Page 1
Focus XD
Owner’s
manual
Page 2
Owner’s Manual Focus XD
dynaudio.com/focusxd We thank you / Table of contents
Thank you
Thank you for choosing Dynaudio Focus XD loudspeakers.
Every Focus XD model features advanced Dynaudio
loudspeaker technology that turns listening to music into an
impressive experience. This technology results from many
years of intense research and development, the highest
quality standards in production, and Dynaudio’s enduring
passion for musical truth.
Each Focus XD loudspeaker is constructed by Dynaudio’s master craftsmen in Denmark
to these high standards of quality. To realize the highest sound quality from the Focus XD
models, some areas should be addressed, as will be explored on the following pages.
By considering the tips and suggestions, you will achieve the maximum performance and
enjoyment of the Focus XD and its advanced musical capabilities for a long time to come.
We hope you have a great time listening to your favourite music.
Dynaudio
Table of contents
4 Safety information
5 About this guide
5 Expressions and symbols used
6 Scope of delivery
6 Unpacking
6 Packaging material
6 Disposal
7 Setting up
8 Floor-standing loudspeaker setup
8 Compact loudspeaker setup
9 Selecting the installation location
9 Right and left loudspeaker
10 Distance to walls
10 Distance to the listening position
11 Loudspeaker toe-in
11 Grille
12 Connection and operation
13 Connections and control elements
14 Remote control
14 Control elements
15 Connecting the loudspeakers
15 Connecting the digital signal source
16 Connecting the analog signal source
17 Operating the loudspeakers
without controlling the volume
18 Adjusting the loudspeakers’ sound
18 Adjusting the low-frequency range
18 Adjusting the treble
19 Connecting the voltage supply
19 Switching on/standby mode
20 Selecting inputs on the loudspeakers
20 Selecting the hub inputs
20 Selecting a hub (HUB)
20 Selecting an input on the hub (INPUT)
20 Adjusting the volume
20 Muting the loudspeakers
21 Display
21 Malfunctions
24 Firmware update
25 Technical data
26 Care & maintenance
27 Warranty
P3P2
Page 3
Owner’s Manual Focus XD
dynaudio.com/focusxd Safety instructions / About this guide
Safety
instructions
Dangerous electrical voltage
If the loudspeakers are connected to the mains voltage, a
dangerous electrical voltage is present inside the speakers.
Never open the loudspeaker housing.
Do not operate defective loudspeakers and disconnect defective loudspeakers from
the mains voltage. Please contact your Dynaudio distributor if you have any problems.
Distributor addresses can be found in the Internet at www.dynaudio.com.
Use the supplied power cable to connect the loudspeakers to the mains voltage. Make
sure that the power supply cable is not damaged; exchange it for a new one if it has
been damaged.
High sound pressure levels
Listening to high sound pressure levels over a longer period
of time may harm your hearing.
To avoid auditory effect, do not listen to high sound levels over a longer period of time.
About this
guide
Used expressions and symbols
In this operating manual following signs and symbols are used:
ATTENTION: Indicates a hazard that could result in damage or destruction of the product.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
Indicates (in combination with a safety sign) a potentially hazardous situation which, if not
avoided, could result in minor or moderate injury or damage to equipment.
Indicates a hazard that could result in death or severe injury.
The arrow will identify steps to be performed. Please follow the instructions carefully.
Always make sure to follow the instructions given in these passages.
Multiple steps that should be performed consecutively are numbered.
1.
Please follow these instructions carefully.
2.
Note
Additional information is provided, which is important to fully understand the
loudspeaker and how to operate it.
P5P4
Page 4
Owner’s Manual Focus XD
1. 2 Focus XD loudspeakers (60 XD, 30 XD, or 20 XD)
Scope of
delivery
2 Focus XD loudspeaker cloth covers (not shown)
2. 1 remote control
3. 2 power cables (country-specic version)
1 rst time setup manual (quick guide for installation, not shown).
321
dynaudio.com/focusxd Unpacking / Setting up
Unpacking
Disposal
After unpacking, make sure the system is complete and check the device and all
accessories for transport damage. Transport damage may be expected if the packaging is
already severely harmed. Do not attempt to commission a damaged device. If the contents
are incomplete or damaged, please contact your Dynaudio distributor.
Distributor addresses can be found in the Internet at www.dynaudio.com.
Packaging material
The packaging has been designed so that it may be reused if it was not damaged during
transport. Keep the packaging and use the original packaging for all further transport.
Disposal of used electrical and electronic equipment (applicable in European countries with
separate collection systems for this equipment).
This symbol on the product or its packaging indicates that the product may not be treated
as household waste. Instead it must be handed over to the applicable collection point for
the recycling of electrical and electronic equipment. By ensuring this product is disposed
of correctly, you will help prevent potential negative consequences for the environment and
human health. The recycling of materials helps to conserve natural resources.
For more detailed information on recycling this product, please contact your local authority,
community waste disposal ofce, or the shop where you purchased the product.
Spikes with sharp peaks
The oor-standing Focus XD loudspeakers allow for setup with spikes. The sharp peaks of
the spikes may cause injuries and damage sensitive surfaces like hardwood ooring or tile.
Be careful when handling the loudspeakers.
►
Place plates between the spikes and the surface to protect the underlying surface.
►
ATTENTION
Light, heat, electromagnetic radiation
Direct sunlight or excessive brightness can affect the colour of your loudspeakers’ natural
wood veneer. Built-up heat can lead to overheating. Electromagnetic radiation of different
devices can lead to mutual impairment to functions.
Avoid placing the device in very warm, cold, or humid environments.
►
To maintain the aesthetic quality of your loudspeakers for the long term, placement in
►
light-intensive, sunny environments should be avoided.
Please ensure sufcient ventilation and observe the required distances around the
►
loudspeakers.
Do not place the loudspeakers near devices with strong electromagnetic radiation or
►
devices that could be destroyed or damaged by magnetic elds.
P7P6
Page 5
Owner’s Manual Focus XD
Spike on oor-standing Focus XD.
dynaudio.com/focusxd Setup / Location
Display
Left Right
Floor-standing loudspeaker
setup
Compact loudspeaker setup
The oor-standing Focus XD loudspeaker features a special base construction, which offers
both an ideal performance and mechanical basis. The spikes screwed into the end of the
feet on the base can be unscrewed and their height adjusted, to adapt to uneven oors.
When the spikes are retracted, the loudspeakers stand on rubber feet. These stabilize
the cabinet on an extremely small contact area, and therefore prevent any wobbling while
offering optimal resonance control.
The best setup variant depends on the nature of the room and the oor in particular.
Your Dynaudio distributor would be happy to assist you during setup.
The compact Focus models are designed to offer exceptional performance while taking up
minimal space. Due to adverse effects to the sound quality, compact loudspeakers should
not be placed on the oor. The mini-monitors will realize their optimum performance when
used in conjunction with a stand to position them at the proper height while absorbing any
resonance. Please contact your Dynaudio distributor for more details.
Due to its dimensions, you can also place the loudspeaker on a ledge or shelf or on top of
furniture. To avoid the possibility of any negative inuence on sound quality, make sure to
utilize a stable surface offering a wide enough space in front of the loudspeakers as to not
limit the sound quality and performance.
Selecting the installation
location
Right and left loudspeaker
The Focus XD loudspeakers do not require special positioning, though the quality of the
individual loudspeakers’ sound is affected by the acoustic properties of the room. Since
rooms are shaped uniquely, the positioning of the loudspeakers results in totally different
behaviour. For example, large rooms without much furniture and many clean, hard wall
surfaces can give a bright and diffuse sound with diverse echoing frequencies. A room with
thick carpet, curtains and soft furniture surfaces will give a slightly warmer, darker and less
lively sound.
The following information steps are therefore general directions that will make correct
positioning easier to achieve. Furthermore, we recommend taking advantage of the
services provided by your Dynaudio distributor to fully exploit the sound potential of your
loudspeakers in your own listening room.
The outside of the left and right loudspeakers is different, with a different arrangement of the
display (see gure above) and labelling on the rear side.
Position the loudspeakers in the desired location.
►
P9P8
Page 6
Owner’s Manual Focus XD
A
B
A
BB
dynaudio.com/focusxd Setup / Location
Distance to walls
Distance to the listening
position
D ≥ 0.5 m
Every loudspeaker not only disperses sound energy directly into the room, but also to
the side and even backwards. As a result, time-delayed reections occur and add to the
original music signal. Thus, when loudspeakers are positioned too close to walls, the sound
quality can be restricted. Focus XD loudspeakers were developed to be placed free-
standing, and therefore they reach their optimum performance when positioned as clear of
any walls as possible.
To reduce possible inuences from the back and sidewalls, the distance to these
►
boundaries should ideally not be less than 0.5 meter.
Adjust the sound of your loudspeakers (see page 18).
►
The distance between each loudspeaker and your listening position should be the same
•
(B). Try to achieve an isosceles triangle.
The distance between the loudspeakers should be the same or, preferably, slightly less
•
than the distance between each loudspeaker and your listening position (A, B).
The closer the listening position is in relation to the loudspeakers, the closer the
•
speakers can be positioned to each other.
As a starting point, it is recommended that the speakers be about 2 meters apart from
•
each other for the best results (A).
If the speakers are positioned too close to each other, the stereo image will not seem
•
realistic; if that distance is too wide, the image may leave an acoustic hole in the middle.
Paying attention to the image during listening tests will help dictate optimum placement
•
during experimentation and setup.
A≤B
Loudspeaker toe-in
Grille
Depending on your personal listening environment and room dimensions, the loudspeakers
may be angled in towards the listening area to focus the sound radiation. This positioning
will typically improve imaging and is especially recommended by Dynaudio. However, you
are free to select the precise position based on your personal listening habits.
A cloth grille is included and can be afxed to the cabinet to help protect the drivers from
dust and any other inuences. The grille is acoustically optimized, but the highest sound
quality levels will be attained without any grille covers in place during listening.
If a front grille is used, it is held on the front of the housing by means of magnets.
Removing and attaching the front grille:
To remove the grille, gently pull the grille at all corners straight away from the front.
►
To t the grille, line it up exactly in front of the housing with the logo facing upwards and
►
carefully push the cover onto the loudspeaker.
P11P10
Page 7
Owner’s Manual Focus XD
dynaudio.com/focusxd Connection and control elements
Connections
and control
elements
This section describes the connections and control elements
for the components. Please contact your Dynaudio distributor
if you have any problems with connection and start-up.
Distributor addresses can be found on the Internet at
dynaudio.com. The active loudspeakers have an integrated
amplier and can be controlled with the remote control.
CONNECTIONS AND CONTROL ELEMENTS
Digital Audio
Analog Audio
Service
Speaker Position
Treble
Zone
Channel Mode
Power
Digital connection. IN = input, OUT = output
Analog connection. IN = input, Input sensitivity = manual correction of the input sensitivity (+6 / 0 / -6 dB)
USB port for rmware update
Sound adjustment (depending on the position of the loudspeakers). Sound adjustment is performed with a
rotary knob with 7 positions. With the 3 main positions, the rotary knob clicks into place:
Neutral = with free-standing placement. Wall = if placed near a wall. Corner = if placed in a corner
Treble adjustment (+1 / 0 / -1 dB)
Selecting the audio zone (Xeo hub operation)
Loudspeakers assigned to different zones can be controlled separately via the remote control.
The zones are identied as Red, Green, and Blue.
Master = loudspeaker operated as master. Slave = loudspeaker operated as slave.
External = loudspeaker congured as active loudspeaker (at full performance)
Power switch. I = The loudspeaker is on. The loudspeaker can be activated and deactivated via the remote
control. If the loudspeaker is activated and there is no signal, it will switch to standby mode.
O = The loudspeaker is completely off.
Mains socket. To connect the loudspeaker to the mains voltage.
P13P12
Page 8
Remote control
The remote control can be used to turn the loudspeakers on and off, change the volume,
switch between digital and analog input, switch the display on or off, and select a hub and
its connected signal sources.
dynaudio.com/focusxd Remote control / Connecting the loudspeakersOwner’s Manual Focus XD
CONTROL ELEMENTS
MUTE
ON/OFF
VOLUME
DIRECT
INPUT
1/2/3/4
HUB
A/B/C
Muting the loudspeakers
Briey pressing this button will mute or unmute the selected
loudspeaker.
Loudspeaker on/off
= on. = switch to standby
Changing the volume
= louder. = quieter
Direct selection
= toggle between digital and analog input
= switch the display on/off
Selecting the signal source
Selects one of the signal sources Line In, Optical In, Coax In
or USB In from the active hub.
Selecting the Hub or Connect
Selects one of three possible Hubs or Connects A, B, or C.
Connecting
the
loudspeakers
Connecting the digital signal source.
To connect the loudspeakers, switch all components off.
►
Connecting the digital signal source
You can connect your loudspeakers as follows:
Both loudspeakers are connected using cables. This requires two digital cables but the
•
systems benets from signal processing of 24 bits/192 kHz.
You only connect one loudspeaker using a cable; the connection between the
•
loudspeakers is wireless. This requires one digital cable and provides signal processing
capabilities of 24 bits/96 kHz.
Both loudspeakers are operated wirelessly via a Dynaudio Hub or Connect box with
•
signal processing of 24 bits/96kHz.
Connecting both loudspeakers with cables
1. Connect the digital output for the signal source to the digital input (Digital Audio IN) on
one loudspeaker. You can choose whether to use the right or left loudspeaker.
2. Operate the connected loudspeaker as master by setting the Channel Mode switch on
the rear side of the housing to Master.
3. Connect the digital output on the master loudspeaker to the digital input (Digital Audio
IN) on the other loudspeaker.
4. Operate the loudspeaker connected in this step as slave by setting the Channel Mode
switch on the rear side of the housing to Slave.
P15P14
Page 9
Owner’s Manual Focus XD
Connecting the digital signal source
Operating via Hub or Connect.Operating with a cable. Connecting the analog signal source.
dynaudio.com/focusxd Connecting the analog signal source / Operating the loudspeaker without controlling the volume
Connecting only one
loudspeaker with a cable
1. Connect the digital output for the signal
source to the digital input (Digital
Audio IN) on one loudspeaker. You can
choose whether to use the right or left
loudspeaker.
2. Operate the connected loudspeaker as
master by setting the Channel Mode
switch on the rear side of the housing
to Master.
3. Operate the other loudspeaker as slave
by setting the Channel Mode switch
on the rear side of the housing to
Slave.
Operating the loudspeakers
via a Hub or Connect
Dynaudio’s innovative Connect system
offers the option to operate the loud-
speakers completely wirelessly. The
connection to the loudspeakers is
established by either a Dynaudio Hub or
Connect box to which the analog and/
or digital sources can be connected. For
more details, please refer to the Connect
Owner’s Manual or learn more at http://
www.dynaudio.com/home-audio/connect/
1. Install and congure the Connect
system according to the Connect
owner’s manual.
2. On the rear side of the housing,
select the red, green, or blue
zone. Loudspeakers that belong to
a common zone can be operated
together using the remote control.
3. Operate one loudspeaker as master
and the other as slave by setting the
respective switch (Channel Mode)
correspondingly on the rear side of the
housing. The assignment of master and
slave is irrelevant.
Connecting the analog signal
source
The loudspeakers can also output signals
from an analog signal source. The signal
source is connected to the analog inputs.
1. Connect the left analog output from
the signal source to the analog
input (Analog Audio IN) on the left
loudspeaker.
2. Connect the right analog output
from the signal source to the analog
input (Analog Audio IN) on the right
loudspeaker.
3. Operate one loudspeaker as master
and the other as slave by setting the
respective switch (Channel Mode)
correspondingly on the rear side of the
housing. The assignment of master and
slave is irrelevant.
Operating the loudspeakers
without controlling the volume
You can also operate the loudspeakers
without controlling the volume yourself.
The ampliers integrated into the
loudspeakers function as a power
amplier; volume is controlled via the
source signal (e.g. pre-amplier).
1. Connect the left analog output from
the signal source to the analog
input (Analog Audio IN) on the left
loudspeaker.
2. Connect the right analog output
from the signal source to the analog
input (Analog Audio IN) on the right
loudspeaker.
3. Set the Channel Mode switch on the
back side of the housing to External.
High sound pressure levels
In the External operating mode, signals
are amplied at the maximum. Connecting
a signal source with an uncontrolled or
maximum level can harm your hearing and
cause damage to the components.
Only connect controllable signal
►
sources.
Before switching on the loudspeakers,
►
turn down the volume for the signal
source using its volume control.
P17P16
Page 10
dynaudio.com/focusxdOwner's Manual Focus XD Adjusting the loudspeaker’s sound / Connecting the voltage supply
Adjusting the
loudspeakers’
sound
The sound of Focus XD loudspeakers can
be adjusted by increasing or lowering high
and low frequencies. Each loudspeaker
can be set separately and individually
based on the room conditions and
personal listening preferences.
Adjusting the low-frequency range
The Speaker Position rotary knob allows
you to lower low frequencies. This allows
you to balance out elevated or cancelled-
out low-frequency signal portions, as they
often occur in living spaces.
Set the Speaker Position rotary knob
►
to the desired position on the back side
of the housing for each loudspeaker.
There are 2 additional intermediate
stages between each of the main
positions that click into place (Neutral,
Wall, and Corner).
–– Neutral: free-standing loudspeaker (no
change to sound).
–– Wall: if placed near a wall.
–– Corner: if placed in a corner.
Adjusting the treble
Using the Treble switch on the rear side
of the housing allows you to adjust the
character of the sound to your listening
preferences.
Set the Treble switch on the rear side
►
of the housing to one of three settings:
+1 dB: Increase, creates a somewhat
•
brighter sound.
0 dB: Neutral position, no change.
•
–1 dB: Lowering, creates a somewhat
•
warmer sound.
Connecting the
voltage supply
Use the supplied power cable to
►
connect the loudspeakers to the mains
voltage and switch it on using the
power switch (POWER) on the rear
(position: I).
Switching on/standby mode
To switch the loudspeaker on from
standby mode:
Point the remote control at the
►
loudspeaker and press the ON button.
The loudspeaker will automatically
search for an audio signal or an
active hub. If found, the signal will be
output. If there is no input signal, the
loudspeaker will go into standby mode
after a certain period.
To switch it back on, press ON or start
►
music playback.
To switch a loudspeaker out of
operation to standby mode:
Point the remote control at the
►
loudspeaker and press the OFF
button. The loudspeaker will go into
standby mode. To completely switch
off the loudspeaker, turn the POWER
switch on the rear to O. However, the
loudspeaker can then no longer be
switched on via the remote control.
Note
Before connecting the device,
check whether the mains voltage
listed on the rear side of the
speakers matches that present at
the installation site.
P19P18
Page 11
Owner’s Manual Focus XD
dynaudio.com/focusxd Display / Display meaningsSelecting inputs on the loudspeakers / Adjusting the volume
Selecting inputs on the
loudspeakers
Press the DIRECT button on the
►
remote control. The loudspeakers
toggle between the analog and digital
input if the corresponding signal
sources are connected.
Selecting the Hub or Connect inputs
Optionally, the loudspeakers can also be
operated with a Dynaudio Hub or Connect
box. For details on operation via Hub or
Connect, please refer to the Connect
Owner’s Manual.
Selecting a Hub or Connect (HUB)
Press HUB A, B, or C on the remote
►
control. The chosen Hub or Connect is
selected as the signal source.
Selecting an input on the Hub or
Connect (INPUT)
Press INPUT 1, 2, 3, or 4 on the
►
remote control. The selected signal
source will be played back.
Night Mode
Briey pressing the MOON button
►
on the remote control will activate
Night Mode. When in Night Mode, the
status LEDs will only be lit up when
the speaker is receiving commands
from the remote control. After a few
seconds, the LEDs will turn off. Press
the MOON button again to disengage
Night Mode.
Fixed Volume
Press and hold the MUTE button to
►
set the volume to a xed, high level.
To disengage the Fixed Volume mode,
simply change the volume level using
the Volume +/- buttons on the remote.
Disabling/Enabling Autosense
In normal operation, the Focus XD will
►
go to stand-by if it does not sense an
incoming signal. Hold the ”Direct In”
button on the remote for 5 seconds,
to disable or enable Autosense. The
status LED will blink once for enabling,
and twice for disabling Autosense.
Note that when Autosense is off, the
speaker will remain On, until the user
actively sets the speaker in Stand-By
using the Off button.
Adjusting the volume
Change the volume by pressing the
VOLUME button on the remote control.
Press to turn the volume up.
►
Press to turn the volume down.
►
Muting the loudspeakers
Briey pressing the MUTE button on
►
the remote control will mute or unmute
the selected loudspeaker.
Note
If loudspeakers are operated in hub
mode in different zones, the volume
is controlled separately. For details
on operation via the Xeo hub,
please see the Xeo owner’s manual.
Display
The display on the top edge of the housing
indicates the operational state of the
loudspeakers and system using LEDs with
various colours and ash functions.
The display can be switched on or off with
the button on the remote control.
LED DISPLAY MEANINGS
On-state
The bottom LED is illuminated in blue.
The bottom LED is lashing in blue.
The bottom LED is illuminated in violet.
Off-state
The bottom LED is illuminated dimly in red. The loudspeaker is in standby mode.
The loudspeaker is switched on and an audio signal
is played back.
The loudspeaker is switched on, but an audio signal
cannot be found on the selected input.
The loudspeaker is switched on and an audio signal
is played back. The master and slave loudspeakers
are connected with a cable.
P21P20
Page 12
Owner’s Manual Focus XD
dynaudio.com/focusxd Display meanings
LED DISPLAY MEANINGS
Hub or Connect connection
The bottom LED is ashing red. There is no active Hub or Connect, or no
connection to a Hub or Connect possible
Switch-on process
LEDs are illuminated one by one. The loudspeaker is being switched on.
Switch-off process
The LEDs go out one by one.
The loudspeaker is being switched off.
In the nal state, only one LED is
illuminated dimly in red.
Displaying the direct input
One of the two LEDs ashes.
LED 1 = digital INPUT
LED 2 = analog INPUT
LED DISPLAY MEANINGS
Displaying the selected Hub or Connect
One of the three LEDs ashes. LED 1 = HUB A
LED 2 = HUB B
LED 3 = HUB C
Displaying the input source
One of the four LEDs ashes. LED 1 = INPUT 1
2nd LED = INPUT 2
3rd LED = INPUT 3
4th LED = INPUT 4
Searching for an input
The blue LED ashes; the lights in the
Searching for an active input
white LEDs move back and forth.
Searching for an active input on the hub
The blue LED ashes, the white LEDs
briey light in order. A hub input has been selected and the hub is
searching for an active input.
P23P22
Page 13
Owner’s Manual Focus XD
dynaudio.com/focusxd Display meanings Technical data
Firmware update
LED DISPLAY MEANINGS
Volume, mute
A number of white LEDs are illuminated.
The rst LED ashes.
Firmware update
The white LEDs light in order. A rmware update is being performed.
1. Copy the rmware le onto an empty
USB stick.
2. Switch the loudspeaker off using the
power switch on the rear of the device.
3. Insert the USB stick in the USB port on
the rear side of the housing.
4. Switch the loudspeaker on (power
The number of LEDs indicates the selected volume.
The loudspeaker is muted.
The procedure is completed in just
a few seconds. The loudspeaker
enters standby mode automatically.
5. Switch the loudspeaker back off and
remove the USB stick.
6. Repeat steps 2–5 with the second
loudspeaker.
switch on the rear of the device).
The rmware update is performed
automatically.
The while LEDs will light in
ascending order (see above).
Note
The rmware update must be
performed separately for each
loudspeaker.
LOUDSPEAKERS FOCUS 20 XD FOCUS 30 XD FOCUS 60 XD
Frequency range (± 3 dB) 39 Hz – 24 kHz 29 Hz – 24 kHz 18 Hz – 24 kHz
Power consumption during operation
Power consumption in standby
Amplier performance
Dimensions (H x W x D)
Weight
Voltage supply
Inputs
18 – 200 W 18 – 200 W 18 – 200 W
< 1 W (with active network) < 1 W (with active network) < 1 W (with active network)
Subwoofer: 150 W
Tweeter: 150 W
360 x 198 x 307 mm 980 x 198 x 307 mm 1095 x 213 x 337 mm
8.65 kg 18.5 kg 27 kg
100 – 120 V/220 – 240 V,
50/60 Hz
Digital audio IN (16/24 bit: 44.1/48/88.2/96/176.4/192 kHz), cinch, SPDIF (75 ohm coax)
Digital audio OUT (16/24 bit: 44.1/48/88.2/96/176.4/192 kHz), cinch, SPDIF (75 ohm coax)
Analog audio IN (input sensitivity: +6 dB/0 dB/–6 dB), cinch, 1/2/4 Vrms
Service, USB, rmware upload
Wireless (bit/kHz: 16/48 and 24/96), 2.4/5.2/5.8 GHz
Subwoofer: 150 W
Midrange: 150 W
Tweeter: 150 W
100 – 120 V/220 – 240 V,
50/60 Hz
Subwoofer 1: 150 W
Subwoofer 2: 150 W
Midrange: 150 W
Tweeter: 150 W
100 – 120 V/220 – 240 V,
50/60 Hz
P25P24
Page 14
Owner’s Manual Focus XD
dynaudio.com/focusxd
dynaudio.com/focusxd Care & maintenance / warranty
Care &
maintenance
P26
Dynaudio loudspeakers require no special
treatment apart from the kind of careful
handling you would normally apply to any
high-tech product in your home.
Aggressive cleaning uids
All-in-one cleaning agents, aggressive
cleaning uids or special furniture polishes
may damage the cabinet surface or other
speaker parts.
Use a soft dry or slightly damp cloth
►
when cleaning the cabinet and other
plain parts.
Cleaning the loudspeakers
Switch off all components of your
►
system when cleaning any of these
components or in case of extended
absences.
Avoid touching the tweeter domes as
►
any change of their shape may have an
impact on sound quality.
Clean the cabinet and other plain parts
►
with a soft dry or slightly damp cloth
only.
Remove dust on the woofer
►
diaphragms with a ne furniture brush.
All materials used by Dynaudio are
integrated with exceptional care. By
taking care of your loudspeakers, you will
preserve the nish and build quality for a
very long time.
Warranty
The warranty is based on the statutory regulations of
the respective country. Furthermore, Dynaudio offers an
extended warranty after registration online at http://www.
dynaudio.com/register. Please refer to the information
during registration for warranty periods.
This warranty only covers faults or defects in material and production. Damage caused as a
result of abuse, misuse or defective electronics is not covered by the warranty. All warranty
claims must be accompanied by a copy of the original purchase invoice and warranties are
only valid in the country or market of original origin or distribution. Should warranty service
be required, it must be arranged for in the country of purchase by an authorized Dynaudio
dealer.
Malfunctions
You can ask your Dynaudio distributor for assistance at any time or contact the Dynaudio
helpline at info@dynaudio.com.
Further information can also be found on the Focus XD website at focusxd.dynaudio.com.
P27
Page 15
Focus XD
Designed,
engineered and
assembled in
Denmark
Dynaudio A/S
8660 Skanderborg
Denmark
www.dynaudio.com
Focus XD - Owner’s manual,
version 06/17.
All text and image copyrights reserved.
Subject to change without notice.
Loading...