Emerson CF700OB07, CF700AB07, CF700PBW07, CF700AW07, CF700BS07 User Manual

...
0 (0)
Emerson CF700OB07, CF700AB07, CF700PBW07, CF700AW07, CF700BS07 User Manual

READ AND SAVE THESE INSTRUCTIONS

Model No.

CF700AW07 CF700WPB07

CF700WW07 CF700BS07

CF700AB07 CF700WB07

CF700PB07 CF700OB07

CF700PBW07 CF700CK07

Net Weight: 13.7 Lbs.

®

BUILDER Series

Ceiling Fan Owner's Manual

Part No. F40BP71810009

Form No. BP7181-9

 

 

!WARNING

WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.

Safety Instructions

1.Read your owner’s manual carefully and keep it for future reference.

2.Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel.

3.Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before servicing.

4.Do not put anything into the fan blades while they are turning.

5.Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions for Installation

1.To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.

2.All wiring must satisfy National and Local Electrical Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician.

3.The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support”, and use the mounting screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

4.The downrod furnished with the fan proves the minimum recommended floor to fan blade clearance for an 8 foot ceiling.

5.The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.

6.Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not know enough about electrical wiring, have your fan installed by a licensed electrician.

WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not specifically approved for this fan.

WARNING: This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use this product by Emerson Company could result in personal injury or property damage.

WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

Tools Required

Standard screwdriver

Wire stripper

Phillips screwdriver

Step ladder

!WARNING

Do not install or use fan if any part is damaged or missing. Call Toll-Free:

1-800-654-3545

!WARNING

This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Company. Substitution of parts or accessories not designated for use with this product by Emerson Company could result in personal injury or property damage.

!WARNING

If you feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician.

2

General

After opening the box you should find the following parts:

One motor housing assembly

One upper canopy

One set of blade flanges

One hanger bracket

One downrod/hanger ball assembly

Parts bag

One set of blades

One switch housing cover

One Owner's Manual

Installation Instructions

!WARNING

The fan must be hung with at least 7' of clearance from floor to blades.

1.If your fan is to replace an existing ceiling light fixtures, turn electricity off at the main fuse box at this time and remove the existing light fixture.

!WARNING

Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local Codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.

!WARNING

To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box marked “Acceptable for Fan Support”, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

!WARNING

The outlet box and joist must be securely mounted and capable of supporting at least 50 lbs. Use only a U.L. outlet box listed as “Acceptable for Fan Support”.

2.Install hanger bracket (item 1) to outlet box using the two screws supplied with the outlet box. Hanger bracket must seat firmly against outlet box. Remove wall board if necessary until bracket contacts box.

!WARNING

Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall.

3.Run the downrod (item 3) through the ceiling cover (item 4). Run the three wires from the fan through the downrod.

4.The fan is supplied with a hanger ball/downrod assembly. Slide the downrod (Item 3) into motor mount adapter until the hole in the downrod aligns with the cross hole in the adapter. (Make sure wires do not twist during this step.) Next, insert clevis pin through cross holes in adapter and downrod. Install hairpin clip in hole in clevis pin. Now tighten the downrod setscrews securely to the downrod.

!WARNING

It is critical that the clevis pin in the motor mount adapter is properly installed and the setscrews securely tightened. Failure to verify that the clevis pin and setscrews are properly installed could result in the fan falling.

5.To attach switch housing (item 5) align the color stripes of connectors. Slide the connectors together until plastic latch on connector snaps over the tab on connector. Carefully tuck all wires and splices into the switch housing. Position switch housing (item 5) on plate and align the holes in the switch housing by installing the three screws in the side of plate.

NOTE: To install an accessory light kit, remove switch housing (item 5) and make light kit electrical connections to blue and white leads marked “For Light” in the switch housing. Follow light kit instructions for wiring and installation. Then reinstall switch housing as outlined above.

6.Lift the fan, without blades, and put the downrod assembly into the hanger bracket. Make sure to engage the groove on the hanger ball (item 2) with the tab on the hanger bracket (item 1) to prevent rotation.

!WARNING

Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard.

!WARNING

To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and hanger bracket.

WIRING THE FAN. If you do not have enough electrical experience, have your fan installed by a licensed electrician.

NOTE: This fan comes with 80” long electrical leads. Before installing the fan, measure approximately 6 to 9 inches above the hanger ball/downrod assembly. Cut off excess leads and strip back insulation 1/2-inch from end of leads.

!WARNING

Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.

3

Loading...
+ 5 hidden pages