READ AND SAVE THESE INSTRUCTIONS
Ceiling Fan/Light
Remote Control & Wall Control
Owner's Manual
For Use With RCK55, RC188 or RC212 Receivers
Remote Control |
Remote Control |
Model Number: |
Model Number: |
SR600 |
SR650 |
Wall Control with Switch Covers
Model Number:
SW605
Part No. F40BP74170000 |
Form No. BP7417 |
!WARNING
Safety Instructions
WARNING: To avoid fire, shock, and serious personal injury, follow all instructions carefully.
1.Read your Owner's Manual carefully before installing the Remote Control or Wall Control. Retain Owner's Manual for future reference.
2.Before servicing or cleaning the ceiling fan, switch power off at service panel and lock service panel to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device such as a tag, to the service panel.
ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION
1.To avoid possible electrical shock, be sure electricity is turned off at the main fuse or circuit breaker box before wiring.
2.Make certain no bare wires are exposed outside the wire connectors.
3.All wiring must conform to National and Local Electrical Codes.
4.Follow the recommended instructions for the proper method of wiring your new Remote Control or Wall Control. If you feel you do not have enough electrical wiring knowledge or experience, have your Remote Control or Wall Control installed by a licensed electrician. Any electrical work not described in this manual should be performed by a licensed electrician.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label. You should record this data above and keep it in a safe place for future use.
2
General
Your Emerson Ceiling Fan/Light Control may be used with a SR600 or SR650 Remote Control or a SW605 Wall Control. The remote control or wall control is designed to control your ceiling fan speed, airflow direction, and light intensity.
Unpackaging
The carton with the SR650 Remote Control contains a storage bracket with two mounting screws.
The carton with the SW605 Wall Control contains three switch covers; ivory, white and almond color.
IMPORTANT
This Owner’s Manual is divided into three sections. The first section: SR600 REMOTE CONTROL PROCEDURES, describes how to install the two AAA alkaline batteries in the SR600 remote control transmitter and operating fuctions. The second section: SR650 REMOTE CONTROL PROCEDURES describes how to install the two CR2032 Lithium batteries in the SR650 remote control transmitter and operating fuctions. The third section describes how to install the SW605 Wall Control. These instructions must be performed prior to installation of the ceiling fan as described in the Ceiling Fan Owner’s Manual.
SR600 REMOTE
CONTROL PROCEDURES
General
Your Emerson Ceiling Fan/Light SR600 Remote Control consists of hand-held transmitter and a receiver which is mounted under the fan ceiling cover. The remote control is designed to separately control your ceiling fan speed and light intensity.
The remote control transmitter is powered by two AAA alkaline batteries (included). To prevent possible damage if the batteries should leak, be sure to remove the batteries when the control is not to be used for an extended period of time.
Code switches in the transmitter and receiver may be set in 32 different positions. If your fan and light go on and off without using your control, you may be getting interference from other remote units such as garage door openers, car alarms or security systems. To remedy this situations, simply change the combination code in your transmitter and receiver.
Preset Memory Feature
Your Emerson receiver is equipped with a preset memory feature. If the AC supply to the receiver is powered through a wall switch, when the switch is turned OFF, the control will remember the light intensity and fan speed. When the switch is turned back ON the light and fan will resume operation as they were prior to the switch being turned OFF.
3
Installation of Battery
1.Remove the battery cover by pressing firmly below the arrow and sliding the cover off the control (Figure 1).
2.Install two AAA alkaline batteries and reinstall the battery cover.
REMOTE CONTROL
LEVERS
|
|
|
|
|
ON |
1 |
2 |
3 |
4 |
5 |
I |
Setting Operating
Frequency of SR600
Remote Control
Your remote control has code switches which must be set in one of 32 possible code combinations. The five levers (numbered 1, 2, 3, 4, and 5) on the switches are factory-set in the ON (up) position. Change the switch settings as follows:
TWO AAA
BATTERIES
|
CODE |
|
|
SWITCHES |
|
BATTERY |
SR600 REMOTE |
|
COMPARTMENT |
||
CONTROL |
||
COVER |
||
|
Figure 1
Installation of Storage Bracket for SR600 Remote Control
A storage bracket is provided for holding your remote control when not in use. If you desire to use the bracket, install it on a wall that is away from excess heat or humidity (Figure 2).
TO INSTALL BRACKET TO WALL:
SLIDE THE COVER UP TO EXPOSE THE SCREW HOLES FOR INSTALLATION
COVER 
WALL
BRACKET
SCREW
HOLES (2)
Figure 2
1. Slide the five switch levers in the remote control to your choice of ON (up) or down positions. Use a ball-point pen or small screwdriver and slide the levers firmly up or down.
2. When power is restored, push and hold the fan OFF button ( 
) for 3 to 5 seconds to set the code in the receiver.
3. If airflow is desired in the opposite direction, press the (
) button on the wall control. The fan must be operating at any speed for the reverse button to function. The blades will turn in the opposite direction and reverse the airflow.
4. To set the desired fan speed, press the ( 
) button to decrease the speed and the ( 
) to increase the speed. The LED display will light up to indicate the new speed selected.
5. To turn the downlight on, press and release the ( 
) button. The light will turn on at the light intensity previously selected.
6. To turn the uplight on, press and release the ( 
) button. The light will
turn on at the light intensity previously selected.
7. To vary the intensity of the light, hold the DN or UP button down until the desired light intensity is reached, then release the button.
8. The sixth switch marked ON and I is for dimming control of lights: Set switch to ON to allow for dimming of the lights. Set switch to I for no dimming of the lights such as for fluorescent bulbs.
4
Loading...