Size:
3.03 Mb
Download

AppendixA: Serial Command Line Interface (CLI)

[<portlist>]: Port list (Default: All ports).

[enable|disable]: Enable/disable VLAN awareness (Default: Show awareness).

VLAN PVID: Syntax:

VLAN PVID [<portlist>] [<vid>|none]

Description: Set or show the port VLAN ID. Untagged frames received on the port will be classified to this VLAN ID. Frames classified to this VLAN ID will be sent untagged on the port.

[<portlist>]: Port list (Default: All ports).

[<vid>|none]: Port VLAN ID,1-4095(Default: Show PVID).

The ’none’ option can be used for trunk links.

VLAN Frame Type: Syntax:

VLAN Frame Type [<portlist>] [all|tagged]

Description: Set or show the accepted frame type for the port.

[<portlist>]: Port list (Default: All ports).

[all|tagged]: Accept all or only tagged (Default: Show frame type).

Aggregation/Trunking Commands

Aggregation Configuration:

Syntax:

Aggr Configuration

Description: Shows the aggregation groups and the aggregation mode.

Aggregation Add: Syntax:

Aggr Add <portlist>

Description: Add link aggregation group including ports.

<portlist>: Aggregation port list.

Aggregation Delete: Syntax:

Aggr Delete <portlist>

Description: Delete link aggregation group.

<portlist>: Port list. Aggregations including any of the ports will be deleted.

Aggregation Lookup: Syntax:

Aggr Lookup <portlist>

10007175-02

KAT4000 User’s Manual

A-13

 

 

 

AppendixA: Serial Command Line Interface (CLI)

Description: Lookup and display link aggregation group.

<portlist>: Port list. Aggregations including any of the ports will be shown.

Aggregation Mode: Syntax:

Aggr Mode [smac|dmac|xor]

Description: Set or show link aggregation traffic distribution mode.

[smac|dmac|xor]: Aggregation mode, SMAC, DMAC or XOR (Default: Show mode).

User Group Commands

User groups provide a way other than VLANs for making port groupings. With user groups it is possible to share a port between more user groups.

User Group Configuration:

Syntax:

User Group Configuration

Description: Show the user groups.

User Group Add: Syntax:

User Group Add <grouplist> [<portlist>]

Description: Add user group entry including the ports.

<grouplist>: User group ID list.

[<portlist>]: Port list (Default: All ports).

User Group Delete: Syntax:

User Group Delete <grouplist>

Description: Delete user group entry.

<grouplist>: User group ID list.

User Group Lookup: Syntax:

User Group Lookup <grouplist>

Description: Lookup user group entry and show port members.

<grouplist>: User group ID list.

QoS Commands

QoS Configuration: Syntax:

QoS Configuration [<portlist>]

A-14

KAT4000 User’s Manual

10007175-02

 

 

 

AppendixA: Serial Command Line Interface (CLI)

Description: Show the configured QoS mode, default class and DSCP mapping for the port.

[<portlist>]: Port list (Default: All ports).

QoS Mode: Syntax:

QoS Mode [<portlist>] [tag|port|diffserv]

Description: Set or show the QoS mode for the port.

[<portlist>]: Port list (Default: All ports).

[tag|port|diffserv]: Enable tag, port or IP differentiated services class of service for the port (Default: Show mode).

QoS Default: Syntax:

QoS Default [<portlist>] [<class>]

Description: Set or show the default class. In tag mode, the default class is used for untagged frames. In port mode, the default class is used as the port priority. In diffserv mode, the default class is used for non-IPframes.

[<portlist>]: Port list (Default: All ports).

[<class>]: Internal class of service (Default: Show class).

QoS Tagprio: Syntax:

QoS Tagprio [<portlist>] [<tagpriolist>] [<class>]

Description: Set or show the VLAN user priority mapping.

[<portlist>]: Port list (Default: All ports).

[<tagpriolist>]: VLAN user priority list,0-7(Default: All user priorities).

[<class>]: Internal class of service (Default: Show class).

QoS DiffServ: Syntax:

QoS DiffServ [<dscpno>] [<class>]

Description: Set or show the IP Differentiated Services mapping.

[<dscpno>]: IP DSCP list,0-63(Default: All DSCP values).

[<class>]: Internal class of service (Default: Show class).

QoS Userprio: Syntax:

QoS Userprio [<portlist>] [<tagprio>]

Description: Set or show the default VLAN user priority for received untagged frames.

[<portlist>]: Port list (Default: All ports).

10007175-02

KAT4000 User’s Manual

A-15

 

 

 

AppendixA: Serial Command Line Interface (CLI)

[<tagprio>]: VLAN tag user priority,0-7(Default: Show user priority).

QoS Shaper: Syntax:

QoS Shaper [<portlist>] [disable|<rate>]

Description: Set or show the shaper configuration.

[<portlist>]: Port list (Default: All ports).

[disable|<rate>]: Disable or set leaky bucket rate to a % of the port speed[0%-100%](Default: Show shaper rate).

QoS Policer: Syntax:

QoS Policer [<portlist>] [disable|<rate>]

Description: Set or show the policer configuration.

[<portlist>]: Port list (Default: All ports).

[disable|<rate>]: Disable or set leaky bucket rate to a % of the port speed[0%-100%](Default: Show policer rate).

Mirror Commands

Mirror Configuration: Syntax:

Mirror Configuration

Description: Show the mirror destination port and mirror mode for source ports.

Mirror Port: Syntax:

Mirror Port [<port>]

Description: Set or show the mirror destination port.

[<port>]: Mirror destination port (Default: Show mirror port).

Mirror Source: Syntax:

Mirror Source [<portlist>] [enable|disable]

Description: Set or show the source port mirror mode.

[<portlist>]: Source port list (Default: All ports).

[enable|disable]: Enable/disable mirroring of frames received on port (Default: Show mirror mode).

IP Commands

IP Configuration: Syntax:

A-16

KAT4000 User’s Manual

10007175-02

 

 

 

AppendixA: Serial Command Line Interface (CLI)

IP Configuration

Description: Show configured IP address, mask, gateway, VLAN ID and mode.

IP Setup: Syntax:

IP Setup [ipaddress> [<ipmask> [ipgateway>]]] [<vid>]

Description: Set or show IP configuration.

[<ipaddress>]: IP address (Default: Show IP configuration).

[<ipmask>]: IP subnet mask (Default: Subnet mask for address class).

[<ipgateway>]: Default IP gateway (Default: 0.0.0.0).

[<vid>]: VLAN ID,1-4095(Default: 1).

IP Mode: Syntax:

IP Mode [enable|disable]

Description: Activate or deactivate the IP configuration.

[enable|disable]: Enable/disable IP (Default: Show IP mode).

IP Arp: Syntax:

IP Arp

Description: Show the current content of the ARP table.

IP Ping: Syntax:

IP Ping <ip_addr> <number_of_passes>

Description: Send one ICMP ECHO packet to the IP address provided.

<ip_addr>: IP address to ping.

<number_of_passes>: Number of passes to ping (default: 1).

Debug Commands

Debug Read Register: Syntax:

Debug Read Register <block> [<subblock>] <address>

Description: Read register address.

<block>: Block identifier,0-7or0x0-0x7.

<subblock>: Sub block identifier,0-15or0x0-0xf.

<address>: Register address within block,0-255or0x00-0xff.

Debug Write Register: Syntax:

10007175-02

KAT4000 User’s Manual

A-17

 

 

 

AppendixA: Web Interface

Debug Write Register <block> <subblock> <address> <value>

Description: Write value to register address.

<block>: Block identifier,0-7or0x0-0x7.

<subblock>: Sub block identifier,0-15or0x0-0xf.

<address>: Register address within block,0-255or0x00-0xff.

<value>: Register value,0-4294967295or0x00000000-0xffffffff.

Debug PHY Read: Syntax:

Debug PHY Read <portlist> [<address>]

Description: Read PHY register for port.

<portlist>: Port list.

[<address>]: Register address,0-31or0x00-0x1f(Default: Read all registers).

Debug PHY Write: Syntax:

Debug PHY Write <portlist> <address> <value>

Description: Write value to PHY register for port.

<portlist>: Port list.

<address>: Register address,0-31or0x00-0x1f.

<value>: Register value to write,0-65535or0x0000-0xffff.

Debug SetRegs: Syntax:

Debug SetRegs [clear | <address>] [<port_no>] [<value>]

Description: Saves user manual defined switch registers to EEPROM to make values persistent, or clears/resets register values.

<address>: Register address, 0x1a or 0x1b.

<port_no>: Port number,0-25.

<value>: Register value to be stored.

WEB INTERFACE

From the web interface it is possible to:

Set port mode

Enable/disable flow control

Configure simple port-basedVLANs

A-18

KAT4000 User’s Manual

10007175-02

 

 

 

AppendixA: Web Interface

Configure aggregation groups

Configure QoS

Read and clear statistics counters

Restore system defaults

Note: The web interface uses port IDs versus the port number (i.e., the physical number of the port). Port numbers (“port #”=”portID”-1)are used when discussing Ethernet switch ports. For example, VLAN port ID 1 is the same as Ethernet switch port 0.

All operations are password protected. The password must be entered at login. The password is the same as that used in the command line interface.

IP mode is disabled in the factory default configuration. To use the web interface, first enable and configure the IP via the command line interface. Set the IP address, mask, and gateway according to your environment. Provided below is an example of how to enable the web interface via the command line interface (CLI):

>IP Setup 10.10.129.189 255.255.255.0 10.10.128.14.1 1

It is recommended that the port you plan to use to access the web interface be on its own dedicated VLAN. This is because in systems where two or more KAT4000 ports are connected to another Ethernet switch, it may not be possible to access the web interface through that Ethernet switch (depending on the switch and how it is configured).

Note: It is possible to configure the switch so the web interface is no longer accessible. For example, if configured to access the interface through VID 1 by default, always be sure that the port you are using to access the web interface remains on VLAN 1. If the web interface is no longer accessible, use the CLI to recover.

10007175-02

KAT4000 User’s Manual

A-19

 

 

 

AppendixA: Web Interface

Figure A-2: Web Interface for the Ethernet Core Switch

A-20

KAT4000 User’s Manual

10007175-02

 

 

 

Section B

AppendixB

SENSOR DATA RECORDS

This appendix details the KAT4000 IPMI Sensor Data Record (SDR) parameter values from “Sensors and Sensor Data Records” on page 9-40.Table B-1 is a summary of all the KAT4000 SDRs with a link to the detailed sensor record. All values are hexadecimal. Theno-CPUKAT4000 configuration includes all of the SDRs listed inTable B-1 with the exception of the following: BMC Watchdog, CPU Volt, and F/W (Firmware) Progress.

Table B-1: IPMI Sensor Data Record

 

 

Record ID

 

Sensor Name:

(hex):

Table Information:

KAT4000

0000

Table B-2on pageB-2

 

 

 

Hot Swap

0001

Table B-3on pageB-2

 

 

 

IPMB Physical

0002

Table B-4on pageB-4

 

 

 

BMC Watchdog

0003

Table B-5on pageB-5

 

 

 

+3.3 Volt

0004

Table B-6on pageB-7

 

 

 

+2.5 Volt

0005

Table B-7on pageB-9

 

 

 

+1.8 Volt

0006

Table B-8on pageB-11

 

 

 

+1.2 Volt

0007

Table B-9on pageB-13

 

 

 

+1.0 Volt

0008

Table B-10on pageB-15

 

 

 

CPU Volt

0009

Table B-11on pageB-17

 

 

 

Inflow Temp

000a

Table B-12on pageB-19

 

 

 

Outflow Temp

000b

Table B-13on pageB-21

 

 

 

Version Change

000c

Table B-14on pageB-24

 

 

 

B1 Hot Swap

000d

Table B-15on pageB-25

 

 

 

B2 Hot Swap

000e

Table B-16on pageB-27

 

 

 

B3 Hot Swap

000f

Table B-17on pageB-28

 

 

 

B4 Hot Swap

0010

Table B-18on pageB-30

 

 

 

 

B1

+12V Current

0011

Table B-19on pageB-31

 

 

 

 

B1

+12V Volt

0012

Table B-20on pageB-33

 

 

 

 

B2

+12V Current

0013

Table B-21on pageB-35

 

 

 

 

B2

+12V Volt

0014

Table B-22on pageB-36

 

 

 

 

B3

+12V Current

0015

Table B-23on pageB-38

 

 

 

 

B3

+12V Volt

0016

Table B-24on pageB-40

 

 

 

 

B4

+12V Current

0017

Table B-25on pageB-41

 

 

 

 

B4

+12V Volt

0018

Table B-26on pageB-43

 

 

 

-48VVolt

0019

Table B-27on pageB-45

 

 

 

-48VCurrent

001a

Table B-28on pageB-47

 

 

 

-48VSource A Volt

001b

Table B-29on pageB-48

 

 

 

-48VSource B Volt

001c

Table B-30on pageB-50

 

 

 

+3.3V Management

001d

Table B-31on pageB-52

 

 

 

 

10007175-02

KAT4000 User’s Manual

B-1

 

 

 

AppendixB: Sensor Data Records

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Record ID

 

 

 

 

 

 

Table Information:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sensor Name:

 

(hex):

 

 

 

 

 

 

(continued)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+12V Volt

 

001e

 

 

 

 

 

 

Table B-32on pageB-54

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+12V Current

 

001f

 

 

 

 

 

 

Table B-33on pageB-56

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F/W (Firmware) Progress

 

0020

 

 

 

 

 

 

 

 

 

Table B-34on pageB-58

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Table B-2: KAT4000 IPMC SDR Description

KAT4000:

 

Value:

 

Parameter:

 

Status:

Record ID

 

0000

 

 

 

 

 

 

 

 

 

SDR Version

 

51

 

 

 

 

 

 

 

 

 

Record Type

 

12

 

Controller

 

 

 

 

 

 

 

 

Record Length

 

12

 

 

 

 

 

 

 

 

 

Device Slave Address

 

00

 

 

 

 

 

 

 

 

 

Channel Number

 

00

 

 

 

 

 

 

 

 

 

Power State Notification /

 

cc

 

ACPI System Power State

 

notification required

Global Notification

 

 

 

 

 

 

 

 

 

ACPI Device Power State

 

notification required

 

 

 

 

 

 

 

 

 

 

 

Controller Status

 

dynamic

 

 

 

 

 

 

 

 

 

 

 

Controller Logs Init Agent Errors

 

yes

 

 

 

 

 

 

 

 

 

 

 

Log Init Agent Errors Accessing Controller

 

yes

 

 

 

 

 

 

 

 

 

 

 

Misc Controller Info

 

enable event message

 

 

 

 

 

 

generation from controller

 

 

 

 

 

 

 

Device Capabilities

 

29

 

IPMB Event Generator

 

 

 

 

 

 

 

 

 

 

 

 

FRU Inventory Device

 

 

 

 

 

 

 

 

 

 

 

 

Sensor Device

 

 

 

 

 

 

 

 

FRU Entity ID

 

a0

 

PICMG Front Board

 

 

 

 

 

 

 

 

FRU Entity Instance

 

60

 

 

 

 

 

 

 

 

 

OEM

 

00

 

 

 

 

 

 

 

 

 

Table B-3: Hot Swap SDR Description

 

 

KAT4000 Records:

 

Value:

 

Parameter:

 

Status:

 

 

 

Record ID

 

0001

 

 

 

 

 

 

 

 

 

SDR Version

 

51

 

 

 

 

 

 

 

 

 

Record Type

 

01

 

Full Sensor Record

 

 

 

 

 

 

 

 

Record Length

 

33

 

 

 

 

 

 

 

 

 

Sensor Owner ID

 

00

 

 

 

 

 

 

 

 

 

Sensor Owner LUN

 

00

 

 

 

 

 

 

 

 

 

Sensor Number

 

00

 

 

 

 

 

 

 

 

 

Entity ID

 

a0

 

()

 

 

 

 

 

 

 

 

Entity Instance

 

60

 

 

 

 

 

 

 

 

 

B-2

KAT4000 User’s Manual

10007175-02