Size:
436.55 Kb
Download

PAN • TILT • ZOOM COLOR CAMERA

PTC-200C

INSTRUCTION MANUAL

Please read this instruction manual carefully before using this PTC-200C

and keep it for future reference.

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus outdoors.

6.Do not use this apparatus near water.

7.Clean only with dry cloth.

8.Do not install near heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.

9.Do not touch this apparatus during lightning storms.

10.Unplug when unused for long periods of time.

11.Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supplycord or plug is damaged, liquid has been spilled or objects have been fallen onto the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

- 1 -

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

Do not use any power supply other than specified.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

* The CAUTION label is attached on the base of product.

INFORMATION

This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, use, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

USER-INSTALLER

CAUTION: Your authority to

operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party responsible for compliance to Part of the FCC Rules.

- 2 -

HANDLING PRECAUTIONS

Be sure to use the provided AC adapter.

Do not leave the Camera under direct sunlight or by heater, or the Camera may be discolored, or damaged.

Do not place the Camera in any humid, dusty, windy or vibrating location. Use the Camera in the following environmental condition:

Temperature:

0 °C ~ 40 °C (32 ° ~ 104 °F)

Humidity:

30% ~ 85% (No condensation)

Use a soft, dry cloth for cleaning. Do not use any volatile solvent, such as thinner or benzine.

Do not directly point the camera lens into the sun, or the camera may be damaged.

Caring for the batteries:

If the Camera is not used for long time, remove the batteries from the remote controller.

Do not use rechargeable Ni-Cdbatteries.

Do not use new and old batteries, or batteries of different type together.

Do not try to recharge or short-circuitthe batteries.

Do not operate the PAN/TILT motion continuously for a long time, or the

life of the Camera will be shortened.

- 3 -

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS .........................................

 

 

 

1

HANDLING PRECAUTIONS ............................................................

 

 

 

 

 

 

 

3

1. PART NAMES AND FUNCTIONS....................................................

 

 

 

 

 

5

2. WIRELESS REMOTE CONTROLLER

.............................................

7

 

 

 

 

3. SETTING UP

....................................................................................

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4. OPERATION PROCEDURES

........................................................

14

 

 

 

 

 

 

[1] Power supply to the Camera

.....................................................

14

 

 

 

 

 

[2] Turning ON/OFF of the Camera power

.....................................

14

 

 

[3] Operating PAN/TILT

..................................................................

15

 

 

 

 

 

 

 

 

 

 

[4] Lens operation

...........................................................................

16

 

 

 

 

 

 

 

 

 

 

 

 

 

[5] BLC (Back Light Control)

...........................................................

17

 

 

 

 

 

 

 

[6] Preset operation

........................................................................

17

 

 

 

 

 

 

 

 

 

 

 

 

5. THE ID NUMBER SETTING

...........................................................

18

 

 

 

 

 

 

 

6. OSD (On-ScreenDisplay)

..............................................................

19

 

 

 

 

 

 

 

 

7. ALARM IN/OUT TERMINALS

........................................................

22

 

 

 

 

 

 

[1] Alarm input

................................................................................

22

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[2] Alarm output

..............................................................................

22

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8. ALL CLEAR SWITCH

.....................................................................

23

 

 

 

 

 

 

 

 

 

 

 

9. RS-485

...........................................................................................

24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10. TERMINATING RESISTANCE AND ID ADDRESS SETTINGS

....

25

 

[1] Setting the terminating resistance

.............................................

25

 

 

 

 

[2] Setting the ID address

...............................................................

25

 

 

 

 

 

 

 

 

 

11. TROUBLESHOOTING HINTS

........................................................

28

 

 

 

 

 

 

12. SPECIFICATIONS..........................................................................

 

 

 

 

 

 

 

 

 

 

 

 

29

13 SUPPLIED ACCESSORIES

...........................................................

 

 

 

 

 

 

30

- 4 -

1. PART NAMES AND FUNCTIONS

Overall View

LED

INFRARED SENSOR

BASE

LENS

CAMERA HEAD

ALARM IN TERMINAL

TERMINAL BLOCK RS-485IN TERMINAL

DIP Switch (4)

DIP Switch (10)

RS-485OUT TERMINAL

ALARM OUT TERMINAL

DC IN

INFRARED SENSOR

COMPOSITE-VIDEOOUT(RCA pin jack)

This camera is designed to mount on ceiling panels only.

- 5 -

Wireless Remote Controller

 

 

POWER

15 RESET

 

1

14 BACK LIGHT

 

 

 

 

 

 

17 ID

2

OPEN

 

16 PRESET

 

 

 

5

NEAR

 

3

CLOSE

FAR

18 NUMBER (1 6)

 

6

 

4

AUTO

AUTO

 

 

7

11 HOME

 

 

 

 

8

TELE

10 Directions

 

 

 

9

WIDE

 

 

 

12 MENU

13 CURSOR/PAN-TILT

No.

 

 

 

 

 

 

 

 

 

Button Name

 

Function

 

Reference Page

 

 

 

 

 

 

POWER

 

 

To turn ON/OFF the Camera power.

 

P.19

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

OPEN

 

 

To open the iris manually.

 

P.16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

CLOSE

 

 

To close the iris manually.

 

P.16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

AUTO

 

 

To iris automatically.

 

P.16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

NEAR

 

 

To move the focus near.

 

P.16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

FAR

 

 

To move the focus far.

 

P.16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO

 

 

To focus automatically.

 

P.16

 

 

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

TELE

 

 

To zoom in.

 

P.16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WIDE

 

 

To zoom out.

 

P.16

 

 

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Direction

 

 

To change the Camera head direction.

 

P.15

 

 

 

10

 

 

 

 

 

 

 

(

)

 

To operate the OSD*1 cursor.

 

P.19, P.20, P.21

 

 

 

 

 

 

HOME

 

 

To turn the Camera head to the front.

 

P.15

 

 

 

11

 

 

 

 

 

 

 

 

 

 

To operate the OSD*1 cursor.

 

P.19, P.20, P.21

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MENU

 

 

To turn ON/OFF the OSD*1 display.

 

P.18,P.19,P.20,P.21

 

 

 

12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CURSOR/

 

 

To switch the operation mode between the menu

 

P.19

 

 

 

 

13

 

 

 

 

 

 

 

PAN-TILT

 

 

operation and the PAN-TILToperation.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BACK LIGHT

 

Back light control.

 

P.17, P.20

 

 

 

 

14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RESET

 

 

To readjust the Camera head and LENS position.

 

P.15

 

 

15

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PRESET

 

 

To register the preset.

 

P.17

 

 

 

16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

17

 

ID

 

 

To operate multiple Cameras individually.

 

P.14, P.18

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NUMBER

 

 

To set the preset position and the ID No.

 

P.17, P.18

 

 

 

18

 

 

 

 

 

 

 

(1~6)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*1 OSD (On-ScreenDisplay)

 

 

 

 

 

 

 

 

 

 

 

- 6 -

 

 

 

2. WIRELESS REMOTE CONTROLLER

Point the infrared emitting window of the wireless remote controller at the infrared sensor of the Camera, located at the front, and the rear panel, and select the desired function.

Receivable range

Note: The infrared sensors may receive the infrared rays only within a narrower receivable range or may not receive them at all depending on the ambient environment, such as being placed under the sunlight or near an inverter fluorescent lamp. In such case, relocate the installation place of the receiving side or block off the sunlight.

- 7 -

Preparation

Remove the battery case cover by pressing downward on the [] mark part in the direction as indicated by the arrow.

Install 2 pcs. of batteries (type R03,AAA) into the case in the direction as indicated there.

Note: Install the batteries with the proper

to

and

to

polarity.

Note: For dry cells, be sure to use the size AAA.

Note: Change the batteries at least once a year or when even nesessary.

Note: The batteries supplied with the Camera are only for use in initially confirming the operation of the Camera.

It is not guaranteed that these batteries will work effectively for the indicated period.

When multiple Cameras are operated through the wireless remote

controller

Refer to "5. THE ID NUMBER SETTING" on P. 18.

- 8 -

3.SETTING UP

[1]Installation

Note: When carrying the Camera, be sure to hold the base.

Note: Do not turn the Camera head in thePAN-TILTdirection by hand, or the Camera head may be broken.

(1) Mounting the Fixing Plate

Put 4 Hexagon Head Bolts M5x40 (supplied)

SCREW M3x5 (attached) , 4 PCS through the Fixing Plate, and screw the Fixing Plate to the Main Unit with 4 Screws M3x5 (supplied).

FIXING PLATE

HEXAGON HEAD BOLT M5x40, 4 PCS

Note: For fastening the Fixing Plate, be sure to use the 4Phillips-headScrew M3x5 (supplied). Be careful that using any screws other than the supplied may damage the inside of the Main Unit. (Do not use longer screws)

MAIN UNIT

- 9 -