH-2

Fireplace Hood for Vent-Free Logs

Brass

For use with VFSR models only

 

 

 

 

FRBC

Battery Operated Remote Control

 

 

 

 

FRBTC

Battery Operated Remote Control with Thermostat

 

FREC

Electric Remote Control

 

FWS

Wall Switch

 

GWSG-T

Wall Thermostat, Millivolt

 

TMV

Wall Thermostat, Millivolt - Reed Switch

 

PRODUCT SPECIFICATION

 

 

 

 

Natural Gas

 

 

Propane Gas

 

 

 

 

Variable

Millivolt

Manual

Variable

Millivolt

Manual

 

Regulator pressure setting

 

3.5" W.C.

3.5" W.C.

6.0"W.C.

10.0" W.C.

10.0" W.C.

10.0" W.C.

Gas inlet pressure

Max.

10.5" W.C.

10.5" W.C.

10.5"W.C.

13.0"W.C.

13.0" W.C.

13.0" W.C.

 

 

Min.

5.0" W.C.

5.0" W.C.

7.0" W.C.

11.0" W.C.

11.0" W.C.

11.0" W.C.

 

 

 

 

 

 

 

 

 

 

 

 

BTUH

BTUH

BTUH

Model

Gas

Valve Type

Max. Rate

Med. Rate

Min. Rate

VFSV-16

Natural

Variable

25,000

17,500

VFSV-16

Propane

Variable

22,500

15,750

VFSR-16

Natural

Millivolt

25,000

17,500

VFSR-16

Propane

Millivolt

22,500

15,750

VFSV-18

Natural

Variable

32,000

19,000

VFSV-18

Propane

Variable

32,000

19,000

VFSR-18

Natural

Millivolt

32,000

22,000

VFSR-18

Propane

Millivolt

32,000

22,000

VFSM-18

Natural

Manual

32,000

27,000

22,000

VFSM-18

Propane

Manual

32,000

27,000

22,000

VFSV-24

Natural

Variable

36,000

20,000

VFSV-24

Propane

Variable

36,000

20,000

VFSR-24

Natural

Millivolt

36,000

25,000

VFSR-24

Propane

Millivolt

36,000

25,000

VFSM-24

Natural

Manual

36,000

27,000

22,000

VFSM-24

Propane

Manual

36,000

27,000

22,000

VFSV-30

Natural

Variable

38,000

20,000

VFSV-30

Propane

Variable

38,000

20,000

VFSR-30

Natural

Millivolt

38,000

26,000

VFSR-30

Propane

Millivolt

38,000

26,000

VFSM-30

Natural

Manual

38,000

27,000

22,000

VFSM-30

Propane

Manual

38,000

27,000

22,000

18954-0-0705

Page 5

GENERAL INFORMATION

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided.

Keep room area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

Unvented gas heaters are a supplemental zone heater.They are not intended to be a primary heating appliance.Water vapor produced by an unvented heater can create moisture problems in a home when operated for extended periods of time.

During manufacturing, fabricating and shipping, various components of this appliance are treated with certain oils, films or bonding agents.These chemicals are not harmful but may produce annoyingsmokeandsmellsastheyareburnedoffduringtheinitial operation of the appliance; possibly causing headaches or eye or lung irritation. This is a normal and temporary occurrence.

The initial break-in operation should last 2-3 hours with the burner at the highest setting. Provide maximum ventilation by opening windowsordoorstoallowodorstodissipate.Anyodorsremaining after this initial break-in period will be slight and will disappear with continued use.

This appliance must not be used with glass doors in the closed position.This can lead to pilot outages and severe sooting outside the fireplace.

Do not use this room heater if any part has been under water. Immediately call a qualified service technician to inspect the room heater and replace any part of the control system and any gas control which has been under water.

WARNING:This appliance is equipped for (natural or propane) gas. Field conversion is not permitted.

Before you get started

Carefullyinspectthecontentsforshippingdamage.Ifanypartsare missing or damaged, immediately inform the dealer from whom you purchased the appliance. Do not attempt to install any part of the appliance unless you have all parts in good condition.

Make sure you have received all parts:

Check your packing list to verify that all listed parts have been received. You should have the following:

Gas log grate/burner assembly.

Two (2) masonry anchoring screws and two (2) 10 x 1/2" black sheet metal anchoring screws.

Plastic bag containing glowing embers (rock wool) for burner coverage.

Plastic bag containing lava rock.

Switch log assembly - VFSR models

Remote kit - VFSV models

Millivolt controlled heater designed to be operated with optional devices for ON/OFF functions.

Wall switch or thermostat with wire.

Hand held remote control with ON/OFF switch or thermostat.

Handle the gas log burner assembly by the grate and legs only. Do not pick the unit up by the burner.

Gloves are recommended when handling logs to prevent skin irritation. Logs are fragile - Handle with care.

Qualified Installing Agency

Installation and replacement of gas piping, gas utilization equipment or accessories and repair and servicing of equipment shall be performed only by a qualified agency. The term "qualified agency" means any individual, firm, corporation, or company that either in person or through a representative is engaged in and is responsible for (a) the installation, testing, or replacement of gas piping or (b) the connection, installation, testing, repair, or servicing of equipment; that is experienced in such work; that is familiar with all precautions required, and that has complied with all the requirements of the authority having jurisdiction.

State of Massachusetts: The installation must be made by a licensed plumber or gas fitter in the Commonwealth of Massachusetts.

Sellers of unvented propane or natural gas-fired supplemental room heaters shall provide to each purchaser a copy of 527 CMR-30 upon sale of the unit.

Theinstallationmustconformwithlocalcodesor,intheabsenceof local codes, with the National Fuel Gas Code, ANSI Z223.1.*

*Available from the American National Standards Institute, Inc. 11 West 42nd St., New York, N.Y. 10018.

High Altitudes: For altitudes/elevation above 2,000 feet ratings should be reduced at the rate of 4 percent for each 1,000 feet above sea level. Contact the manufacturer.

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS

Watervaporisaby-productofgascombustion.Anunventedroom heater produces approximately one (1) ounce (30ml) of water for every 1,000 BTU's (.3KW's) of gas input per hour.

Unvented room heaters must be used as supplemental heat (a room) rather than a primary heat source (an entire house). In most supplemental heat applications, the water vapor does not create a problem. In most applications, the water vapor enhances the low humidity atmosphere experienced during cold weather.

The following steps will help insure that water vapor does not become a problem.

1.Besuretheheaterissizedproperlyfortheapplication,including ample combustion air and circulation air.

2.If high humidity is experienced, a dehumidifier may be used to help lower the water vapor content of the air.

3.Donotuseanunventedroomheaterastheprimaryheatsource (an entire house).

Page 6

18954-0-0705

PROVISIONS FOR ADEQUATE COMBUSTION & VENTILATION AIR

This heater shall not be installed in a confined space unless provisions are provided for adequate combustion and ventilation air.

The National Fuel Gas Code defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8m3 per kw) of the aggregate input rating of all appliances installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed, through openings not furnished with doors, are considered a part of the unconfined space.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.

Unusually tight construction is defined as construction where:

a.Walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder with a rating of one perm or less with openings gasketed or sealed, and

b.Weatherstrippinghasbeenaddedonopenablewindowsanddoors, and

c.Caulking or sealants are applied to areas such as joints around windowanddoorframes,betweensoleplatesandfloors,between

wall-ceilingjoints,betweenwallpanels,atpenetrationsforplumb- ing, electrical, and gas lines, and at other openings.

If your home meets all of the three criteria above, you must provide additional fresh air.

Warning: If the area in which the heater may be operated is smaller than that defined as an unconfined space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the National Fuel Gas Code, ANSI Z223.1, Section 5.3. or applicable local codes.

Example of Large Room with 1/2 Wall divider. Figure 1

The following formula can be used to determine the maximum heater rating per the definition of unconfined space:

Btu/Hr = (L1 + L2)FT x (W)FT x (H)FT x 1000 50

If the area in which the heater may be operated is smaller than that defined as an unconfined space, provide adequate combustion and ventilation air by one of the methods described in the National Fuel Gas Code, ANSI Z223.1, Section 5.3.

Adhere to all codes, or in their absence, the latest edition of THE NATIONAL FUEL GAS CODE ANSI Z223.1 or NFPA54 which can be obtained from:

American National Standards Institute National Fire Protection Association, Inc.

11 West 42nd St.

BatterymarchPark

NewYork,NY10018

Quincy,MA02269

CLEARANCES

Minimum Dimensions For Solid Fuel Burning Fireplaces UL127 Factory Built Fireplaces (Figure 2)

Model

A

B

C

D

VFSV-16

18"

11 1/2"

24"

18"

VFSR-16

18"

11 1/2"

24"

18"

VFSV-18

17"

14"

28"

17"

VFSR-18

17"

14"

28"

17"

VFSM-18

21"

14"

32"

17"

VFSV-24

23"

14"

30"

18"

VFSR-24

23"

14"

30"

18"

VFSM-24

27"

14"

34"

18"

VFSV-30

26"

14"

34"

20"

VFSR-30

26"

14"

34"

20"

VFSM-30

30"

14"

38"

20"

The dimensions shown and defined in the fireplace manufacturer’s instructions are minimum clearances to maintain in installing this heater. Left and right clearances are determined when facing the front of the heater.

Glass Doors

Make sure that glass doors are open during all operations of the logset. The opening of the glass door frame should be the dimension used for the minimum front opening of the firebox.

Follow these instructions to ensure safe installation.

Failure to follow instructions exactly can create a fire hazard.

Figure 2

18954-0-0705

Page 7

CLEARANCES (continued)

Sidewall & Ceiling Clearances (Figure 3)

18", 24", 30"

Log

41"

16"

Log

36"

Figure 3

The sides of the fireplace opening must be 6" from any combustible wall. The ceiling must be at least 36" (for the 16" log) and 41" (for 18", 24"

and 30" logs) from the fireplace opening.

Mantel Clearances Without Hood (Figure 4)

You must have non-combustible materials above the fireplace opening. Non-combustible material must extend at least 12" above fireplace opening. With sheet metal, you must have non-combustible material behind it.

Heat resistant materials such as slate and marble must be at least 1/2" thick. Sheet metal should not be installed onto combustible material.

10" and less Mantel

HEAT RESISTANT MATERIAL

12" WITHOUT 28" HOOD

12"

HEATER IN FIREPLACE

OR FIREBOX

Non-Combustible

Requirements for

Material Distance

Safe Installation

12" or more

Non-combustible material.

Less than 12"

Non-combustiblematerialmustbeextendedto

 

at least 8" with the installation of the optional

 

fireplace hood. If you cannot extend non-

 

combustible material at least 8", you must

 

operate heater with flue damper open.

 

 

You must have non-combustible materials above the fireplace opening. Non-combustiblematerialmustextendatleast8"abovefireplaceopening. With sheet metal, you must have non-combustible material behind it.

Heat resistant materials such as slate and marble must be at least 1/2" thick. Sheet metal should not be installed onto combustible material.

Example:Amantel may project from the wall a maximum of 2" at a minimum of 13-1/2" above the opening, and a maximum of 6" at a minimum of 15" above the opening.

 

8" Mantel

 

 

 

6" Mantel

 

 

 

4" Mantel

 

 

HEAT RESISTANT

2" Mantel

 

 

 

 

 

MATERIAL

14.25"

16.0"

8" WITH HOOD

 

13.5"

15.0"

 

HOOD

HEATER IN

FIREPLACE

OR FIREBOX

Figure 5

If your installation does not meet the above minimum clearances, you must proceed to one of the following steps:

Operatetheheaterwiththefluedamperopen. Seepage10forInstalling as a Vented Appliance.

Raise the mantel to the proper height.

Remove the mantel.

Floor Clearance (Figure 6)

If installing heater at floor level, the minimum distance to combustibles is “0” inches.

If your installation does not meet the above clearances, you must proceed to one of the following steps:

• Use a hood

• Operate the heater with flue damper open. See page 10 for Installing as a Vented Appliance.

• Raise the mantel to the proper height.

• Remove the mantel.

Mantel Clearances with Hood (Figure 5)

Page 8

18954-0-0705

Loading...
+ 16 hidden pages