COMFORT CONTROL CENTER 2 THERMOSTAT
OPERATING INSTRUCTIONS
PROGRAMMABLE THERMOSTAT
MODEL
3314080.000 BLACK
3314080.015 WHITE
USA |
CANADA |
For Service Center & |
SERVICE OFFICE |
Dometic Corporation |
Dealer Locations |
Dometic Corporation |
46 Zatonski, Unit 3 |
Please Visit: |
1120 North Main Street |
Brantford, ON N3T 5L8 |
www.eDometic.com |
Elkhart, IN 46514 |
CANADA |
REVISION B |
|
|
|
|
|
Form No. 3314149.018 08/16 |
|
|
(French 3314169.016_B) |
|
|
©2016 Dometic Corporation |
|
|
LaGrange, IN 46761 |
INTRODUCTION
Congratulations! Your recreational vehicle manufacturer has equipped your RV with the most advanced RV thermostat. Your Dometic Comfort Control Center 2 thermostat
(hereinafter referred to as the CCC 2 thermostat) has been designed for ease of operation and for many years of reliable service.
DometicCorporationreservestherighttomodifyappearancesandspecifications without notice.
TABLE OF CONTENTS |
|
|
INTRODUCTION............................................................................................................................................ |
2 |
|
DOCUMENT SYMBOLS................................................................................................................................ |
3 |
|
ABOUT YOUR NEW THERMOSTAT............................................................................................................. |
3 |
|
A. |
Features..................................................................................................................................... |
3 |
B. |
System Configuration & Initialization.......................................................................................... |
3 |
C. |
Quick Reference To Control Buttons.......................................................................................... |
5 |
D. |
Quick Reference To LCD Icons.................................................................................................. |
5 |
PROGRAMMING & OPERATIONS............................................................................................................... |
6 |
|
A. |
ON/OFF...................................................................................................................................... |
6 |
B. |
Clock Setting.............................................................................................................................. |
6 |
C. |
Temperature Format °F / °C....................................................................................................... |
7 |
D. |
Inside Temperature.................................................................................................................... |
7 |
E. |
Zone Selection........................................................................................................................... |
8 |
F. |
Mode Selection.......................................................................................................................... |
8 |
G. |
Fan Speed.................................................................................................................................. |
9 |
H. |
Temperature Set-Point............................................................................................................... |
9 |
MODE DESCRIPTION................................................................................................................................. |
10 |
|
A. |
“OFF” - Off Mode...................................................................................................................... |
10 |
B. |
“COOL” - Cool Mode................................................................................................................ |
10 |
C. |
“HP” - Heat Pump Mode........................................................................................................... |
10 |
D. |
“HS” - Heat Strip Mode............................................................................................................. |
11 |
E. |
“FAN” - Fan Mode.................................................................................................................... |
11 |
F. |
“FURN” / “AQUA” - Furnace Or Aqua (Hydronic) Heating Mode.............................................. |
11 |
G. |
“AUTO” - Auto Change Over Mode.......................................................................................... |
12 |
SPECIAL FEATURES.................................................................................................................................. |
12 |
|
A. |
Auto Fan................................................................................................................................... |
12 |
B. |
Zone Control............................................................................................................................ |
13 |
C. |
Program “1” & “2”..................................................................................................................... |
13 |
D. |
Examples Of Times Programmed............................................................................................ |
15 |
E. |
CANbus Interface..................................................................................................................... |
15 |
F. |
Auxiliary Heat (Heat Pump Models Only)................................................................................. |
16 |
G. |
Stage Select - Two Air Conditioner/Heat Pump Units (Select Models) On One Zone............. |
16 |
H. |
Stage Select - Dual Compressor Air Conditioner/Heat Pump (Select Models)........................ |
16 |
I. |
Auto Generator Start (AGS)..................................................................................................... |
17 |
J. |
Load Shed ............................................................................................................................... |
17 |
K. |
Defrost Cycle (Heat Pump Models Only)................................................................................. |
17 |
L. |
Compressor Time Delay........................................................................................................... |
17 |
M. |
Power Interruption.................................................................................................................... |
18 |
N. |
LCD Error Code....................................................................................................................... |
18 |
SYSTEM RESET PROCEDURE................................................................................................................. |
19 |
|
GENERAL INFORMATION.......................................................................................................................... |
19 |
|
2
TABLE OF CONTENTS |
|
|
A. |
Reduce Heat Gain.................................................................................................................... |
19 |
B. |
Disclaimer................................................................................................................................ |
19 |
MAINTENANCE........................................................................................................................................... |
20 |
|
A. |
Air Filter.................................................................................................................................... |
20 |
B. Dometic CCC 2 Thermostat..................................................................................................... |
20 |
|
SERVICE |
..................................................................................................................................................... |
20 |
DOCUMENT SYMBOLS
Indicates additional information that is not related to personal injury.
Indicates step-by-step instructions.
ABOUT YOUR NEW THERMOSTAT
A.Features
●● Liquid Crystal Display ●● Two operation programs
●● Constant time of day display
●● Remote Sensor (Precise comfort control within 1 °F of set-point)
●● Display reminder lets you know when to service or replace filters
●● Up to four independent zones
To help familiarize yourself with the operation of the CCC 2 thermostat, review the following diagrams and accompanying text that explain the functional characteristics of this system.
Your CCC 2 thermostat is equipped with a liquid crystal display (LCD) that identifies the mode of operation (OFF, Cool, Heat Pump, Fan, Heat Strip, Auto, & Furnace or Aqua), temperature set-point, zone identification (“1”, “2”, “3”, “4”), fan speed (“Auto,” “Low,” “Med,” “High”), program “1” and “2”, inside temperature, clock, °F / °C, compressor delay, and filter maintenance. The modes of operation viewed in the LCD will vary depending on the system installed in your RV.
B.System Configuration & Initialization
The installer of your system will set the required system DIP switches to the ON position. In order for the CCC 2 thermostat to recognize the system zones, type of units installed and their options, a system reset must be done.
3
ABOUT YOUR NEW THERMOSTAT
Once the system is completely installed, do a system reset:
1. Make sure the CCC 2 thermostat is in the OFF mode. See section, “C. Quick
Reference To Control Buttons” on page (5).
2.Simultaneously press and hold the MODE and ZONE buttons. See section, “C.
Quick Reference To Control Buttons” on page (5).
3.The LCD will display “IniT” and all available zones.
4.Release the MODE and ZONE buttons.
5.Press the ON/OFF button to exit system set up.
6.The furnace ON/OFF temperature differential should be set at this time. For further information on furnace mode differential setting, see section, “F. “FURN”
/ “AQUA” - Furnace Or Aqua (Hydronic) Heating Mode” on page (11).
Any time a system reset occurs, the factory default settings are restored. See table,
“Factory Preset Settings” on page (4).
In the unlikely event of CCC 2 system memory loss or dip switch setting change, the
CCC 2 thermostat will require a system reset. For system reset procedure, see main heading, “System Reset Procedure” on page (19).
Your Dometic CCC 2 thermostat has been pre-programmed. Review settings below and adjust the settings to your personal comfort level.
Any time the CCC 2 is in an idle stage (not illuminated) you will need to wake it up by pressing any button on the CCC 2 before it will recognize a new setting attempt.
Factory Preset Settings
All Zones
Function |
Setting |
Time of Day (Clock) |
— — — |
Each Zone |
|
|
|
Heating |
68 °F / 20 °C |
Cooling |
72 °F / 22 °C |
Automatic |
70 °F / 21 °C |
Fan Speed |
Auto |
Mode |
Off |
Factory Preset Settings Each Zone
Program “1”
Function |
Setting |
Heating |
68 °F / 20 °C |
Cooling |
72 °F / 22 °C |
Automatic |
70 °F / 21 °C |
Fan Speed |
Auto |
Mode |
Off |
Time |
8:00 AM |
Program “2” |
|
Heating |
68 °F / 20 °C |
Cooling |
72 °F / 22 °C |
Automatic |
70 °F / 21 °C |
Fan Speed |
Auto |
Mode |
Off |
Time |
10:00 PM |
4
ABOUT YOUR NEW THERMOSTAT
C. Quick Reference To Control Buttons
Press to select zone |
Press to increase |
temperature set-point |
Press to select |
Press to display |
On and OFF |
inside temperature |
Press to select |
Press to select |
fan speed |
temperature format |
Press to set |
|
clock |
|
Press to |
Press to select |
Press to decrease |
select mode |
program 1 or 2 |
temperature set-point |
D. Quick Reference To LCD Icons
Operation Mode
Zone
Time of Day
Temperature
Set-Point or Error
Code
|
Program |
Fan Speed |
Clean or Replace |
|
|
Compressor |
Filter |
Delay |
|
5
PROGRAMMING & OPERATIONS
A.ON/OFF
To turn ON the CCC 2 thermostat when the back light is OFF, first press any button to wake up the CCC 2 thermostat. Then press and release the ON/OFF button. The
LCD will display the last programmed settings. To turn OFF the CCC 2 thermostat press the ON/OFF button and release. Only the time of day will display when the
CCC 2 thermostat is in the OFF condition.
B.Clock Setting
Press the CLOCK button to initiate the clock setting sub-menu on the CCC 2 thermostat. When in this menu, the hour digits will flash first. The hour can be adjusted using the or buttons. Press the CLOCK button again and the minute digits will flash, allowing the minute setting to be adjusted using the or buttons. Press it a third time and the AM or PM icon will flash, allowing the AM or PM setting to be adjusted using the or buttons. Press it one more time to store the new time in memory and exit the clock setting sub-menu.
6 |
Loading...