Preface
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
TrademarkRecognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation.
Other product names used in this manual are the properties of their respective owners and are acknowledged.
FederalCommunicationsCommission(FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and the receiver
•Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected
•Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.
H81H3-M3S USER MANUAL
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:
•This device may not cause harmful interference, and
•This device must accept any interference received, including interference that may cause undesired operation.
This device is in conformity with the following EC/EMC directives:
EN 55022
EN 61000-3-2
EN 61000-3-3
EN 55024
EN 60950
CE marking
Limits and methods of measurement of radio disturbance characteristics of information technology equipment
Disturbances in supply systems caused
Disturbances in supply systems caused by household appliances and similar electrical equipment “ Voltage fluctuations”
Information technology equipment-Immunity characteristicsLimits and methods of measurement
Safety for information technology equipment including electrical business equipment
CanadianDepartmentofCommunications
This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.
AbouttheManual
The manual consists of the following:
Chapter 1 |
Describes |
features |
of |
the |
page 1 |
Introducing the Motherboard |
motherboard. |
|
|
|
|
Chapter 2 |
Describes |
installation |
of |
page 7 |
|
Installing the Motherboard |
motherboard components. |
|
|||
Chapter 3 |
Provides information on us- |
page 25 |
|||
Using BIOS |
ing the BIOS Setup Utility. |
|
|||
Chapter 4 |
Describes the motherboard |
page 63 |
|||
Using the Motherboard Software software. |
|
|
|
|
|
Chapter 5 |
Provides |
basic |
trouble |
page 67 |
|
Trouble Shooting |
shooting tips. |
|
|
|
|
H81H3-M3S USER MANUAL
ii
TABLE OF CONTENTS |
|
Preface |
i |
Chapter 1 |
1 |
Introducing the Motherboard |
1 |
Introduction................................................................................... |
1 |
Pakage Contents............................................................................ |
1 |
Specifications................................................................................ |
2 |
Motherboard Components.......................................................... |
4 |
I/O Ports.............................................................................................. |
6 |
Chapter 2 |
7 |
Installing the Motherboard |
7 |
Safety Precautions............................................................................. |
7 |
Installing the Motherboard in a Chassis...................................... |
7 |
Checking Jumper Settings................................................................. |
8 |
Installing Hardware.................................................................. |
9 |
Installing the Processor............................................................. |
9 |
Installing the CPU Cooler......................................................... |
11 |
Installing Memory Modules.................................................... |
12 |
Installing Add-on Cards........................................................... |
13 |
Connecting Optional Devices.................................................. |
15 |
Installing a SATA Hard Drive................................................... |
20 |
Connecting Case Components....................................................... |
21 |
Front Panel Header................................................................. |
23 |
Chapter 3 |
25 |
Using BIOS |
25 |
About the Setup Utility................................................................ |
25 |
The Standard Configuration.................................................... |
25 |
Entering the Setup Utility........................................................ |
25 |
Resetting the Default CMOS Values..................................... |
26 |
Using BIOS........................................................................................ |
26 |
BIOS Navigation Keys..............................................................27 |
|
Main Menu............................................................................. |
28 |
Advanced Menu...................................................................... |
29 |
Chipset Menu.......................................................................... |
44 |
M.I.B III(MB Intelligent Bios III) Menu.................................... |
51 |
Boot Menu............................................................................... |
59 |
Security Menu.......................................................................... |
60 |
Exit Menu................................................................................ |
61 |
H81H3-M3S USER MANUAL
iii
Chapter 4 |
63 |
Using the Motherboard Software |
63 |
Auto-installing under Windows XP/7/8...................................... |
63 |
Running Setup......................................................................... |
63 |
Manual Installation.......................................................................... |
65 |
Chapter 5 |
67 |
Trouble Shooting |
67 |
Start up problems during assembly.............................................. |
67 |
Start up problems after prolong use............................................ |
68 |
Maintenance and care tips.............................................................. |
68 |
Basic Troubleshooting Flowchart................................................... |
69 |
H81H3-M3S USER MANUAL
iv
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the H81H3-M3S motherboard. This motherboard is a high performance, enhanced function motherboard designed to support the LGA1150 socket for latest 4th Generation Intel→ CoreTM Family/Pentium→ Celeron→ processors for high-end business or personal desktop markets.
This motherboard is based on Intel→ H81 Express Chipset for best desktop platform solution. H81 is a single-chip, highly integrated, high performance Hyper-Threading peripheral controller, unmatched by any other single chip-device controller. This motherboard supports up to 16 GB of system memory with DDR3 1600 SDRAM. High resolution graphics via PCI Express x16 slot, intended for Graphics Interface, is fully compliant to the PCI Express Base Specification revision 2.0. It provides two PCI rev 2.2 slots and one PCI Express x1 rev 2.0 slot for extending usage.
It implements an EHCI (Enhanced Host Controller Interface) compliant interface that provides six USB 2.0 ports (two USB 2.0 ports at the back panel and two USB 2.0 headers support additional four USB 2.0 ports, please refer to chapter 2 parts of Front Panel USB headers for more details). This motherboard implements two USB 3.0 ports at rear I/O with blue connectors also.
The motherboard is equipped with advanced full set of I/O ports in the rear panel, including PS/2 mouse and PS/2 keyboard connectors, one LPT port , one COM port, one VGA port, one HDMI port,one RJ45 LAN connector, two USB 2.0 ports, two USB 3.0 ports (USB 2.0 optional), and audio jacks 6-ch for microphone, line-in and line-out.
In addition, this motherboard supports two SATA 3Gb/s and two SATA 6Gb/s connectors for expansion.
Package Contents
Your motherboard package ships with the following items:
H81H3-M3S Motherboard
User Manual
DVD
I/O Shield
2 SATA 6Gb/s Cables
The package contents above are for reference only, please take the actual package items as standard.
Chapter 1
H81H3-M3S USER MANUAL
1
1 Chapter
Specifications
CPU |
• |
LGA1150 socket for latest 4th Generation Intel→ CoreTM Family |
|
|
/Pentium→/Celeron→ processors |
|
• |
Supports “Hyper-Threading” technology CPU |
|
Note: Please go to ECS website for the latest CPU support list. |
|
|
|
|
Chipset |
• |
Intel→ H81 Chipset |
Memory |
• |
DDR3 memory architecture |
|
• |
2 x 240-pin DDR3 DIMM sockets support up to 16 GB |
|
• |
Supports Dual DDR3 1600 MHz DDR3 SDRAM |
|
Note: Please go to ECS website for the latest Memory support list. |
|
|
|
|
Expansion |
• |
1 x PCI Express x16 Gen2 slot |
Slots |
• |
1 x PCI Express x1 Gen2 slot |
|
• |
2 x PCI slots |
Storage |
• |
Supported by Intel→ H81 Express Chipset |
|
|
2 x Serial ATA 3Gb/s devices |
|
|
2 x Serial ATA 6Gb/s devices |
Audio |
• |
Realtek ALC662 6-Ch HD audio CODEC |
|
• |
Compliant with HD audio specification |
|
|
|
LAN |
• |
Realtek RTL8111G Gigabit Lan |
|
|
|
Rear Panel I/O |
• |
1 x PS/2 keyboard and PS/2 mouse connectors |
|
• |
1 x LPT port |
|
• |
1 x VGA port |
|
• |
1 x COM port |
|
• |
1 x HDMI port |
|
• |
2 x USB 2.0 ports |
|
• |
1 x RJ45 LAN connector |
|
• |
2 x USB 3.0 ports (USB 2.0 optional) |
|
• |
Audio jacks 6-ch for microphone, line-in and line-out |
|
|
|
Internal I/O |
• |
1 x 24-pin ATX Power Supply connector |
Connectors & |
• |
1 x 4-pin 12V Power connector |
Headers |
• |
1 x 4-pin CPU_FAN connector |
|
• |
1 x 4-pin SYS_FAN connector |
|
• |
1 x Front Panel audio header |
|
• |
1 x Front Panel switch/LED header |
|
• |
1 x ME_UNLOCK header |
|
• |
2 x USBPWR_R headers |
|
• |
1 x USBPWR_F headers |
|
• |
2 x Serial SATA 3Gb/s connectors |
|
• |
2 x Serial SATA 6Gb/s connectors |
|
• |
2 x USB 2.0 headers support additional four USB 2.0 ports |
|
• |
1 x Case open header |
|
• |
1 x TPM_TCM header (TPM or TCM by optional) |
|
• |
1 x Serial port header (COM) |
|
• |
1 x CLR_CMOS header |
|
|
|
H81H3-M3S USER MANUAL
2
|
|
|
|
1 |
System BIOS |
• |
AMI BIOS with 64Mb SPI Flash ROM |
|
|
|
Chapter |
|||
|
• |
F7 hot key for boot up devices option |
|
|
|
• |
Supports Plug and Play, STR (S3)/STD (S4), Hardware monitor, |
|
|
|
|
Multi Boot |
|
|
|
• |
Supports ACPI & DMI |
|
|
|
• |
Audio, LAN, can be disabled in BIOS |
|
|
|
• |
Support PgUp clear CMOS Hotkey (Has PS2 KB Model only) |
|
|
|
|
|||
|
|
|
|
|
Form Factor |
• |
Micro-ATX Size, 244mm x 180mm |
|
|
|
|
|
|
|
H81H3-M3S USER MANUAL
3
1 Chapter
Motherboard Components
H81H3-M3S USER MANUAL
4
Table of Motherboard Components
|
LABEL |
COMPONENTS |
|
1. CPU Socket |
LGA1150 socket for latest 4th Generation Intel® Core™ |
|
Family/ Pentium®/Celeron® Processors |
|
|
|
|
|
2. CPU_FAN |
4-pin CPU cooling fan connector |
|
3. DDR3_1~2 |
240-pin DDR3 SDRAM slots |
|
4. ATX_POWER |
Standard 24-pin ATX power connector |
|
5. SATA1~2 |
Serial ATA 6.0 Gb/s connectors |
|
6. SATA3~4 |
Serial ATA 3.0 Gb/s connectors |
|
7. USBPWR_F1 |
Front panel USB power select jumper |
|
8. CLR_CMOS |
Clear CMOS jumper |
|
9. F_PANEL |
Front panel switch/LED header |
|
10. CASE |
CASE open header |
|
11. ME_UNLOCK |
ME unlock header-for factory use only |
|
12. F_USB1~2 |
Front panel USB 2.0 headers |
|
13. TPM_TCM |
Trusted Platform Module header |
|
14. COM2 |
Onboard serial port header |
|
15. F_AUDIO |
Front panel audio header |
|
16. PCI1~2 |
32-bit add-on card slots |
|
17. PCIE1 |
PCI Express x1 slot |
|
18. PCIEX16 |
PCI Express slot for graphics interface |
|
19. SYS_FAN |
4-pin system cooling fan connector |
|
20. USBPWR_R1~2 |
Rear panel USB power select jumpers |
|
20. ATX12V |
4-pin +12V power connector |
|
|
|
Chapter 1
H81H3-M3S USER MANUAL
5
1 Chapter
I/O Ports
1. PS/2 Mouse(green)
Use the upper PS/2 port to connect a PS/2 mouse.
2. PS/2 Keyboard(purple)
Use the lower PS/2 port to connect a PS/2 keyboard.
3. LPT Port
Use the LPT port to connect printers or other parallel communication devices.
4. COM1 Port
Use the COM1 port to connect the serial devices such as mice or fax/modems.
5. VGA Port
You can connect the display device to the VGA port.
6. USB 3.0 Ports
Use the USB 3.0 ports to connect USB 3.0 devices.
7. HDMI Port
You can connect the display device to the HDMI port.
8. LAN Port
Connect an RJ-45 jack to the LAN port to connect your computer to the Network.
LAN LED |
Status |
Description |
|
|
|
|
|
|
|
|
|
Link LED |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Activity LED |
OFF |
No data |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Orange blinking |
Active |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Link LED |
OFF |
No link |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Green |
Link |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LAN Port |
|||||||||||||
|
|
|
|
|
||||||||||||
9. USB 2.0 Ports
Use the USB 2.0 ports to connect USB 2.0 devices.
10. Line-in(blue)
It can be connected to an external CD/DVD player, Tape player or other audio devices for audio input.
11. Line-out(lime)
It is used to connect to speakers or headphones.
12. Microphone(pink)
It is used to connect to a microphone.
H81H3-M3S USER MANUAL
6
Chapter 2
Installing the Motherboard
2-1. Safety Precautions
Follow these safety precautions when installing the motherboard: |
2 |
|
• |
Wear a grounding strap attached to a grounded device to avoid damage |
Chapter |
• |
Leave components in the static-proof bags. |
|
|
from static electricity. |
|
• |
Discharge static electricity by touching the metal case of a safely grounded |
|
|
object before working on the motherboard. |
|
• |
Always remove the AC power by unplugging the power cord from the power |
|
|
||
|
outlet before installing or removing the motherboard or other hardware |
|
|
components. |
|
2-2. Installing the motherboard in a Chassis
This motherboard carries a Micro ATX form factor of 244 x 180 mm. Choose a chassis that accommodates this form factor. Make sure that the I/O template in the chassis matches the I/O ports installed on the rear edge of the motherboard. Most system chassis have mounting brackets installed in the chassis, which corresponds to the holes in the motherboard. Place the motherboard over the mounting brackets and secure the motherboard onto the mounting brackets with screws.
Do not over-tighten the screws as this can stress the motherboard.
H81H3-M3S USER MANUAL
7
2-3. Checking Jumper Settings
The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.
2 Chapter
To avoid the system instability after clearing CMOS, we recommend users to enter the main BIOS setting page to “Load Default Settings” and then “Save and Exit Setup”.
H81H3-M3S USER MANUAL
8
2-4. Installing Hardware
2-4-1. Installing the Processor
• |
This motherboard has an LGA1150 socket. |
|
• |
When choosing a processor, consider the performance requirements of |
|
|
the system. Performance is based on the processor design, the clock speed |
|
|
2 |
|
|
and system bus frequency of the processor, and the quantity of internal |
|
|
cache memory and external cache memory. |
Chapter |
• |
You may be able to change the settings in the system Setup Utility. We |
|
|
strongly recommend you do not over-clock processor or other |
|
|
components to run faster than their rated speed. |
|
• |
The following illustration shows CPU installation components. |
|
|
A. Press the hook of lever down with your thumb and pull it to the right |
|
|
side to release it from retention tab. |
|
B. Lift the tail of the load lever and rotate the load plate to fully open position.
C. Grasp the edge of the package substrate. Make sure pin 1 indicator is on your bottom-left side. Aim at the socket and place the package carefully into the socket by purely vertical motion.
H81H3-M3S USER MANUAL
9
D. Rotate the load plate onto the package IHS (Intergraded Heat Spreader). Engage the load lever while pressing down lightly onto the load plate. Secure the load lever with the hook under retention tab. Then the cover will flick automatically.
2 Chapter
Please save and replace the cover onto the CPU socket if processor is removed.
H81H3-M3S USER MANUAL
10
2-4-2. Installing the CPU Cooler
• |
Install the cooling fan in a well-lit work area so that you can clearly see the |
|
|
motherboard and processor socket. |
|
• |
Avoid using cooling fans with sharp edges in case the fan casing and the |
|
|
clips cause serious damage to the motherboard or its components. |
|
• |
To achieve better airflow rates and heat dissipation, we suggest that you |
|
|
use a high quality fan with 3800 rpm at least. CPU fan and heat sink |
2 |
|
installation procedures may vary with the type of CPU fan/heatsink |
Chapter |
|
supplied. The form and size of fan/heatsink may also vary. |
|
|
|
|
• |
DO NOT remove the CPU cap from the socket before installing a CPU. |
|
• |
Return Material Authorization (RMA) requests will be accepted only if the |
|
|
motherboard comes with the cap on the LGA1150 socket. |
|
• |
The following illustration shows how to install CPU fan. |
|
|
||
|
A. Apply some thermal grease onto the contacted area between the |
|
|
heatsink and the CPU, and make it to be a thin layer. |
|
B. Fasten the cooling fan supporting base onto the CPU socket on the motherboard. And make sure the CPU fan is plugged to the CPU fan connector.
C. Connect the CPU cooler power connector to the CPU_FAN connector.
H81H3-M3S USER MANUAL
11
2-4-3. Installing Memory Modules
2 Chapter
•This motherboard accommodates two memory modules. It can support two 240-pin DDR3 1600.
•Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.
•You must install at least one module in any of the two slots. Total memory capacity is 16 GB.
•Refer to the following to install the memory modules.
A. Push the latches on each side of the DIMM slot down.
B. Install the DIMM module into the slot and press it firmly down until it seats correctly. Check that the cutouts on the DIMM module edge connector match the notches in the DIMM slot.
C. The slot latches are levered upwards and latch on to the edges of the DIMM.
H81H3-M3S USER MANUAL
12
2-4-4. Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.
Chapter 2
PCIEX16 Slot
PCIE1 Slot
PCI1~2 Slots
The PCI Express x16 slot is used to install an external PCI Express graphics card that is fully compliant to the PCI Express Base Specification revision 2.0.
The PCI Express x1 slot is fully compliant to the PCI Express Base Specification revision 2.0.
This motherboard is equipped with two standard PCI slots. PCI stands for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus standard. The PCI slots on this board are PCI v2.2 compliant.
Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.
H81H3-M3S USER MANUAL
13
Follow these instructions to install an add-on card:
1Remove a blanking plate from the system case corresponding to the slot you are going to use.
2Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot.
2 Chapter
3Secure the metal bracket of the card to the system case with a screw.
1.For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.
2.The onboard PCI interface does not support 64-bit SCSI cards.
Please refer the following illustrations to install the add-on card:
Install the VGA Card in the PCI slot |
Install the LAN Card in the PCIE1 slot |
Install the VGA Card in the PCIEX16 slot
H81H3-M3S USER MANUAL
14
2-4-5. Connecting Optional Devices
Refer to the following for information on connecting the motherboard’s optional devices:
Chapter 2
No. |
Components |
No. |
Components |
1 |
SATA3_1~2 |
5 |
F_USB1~2 |
2 |
SATA2_3~4 |
6 |
TPM_TCM |
3 |
CASE |
7 |
COM2 |
4 |
ME_UNLOCK |
8 |
F_AUDIO |
1 & 2. SATA3_1~2 & SATA2_3~4: Serial ATA Connectors
SATA3_1~2 connectors are used to support the Serial ATA 6Gb/s device, and SATA2_3~4 connectors are used to support the Serial ATA 3Gb/s device, simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.
H81H3-M3S USER MANUAL
15
3. CASE: Chassis Intrusion Detect Header
This detects if the chassis cover has been removed. This function needs a chassis equipped with instrusion detection switch and needs to be enabled in BIOS.
2 Chapter
4. ME_UNLOCK: ME Unlock Header
H81H3-M3S USER MANUAL
16
5. F_USB1~2: Front Panel USB 2.0 Headers
The motherboard has two USB 2.0 headers supporting four USB 2.0 ports. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.
Chapter 2
Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hang-up.
6. TPM_TCM:Trusted Platform Module Header/ Terminal To ComputerMultiplexer (Optional)
Trusted platform module(TPM) is a published specification detailing a microcontroller that can store secured information, and implementations of that specification.
H81H3-M3S USER MANUAL
17
7. COM2: Onboard Serial Port Header
Connect a serial port extension bracket to this header to add a serial port to your system.
2 Chapter
8. F_AUDIO: Front Panel Audio Header
The front panel audio header allows the user to install auxiliary front-oriented microphone and line-out ports for easier access. This header supports HD audio by default. If you want connect an AC’ 97 front panel audio to HD onboard headers, please set as below picture.
AC’ 97 Audio Configuration: To enable the front panel audio connector to support AC97 Audio mode.
If you use AC’ 97 Front Panel, please tick off the option of “Disabled Front Panel Detect ”. If you use HD Audio Front Panel, please don’ t tick off “Disabled Front Panel Detect ” .
H81H3-M3S USER MANUAL
18
Chapter 2
* For reference only
If you use AC’ 97 Front Panel, please don’ t tick off “Using Front Jack Detect ”. If you use HD Audio Front Panel, please tick off the option of “Using Front Jack Detect ”.
* For reference only
H81H3-M3S USER MANUAL
19
Loading...