Emerson CF705SAB03, CF804SBS01, CF704SPB03, CF704SORB03, CF705SAW03, CF804SWW01, CF705SORB03, CF805SORB01, CF805SBS01, CF804SORB01, CF705SPB03, CF805SWW01, CF705SWW03 User Manual

221.41 Kb
Loading...

READ AND SAVE THESE INSTRUCTIONS

Model No.

Model No.

CF705SAB03

CF704SAB03

CF805SBS01

CF804SBS01

CF705SAW03

CF704SAW03

CF805SORB01

CF804SORB01

CF705SORB03

CF704SORB03

CF805SWW01

CF804SWW01

CF705SPB03

CF704SPB03

Net Weight: 13.9 Lbs.

Net Weight: 11.2 Lbs.

CF705SWW03

CF704SWW03

 

 

Net Weight: 13.9 Lbs.

Net Weight: 11.2 Lbs.

 

 

DATE CODE:

The date code of this fan may be found on the box, stamped in ink on a white label.

You should record this data above and keep it in a safe place for future use.

SNUGGER Ceiling Fan

Owner's Manual

Part No. F40BP70800008

Form No. BP7080-8

 

 

!WARNING

WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.

Safety Instructions

1.Read your owner’s manual carefully and keep it for future reference.

2.Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel.

3.Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before servicing.

4.Do not put anything into the fan blades while they are turning.

5.Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions for Installation

1.To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.

2.All wiring must be in accordance with the National Electrical Codes “ANSI/NFPA 70-1999” and Local Electrical Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician.

3.The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 pounds. Use only U.L. outlet boxes marked as “Acceptable for Fan Support”, and use the mounting screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

4.The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.

5.Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not know enough about electrical wiring, have your fan installed by a licensed electrician.

WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not specifically approved for this fan.

WARNING: This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal injury or property damage.

WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One Phillips head screwdriver

One 1/4" blade screwdriver

One stepladder

One wire stripper

Three wire connectors (supplied)

Materials

Wiring electrical box and box connectors must be of type required by local code. The minimum wire would be a 3-conductor (2-wire with ground) of size shown at right.

Installed Wire Length

Wire Size A.W.G.

Up to 50 ft.

 

14

50 - 100 ft.

12

!WARNING

Before assembling your ceiling fan, refer to section on proper method of wiring your fan (page 5). If you feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician.

2

Unpacking Instructions

For your convenience, check-off boxes are provide next to each step. As each step is completed, place a check mark in the box. This will insure that all steps have been completed and will be helpful in finding your place should you be interrupted.

!WARNING

Do not install or use fan if any part is damaged or missing. Call Toll-Free:

1-800-654-3545

!WARNING

This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal injury or property damage.

1.Check to see that you have received the following parts:

NOTE: If you are uncertain of part description, refer to exploded view illustration.

a.Fan housing

b.Mounting plate

c.Fan motor assembly

d.Five fan blades

e.Five blade flanges with captive screws

f.One loose parts bag containing:

1.Sixteen M5 x 6mm Phillips washer head screws

2.One M5 x 13mm Phillips pan head screw with lockwasher

3.Four M5 x 10mm Phillips pan head screws with internal tooth washers

4.Three 1/4” hex locknuts

5.One wood pendant

6.One chain coupling

7.Three wire connectors

NOTE: Place the parts from the loose parts bag in a small container to keep them from being lost. If any parts are missing, contact your local retailer or catalog outlet for replacement before proceeding.

2. Remove the fan assembly from the protective plastic bag. Place the fan assembly into the upper foam pad with the lead wires up.

 

FAN

 

BLADES

 

UPPER

 

FOAM PAD

 

MOUNTING

 

PLATE

 

FAN

 

HOUSING

 

BLADE FLANGES WITH

 

CAPTIVE SCREWS

LOWER

FAN

MOTOR

FOAM PAD

ASSEMBLY

CARTON

 

Electrical Requirements

Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit.

The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds.

!WARNING

To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked “Acceptable for Fan Support”, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture.

!WARNING

Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local Codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.

!WARNING

To avoid fire or shock, follow all wiring instructions carefully.

Any electrical work not described in these instructions should be done or approved by a licensed electrician.

3

+ 5 hidden pages