Robot Vacuum Cleaner
D56 User Guide
Thanks for purchasing
patented
Robot
Vacuum Cleaner
Thanks again for your choice!
products Hope you can enjoy it
. !
Content
1. Safety In struction................... .... ..
... 9. Day-to-Day Storage.......................... 16
...3
User Guide............................ .... ... 10. Maintenance.................... .... .........
Power Supply for the Product......... .....
The Spectrum of Product Use....... ....... Dust Box Cleaning
Note s before Cleaning.................. .... . Cotton Filter Cleaing............ ............
Child Safety................... .... ......... ... Sponge Filter Replacement
Batt ery Replacement and Disposal Main Brush Cleaning.......... ..............
Resource Utilization Side Brush Cleaning
When Product is in Failure.......... ......
2. Content in the Original Package an d
Technical Parameter.... ..... ... ......
3. Name of Parts
The Host ................................ . ...
LCD and Control Panel..........................9
4. Battery Char ging.................... ..
Asse mbly Charging Block.......... .......
Robot Charging................ ..
.... .........................6 ...........................19
.... ............................ .... 8
.. ..... 3 .... 16
.. 3 Host Cleaning....................................16
.. 4 .... ..........................16
... 5 ... 17
. ..... 5 .................18
........6 ... 18
.... . 6 Side Brush Replacement.....................19
Driving Whe el Cleaning.......................1 9
.... .. ... 7
. ........ 8
.... ...... 9
.... . 9
.... ............ 10
Up-Ground Height Sensor Cleaning....19
Dust Sensor Cleaning.........................20
11. Al arming................... .... .......
12. Common Failure............... ......... .....
13. . .. 22
Othe r Problems.......... ....... ............
.... ... ...... 20
.. 21
5. Power On/Pause/Power Off....... .. ...
Power On..................... .... ..... .
Pause...... ............. ...... ...... .........
Power Off................. ....................
6. .... ..... 12
Mode Selection............... .... ......
Auto matic Cleaning Mode ....... ...
Bord er Cleaning Mode.... ....... .... ..
Fixe d Point Cleaning Mode........... ...
Inte nsive .... . . ... 13
Go Back Cha rging Mode......... .... ....
7. Automatic Charging...........................14
14
8. Appointment Time Setting.................
Set Appointment Time Cleaning...........14
Set Current Time Cleaning
Cleaning Mode....... .. . ..
.... ... .... . 11
...... .. 11
.... .. 11
.... ..... . 12
... .. . . 13
.... ...............15
... 11
.... 13
.. ... 13
Enjo y S m a r t e r L i f e !
1.Safety Instruction
NO
NO
Guardrail
Guardrail
Set up
Guardrail
Warni ng： Where ther e is a drop off in the cleaning area due t o a step or
stairs and they ar e n ot carpeted, you sho uld operate the unit to see that the
unit can detect the step without falling over the edge. It may beco me
necessary to place a p hy sical barrier at the e dge to keep the unit from falling
over the d ro p but make sure the physica l bar ri er is high enou gh so that you
or a family membe r wi ll not trip on the ba rr ier and cause the mselves injury.
Note：
Do not open the equipment. Th e co mp onents inside the robot host are beyond repair by
user himself.
This product is only for domestic use, not su it ab le for industry or outdoor surroundings.
Please do not press LCD.
The User Guide
Please conform to the basic safety precauti on s as follows:
● Read the content in this user guide carefully a nd i ns tall the robot according to the detailed instru ct io ns.
● Safekeeping this guide. If you transfer thi s ma chine to another person, please make sure attach th is b ooklet.
● Any inconsistent operation with this guid e wo ul d probably cause serious damage to both human bei ng a nd t he
machine itself.
Power Supply for the Product
CorrectCorrect
Electricity
leakage
Cloth
cleaning
● The power supply is from a Ni-MH chargeable bat te ry inside the host of the
robot and it is specially assigned with a charg in g bl ock to do recyclable
charge.
● Please double check the marked supply volta ge o n th e charging block and
make sure it is applied according to the instru ct ions.
● Do not use the damaged power cord or plug, while co nt ac t our after-sales
service or find our authorized supplier to ma in ta in.
● As the charging block is heavy, pl ea se never drag the block via pulling it’s
power cord.
● Remember never twist, swing or screw the powe r co rd e xcessively.
Neither block it when close the door. Also we sho ul d no t put heavy
things on the robot as well.
● Do not let power cord touch hot or sharp surfaces .
● Do not draw out the plug by pulling the cord.
● Keep wet hands away from the plug or machine.
Draw out
Draw out
the plug
the plug
● Pull the plug out of socket when you no longer use th e ch ar ging block for
some time.
● Use dry cloth to wipe the dust on the plug frequent ly.
3
The Spectrum of the Product Use
● The robot is applicable to domestic sweepin g, i nc luding wooden floor,
rubber floor, ceramic tile, linoleum and med iu m or s horthaired carpet.
However, it is inapplicable to longhaired ca rp et .
● It can not be used for the floor as below:
---- Hav e wa te r on the surface ( including flammabl e li qu ids) , such
as wet floor.
---- Ins id e to ilet, shower room or other humid situation.
---- Sta ir ca se.
---- The r oo m wi th furnace or flame.
● The following objects are definitely forb id de n:
---- Not e xt in guished soot, burning cigarette butts or matc h, b ec ause
these objects would cause fire.
---- Sha rp o bj ects like glass debris, pin, paper clip, stones, gypsum,
and large piece of paper. Thes e th in gs may block the machine.
---- Water or other kind of liq ui d, e specially detergent, kerosene,
petrol, paint, alcohol, perfume, as well as c ar pet or floor cleaning solution.
It would make the interior of the machine wet, so t ha t may cause shortcircuit.
---- The t on er o f laser printer and copier which may bring fire and
explosion.
● Please keep the machine away from hot source su ch a s oven and
fireplace, because the hot can distort th e cr us t.
● Do not use the machine in the surroundings with a ny e xp losion risk.
For example, at gas station, oil depot, che mi ca l plant and so on.
● Never use the machine outdoors. As rain or solid dust may get inside i t an d
cause damage.
● Do not repair or change any performance by your se lf .
● Do not throw or bend the machine.
● Do not dampen it, or else the short-circuit wou ld c ause fire or electric
shock accident.
● Take care of routine maintenance and keep it in a cle an p la ce.
● Do not expose the machine in the extreme hot or col d su rroundings. This
product is not allowed to long-time kept in the t em perature below zero or
over thirty degree.
● Do not keep the machine in the liquid or expose it to h ig h hu midity.
● Do not place the machine close to burning cigar et te o r fire.
4
Notes before Cleaning
Enjo y S m a r t e r L i f e !
● Take extra care of the robot when the first it work s. P le ase remove the
obstacles when it is beyond the robot.
● Make precautions to solve the problem which m ay m ak e the cleaning in
trouble, such as:
----
---- Per mi an t he edge of the carpet.
---- The h an gi ng tablecloth and curtain should not touch the gr ou nd .
---- The f la mmable object should be cut from the fire source.
---- Sor t ou t the tangled power cord on the floor.
● Check whether the main brush is correctly fix ed i ns ide the robot before
● Examine if the dust box is empty and insure it is fix ed .
● Please check whether up-ground height sen so r an d dust sensor have
● Please close the door if you just want to clean one r oo m.
Keep the easily knock over objects in a safe plac e.
cleaning.
been wiped clean.
Child Safety
● Children, physically or mentally disabl ed p eo ple are not allowed to use it,
unless their safety supervisors accompa ny t hem to give instruction.
5
Battery Replacement
and Disposal
● Take good care of the product and keep it beyond chil dr en a nd people who
cannot judge danger nearby. Extra attenti on s ho uld be paid when the
robot starts working.
● You should g et t he p eople inside the room know that the machine is work in g
to avoid man-made damage like damaging.
● Do not take robot as toy. Care fu ll y attention should be paid when child or
pet is around.
● The plastic package may bring danger of asphy xi a an d is supposed to keep
away from children.
● You should c on ta ct our after-sales when you want to change the batt er y. It
will cause explosion if you use the wrong batte ry.
● There is potential danger if you use other prod uc er 's battery and charging
block, which is not within our warranty.
Resource Utilization
When Product is in Failure
● Please dispose the old battery properly, because there is hazardous
substance, which may pollute the environm en t.
● Conform to the local environmental legisl at io n and dispose it at the recovery
site.
● Do not take the package material as domestic ga rb ag e and discard it
freely.
● Please deliver the package material to prop er r ec overy site for recycle.
● Do not repair or disassemble the machine when t he re i s damage of the
power cord.
● Contact our after-sales service or our desi gn ate maintenance organization
for professional repair.
6
2.Conte n t
Enjo y S m a r t e r L i f e !
Robo t Vacuum C leane r
D56 Us er Guid e
Host
Roll brush clean-up
Charging block
Side brush
gadget
technique parameter
The host The charging block
Working voltage In-put voltage
Rated power
Speed
Capacity of dust box
Noise
Charging duration
DC14.4V AC220-240V
30W
0.25m/s
0.7L
≤62dB
About 4~5 hours
rated out-put voltage
rated frequency
rated power
rated out-put
currency
User guide
DC17.5V
50Hz
30W
0.7A
Duration upon full
battery 60 minutes
Max Coverage upon
full battery
Size
Net weight
60 minutes
12 0-1502M
335×335×100mm
2.8Kg
7
3.Name of parts
host
control b utton
LCD
welted
inducti on
infrare d
receive r
chargin g dock
electro de
buffe r plate
wind gate
rotatin g side br ush
main brus h
rubber sc raper
on/off switc h
dust sens or
dust sens or
dust box
chargin g and ala rm
open butt on of upp er cove r
up-g round h eight sen sor
dust box ha ndle
ash exit
antibac teria l
sponge fi lter
lock of dus t box
All-rou nd
wheel
suspend ed
driving w heel
bottom view
of robot
elevation of robot
8
docking e lectr ode
power cor d
charging block
wind gate
dust box
power ind icato r
infrare d trans mitte r
anti-sk id band
LCD Display and Control Panel
17
18
19
20
21
Enjo y S m a r t e r L i f e !
22
1
16
mo de
2
3
15
14
13
11
10
9
7
8
5
6
4
12
1. P ower 7. B order c leani ng mode 13. One-time timin g clean ing 19. Tip f or clea ning dust b ox
2. M odel se lecti on 8. Inte nsive c leani ng mode 14. Time disp lay 20. Tip f or lack ing dust bo x
3. O n/Pau se 9. A utoma tic cle aning mode 15. Tim e clean ing status 21. Tip f or trap ped
4. P ause st atus 10. Opera tion st atus 16. Appoi ntment time sett ing 22. Tip f or driving wheel
5. F ixed po int cle aning mode 11. Cance l timin g cleanin g 17 . Tim e setting s tatus
6. G o back ch argin g block 12. Keep timi ng clea ning 18. Battery displa y
suspend ing
4.Robot Charging
Placement of charging block
Put the block at an even place and make the base perp en di cular to the ground.
Meanwhile, take a look at the marked electric it y voltage to make sure the
product is used under instruction.
9
Tangle the power co rd and do not sca tter it be sides the block in case tha t
robot would get impeded when it turns back.
0. 5m
0. 5m
Robot Charging
1.5m
chargi ng
sta tus
Ind ica tor
fla shi ng
There should not be any object at least 1.5 meter in front of the charging
block. Besides, anything with strong reflector is not supposed to stay ahead of
the infrared receiver. For example, ground glass, smooth ceramic vase and so
on. Otherwise, the machine shall not detect t he c harging block.
Tips:
Plea se do not put the charg ing block to the staircase to avoid
acci dental cases.
● You need to charge the robot the first time it wor ks . Put away the full
charged battery for use to ensure its perfo rm an ce.
● Charging duration should be around 4~6 hour s.
●
Charging is only allowed under the temperat ur e be tween 0 and 45 degree,
and extreme hot or co ld would extend ch arging duration or even cause
the damage of the battery.
Tips:
To mak e sure the robot is w or king in saturation, we su gg est you to
keep charging connected even though the charging indicator lasts
lighting. At the sam e time, the system would trans fe r to weak current
for supplementary charging.
10
chargi ng
sta tus
Ind ica tor
last
lighti ng
According to ac tu al ground situation, robot can keep working for
around 45 minutes after being charged full.
The capacity of battery, whic h is not used for long time, will get
certain decrease, so the use time can be shorte n ac cordingly.
5.Power On/ Pause/ Power Off
Get power sup ply and power on
● Turn on the p ow er switch on the bottom firstly.
● Get power supp ly and pres s the bu tt on on h os t. There would be a
short music tip and at the same time the batter y in di cator lights.
mode
Enjo y S m a r t e r L i f e !
Pause
Power off
mode
mode
Pres s button to start the robot●
● Press key, it c an pause the operation of robot a nd k ee p it stay
where it is.
Tips:
On the status of pause, yo u can reset t he cleaning m od e, then
press
Another way to pause the ro bot is that you can press any b ut to n
or lift the robot.
● Press key, power is off and the r ob ot s tops running.
button to restart the robot.
mode
Tips:
If you want the robot to stop r unning, you can press button
under pause status.
Put the robot back to the charging block after it s to ps working for
fear that others would be tripped.
11
Tips:
Put the robot on the charging block and keep it cha rg in g after
finishing house cleaning.
Do not keep the robot on pause status for long ti me , be cause the full
charged battery could only last for around 20 h ou rs . We suggest
you to turn it off when you do not wa nt i t to w ork.
10
6.Mode Selection
mode
mod e
Press btuuon, th en robo t
will foll ow the be llowi ng acti on.
auto edge spot return intensive
Automatic Cleaning Mode
Stat us instruction:
The details of three statuses mentioned as be ll ow ing:
Working status: robot is doing cleaning job
Standby status:
Case one: press button but without any oper at io n.
Case tw o: press button or any other button on host when robot i s
running.
Case three: lift the robot.
Power off status: robot is not power o n, or under working or s tandby
status, press button, robot is power off.
Route de sc ription:
obstacle.
If r obot d et ects t ha t th er e is plenty of dust during the clean process. It
will take the fan-shaped or spiral route.
.
First ro bot going straight ahead, it turns wh en it m eets
12
Under normal circumstance, it will take spiral r oute whe n it det ects
plenty of large particles, and will t ak e fan-shaped route when few of
small particles.
0. 5M
If take this mo de, the cleaning covera ge would reach m ax im um
compared b y the same ground c on di tion. We recommend this m od e
when the ground is not too dirty and needs quick cl ea ni ng.
The clean c an last 45 minutes under this mode, when it de te cts low
battery, the robot will go bac k ch arging.
Border Cleaning Mode
Enjo y S m a r t e r L i f e !
Route descript io n:
(like wall), it will run along it t o clean until it meets o bstacle and c ha ng e the
former route.
Fixed Point Cleaning Mode
Route description: under this mode, robot runs from inside in s pi ral way and
focused on th e certain point to clean fo r one time. The cleaning coverage is a
round shape with diameter of 1.2 meter.
under this mode, once the robot detects hard objects
Under this mode, robot he lp s to clean the corner of wall, table,
sofa and bed where it is beyond the mode of automat ic c le aning.
The op eration of this mode takes around 25 minutes and then robot
goes back charging by itself.
This mode is applicable to certain area with pl en ty o f dust.
Under common circumstance, the cycle of o ne fi xed point cleaning
takes ar ou nd 6 minutes. During op er ation, if robot continually meets
obstacle or detects st ai rc ase, it wo ul d shi ft to avoid obstacle and
staircase, and then turn back to work under thi s mo de.
Intensive Cleaning Mode
Route description:
go back charging before run off t he b attery.
Go Back Charging Mode
Route description:
detects low battery, green l ig ht flashing once the charger is connected.
Robot will stay where it stops and give tip music a ft er f inishing.
the route is the same as automatic mode. The robot will
Under the same ground circumstance, the cle an in g effect is the best.
Please choose this mode when the ground is quit e di rt y.
robot will search for charging block automa ti ca lly when it
13
7. Automatically charging
？
strait room
?
?
strait room
● When robot detects the low battery, it will go back charging automatically.
● To make it easy for robot to search for charging bloc k, y ou need to put the
block back to the wall and make sure there is no obst ac le within 1.5 meters
ahead of the infrared receiver. Check carefu ll y wh ether there is strong
reflector in front of the charger, such as gro un d gl ass, smooth ceramic vase
and so on.
● It takes time for robot to seek the charger. Rob ot c an r eserve enough
battery to go back to the charging block.
● If put the robot in a strait room, please make su re t ha t there is enough
space for robot to go back charging.
● Robot can return to the charger if the ground sit ua tion is not too
complicated, Under extreme circumstan ce , such as, huge house,
complex layout would bring diff iculty for robot to seek for charger. So,
you should help to put the robot back to the chargi ng b lo ck.
● Please take care of the first automatic cha rg in g, if you find the robot keeps
turning in the certain area after trying seve ra l ti mes to seek back, you can
help to place it on the charging block and look thr ou gh t he charging.
● When the robot goes back charging, the main bru sh w il l stop working.
And robot shall stay at the charger when it finis he s ch arging and it
transfer to small currency to charge until yo u st art operating.
8. Appointment Timing
Set appointment time
Tips:
Selection scope: hour is between 0 and 23, minu te i s
between 0-59.
Under normal circumstance, time display o n LC D sh ows
current time.
mode
mode
1. After power is on, keep press for
around 3 seconds, then on LCD is light
and the number with time setting is
flashing.
2. Set hour and minute via and , press
will increase one hour or minute. While
decrease one hour and minute for .
3. When you finish setting time, press
button again and then go to the current
time setting.
For example:
Set time as
12:07 am, time
display o n LCD
should be :
14
Set current time
mode
Enjo y S m a r t e r L i f e !
1. After appointment time setting, the la be l
high light, and the number with time setting
is flashing.
2. Set hour and minute via and , each time
press will increase one hour or minute,
while decrease one hour and minute for .
mode
3. Press again, and then go to frequency
setting.
Tips:
Selection scope: hour is between 0 and 23, minu te i s
between 0-59.
Under normal circumstance, time display o n LC D sh ows
For example:
Set current time
as 12:07 pm ,t ime
display o n LCD
should be :
current time.
Note :
When power is off, robot will n ot s tart work on appointment time. If you have already se t ap pointment
timing cleaning, please turn on the robot and k ee p it o n standby status.
Make sure the socket is connected to the power su pp ly. Otherwise, robot will fail t o wo rk o n appointment
time under standby status because of runnin g ou t of battery.
Set Frequency and Cancel Timing
Tips:
Robot will turn to the automatic mode when the ap po in ted time coming.
If the robot is working under border mode or fixe d- point mode, when the appointed time coming, robot
will not operate appointment cleaning unt il t he n ext time coming.
Press to adjust appointment cleaning fr eq ue ncy:
Press the button , the robot
to clean on appointment time for one time.
will work as belowing sequence:
to clean on appointment time everyday herea ft er.
to cancel appointment timing, robot only wo rk s upon your manual
operation.
work for
one time
work
everyd ay
do not
work
15
9.Day-to-day storage
10. Maintenance
Host Cleaning
You should k ee p ro bot stay at charger even though it finishes charg in g,
because it will change to small currency to sup pl em ent charging.
Charge the robot until full battery and put it ba ck t o th e package if you
do not need to use it for ling time. Keep the package i n dr y
surroundings to avoid sunshine or humidit y.
Turn off the power before cleaning the host.
Draw out the plug of charger before cleaning th e bl oc k.
mode
Dust Box Cleaning
1
1
open bu tto n
of dust b ox
Do not use petrol or oil-like to clean the surfac e, w hile you can use water
or neutral detergent to scrub. Make sure you us e dr y cloth to wipe,
because any water is not allowed to infiltrat e in to the machine.
Please follow the belowing steps:
turn off the power.
press "open" button.
Take off the upper cover.
16
Enjo y S m a r t e r L i f e !
2
4
6
1
1
1
Hold the handle of
dust box and lift it to
take out.
Match the bottom with
trash can and swing
dust box gently. You can
mildly beating it along
the edge of the can to
get the dust out.
Pour out the dust on
sponge filter.
3
5
7
1
1
1
In order to avoid dust
leaking, lift the suction up
when you take out dust
box. Please mind your
speed doing this step.
If there is too much dust
on sponge filter, you can
open the lock and take off
the cover.
Close the cover and hear
"kaca" sound, which
shows that it is
placed.Put the dust box
back into the host.
：
Tips
If the dust box is not placed back or not properly pl ac ed , The indicator lights.
Sponge Filter and Dust Box Cleaning
Open the lock at the
bottom of dust box.
Pour out the dust on
sponge filter.
If there is too much dust
along dust box, you can put
the box under running
water to get rid of the dust
(make it dry under
sunshine for 24 hours). Put
it back into the host after
the box and sponge filter is
completely dry.
17
1
1
Sponge Filter Replacement
1. Open the cover of the Deebot,
take out the dust box.
2. Push aside the lock catch of the
dust box ,then open the dust box
and clean it.
3. Extract the axle of the dust box’s
cover.
4. Replace the sponge filter and fix
the cover ,then put it back into
Deebot.
Main Brush Cleaning
Undo the screw fixed on the
main brush.
4
4
Remove the hair and dust
which is in-between the belt.
Tips: Clean the main brush af te r it h as operated for 4 or 5 recycles.
1
2
2
Take off the frame of main brush. Take out one side of main
brush from the belt.
1
2
4
5
Rip off the hair on main brush
(with equipped roll brush
cleaning gadget to break off th e
hair on main crush along the
groove.
Wipe the dust on the roller
and put it back.
3
6
7
Put the main brush back to the
host and take care of the
anastomosis of belt.
18
8
Fix the frame into host. Tie up the sc re w.
9
1
Side Brush Cleaning
Enjo y S m a r t e r L i f e !
Side brush is a kind of easy wear part. We suggest you to check it every time it
takes cleaning task. Please change it if nece ss ary.
Note：
The host will alarm when the side brush tangles a nd t he lights.
Replace Sidebrush
Please remove the screws,
and take out the side brush.
Please replace the side brush when it is destro ye d.
Driving Wheel Cleaning
Please use the roll brush cleaning gadget to re mo ve t he dust or hair on driving
wheel.
If the wheel is tangled by hair or cloth, the host wi ll a larm and it will show
on LCD as .
Up-ground Height Sensor Cleaning
Up-grou nd heig ht sens or
Up-ground height sensor is on the front botto m of r obot. It can detect the
height difference withi n 8 ce nt imeters. We suggest you to wipe t he o pt ical
board with dry cotton cloth after it finish es t as k to prevent the dust piling on it
which would affect its perf or ma nce.
Please push the new side brush
into the correct position.
Note:
Tight the s cr ews.
1. Turn off the power and remove t he t rash.
2. Invert the robot,and then put it on the even a nd c le an platform.
3. Use dry cotton cloth to wipe three optical b oa rd o f up-ground.
19
Dust Sensor Cleaning
The dust sensor is located at the front of dust
entrance. It is able to detect the concentr at io n of
dust so that it can choose effi ci ent mode to work.
We suggest you to clean dust se ns or o nce you
clean dust box to improve work effi ciency.
1. Turn off power.
2. Take out dust box and clean it.
3.Wipe the dust sensor with dry cotton cloth.
1 .Alarm function1
The robot will stop working and be alarm and tip so un d at t he
same time. Please do as bellowing to solve the pr ob le m.
Icon Cause of failure Solution Ins truction
1. Too much dust in
the dust box.
2. There is too much
dust on dust
sensor.
1. Dust box is not fixed
into host.
2. Dust box is not fixed
properly.
1. Main brush or
driving wheel is
tangled by hair or
cloth.
2. Side brush is
blocked.
1. Clean thedust
box.
2. Clean the dust on
dust sensor.
1. Put dust box back
into host.
2. Re-install dust box
and press it down at
the same time.
1. Clean main brush.
2. Clean side brush
and put it back.
Note :
In order to extend use life, Robot will
alarm even though there is not much
dust inside after several cycles cleaning .
20
Driving wheel is
suspended.
Low battery.
Put the robot back on
charger to charge.
Put the robot back
manually.
This function can prevent danger of child
or pet lifting the robot when it is operating.
12. Common Failure
No. Problem Solution
Turn off the power.
1.Check if there is dust on up-ground height
1
2
Robot keeps proceeding or moving
backward once power is on.
Robot is in trouble.
sensor, which cause robot to make wrong
signal. Use half dry cloth to clean it.
2.Buffer collision is out o f co ntrol. Put your hand
at left, middle and right in turn to see if it can
rebound by itself.
Robot may fall in trouble when it is working. In
such case, it will try every possibility to g et o ut
of trouble, but it shall stay at a certain plac e
when it fails and starts alarm. You should help
it and get rid of the obstacle.
The trouble may be as follows:
1.It is tangled by power cord.
2.It is tangled by hanging curtain or fringe.
Too many obstacles before the robot.
Enjo y S m a r t e r L i f e !
Robot is able to detect most of the stairs abov e
8 centimeters height diff er en ce. However, its
3
4
Robot fails to detect the stairs.
The capacity to clean weakens.
performance will weaken when it is smooth flo or
with height difference or t he f loor with strong
reflector.
Turn off power and take out the dust box, then
follow the steps as below:
1.Check whether there is too much dust on
sponge filter so that it needs to change it.
2.Make sure there is no dust, which blocks the
suction.
3.Take out main brush and clean it. Insure the
both ends of main brush is not tangled by hair
or fiber. Fix it back after it is been cleaned.
4.Examine if there is dust or debris near drivin g
wheels.
5.Clean dust sensor
If the failure still there after following th e st eps
above, please contact our after-sales.
21
Turn off the power supply, and th en t ake out of
dust box. After removing the garbage,
overturn the robot.
1. Check whether the suction of main brush is
5
There is much noise when the robot
works.
blocked.
2. Examine and clean the main brush.
3. Examine and clean the side brush.
If the failure is still there after operati ng
according to the above procedure, Please
contact our after-sales service.
13. Other Problems
1. How long can robot last working under Answer: Because when there is l ow b at tery,
full battery? it will do back to charging mode
Answer: It differs from th e gr ou nd situation,
It takes around 45 minutes for even floor 6 What's th e cl ea ning coverage once it is
such as wooden floor and ceramic tile, and charged full?(under automatic clean in g
20 minutes for short-haired carpet. mode)
automatically.
.
2. Is it allowed for the robot to work Answer: Under normal circumstance, it is
independently without taking care of? around 40 sq, but it differs fr om t he ground
Answer: Yes. However, you should keep
person in the room informed about robot 7 Why does r ob ot s top working once it
operating to avoid tipping. meets obstacle?
3. What kind of equipment inside the robot An swer: Under normal circumstance, robot
is used for dealing with failure? will return or seek other route when it meets
Answer: It is equipped with photosensiti ve
components, which can detect the stair over
the height of 8 centimeters; for fear that it
would fall over. 8. Why there is garbage leaking from the
.
4 Is robot ab le t o cl ean the bottom of the
furniture? Answer: a. Please check whether there is too
Answer: It is flat design, during normal
cleaning, it can go into table and bed corner
whose height is over 10 centimeters, such as
bed, wardrobe, sofa and tea table.
.
5 Why does ro bo t fa il to work under set
mode?
situation.
.
obstacle. However, if it controlled by remot e
control, it is not able to change route in case
of obstacle.
machine while robot operating?
much garbage in dust box(if there is too
much dust on the floor, robot is not able to
alarm after working for some time even
though there is too much garbage in dust
box.). That's why you need to c le an dust
box. b. See whether main brush is not
cleaned for long time, as it is tangled with
much hair and dust.
22
Enjo y S m a r t e r L i f e !
.
9 Why does ro bo t fa il to start cleaning on avoid wrong operation by child.
appointment time?
.
16 Is there any danger to wrongly to uc h the
Answer: a.Confirm whether there is much docking electrode film between the host
remaining battery. Appointment timing is no t and charger?
applicable when robot is returning to charg e
after operating cleaning. b. Check if robot i s
under standby status.
.
10 Why robot is not charging as it is pu t in 24V which is safe one under input
Answer: No. The two electr od es o f charger is
of no voltage under output mode(when there
is no power supply); it's maximum voltage is
the charger? The charging indicator doe s m od e( when it is charging)
not light as well.
17.
How does main brush avoid being tangled
Answer: a. Examine whether the battery at by po wer cord?
the bottom is installed in place, if cover
screw is loose, you need to fasten it. b.
Check if there is power supply for the socket.
c. Please contact our after-sales servi ce
when the failure is still there.
.
11 Why does the speed of robot slow do wn
sometimes?
Answer: When robot detects there is much
garbage and dust on the floor, it would turn
to low speed proceeding automatically.
.
12 Is there any danger to furnitur e an d child
when robot is proceeding?
Answer: No. There is a soft ru bb er b uffer
made of PPC in front of the host. It would try
other route once it touches furniture or ch il d.
.
13 Would robot a ff ec t pet?
Answer: Robot makes low noise when
Answer: Robot is probably get tangled by the
wire scattered on the floor when it is
operating. At that time, robot will try to tur n
back to get rid of it, and it will make alarm
sound when it fails after trying several time s.
18. How can I stop the robot f ro m op erating
on appointment time since I will be away
from home for sometime?
Answer: You can cancel cycle cleaning.
Refer to page 14.
19. How can I transfer my robo t?
Answer: You can lift it up with both your
hands and lay on the ground quickly; dust
and garbage in dust box will come out if it is
not place back in time.
dee
b
ot
operating, so there would be no shrill sound
which may cause pet restless or even
distrust. If you keep pet at home, we suggest
you to notice the first time the robot
operating.
.
14 What should be noticed when cle an ing
the carpet?
Answer: Robot is not able to clean long hair
over 2 centimeters. Fold the banding first
when you start cleaning.
20. How to use robot most effe ct ively?
Answer: Put the robot and charger in the
same room, because it would shorten
seeking time and it can extend the working
time. If you need robot to clean every room
of house, you should put the charger in the
.
15 Does it matter to keep the robot at t he
charger when not using it?
middle of house for the convenience of
return back to charge.
Answer: Yes. Robot will transfer to small
currency to supplement charging. Please
23
.
21 What should do if robot sucked li qu id?
Answer: a. Turn off the power a nd t ak e out
dust box, then empty it and wipe it dry. b.
Draw out the sponge filter and wipe it dry. c.
Take out main brush and clean it, then use
day cloth to wipe the brush and its interior.
Wait unti l th e brush is day and place it back.
d. Let the product dry by itself for at least
12hours(make sure circuit board is dry and
then get power on)
If the procedures above still do not make
it work, please contact our after-sales
service.
24
Enjoy smarter life!
D56-000I M2 01 011
Loading...