DBetriebsanleitung Systemkreissäge
PK 255
G Operating Instruction
System circular saw
F Instructions d'utilisation
Scie circuaire à système
0
5
10
15
20
25
30
35
D
G
F
Deutschland
Great Britain
France
Die beiliegende Garantiekarte senden Sie bitte an uns zurück.
Den Kaufbeleg bitte aufbewahren! Ein Anspruch auf Garantieleistungen besteht nur gegen Vorlage des Kaufbelegs.
Die Adresse Ihrer nächstgelegenen Werksvertretung finden Sie auf der hinteren Umschlagseite.
Please return the enclosed warranty card to us.
Retain proof of purchase! You are only entitled to claim warranty against proof of purchase.
Please see back cover for manufacturer representative´s address nearest you.
SVP, retournez-nous la carte de garantie jointe.
Conservez le reçu d'achat! La garantie ne peut être accordée que sur présentation de ce reçu.
Vous trouverez l'adresse de votre représentant le plus proche à la dernière page de couverture.
1.
2.
3.
1
2
0
5
10
15
20
25
30
35
6
3
5
1System circular saw with saw blade
2Blade guard hardware bag
3Rip fence with auxiliary fence extrusion
4Push stick / feeding aid
5Leg with foot (4x)
6Connector suction hose / chip case
4
PK 255 |
2.1 |
3
4
2
5
1
0
5
10
15
20
25
30
35
6
7
8
9
10
1Saw blade
2Riving knife
3Blade guard
4Rip fence with auxiliary fence extrusion
5Push stick / feeding aid
6Handwheel with lock lever for blade tilt setting
7Handwheel for depth of cut setting
8On/off switch with emergency stop
9Mains connection
10 Legs
2.2 |
PK 255 |
∙Read these instructions before commissioning. Pay special attention to the safety information.
∙If you notice a transport damage while unpacking, notify your supplier immediately. Do not operate the machine!
∙Dispose of the packing environmentally friendly. Bring to a proper collecting point.
∙Keep these instructions for reference on any issues you may be uncertain about.
∙If you lend or sell this machine be sure to have the instructions to go with it.
This machine is intended for ripping and crosscutting of solid timber, faced board, particle board, wood-core plywood and similar wood-derived materials.
Do not cut round stock without a suitable fixture, as the rotating saw blade could turn the workpiece.
Any other use is considered to be not as specified and not allowed. Damages caused by unspecified use are not covered by the manufacturer's liability.
Modification of the machine or use of parts not tested and approved by the equipment manufacturer can cause unforeseeable damage.
Follow the basic safety requirements for the operation of power tools, to keep the risk of
−personal injury
−fire
−electric shock
as little as possible.
Please note in particular:
A circular saw is a dangerous tool which can, due to operator carelessness, cause serious personal injury. It is therefore recommended you follow the safety information given below, and know and follow the legal regulations pertaining to the operation of circular saws.
ADanger!The circular saw shall only be started and operated by persons familiar with circular saws, and who are at any time aware of the dangers associated with the operation of such tool.
Persons under 16 years of age shall use this saw only under the supervision of an instructor in the course of their vocational training.
The following residual risks do principally exist with circular saws, and can not, even by employing safety devices, completely eliminated:
−Risk of injury by touching the revolving saw blade: Keep sufficient distance to the saw blade when sawing. Use push stick if necessary.
Prevent adverse body positions. Ensure firm footing, and keep your balance at all times.
−Risk of injury by touching the saw blade at standstill: Lower the saw blade after sawing until the blade guards rest on the table. Wear gloves when changing blades.
−Hazard by cluttered work area (e.g. by cutoffs on the floor):
Always keep work area clean.
−Risk of injury by objects being caught during sawing by the revolving saw blade (e.g. tools on the saw table or metal parts hidden in the workpiece):
Keep saw table clean. If in doubt check workpiece for inclusion of foreign matter.
−Risk of kickback (workpiece is caught by the saw blade and thrown against the operator):
Always work with a properly set riving knife. Keep blade sharp and do not jam.
−Hazard generated by environmental influences:
Do not operate the circular saw in rain or in damp environment. Ensure sufficient lighting. Do not operate the circular saw near inflammable liquids or gases.
−Danger to other persons in the work area: Keep bystanders, particularly children, out of the danger zone.
−Hazard generated by overloading:
Use circular saw within its limits, and only as specified.
−Danger by machine faults:
Check the circular saw for damage before every use. Before switching ON check to see that keys or setting tools are removed. Do not operate the saw with a damaged ON/OFF switch. Keep knobs and handles free of oil and grease.
PK 255 |
2.3 |
ADanger!Disregard of the following warnings can lead to severe personal injury or material damage.
Read instructions.
Do not reach into the revolving saw blade.
f Wear hearing protection.
Use push stick if distance between saw blade and rip fence is ≤ 120 mm.
Cut round stock only with a suitable holding device.
Use table extension, if otherwise workpiece would fall off the table after cutting.
Max. saw blade Ø |
250 mm |
Saw blade arbor bore Ø 30 mm
Max. blade speed |
4000 min-1 |
Max. depth of cut |
80 mm |
2.4
Riving knife
The riving knife prevents the workpiece from being caught by the rising teeth of the saw blade and being thrown against the operator.
Always have riving knife installed during operation.
Blade guard
The blade guard protects against accidental contact with the blade and keeps chips from flying about.
Always have blade guard installed during operation.
Push stick
The push stick serves as an extension of the right hand and protects against accidental contact with the saw blade.
Always use push stick if distance between rip fence and saw blade is ≤ 120 mm.
In order for the push stick to be always at hand, it can be stored in a sheath in the machine's housing.
PK 255