Elmo Ceiling Presenter HV-C1000XG User Manual.pdf

9.67 Mb
Loading...

CEILING PRESENTER

HV-C1000XG

INSTRUCTION MANUAL

Please read this instruction manual carefully before using this product and keep it for future reference.

IMPORTANT SAFEGUARDS

Read Instructions – All the safety and operating instructions should be read before the appliance is operated.

Retain Instructions – The safety and operating instructions should be retained for future reference.

Heed Warnings – All warnings on the product and in the operating instructions should be adhered to.

Follow Instructions – All operating and use instructions should be followed.

Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards.

Water and Moisture – Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the

manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer.

Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.

Power Sources – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

1

Grounding or Polarization – This product may be equipped with either a polarized 2-wire AC line plug (a plug having one blade wider than the other) or a 3-wire grounding type plug, a plug having a third (grounding) pin. The 2-wire polarized plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. The 3- wire grounding type plug will fit into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug.

Power-Cord Protection – Powersupply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

A product and

cart combination

should be moved with care. Quick

stops, excessive force, and uneven

surfaces may cause the product and cart combination to overturn.

Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

WARNING : Handling the cord on this product or cords associated with accessories sold with this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.

Wash hands after handling.

2

Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

When the power-supply cord or plug is damaged.

If liquid has been spilled, or objects have fallen into the product.

If the product has been exposed to rain or water.

If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

If the product has been dropped or damaged in any way.

When the product exhibits a distinct change in performance - this indicates a need for service.

Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

When the lamp is ON, don't touch the lamp or lamp cover.Negligence could result in burned injury.

Don't use this outdoors.Negligence could result in electric shock or fire.

CAUTION

RISK OF

ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK).

NO USER-SERVICEABLE

PARTS INSIDE.

REFER SERVICING TO

QUALIFIED SERVICE

PERSONNEL.

3

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous

SA 1965 voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This marking is located at the bottom of product.

 

The exclamation point within

 

a n e q u i l a t e r a l t r i a n g l e i s

 

intended to alert the user to

 

t h e p r e s e n c e o f i m p o r t a n t

SA 1966

operating and maintenance

(servicing) instructions in the

literature accompanying the product.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

THIS IS A CLASS A PRODUCT.

IN A DOMESTIC ENVIRONMENT THIS PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER MAY BE REQUIRED TO TAKE

ADEQUATE MEASURES.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

USER-INSTALLER CAUTION:

Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party responsible for compliance to Part 15 of the FCC rules.

4

BEFORE YOU USE

Use this product under the rated electrical conditions.

Do not leave this product under direct sunlight or by heaters, or this product may be discolored, deformed, or damaged.

Do not place this product in any humid, dusty, windy or vibrating location. Use this product in the following environmental conditions: Temperature: 5°C~40°C (41°F~104°F)

Humidity:

30%~85% (No condensation)

Use a soft, dry cloth for cleaning. Do not use any volatile solvent, such as thinner or benzine.

Do not directly point the camera lens into the sun, or the camera may be damaged.

Although this product is equipped with a lamp, it is not a lighting system.

Do not use this product primarily as a lighting unit. Such use may cause fire or accident.

Caring for the batteries:

If this product is not used for a long time, take out the batteries from the wireless remote control.

Do not use rechargeable Ni-Cd batteries.

Do not use new and old batteries, or batteries of different types together.

Do not try to recharge or short-circuit the batteries.

5

CONTENTS

 

1. PART NAMES AND FUNCTIONS

 

Appearance .......................................................

8

Connector Panel ..................................................

9

Wireless Remote Control .....................................

10

2. WIRELESS REMOTE CONTROL

 

Receivable Range ..............................................

12

Preparation ......................................................

12

3. MOUSE

 

Mouse Operation ..............................................

13

4. INSTALLATION

 

Installation of the Unit ............................................

14

Setting of Auto Focus Operating Range ...................

14

Connection to Monitor and Projector ......................

15

Connection to the analog RGB-out terminal .....................

15

Connection to the composite video-out terminal ................

15

Connection to the S video-out terminal ...........................

15

5. OPERATION PROCEDURES

 

Simple Steps for Presenting Printed Material .............

16

6. VARIOUS FUNCTIONS AND OPERATION

 

Lighting ...........................................................

17

Zoom ..............................................................

17

Digital Magnification ..........................................

18

Color / B&W Selection ......................................

19

Posi / Nega Conversion .....................................

20

Image Rotation ..................................................

20

Pause..............................................................

21

Contrast ..........................................................

21

F.A.M. (Frame Accumulate Mode)..........................

22

Iris .................................................................

22

Auto iris adjustment ...................................................

22

Focus ..............................................................

23

Auto Focus ..............................................................

23

Powered Manual Focus ..............................................

24

Preset Operation ...............................................

25

Image Memory ..................................................

26

"Utility Software CD-ROM" ...................................

26

7. OSD (On-Screen Display)

 

OSD Operation .................................................

27

Main Menu ......................................................

28

Sub Menu ........................................................

30

1.

PART NAMES

1

 

AND FUNCTIONS

 

2.

WIRELESS REMOTE

2

 

CONTROL

 

 

3.MOUSE 3

4.INSTALLATION 4

5.OPERATION 5 PROCEDURES

6.

VARIOUS FUNCTION

6

 

AND OPERATIONS

 

 

7.OSD 7

8.RS-232C 8 SPECIFICATIONS

9. REPLACING

9

THE LAMP

 

10.TROUBLESHOOTING 10 HINTS

6

1

1.

PART NAMES

 

 

AND FUNCTIONS

2

2.

WIRELESS REMOTE

 

CONTROL

 

 

3

3.

MOUSE

4

4.

INSTALLATION

5

5.

OPERATION

 

PROCEDURES

 

 

6

6.

VARIOUS FUNCTION

 

AND OPERATIONS

 

 

7

7.

OSD

8

8.

RS-232C

 

SPECIFICATIONS

 

 

9

9.

REPLACING

 

THE LAMP

 

 

10

10. TROUBLESHOOTING

 

 

HINTS

CONTENTS

 

8. RS-232C SPECIFICATIONS

 

Setting Up........................................................

32

Cable Connection..............................................

32

Connection ......................................................

33

Transmission Specifications ..................................

33

Data Format Specifications...................................

33

Transmission command (PC → Ceiling Presenter) ..............

33

Response data format (Ceiling Presenter → PC)................

34

UART Communication Format ................................

35

9. REPLACING THE LAMP

 

Replacing the Lamp ............................................

37

10. TROUBLESHOOTING HINTS

 

Symptoms and Confirmation .................................

38

11. SPECIFICATIONS

 

General..................................................................

39

Camera ..................................................................

40

Lighting ..................................................................

40

Supplied Accessories .................................................

41

Optional parts (to be purchased separately) ....................

41

7

1 PART NAMES AND FUNCTIONS

Appearance

Ceiling mounting screw hole

Lamp cover

Setscrew

Ventilation outlet

Halogen lamp

Infrared ray receptor

Lens

LED

1

2

3

4

5

6

7

8

9

10

8

Connector Panel

1

 

 

RS-232C Terminal

 

Analog RGB-out

Power Cord

Power Supply Switch

 

 

[RS-232C]

 

Terminal [RGB OUT]

Receptacle[AC IN]

[POWER]

2

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

A BCD

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

Mouse

 

 

 

 

 

DIP Switches

 

5

 

Terminal

USB Terminal

Video-out Terminal [S-VIDEO/VIDEO]

 

 

[MOUSE]

 

 

[USB]

 

S-Video (Mini DIN 4P)

 

 

 

 

 

 

 

 

 

 

 

 

 

Composite Video (RCA pin jack)

 

 

6

 

Name

 

 

 

 

Function

 

Reference Page

1

RS-232C Terminal

 

To connect the RS-232C cable when

 

P.32

 

 

[RS-232C]

 

 

controlling the unit from the PC.

 

 

 

 

 

 

 

 

2

Analog RGB-out

 

Image is output when this terminal is

 

P.15

7

 

Terminal

 

 

connected to RGB input equipment

 

 

 

 

 

 

 

[RGB OUT]

 

 

(e.g., LCD projector, multi-sync monitor).

 

 

 

3

Mouse Terminal [MOUSE]

To connect the mouse (supplied accessory)(*1).

P.13

8

4

USB Terminal [USB]

 

If connected to

personal

computer with

P.26

 

 

 

 

the attached USB cable, it is possible to

 

 

 

 

 

 

 

 

 

 

transfer images and control the unit by

 

 

 

 

 

 

using the software in the attached Utility

 

 

 

 

 

 

Software CD-ROM.(*1)

 

 

 

9

5

Video-out Terminal

 

To output images to the NTSC/PAL

 

P.15

 

 

[S-VIDEO/VIDEO]

 

monitor, such as TV monitor.

 

 

 

 

S-Video (Mini DIN 4P)

 

 

 

 

 

 

 

 

Composite Video

 

 

 

 

 

 

 

10

 

(RCA pin jack)

 

 

 

 

 

 

 

 

6

DIP Switches

 

 

The functions can be changed as follows:

P.14

P.15

 

 

 

 

 

 

 

 

[A] key: To change the video output type.

 

 

 

 

 

[B] key: To change the screen size of video output.

 

 

 

 

 

 

 

[C] key: Selects the operating range of AF.

 

 

11

 

 

 

 

[D] key: Selects the operating range of AF.

 

 

 

 

 

 

Key alignment and functions:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[A] key

[B] key

[C] key [D] key

 

 

 

 

 

 

 

0

NTSC

Over scan

AF range selected

 

 

 

 

 

 

 

1

PAL

Under scan

(See P. 14.)

 

 

 

 

 

 

 

 

Before changing the DIP Switch keys, be

 

 

 

 

 

 

 

 

sure to turn OFF the power supply to this

 

 

 

 

 

 

 

 

product.

 

 

 

 

(*1) For cable extension, use a cable specified for extension that is commercially available.

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Name

Function

Reference Page

 

 

 

7

Power Cord Receptacle

Connected to the power cord connector.

 

 

 

 

 

[AC IN]

 

 

 

 

 

8

Power Supply Switch

To turn ON/OFF the power supply.

 

 

 

[POWER]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Wireless Remote Control

1 POWER

2 PAUSE

3 2X

6 PRESET.SET

7 PRESET.CALL

10 POSI/NEGA

11 COLOR/B&W

14 MENU

17 ZOOM.TELE

18 ZOOM.WIDE

22IRIS.NORMAL 23 IRIS.OPEN

POWER

 

 

 

 

 

PAUSE

 

 

 

4 ARROWS

 

 

 

 

5 MEMORY NO.

SET PRESET CALL

SET IMAGE CALL

8 IMAGE.SET

9 IMAGE.CALL

 

 

 

 

POSI/NEGA

COLOR/B&W CONTRAST

LAMP

12

CONTRAST

13

LAMP

 

 

 

 

MENU

 

IMAGE ROTATION F.A.M.

15 IMAGE ROTATION

 

 

 

 

16

F.A.M.

TELE ZOOM WIDE

NEAR FOCUS FAR

19 FOCUS.NEAR

 

 

 

 

20

FOCUS.FAR

NORMAL

OPEN

CLOSE

AF

 

 

 

21

AUTO FOCUS

 

 

 

 

 

IRIS

 

 

 

 

 

 

 

 

24

IRIS.CLOSE

1

2

3

4

5

6

7

8

9

10

11

10

1

2

3

4

5

6

7

8

9

10

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Button Name

Function

Reference Page

 

 

1

POWER

 

 

To turn ON/OFF the power supply.

P.16

 

 

2

PAUSE

 

 

To switch pause/motion of the image.

P.21

 

 

 

 

 

 

 

 

 

 

3

DIGITAL

 

2X

To double the image size.

P.18

 

 

 

MAGNIFICATION

 

 

 

 

4

ARROWS

To scroll the magnified screen. This can

 

 

 

 

 

 

 

also be used to move the pointer when

 

 

 

 

 

 

 

the pointer is displayed.

 

 

 

 

 

 

 

 

 

 

 

5

MEMORY NO.

The memory No. Used with 6 to 9 .

 

 

 

 

 

 

 

 

 

 

 

6

STATUS

PRESET.SET

To store the operating condition of the

P.25

 

 

 

 

 

 

unit. Used with the MEMORY NO.

 

 

 

 

 

 

 

 

 

7

 

PRESET.CALL

To call the stored operating condition.

 

 

 

 

 

 

 

Used with the MEMORY NO.

 

 

 

 

 

 

 

 

 

 

 

8

IMAGE

IMAGE.SET

To store images in the unit's memory.

P.26

 

 

 

 

 

 

Used with the MEMORY NO.

 

 

 

 

 

 

 

 

 

 

 

IMAGE.CALL

.

 

 

 

9

 

 

 

 

 

To call the image stored by [IMAGE.SET]

 

 

 

 

 

 

 

button. Used with the MEMORY NO.

 

 

 

 

 

 

 

 

 

 

 

10

POSI/NEGA

To change POSI/NEGA.

P.20

 

 

11

COLOR/B&W

To change COLOR/B&W.

P.19

 

 

12

CONTRAST

To turn ON/OFF the contrast enhancement.

P.21

 

 

13

LAMP

 

 

To turn ON/OFF the lamp.

P.17

 

 

14

MENU

 

 

To turn ON/OFF the pointer and the OSD menu.

P.27

 

 

 

 

 

 

Determine the OSD menu pointed by the pointer.

 

 

 

15

IMAGE ROTATION

To rotate the image anticlockwise by 90°.

P.20

 

 

 

 

 

 

 

 

 

 

16

F.A.M.

 

 

To reduce the rough noise of the image.

P.22

 

 

17

ZOOM

TELE

To zoom in.

P.17

 

 

 

 

 

 

 

 

 

18

 

WIDE

To zoom out.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

19

FOCUS

NEAR

To move the focus near.

P.24

 

 

 

 

 

 

 

 

 

20

 

FAR

To move the focus far.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

21

 

AUTO FOCUS

To focus automatically.

P.23

 

 

22

IRIS

NORMAL

To reset the AUTO IRIS to the initial value.

P.22

 

 

23

 

OPEN

To open the AUTO/MANUAL IRIS.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24

 

CLOSE

To close the AUTO/MANUAL IRIS.

 

 

 

11

2 WIRELESS REMOTE CONTROL

Receivable Range

Point the infrared emitting part of the wireless remote control at the infrared sensor of this product, and press the button for desired function. The receivable range may be narrowed or the light may not be received when this product is placed under sunlight, near an inverter fluorescent lamp or in any other unfavorable surroundings. Take measures such as shielding the sunlight and the light from inverter fluorescent lamp.

• Receivable range

Distance : Approx. 7 m (23 ft.) or less from the light receiving area to the front of the wireless remote control.

Angle : Approx. 30° degrees or less from the light receiving area upward and downward, approx. 50°degrees or less from the light receiving area rightward and leftward.

Preparation

Remove the battery case cover by pressing downward on the [ OPEN] mark part in the direction as indicated by the arrow.

Install 2 pcs. of batteries (type R03, AAA) into the case in the direction as indicated there.

Install the batteries according to palarity.

Change the batteries once a year.

The batteries supplied with this product are only for use in initially confirming the operation of this product. It is not guaranteed that these batteries can work effectively for the indicated period.

1

2

3

4

5

6

7

8

9

10

12

1

2

3

4

5

6

3 MOUSE

Mouse Operation

Connect the mouse to the mouse terminal [MOUSE] on the connector panel.

• Click the left button

To operate the OSD menu.

When digital magnification or image rotation (90°, 270°) is not used, the pointer and OSD menu can be displayed/deleted.

Drag by left button (moves while button is being pushed) In time of digital magnification or image rotation (90°,270°), screen is scrolled.

Click the mouse wheel

To display or clear the pointer and OSD menu alternately by clicking.

Mouse

Right button

Left button

Center button

Mouse wheel

The pointer

 

The OSD

 

The OSD

 

The pointer

is displayed.

Click

menu is

Click

menu is

Click

is cleared.

 

displayed.

cleared.

 

 

 

 

 

 

Click

7

• Roll the mouse wheel

To scroll the screen up/down when the image is in digital magnification or rotated to 90°

 

 

or 270°.

8

• Click the right button

When this button is clicked for digital magnification while the pointer is displayed,

the position of the pointer is the center of the magnified image.

When the pointer is not displayed, the center position of the image is digitally magnified.

9

Click the OSD menu, then the menu functions are given priority.

 

When using the mouse, connect the mouse before turning ON the power supply to this product.

10

Use the attached mouse. If another mouse is used, the normal operation cannot be guaranteed.

 

If the cable is extended, use the commercial cable for extension or consult the distributor.

The OSD menu is assumed to be used for large projection sizes with a projector or the like. Therefore, the display on a hand monitor or a TV may be hard to see.

Reference Page

• Digital Magnification

P.18

 

 

• OSD ...............................

P.27

13

4 INSTALLATION

Installation of the Unit

For the ceiling mounting metal piece, VB-1000 separately available, any product approved by UL Standard for projector which is capable of supporting a load of 8-10 kg or more, or similar product also approved by UL Standard shall be used. Request your distributor to install this product on the ceiling. For details, refer to the HV-C1000XG Installation Manual included in the package.

Connect the power supply cord with the Power Cord

Receptacle of this product and plug outlet.

Turn ON the Power Supply Switch.

When this product is not used for a long time, turn OFF the Power Supply Switch or remove the power supply plug from the outlet.

Provide a distance of 1.3m or more between the unit and the document to be projected.Images can be focused when the distance increases; however, the light intensity may be insufficient.If the distance is more than 3m, external lighting is needed.

Setting of Auto Focus Operating Range

The following settings of this product can be changed with the DIP Switches. Change the settings according to the connection environment. The factory settings are as shown in the following table:

AF operating range (Shooting distance)

[C] key

[D] key

Whole area

(1.3m

)

0

0

1.3m

1.8m

 

1

0

1.7m

2.8m

 

0

1

2.7m

 

 

1

1

In delivery from plant, the whole area is set.

When changing the DIP Switch keys, be sure to turn OFF the power supply to this poduct beforehand.

1

2

3

4

5

6

7

8

9

10

14

1

2

3

Connection to Monitor and Projector

The following settings of this product can be made with the DIP Switches. Make the settings according to the connection environment. The factory settings are as shown in the following table:

 

 

Initial setting

Key

Function

Key selection

Content

A

To change the Video output type

1

NTSC

B

To change the screen size of Video output

0

Over scan

Be sure to turn OFF the power supply to all equipment before making any connections to protect this product and all the connected equipment.

4

When changing the DIP Switch keys, be sure to turn OFF the power supply to this product

beforehand.

5

Connection to the analog RGB-out terminal

Connect the Analog RGB-out Terminal [RGB OUT] to the equipment with an analog RGB-in

terminal with the analog RGB cable (attached) or a connection cable available on the market.

 

 

At this time, the position of the display may be deviated from the center. If deviated, manually

 

adjust the horizontal and vertical positions on the connected equipment.

6

Also, vertical stripes may appear on the screen of the LCD projector. That can be alleviated

by manually adjusting the dot clock frequency on the projector.

LCD projector

7

8

9

10

RS-232C

RGB OUT

AC IN POWER

 

 

CRT monitor

MOUSE USB

VIDEO S-VIDEO

or

 

 

Connection to the composite video-out terminal

Use the Composite Video-out Terminal [VIDEO](RCA pin) and the video cable with RCA pin plug as attached or available on the market.

RS-232C

RGB OUT

AC IN POWER

TV monitor

MOUSE USB

VIDEO S-VIDEO

 

 

Connection to the S video-out terminal

Use the S Video-out Terminal [S-VIDEO](Mini DIN 4P) and the S-Video cable as attached or available on the market.

RS-232C

RGB OUT

AC IN POWER

TV monitor

MOUSE USB VIDEO S-VIDEO

Hold the cable plug when connecting or disconnecting the cables.

15

5 OPERATION PROCEDURES

Simple Steps for Presenting Printed Material

(1)Push the [POWER] button of the wireless remote control to turn ON the power (Indicator LED on the unit turns from red to green).

Connection with the monitor should be done in advance.

If the Power Supply Switch is turned ON immediately after it is turned OFF, this product may not operate.

To restart operation, turn ON the Power Supply Switch after several seconds.

Wireless remote control

(1) (4)

(2) (3)

When the document surface is dark, turn ON the lamp by pressing the [LAMP] button.

After the power supply is turned ON, it takes about 10 seconds to execute the initialization of the unit and output the image.

(2)Place an object on the document surface and adjust the image size using [ZOOM·TELE] and [ZOOM·WIDE] buttons on the wireless remote control as you watch the monitor screen so that the projected image may be in compliance with the object.

(3)Adjust the focus by pressing the [FOCUS·N/F] (NEAR/FAR) buttons of the wireless remote control. The focus can be also adjusted by pressing the [AF] (AUTO FOCUS) button.

(4)After finishing the operation, turn OFF the [POWER] button of the wireless remote control. (Indicator LED on the unit turns from green to red.)

Wireless remote

TELE ZOOM

NORMAL

Wireless remote

TELE ZOOM WIDE

NEAR FOCUS FAR

NORMAL

OPEN

CLOSE

AF

 

IRIS

1

2

3

4

5

6

7

8

9

10

16

6 VARIOUS FUNCTIONS AND OPERATION

1

 

Lighting

2

Lighting for presenting information such as printed

materials is provided.

 

When the [LAMP] button on the wireless remote

 

control is pressed, the lamp is lit.

3

When the [LAMP] button is pressed again, the lamp

goes off.

T o o b t a i n a s h a r p i m a g e w i t h g o o d c o l o r rendering, it is sometimes necessary to use the

4

lighting.

 

 

W h e n t h e l i g h t i n g p r o v i d e d b y t h e u n i t i s

 

insufficient, use external lighting.

5

6

Zoom

7

Press the [ZOOM.TELE] button on the wireless remote control, and the image will gradually be magnified.

8 Press the [ZOOM.WIDE] button on the wireless remote control, and the image will gradually be reduced.

Also, by continuously pressing the ZOOM button, the 9 zooming speed becomes faster. (Double speed

function)

10

Wireless remote control

Wireless remote

POSI/NEGA

COLOR/B&W CONTRAST LAMP

MENU

IMAGE ROTATION F.A.M.

remote control

CALL

SET IMAGE CALL

COLOR/B&W CONTRAST

LAMP

 

IMAGE ROTATION F.A.M.

ZOOM WIDE

NEAR FOCUS FAR

OPEN

CLOSE

AF

IRIS

 

 

Wireless remote control

TELE ZOOM WIDE

NEAR FOCUS FAR

NORMAL

OPEN

CLOSE

AF

 

17

Digital Magnification

To double the image, press the [2x] button on the wireless remote control or click the Right button of the mouse.

Enlarged screen can be scrolled by operating the arrow button on the wireless remote control or by operating the mouse.

If the OSD menu is displayed on the digitally magnified screen, the magnified screen cannot be scrolled by the wireless remote control.

Wireless remote control

POWER

PAUSE

SET PRESETCALL

SET IMAGE CALL

POSI/NEGA

COLOR/B&W CONTRAST

LAMP

MENU

 

IMAGE ROTATION F.A.M.

TELE ZOOM WIDE

NEAR FOCUS FAR

NORMAL

OPEN

CLOSE

AF

 

IRIS

 

 

Wireless remote control

The mouse can be operated as follows:

• Left button........ To scroll the image

according to the dragging of the mouse while holding down the left button.

• Mouse wheel .... To scroll up/down the magnified screen.

• Right button ..... To turn ON/OFF the double enlargement. When any image is magnified digitally, the pointer becomes the mark .

When the digital magnification is tried while the mouse pointer is in display, since the left button of the mouse is limited to the scroll function, the mouse pointer and the OSD menu cannot be turned ON/OFF.

To turn ON/OFF the mouse pointer and the OSD menu, turn OFF the digital magnification.

SET PRESET CALL SET IMAGE CALL

 

 

Reference Page

 

 

 

 

 

 

 

 

 

 

 

• Mouse

................

P.13

 

 

 

 

 

 

 

 

• OSD ....................

 

P.27

 

 

 

1

2

3

4

5

6

7

8

9

10

11

18

Color / B&W Selection

1

To present the B&W (Black&White) material such as documents. Sharper image with no color blur on the monitor can be produced.

2 If the [COLOR/B&W] button on the wireless remote control is pressed, images are switched.

3

When PAUSE is effective, COLOR/B&W selection

does not work.

4

5

6

7

8

9

10

11

Wireless remote control

POWER

PAUSE

SET PRESETCALL

SET IMAGE CALL

POSI/NEGA

COLOR/B&W CONTRAST

LAMP

MENU

 

IMAGE ROTATION F.A.M.

TELE ZOOM WIDE

NEAR FOCUS FAR

NORMAL

OPEN

CLOSE

AF

 

IRIS

 

 

Wireless remote control

POSI/NEGA

COLOR/B&W CONTRAST LAMP

MENU

IMAGE ROTATION F.A.M.

Reference Page

•OSD........ P.27

19

Posi / Nega Conversion

To show a negative film.

Press the [POSI / NEGA] button on the wireless remote control, the image will be converted to the NEGA mode accordingly.

When the [POSI / NEGA] button is pressed again, the POSI mode is resumed.

When using the NEGA conversion mode, use of the following is restricted.

With CONTRAST ON: Gamma adjustment is not available.

Only with Gamma setting γ = 07: CONTRAST can be turned ON.

NEGA setting at the factory

• Gamma: γ = 07 (0.3)

• CONTRAST: ON

When PAUSE is effective, POSI/NEGA conversion does not work.

remote control

PRESETCALL

SET IMAGE CALL

COLOR/B&W CONTRAST

LAMP

 

IMAGE ROTATION F.A.M.

ZOOM WIDE

NEAR FOCUS FAR

OPEN

CLOSE

AF

IRIS

 

 

Wireless remote control

POSI/NEGA

COLOR/B&W CONTRAST LAMP

MENU

IMAGE ROTATION F.A.M.

Reference Page

•OSD........ P.27

Image Rotation

When the [IMAGE ROTATION] button on the wireless remote control is pressed, the image rotates. Every time the [IMAGE ROTATION] button is pressed, the image rotates counterclockwise by 90°.

The image does not rotate when PAUSE mode is working.

Wireless remote control

POWER

PAUSE

SET PRESETCALL

SET IMAGE CALL

POSI/NEGA

COLOR/B&W CONTRAST

LAMP

MENU

 

IMAGE ROTATION F.A.M.

TELE ZOOM WIDE

NEAR FOCUS FAR

NORMAL

OPEN

CLOSE

AF

 

IRIS

 

 

Wireless remote control

MENU

IMAGE ROTATION F.A.M.

TELE ZOOM WIDE

NEAR FOCUS FAR

Reference Page

•OSD........ P.27

1

2

3

4

5

6

7

8

9

10

11

20

Pause

1

When the [PAUSE] button on the wireless remote control is pressed, the image from the unit’s camera pauses. When the [PAUSE] button is pressed again,

2 the PAUSE mode is canceled.

W h e n P A U S E i s e f f e c t i v e , P O S I / N E G A conversion, IMAGE ROATION, COLOR/B&W

3

selection, F.A.M., and CONTRAST functions do

 

 

not work.

 

Although the ZOOM, FOCUS, and IRIS functions

4

are effective, the results are not reflected in the

image in this mode.

5

6

7

Contrast

 

 

To present the material with a little half tone such as

 

texts.

8

Images with sharp characters and lines contrasty with

background can be obtained.

 

 

When the [CONTRAST] button on the wireless

9

remote control is pressed, the image becomes

contrasty.

When the [CONTRAST] button is pressed again, the

 

 

image is reset to the normal condition.

10

When using NEGA conversion, the CONTRAST

can only be turned ON if Gamma setting is γ =07

 

 

(0.3).

11

CONTRAST does not function while PAUSE is

functioning.

remote control

CALL

SET IMAGE CALL

COLOR/B&W CONTRAST

LAMP

 

IMAGE ROTATION F.A.M.

ZOOM WIDE

NEAR FOCUS FAR

OPEN

CLOSE

AF

IRIS

 

 

Wireless remote control

PAUSE

Reference Page

•OSD........

P.27

Wireless remote control

POWER

PAUSE

SET PRESETCALL

SET IMAGE CALL

POSI/NEGA

COLOR/B&W CONTRAST

LAMP

MENU

 

IMAGE ROTATION F.A.M.

TELE ZOOM WIDE

NEAR FOCUS FAR

NORMAL

OPEN

CLOSE

AF

 

IRIS

 

 

Wireless remote control

POSI/NEGA

COLOR/B&W CONTRAST LAMP

MENU

IMAGE ROTATION F.A.M.

Reference Page

•OSD........ P.27

21

F.A.M. (Frame Accumulate Mode)

This is used to reduce artifacts of the image, and is appropriate to take pictures of still objects. Press the [F.A.M.] (Frame Accumulate Mode) button on the wireless remote control, and the [F.A.M.] is selected. Press the [F.A.M.] (Frame Accumulate Mode) button again, and the normal status is resumed.

[F.A.M.] does not function while the image is rotated or PAUSE is functioning.

remote control

PRESETCALL

SET IMAGE CALL

COLOR/B&W CONTRAST

LAMP

 

IMAGE ROTATION F.A.M.

ZOOM WIDE

NEAR FOCUS FAR

OPEN

CLOSE

AF

IRIS

 

 

Wireless remote control

MENU

IMAGE ROTATION F.A.M.

TELE ZOOM WIDE

NEAR FOCUS FAR

Iris

Auto iris adjustment

By adjusting the diaphragm, the brightness will automatically follow changes of brightness according to the object.

Press the [IRIS.OPEN] button on the wireless remote control to open the iris.

Press the [IRIS.CLOSE] button on the wireless remote control to close the iris.

Press the [IRIS.NORMAL] button on the wireless remote control, to change setting back to the defaults.

U s e R S - 2 3 2 C i n t e r f a c e f o r M A N U A L I R I S operation.

remote control

PRESETCALL

SET IMAGE CALL

COLOR/B&W CONTRAST

LAMP

 

IMAGE ROTATION F.A.M.

ZOOM WIDE

NEAR FOCUS FAR

OPEN

CLOSE

AF

IRIS

 

 

Wireless remote control

NORMAL

OPEN

CLOSE

AF

 

IRIS

 

 

Reference Page

•OSD........ P.27

1

2

3

4

5

6

7

8

9

10

11

22

1

Focus

 

 

Adjust the focus of the object.

2

Auto Focus

When the [AF](AUTO FOCUS) button on the

 

wireless remote control is pressed, the focus is set

 

automatically.

3

This product features a one-push AUTO FOCUS

function. Once focusing is completed, the AUTO

 

 

FOCUS function is released, and the focused position

4

maintains unchanged (FOCUSFREE).

The objects listed below may not be brought into

 

focus in the AUTO FOCUS mode. In these cases,

 

use the MANUAL FOCUS mode.

5

• Objects bearing little contrast

• Objects with fine repeated patterns, such as

 

 

lateral stripes and cross stripes

 

• Objects glittering or reflecting strong light

 

• Objects with bright background, or excessive

6

contrast

• The whole image is dark.

Objects located near and far away at the same time

Objects in motion

7

 

Some objects require a long auto focus time.

 

When the MANUAL FOCUS buttons ([FOCUS

8

·NEAR] or [FOCUS·FAR] button) on the.wireless

remote control are pressed,the AUTO FOCUS

operation is reset.

When the ZOOM buttons ([ Z O O M ·T E L E ] or 9 [ZOOM·WIDE] buttons) on the wireless remote control are pressed, the AUTO FOCUS operation

is suspended.

If some other operation is performed in AUTO 10 FOCUS operation, the AUTO FOCUS operation may

not be completed normally.

 

FOCUS can be adjusted at a distance of 1.3m or

11

more from the unit to the object in the max. side of

[ZOOM·TELE].

remote control

CALL

SET IMAGE CALL

COLOR/B&W CONTRAST

LAMP

 

IMAGE ROTATION F.A.M.

ZOOM WIDE

NEAR FOCUS FAR

OPEN

CLOSE

AF

IRIS

 

 

Wireless remote control

NORMAL

OPEN

CLOSE

AF

 

 

IRIS

 

 

Reference Page

•OSD........ P.27

23

Power Manual Focus

To focus on specific part of the material, such as 3-D material. Press the FOCUS button [FOCUS.NEAR] or

[FOCUS.FAR] on the wireless remote control.

This product can finely adjust the focus. For minor adjustments, press the FOCUS button several times. For major adjustments, keep the FOCUS button pressed, then the focus begins to move more quickly.

Focus can be adjusted at a distance of 1.3 m or more from the unit to the object in the max. side of

[ZOOM.TELE].

Wireless remote control

POWER

PAUSE

SET PRESETCALL

SET IMAGE CALL

POSI/NEGA

COLOR/B&W CONTRAST

LAMP

MENU

 

IMAGE ROTATION F.A.M.

TELE ZOOM WIDE

NEAR FOCUS FAR

NORMAL

OPEN

CLOSE

AF

 

IRIS

 

 

Wireless remote control

TELE ZOOM WIDE

NEAR FOCUS FAR

NORMAL

OPEN

CLOSE

AF

 

Reference Page

•OSD........ P.27

1

2

3

4

5

6

7

8

9

10

11

24

1

Preset Operation

Operation status of this product can be stored / read

 

 

out in the memory (max. 8 states can be stored).

2

Operation states that can be stored are as shown

below.

 

• Present zoom angle of view

 

• Status of IRIS

3

• White Balance status

• ON/OFF of Aperture

 

• Status of Gamma

 

• Lighting status

4

• Status of COLOR/B&W switch

• Condition including pointer ON/OFF, color and

 

shape

 

• Condition of IMAGE ROTATION

5

• ON/OFF of CONTRAST mode

• Status of POSI/NEGA conversion

 

 

• Status of F.A.M. selection

6

1. How to store

Press the [PRESET.SET] button on the wireless

 

 

remote control and press the MEMORY NO.

7

button of the wireless remote control within 4 sec

then the current status of this product is saved in

 

the pressed number memory.

The preset (stored) status is maintained even when

8

the power is turned OFF.

 

2.How to read out operation status

Press the [PRESET.CALL] button on the wireless

9 remote control and press the MEMORY NO. button of the wireless remote control within 4 sec then this product is set to the memorized status

corresponding to the number.

10

11

Wireless remote control

POWER

PAUSE

SET PRESETCALL

SET IMAGE CALL

POSI/NEGA

COLOR/B&W CONTRAST

LAMP

MENU

 

IMAGE ROTATION F.A.M.

TELE ZOOM WIDE

NEAR FOCUS FAR

NORMAL

OPEN

CLOSE

AF

 

IRIS

 

 

Wireless remote control

SET PRESET CALL

SET IMAGE CALL

POSI/NEGA COLOR/B&W CONTRAST

LAMP

Reference Page

•OSD........ P.27

25

Image Memory

Images can be stored / called in the memory of this product (max. 8 images).

1.Press the [IMAGE.SET] button on the wireless remote control and press the MEMORY NO. button of the wireless remote control within 4 sec then the image is stored in the pressed number.

When the Power Supply is turned OFF by pressing the [ P O W E R ] button of the wireless remote control, the images stored in the memory are deleted.

2.How to read out stored images

Press the [IMAGE.CALL] button on the wireless remote control and press the MEMORY NO. button of the wireless remote control within 4 sec then the image in the memory corresponding to the pressed number is read out.

To return to the normal camera image, press the [IMAGE.CALL] button again “within 4 seconds”.

The image cannot be saved in the number from which the image is read.

"Utility Software CD-ROM"

remote control

PRESETCALL

SET IMAGE CALL

COLOR/B&W CONTRAST

LAMP

 

IMAGE ROTATION F.A.M.

ZOOM WIDE

NEAR FOCUS FAR

OPEN

CLOSE

AF

IRIS

 

 

Wireless remote control

SET PRESET CALL

SET IMAGE CALL

POSI/NEGA COLOR/B&W CONTRAST

LAMP

Reference Page

•OSD........ P.27

The attached "Utility Software CD-ROM" contains the PC link software "Image Mate" and the TWAIN driver "ELMO TWAIN DS, "and can be operated as shown below.

To transfer graphic data to PC.

To operate this product by PC.

For details, see the Installation Manual for "Utility Software" and "manual.pdf" in the CDROM.

1

2

3

4

5

6

7

8

9

10

11

26

7 OSD (On-Screen Display)

1

2

OSD (On-Screen Display) means the operating menu displayed on the screen (hereinafter called OSD menu).

The OSD menu is operable by the wireless remote control or mouse.

OSD Operation

3

1.

When the [MENU] button on the wireless remote

 

control is pressed, a pointer is displayed.

 

 

 

2.

If the [MENU] button is pushed again, the OSD

4

 

menu is displayed, and the pointer moves to the

3.

lower left area of the OSD menu.

 

Move the pointer to the required icon. The pointer

 

 

can be moved by pushing the ARROW buttons.

5

 

(Same as MEMORY NO. buttons for image

 

memory/PRESET operation.)

 

4.

When the [MENU] button is pressed, the icon is

 

 

pressed and the corresponding operation is

6

 

executed.

5. To end the OSD menu, keep pushing the up/down

 

 

ARROW button to move the pointer out of the

 

 

OSD area. Then push the [MENU] button, and

7

 

the OSD menu goes off. If the [MENU] button is

 

pushed again, the pointer goes off.

remote control

CALL

SET IMAGE CALL

COLOR/B&W CONTRAST

LAMP

 

IMAGE ROTATION F.A.M.

ZOOM WIDE

NEAR FOCUS FAR

OPEN

CLOSE

AF

IRIS

 

 

Wireless remote control

MENU

IMAGE ROTATION F.A.M.

TELE ZOOM WIDE

NEAR FOCUS FAR

8

9

While the OSD menu is on the display, the pointer of the wireless remote control moves only on the icons in the OSD menu. (Color of icons is turned red).

If the sub-menu is displayed, the pointer moves only on the functional items. To move to another icon, close the sub-menu, and move the pointer.

When a pointer form is changed on the OSD menu, this setting is subsequently used.

10

27

Main Menu

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Icon

Name

Function

Reference Pages

 

 

 

 

Lamp

To turn ON/OFF the lighting.

 

P.17

 

 

 

 

 

When power is turned ON, the

 

 

 

 

 

 

 

previous saved setting remains.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Color/B&W

To switch the selection of the

 

P.19

 

 

 

 

selection

Color/B&W of the screen.

 

 

 

 

 

 

 

When power is turned ON, the

 

 

 

 

 

 

 

previous saved setting remains.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Posi/Nega

To switch the selection of the

 

P.20

 

 

 

 

conversion

positive/negative of the screen.

 

 

 

 

 

 

 

When power is turned ON, the

 

 

 

 

 

 

 

previous saved setting remains.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image rotation

To rotate the image

 

P.20

 

 

 

 

 

counterclockwise by 90°.

 

 

 

 

 

 

 

When power is turned ON, the

 

 

 

 

 

 

 

previous saved setting remains.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pause

To switch the selection of the

 

P.21

 

 

 

 

 

static/moving image.

 

 

 

 

 

 

 

When power is turned ON,

 

 

 

 

 

 

 

the initial state is Animation.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Aperture

To switch the modulation (edge

 

 

 

 

 

 

selection

emphasis) of the image.

 

 

 

 

 

 

 

When power is turned ON, the

 

 

 

 

 

 

 

previous saved setting remains.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pointer

To change the color and shape of

 

 

 

 

 

 

 

the pointer on the screen. Every

 

 

 

 

 

 

 

time the left button of the mouse

 

 

 

 

 

 

 

is clicked, the icon pointer is

 

 

 

 

 

 

 

switched in order of “[White arrow

 

 

 

 

 

 

 

→ Blue arrow → Yellow arrow →

 

 

 

 

 

 

 

Red arrow] → [White line → Blue

 

 

 

 

 

 

 

line → Yellow line → Red line]”.

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

5

6

7

8

9

10

11

28

1

2

3

4

5

6

7

8

9

10

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Icon

Name

Function

Reference Pages

 

 

 

 

 

Status saving

To save initial status when power

P.25

 

 

 

 

 

 

is turned ON.

 

 

 

 

 

 

 

 

 

 

 

 

 

For the mouse pointer ON/OFF

 

 

 

 

 

 

 

selection the same items stored in

 

 

 

 

 

 

 

the Preset/Move operation are

 

 

 

 

 

 

 

saved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Initialization

To reset this product to the

 

 

 

 

 

 

 

status of the factory settings.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Focus

To adjust the focus .

P.24

 

 

 

 

 

Near/Far

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Auto Focus

To focus automatically.

P.23

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zoom

To adjust the zoom of the lens.

P.17

 

 

 

 

 

Tele/Wide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Iris

To adjust the iris of the lens.

P.22

 

 

 

 

 

Close/Open

Auto/Manual selection

 

 

 

 

 

 

 

 

 

 

 

 

 

cannot be changed by

 

 

 

 

 

 

 

the OSD.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

29

Sub Menu

White Balance Adjustment

Gamma menu

Power Supply Off

menu

 

Timer

 

 

Icon

 

 

Name

Function

Reference Page

 

 

 

 

 

White Balance

To display the White Balance

 

 

 

 

 

 

 

 

 

 

 

Adjustment menu. When this

 

 

 

 

 

 

 

button is pressed again, the

 

 

 

 

 

 

 

White Blance Adjustment menu

 

 

 

 

 

 

 

is closed.

 

 

 

 

 

 

 

 

 

 

 

 

 

Auto

To set the White Blance in the

 

 

 

 

 

 

 

 

 

 

 

 

AUTO FOLLOW mode. (initial

 

 

 

 

 

 

 

setting)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

One-push

To set the push-set White

 

 

 

 

 

 

 

 

 

 

 

Blance. When this button is

 

 

 

 

 

 

 

pressed the white balance for

 

 

 

 

 

 

 

the then color temperature is

 

 

 

 

 

 

 

fixed.

 

 

 

 

 

 

 

 

 

 

 

 

 

Manual

To set the white balance with

 

 

 

 

 

 

 

<RED>, <GREEN> and

 

 

 

 

 

 

 

<BLUE>. Adjust the white

 

 

 

 

 

 

 

balance by pressing the mouse

 

 

 

 

 

 

 

button on the direction buttons

 

 

 

 

 

 

 

beside the volume bar.

 

 

 

 

 

 

 

<RED>…To adjust the red

 

 

 

 

 

 

 

component (01-99).

 

 

 

 

 

 

 

<GREEN>…To adjust the green

 

 

 

 

 

 

 

component (01-99).

 

 

 

 

 

 

 

<BLUE>…To adjust the blue

 

 

 

 

 

 

 

component (01-99).

 

 

 

 

 

 

 

 

 

1

2

3

4

5

6

7

8

9

10

11

30

1

2

3

4

5

6

7

8

9

10

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Icon

Name

Function

Reference Page

 

 

 

 

 

Gamma

To change the Gamma setting

 

 

 

 

 

 

adjustment

value (00(1.0) / 01(0.9) /

 

 

 

 

 

 

 

02(0.8) / 03(0.7) / 04(0.6) /

 

 

 

 

 

 

 

05(0.5) / 06(0.4) / 07(0.3)).

 

 

 

 

 

 

 

The factory setting is “04

 

 

 

 

 

 

 

(0.6).” Gamma cannot be

 

 

 

 

 

 

 

adjusted when the CONTRAST

 

 

 

 

 

 

 

is ON in the negative status.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power Supply

Sets the time between end of

 

 

 

 

 

 

Off Timer

operation and power OFF.

 

 

 

 

 

 

 

The time can be set within the

 

 

 

 

 

 

 

range from 01 (1h) to 08 (8h).

 

 

 

 

 

 

 

When 00 is set, the timer does

 

 

 

 

 

 

 

not operate.

 

 

 

 

 

 

 

If Power Supply is turned OFF,

 

 

 

 

 

 

 

the indicator LED turns orange.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

31

8 RS-232C SPECIFICATIONS

This product can be controlled by a PC connected through the RS-232C terminal [RS-232C].

Setting Up

(1)Connect this product to a PC with an RS-232C connection cable.

When using an RS-232C cable available in the market, select a cable with the connection shown below.

To protect this product and the PC, be sure to turn OFF all the power supply of all equipment before connecting.

(2)Start the PC, and set the communication mode of the RS-232C to the communication mode of this product.

For the information how to set the communication mode of the RS-232C, refer to the instruction manual of the PC.

(3)Start the PC program to operate this product.

(4)Control through the RS-232C will start.

For communication control, be sure to take the above steps for setting.

Cable Connection

 

Ceiling Presenter side

 

 

PC side

 

 

 

 

 

 

 

 

 

(DSUB-9P)

 

 

(DSUB-9P)

 

 

 

 

DSUB-9P (Female)

CD

1

1

CD

PC side :

 

 

 

DSUB-9P (Female)

 

 

 

 

 

RXD

2

2

RXD

5

4

3

2

1

5

4

3

2

1

TXD

3

3

TXD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DTR

4

4

DTR

 

 

 

 

 

 

 

 

 

 

SG

5

5

SG

 

 

 

 

 

 

 

 

 

 

DSR

6

6

DSR

 

 

 

 

 

9

 

8

7

6

RTS

7

7

RTS

 

9 8

7

 

6

 

CTS

8

8

CTS

 

 

 

 

 

 

 

RI (CI)

9

9

RI

 

 

 

 

 

1

2

3

4

5

6

7

8

9

10

11

32

Connection

1

If the RS-232C cable is not correctly connected between this product and the PC, no acknowledgement is transmitted. Connect the RS-232C cable correctly, and fix it firmly with

the connector set screws before the operation.

2

Transmission Specifications

3

 

• Full duplex start-stop sync. mode

 

 

• Start bit

: 1 bit

4

• Data bit

: 8 bits

• Stop bit

: 1 bit

 

• Parity bit

: None

 

• X parameter

: None

5

• Baud rate (Communication speed)

: 9600bps

 

 

6

Data Format Specifications

This command is executed in the form of 1-command/1 packet. The next command is not

 

 

accepted until the previous processing is completed.

7

• The communication command always starts with STX (Start of Text) , and ends with ETX

(End of Text) .

 

If the communication format or command name is wrong, NAK (Negative Acknowledgement) will be sent from this product.

When the communication format is correctly received, this product sends ACK (Normal

8 Acknowledgement).

Transmission command (PC Ceiling Presenter)

9

10

11

Each operation command is executed in ASCII code, and transmitted in a set of 7 bytes as follows:

 

S

 

 

 

 

 

E

 

Command

Parameter

Data

(PC)

T

T

(Ceiling Presenter)

X

 

 

 

 

 

X

 

 

 

 

 

→ ACK

 

 

 

 

 

 

33

Response data format (Ceiling PresenterPC)

All response data is transmitted as ASCII code, and it covers parameter of the table of operation command table.

• Status 0

 

S

Lamp

 

 

Posi /

Color

Pointer

Digital

Pause

Local

E

 

T

30H

 

T

 

on/off

 

Nega

/ B&W

display

Magnification

lockout

 

X

 

 

 

 

 

 

 

 

 

X

• Status 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S

 

 

 

 

 

 

 

 

30H

E

 

32H

γ

 

Image

Aperture

White

Contrast

30H

(Normal)

 

T

 

31H

T

 

X

 

adjustment

 

rotation

 

Balance

 

 

X

 

 

 

 

 

 

 

 

 

(Adjustment)

• Status 7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S

 

Iris

 

Power

 

 

 

 

20H

E

 

T

F.A.M.

 

supply

20H

20H

20H

20H

T

 

mode

 

 

X

 

 

off time

 

 

 

 

 

X

 

 

AUTO:31H

 

 

 

 

 

 

 

 

 

MANUAL:32H

 

 

 

 

 

 

• Status 8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S

Image

Image

 

Image

Image

Image

Image

Image

Image

E

 

T

 

T

 

memory8

memory7

memory6

memory5

memory4

memory3

memory2

memory1

 

X

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Byte not storing images is 30H.

Byte storing images is 31H.

Byte reading out images is 32H.

• ROM version

S

V

H

K

20H

 

 

E

T

56H

48H

4BH

 

 

T

X

 

 

 

X

 

 

 

 

 

 

 

 

 

 

 

ROM version 1

ROM version 2

1

2

3

4

5

6

7

8

9

10

11

34

1

2

3

4

5

6

7

8

9

10

11

UART Communication Format

Commands, parameters and data are all transmitted in ASCII code.

 

Function

Command

 

Parameter

Data

Comments

 

 

Auto Focus

AF

0

 

 

 

■ ■

 

 

 

Focus

FO

+

(NEAR)

■ ■

 

 

 

adjustment

 

(FAR)

 

 

 

 

 

 

0

(STOP)

 

 

 

 

Zoom

ZO

+

(TELE)

■ ■

 

 

 

adjustment

 

(WIDE)

 

 

 

 

 

 

0

(STOP)

 

 

 

 

Iris adjustment

IR

+

(OPEN)

■ ■

 

 

 

 

 

(CLOSE)

 

 

 

 

 

 

0

(STOP)

 

 

 

 

 

 

1

(AUTO)

 

 

 

 

 

 

2

(MANUAL)

 

 

 

 

Lamp

PL

0

(OFF)

■ ■

 

 

 

 

 

1

(ON)

 

 

 

 

Posi/Nega

NP

0

(POSI)

■ ■

 

 

 

 

 

1

(NEGA)

 

 

 

 

Color/B&W

CB

0

(COLOR)

■ ■

 

 

 

 

 

1

(B&W)

 

 

 

 

Pointer display

PO

0

(OFF)

■ ■

 

 

 

 

 

1

(ON)

 

 

 

 

Magnified

PM

0

(STOP)

■ ■

• When the pointer is ON:The pointer moves.

 

 

image move

 

1

( → )

 

• When the image magnification is ON.:

 

 

 

 

2

( ← )

 

The magnified image moves.

 

 

 

 

3

( ↑ )

 

 

 

 

 

 

 

4

( ↓ )

 

 

 

 

 

 

 

5

(

)

 

 

 

 

 

 

6

(

)

 

 

 

 

 

 

7

(

 

 

 

 

 

 

 

)

 

 

 

 

 

 

8

(

)

 

 

 

 

Digital

MA

0

(OFF)

■ ■

 

 

 

Magnification

 

1

(ON)

 

 

 

 

Pause

FZ

0

(OFF)

■ ■

 

 

 

 

 

1

(ON)

 

 

 

 

γ adjustment

GN

0

(γ = 1.0)

■ ■

 

 

 

 

 

1

(γ = 0.9)

 

 

 

 

 

 

2

(γ = 0.8)

 

 

 

 

 

 

3

(γ = 0.7)

 

 

 

 

 

 

4

(γ = 0.6)

 

 

 

 

 

 

5

(γ = 0.5)

 

 

 

 

 

 

6

(γ = 0.4)

 

 

 

 

 

 

7

(γ = 0.3)

 

 

 

 

Image Rotation

RO

0

(0°)

 

■ ■

 

 

 

 

 

1

(90°)

 

 

 

 

 

 

2

(180°)

 

 

 

 

 

 

3

(270°)

 

 

 

 

Aperture

AP

0

(OFF)

■ ■

 

 

 

selection

 

1

(ON)

 

 

 

 

White Balance

AW

0

(OFF)

■ ■

 

 

 

selection

 

1

(AUTO)

 

 

 

 

 

 

2

(ONE-PUSH)

 

 

 

35

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Function

Command

 

Parameter

Data

Comments

 

 

 

 

F.A.M.

CL

0 (OFF)

■ ■

 

 

 

 

 

selection

 

1

(ON)

 

 

 

 

 

 

Image Store

IS

1

 

■ ■

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

Image Read

IC

1

 

■ ■

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

Image Switch

AV

0

 

■ ■

• To finish the IMAGE CALL mode and go

 

 

 

 

 

 

 

 

 

back to the normal camera image.

 

 

 

 

Contrast

CT

0 (OFF)

■ ■

 

 

 

 

 

 

 

1

(ON)

 

 

 

 

 

 

Local Lockout

LL

0 (OFF)

■ ■

 

 

 

 

 

 

 

1

(ON)

 

 

 

 

 

 

Default

DF

0

 

■ ■

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Status request

QS

0

 

■ ■

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

Rom version

QR

0

 

■ ■

 

 

 

 

 

ACK check

SA

0 (OFF)

■ ■

 

 

 

 

 

 

 

1

(ON)

 

 

 

 

 

 

CR addition

SC

0 (OFF)

■ ■

 

 

 

 

 

 

 

1

(ON)

 

 

 

 

 

 

Power Supply

PW

0 (OFF)

■ ■

 

 

 

 

 

Off Timer

 

1

(1 hour)

 

 

 

 

 

 

 

 

2

(2 hours)

 

 

 

 

 

 

 

 

3

(3 hours)

 

 

 

 

 

 

 

 

4

(4 hours)

 

 

 

 

 

 

 

 

5

(5 hours)

 

 

 

 

 

 

 

 

6

(6 hours)

 

 

 

 

 

 

 

 

7

(7 hours)

 

 

 

 

 

 

 

 

8

(8 hours)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power Supply

DN

0 (OFF)

■ ■

 

 

 

 

 

 

 

1 (ON)

 

 

 

 

 

 

 

 

 

 

 

 

 

"■ ■" in the data column means that the SPACE [20H] should be transmitted twice.

1

2

3

4

5

6

7

8

9

10

11

36

9 REPLACING THE LAMP

1

Replacing the Lamp

The lamp that is installed in the product has a certain life span. When the lamp is used for a 2 long period, the lamp light may become dark or the lamp may go off due to the end of its life.

(The life of the lamp varies according to the utilization condition.) In this case, replace the lamp.

3

4

5

How to replace the lamp

 

 

 

 

 

WARNING

 

• Use JR12V50W AKM/5EZ-1 manufactured by Phillips for

 

 

replacement. Other lamps may blow out or cause fire if used.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• The lamp is very hot immediately after use. Direct contact

 

 

 

with the lamp or lamp cover will cause burns. Make sure that

 

CAUTION

 

lamp is thoroughly cooled off (30 minutes or more) before

 

 

replacing the lamp.

 

 

 

 

 

 

• Replacement of the lamp requires a work done at a high

 

 

 

location. Take care not to cause accident.

 

 

 

 

 

 

 

 

 

 

 

 

6

1.Turn OFF the Power Supply Switch.

2.Remove the power cord.

7

3.Wait until the lamp is thoroughly cooled off.

4.Remove the lamp cover.

8

 

Loosen the fixing screws and displace the lamp

 

 

cover in the arrow direction. (Fig. 1)

 

 

Turn the lamp cover around the fixing screw.

9

 

(Fig. 2)

5.

Replace the lamp.

 

 

 

Rotate the lamp and install a new lamp.

10

6.

Install the lamp cover.

Lamp cover shall be installed in sequence reverseto its removal.

11

REQUEST

screw

( Fig. 1)

( Fig. 2)

Since the lamp is made of glass, do not touch the glass surface with bare hands, apply a strong impact, or scratch the surface.

37

10 TROUBLESHOOTING HINTS

Symptoms and Confirmation

Check the following items. If any abnormality is found, consult the seller or our branch/office in your area.

 

Symptom

Possible cause / countermeasure

 

 

No image on TV

• Cable is not properly connected to the video-in terminal of monitor.

 

 

monitor.

• The power cord is disconnected from the wall AC outlet.

 

 

 

• The plug is disconnected from the power cord receptacle of this product.

 

 

 

• The power switch is not turned ON.

 

 

 

• Zoom is set at TELE to display only white/black part of the

 

 

 

material.

 

 

 

• The power switch is turned ON immediately after it is turned OFF.

 

 

 

In this case, this product may not start. Wait several seconds after

 

 

 

turning OFF the power switch, and then turn ON the power switch.

 

 

 

 

 

 

Out of focus

•The object is too close to the lens.

 

 

 

Check it the object is not placed at a distance shorter than 1.3m

 

 

 

(51.2 in.) from the unit.

 

 

 

• FOCUS is set at the extreme position of WIDE and the picture is

 

 

 

zoomed to TELE. FOCUS at the extreme position of TELE and zoom

 

 

 

the picture to WIDE.

 

 

 

• Focusing is sometimes difficult in the AUTO FOCUS mode.

 

 

 

 

 

 

Image oscillates.

• If image oscillates widely at TELE position or in the digital

 

 

 

magnification, vibration of the building could affect the event.

 

 

 

By pushing the [PAUSE] button on the wireless remote control,

 

 

 

image oscillation is alleviated by displaying still image.

 

 

 

 

 

 

Video output image

• Is the video output type set to PAL?

 

 

is disarrayed.

If this product which is set to PAL is connected to the monitor

 

 

 

specially designed for NTSC, the video image may not be output

 

 

 

normally, in which the image is disarrayed, or becomes black

 

 

 

and white.

 

 

 

Switch the video output type by referring to P. 9 "DIP Switches."

 

 

 

 

 

 

Image is too dark.

• The intensity of illumination is not sufficient.

 

 

 

Turn ON the lamp by pressing the [LAMP] button on the wireless

 

 

 

remote control.

 

 

 

• If the distance from this product to a manuscript is long, illuminate

 

 

 

the surface of specimen brighter by using external lighting.

 

 

 

• Is the iris adjusted to "Close" side? Adjust the iris to "Open" side.

 

 

The image is striped.

• This may be interference fringes between dots of printed matter

 

 

 

and TV scanning lines or CCD pixels, which may be mitigated by

 

 

 

changing the projection range.

 

 

 

• When using an LCD projector, vertical stripes may appear on the

 

 

 

screen. This may be mitigated by manually adjusting the dot clock

 

 

 

frequency on the projector side (refer to P. 15).

 

 

 

 

 

 

Brightness tone is out

• This may be mitigated by switching the Gamma setting.

 

 

of order.

 

 

 

 

 

 

1

2

3

4

5

6

7

8

9

10

11

38

1

2

3

4

5

6

7

8

9

10

11

11SPECIFICATIONS

General

Item

 

Specifications

 

Power source

AC100 - 240V 50Hz/60Hz

 

Rated current

1.2 - 0.6A

 

 

Dimensions

226mm × 226mm × 239mm (8.9 × 8.9 × 9.4 in.)

 

(W × D × H)

 

 

 

 

 

 

Weight

6.5 kg (14.3 lbs.) (main body only)

 

Output terminal

RGB output

Mini DSUB 15P connector, female

×1

 

Composite Video output

RCA pin jack/75Ω unbalanced (NTSC/PAL)

×1

 

S-Video output

Mini DIN 4P connector/75Ω unbalanced (NTSC/PAL)

×1

Ext. control

RS-232C

DSUB 9P connector, male

×1

terminal

Mouse

Mini DIN 6P connector, female

×1

 

USB

Type B receptacle

×1

39

Camera

Item

 

Specifications

Lens

f = 14.2 – 170mm (12 - time zoom), F2.6 – 2.7

Frame rate

20 frames / sec

 

Shooting area(H × V)

662mm × 511mm (26.0 × 20.1 in.) max.

(Projection -> photographing

53mm × 41mm (2.1 × 1.6 in.) min.

distance: 2m(78.7in))

 

 

Limit of focus

Distance from the unit to the text (object of shooting):

adjustment

 

 

 

 

Zooming

Electromotive (with double speed function)

Focusing

Auto / Manual

 

Iris

Auto (level adjustable) Manual (RS-232C)

Image pick-up device

1/3″ CCD

 

Total pixels

1077(H) × 788(V), 850,000 pixels

Effective pixels

1034(H) × 779(V)

 

Sync. system

Internal sync.

 

Resolution

Analog RGB output : Horizontal 600TV lines or more;

 

 

Vertical 600TV lines or more

 

Video output :

Horizontal 400 TV lines or more

Analog RGB

0.7V (p-p) 75Ω unbalanced, synchronization signal, positive polarity

output

Signal frequency

 

 

XGA: Horizontal frequency 48.363 kHz;

 

Vertical frequency 60.004 Hz (1024 × 768 at 60 Hz);

 

Compliant with VESA

 

Composite Video output

NTSC/PAL

 

S-Video output

NTSC/PAL

 

White Balance

Full auto / One-push / Manual

Video outputt selectionl ti

Provided (NTSC / PAL)

Posi/Nega conversion

Provided

 

Color/B&W selection

Provided

 

Image Rotation

Provided (0° / 90° / 180° / 270°)

Contrast

Provided

 

Gamma selection

Provided (1.0 / 0.9 / 0.8 / 0.7 / 0.6 / 0.5 / 0.4 / 0.3)

Aperture selection

Provided

 

Pause

Provided

 

Digital magnification

Provided (double, can be scrolled)

Pointer

Controllable (color selectable)

F.A.M. selection

Provided

 

Lighting

Item

Specifications

Lamp

Halogen lamp 12V 50W

 

(model: JR12V50W AKM/5EZ-1 manufactured by Phillips)

 

 

1

2

3

4

5

6

7

8

9

10

11

40

1

2

3

4

5

6

7

8

9

10

11

Supplied Accessories

Name

Quantity

Power cord (2.5m)

1

Video cable (RCA pin connector) (3 m)

1

S-Video cable (Mini DIN 4P connector) (2 m)

1

Infrared wireless remote controller (RCW-C1000)

1

Batteries (Type R03, AAA)

2

Analog RGB cable (DSUB 15P connector) (2 m)

1

Analog RGB cable (BNC connector) (1.8 m)

1

Instruction manual

1

Installation manual

1

Warranty card

1

Scroll mouse

1

USB cable (1.8m)

1

Utility Software CD-ROM

1

Utility Software Installation Manual

1

C. Mounting fitting

1

Attaching screw (M4x10)

3

Attaching screw (M5x10)

4

Optional parts (to be purchased separately)

Halogen lamp ( JR12V50W AKM/5EZ-1)

Ceiling - mounting fitting VB-1000

For the RCA pin, use a pin plug compliant with RC-6703.

The above specifications are subject to change without notice.

Trademark Acknowledgements

VESA is a registered trademark of Video Electronics Standards Association.

VGA, SVGA, XGA and SXGA are trademarks or registered trademarks of International Business Machines Corporation.

and , VISUAL PRESENTER, FOCUSFREE are trademarks of ELMO Co., Ltd.

41

[MEMO]

 

 

copyrighted

slide

films,

photographs, etc.

may

infringe

of

copyright

owners and

to

copyright

laws.

 

 

 

 

 

 

 

ELMO CO., LTD.

6-14, Meizen-cho, Mizuho-ku,

Nagoya, 467-8567, Japan

OVERSEAS SUBSIDIARY COMPANIES

U.S.A.

ELMO Mfg. Corp.

 

 

1478 Old Country Road, Plainview, NY 11803-5034

 

Tel:(516)501-1400

Fax:(516)501-0429

 

E-mail: elmo@elmousa.com

 

Web: http://www.elmousa.com/

Canada

ELMO Canada Mfg. Corp.

 

44 West Drive, Brampton, Ontario L6T 3T6

 

Tel:(905)453-7880

Fax:(905)453-2391

 

E-mail: info@elmocanada.com

 

Web: http://www.elmocanada.com/

Germany

ELMO (Europe) G.m.b.H.

 

Neanderstr. 18, 40233 Düsseldorf

 

Tel:(0211)376051

Fax:(0211)376630

 

E-mail: elmoeurope@AOL.com

 

Web: http://www.elmo.de/

 

Printed in Japan

Printed on recycled paper

6X1VHK002