Size:
4.24 Mb
Download

USER GUIDE

Wireless-NBroadband Router

with Storage Link

Model: WRT160NL

About This Guide

About This Guide

Icon Descriptions

While reading through the User Guide you may see various icons that call attention to specific items. Below is a description of these icons:

NOTE: This check mark indicates that there is a note of interest and is something that you should pay special attention to while using the product.

WARNING: This exclamation point indicates that there is a caution or warning and it is something that could damage your property or product.

WEB: This globe icon indicates a noteworthy website address ore-mailaddress.

Online Resources

Website addresses in this document are listed without http:// in front of the address because most current web browsers do not require it. If you use an older web browser, you may have to addhttp:// in front of the web address.

Resource Website

Linksys www.linksysbycisco.com

Linksys www.linksysbycisco.com/international

International

Glossary www.linksysbycisco.com/glossary

Network Security www.linksysbycisco.com/security

Copyright and Trademarks

Linksys, Cisco and the Cisco Logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2009 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.

Wireless-NBroadband Router with Storage Link

i

Table of Contents

Chapter 1: Product Overview

 

 

 

1

Front Panel

 

 

 

1

Back Panel . . . . . . . . . . . . . . . . . . . .

. . . . . . . .

. . . .

.

. 1

Bottom Panel . . . . . . . . . . . . . . . . . .

. . . . . . . .

. . . .

. .

2

Chapter 2: Wireless Security Checklist

 

 

 

3

General Network Security Guidelines

 

 

 

3

Additional Security Tips . . . . . . . . . . . . . .

. . . . . . . .

. . . .

.

. 3

Chapter 3: Advanced Configuration

 

 

 

4

Setup > Basic Setup . . . . . . . . . . . . . . . .

. . . . . . . .

. . . .

.

. 4

Setup > DDNS

 

 

 

8

Setup > MAC Address Clone

 

 

 

9

Setup > Advanced Routing . . . . . . . . . . . .

. . . . . . . .

. . . .

. .

9

Wireless > Basic Wireless Settings . . . . . . . . . .

. . . . . . . .

. . . .

.

10

Wireless > Wireless Security . . . . . . . . . . . .

. . . . . . . .

. . . .

. .

12

Wireless > Wireless MAC Filter

 

 

 

14

Wireless > Advanced Wireless Settings . . . . . . . .

. . . . . . . .

. . . .

.

15

Security > Firewall . . . . . . . . . . . . . . . .

. . . . . . . .

. . . .

. .

16

Security > VPN Passthrough

 

 

 

17

Storage > Disk . . . . . . . . . . . . . . . . . .

. . . . . . . .

. . . .

.

17

Storage > Administration . . . . . . . . . . . . .

. . . . . . . .

. . . .

.

.20

Access Restrictions > Internet Access . . . . . . . .

. . . . . . . .

. . . .

. .

21

Applications and Gaming > Single Port Forwarding

 

 

 

22

Applications and Gaming > Port Range Forwarding . .

. . . . . . . .

. . . .

.

23

Applications & Gaming > Port Range Triggering . . . . . . . . . . . . . . . . . . . . . . . . . .23

Applications and Gaming > DMZ . . . . . . . . . .

. . . . . . . .

. . . .

.

24

Applications and Gaming > QoS . . . . . . . . . .

. . . . . . . .

. . . .

. .

24

Administration > Management

 

 

 

26

Administration > Log . . . . . . . . . . . . . . .

. . . . . . . .

. . . .

.

.27

Administration > Diagnostics . . . . . . . . . . . .

. . . . . . . .

. . . .

.

28

Administration > Factory Defaults

 

 

 

28

Administration > Firmware Upgrade . . . . . . . .

. . . . . . . .

. . . .

. .

29

Status > Router . . . . . . . . . . . . . . . . . .

. . . . . . . .

. . . .

.

29

Status > Local Network . . . . . . . . . . . . . .

. . . . . . . .

. . . .

. .

30

Status > Wireless Network . . . . . . . . . . . . .

. . . . . . . .

. . . .

.

.30

Appendix A: Troubleshooting

 

 

 

31

Appendix B: How to Install and Access USB Storage

 

 

 

33

Overview

 

 

 

33

Install the USB Storage Device . . . . . . . . . . .

. . . . . . . .

. . . .

.

.33

Access the USB Storage Device

 

 

 

33

Create a Shortcut to a Shared Folder . . . . . . . .

. . . . . . . .

. . . .

. .

34

Advanced Configuration (Advanced Users Only)

 

 

 

36

Wireless-NBroadband Router with Storage Link

ii

Table of Contents

Appendix C: Specifications

 

 

39

Appendix D: Warranty Information

 

 

40

Limited Warranty

 

 

40

Appendix E: Regulatory Information

 

 

42

FCC Statement . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . .

.

42

FCC Radiation Exposure Statement . . . . . . . . . . . . .

. . . . . . . .

.

.42

Safety Notices

 

 

42

Industry Canada Statement . . . . . . . . . . . . . . . .

. . . . . . . .

. .

42

Avis d’Industrie Canada

 

 

43

Wireless Disclaimer . . . . . . . . . . . . . . . . . . . .

. . . . . . . .

.

43

Avis de non-responsabilitéconcernant les appareils sans fil . .

. . . . . . . .

. .

43

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste

Electric and Electronic Equipment (WEEE)

 

 

44

Appendix F: Software End User License Agreement

 

 

48

Cisco Products . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . .

.

48

Software Licenses . . . . . . . . . . . . . . . . . . . .

. . . . . . . .

. .

48

Wireless-NBroadband Router with Storage Link

iii

Chapter 1

Product Overview

Chapter 1:

Product Overview

Thank you for choosing the Linksys by Cisco Wireless-NBroadband Router with Storage Link. The Router lets you access the Internet via a wireless connection or through one of its four switched ports. You can also use the Router to share resources such as computers, printers and files. The Router’s USB port connects to a USB storage device, so you can access your portable files. (A USB hard drive may require an external power supply.) A variety of security features help to protect your data and your privacy while you are online. Security features include WPA2 security, a Stateful Packet Inspection (SPI) firewall, and NAT technology. Configuring the Router is easy using the providedbrowser–basedutility.

Front Panel

1, 2, 3, 4  (Blue)  These numbered LEDs, corresponding with the numbered ports on the Router’s back panel, serve two purposes. If the LED is continuously lit, the Router is successfully connected to a device through that port. A flashing LED indicates network activity over that port.

Wi-FiProtected Setup ButtonIf you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup to automatically configure wireless security for your wireless network.

To use Wi-FiProtected Setup, run the Setup Wizard, or refer toWi-Fi Protected Setup,page 11.

Wi-FiProtected Setup LED(Blue/ Amber)  The LED lights up blue when wireless security is enabled. It flashes blue for two minutes during Wi-Fi Protected Setup.

The LED lights up amber if there is an error during the Wi Fi Protected Setup process. Make sure the client device supports Wi Fi Protected Setup.WaituntiltheLEDisoff,andthentryagain.

The LED flashes when a Wi Fi Protected Setup session is active. The Router supports one session at a time. Wait until the LED is solidly lit, or off before starting the next Wi-FiProtected Setup session.

Wireless  (Blue)  The Wireless LED lights up when the wireless feature is enabled. If the LED is flashing, the Router is sending or receiving data over the network.

Internet  (Blue)  The Internet LED lights up when there is a connection made through the Internet port. It flashes to indicate network activity over the Internet port.

Power  (Blue)  The Power LED lights up and will stay on while the Router is powered on. When the Router goes through itsself-diagnosticmode during everyboot-up,this LED will flash. When the diagnostic is complete, the LED will be solidly lit.

Back Panel

Antenna Ports  The femaleR-SMAantenna ports connect to the maleR-SMAconnectors of the included antennas.

Internet  The Internet port is where you will connect your cable or DSL Internet connection.

4, 3, 2, 1  These Ethernet ports (4, 3, 2, 1) connect the Router to computers on your wired network and other Ethernet network devices.

USB Port  The USB port connects to a USB storage device. If the storage device does not fit (for example, it may block port 1), then use the included USB extension cable.

Power  The Power port connects to the included power adapter.

Wireless-NBroadband Router with Storage Link

1

Chapter 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Product Overview

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bottom Panel

 

 

Wall-MountingPlacement

 

 

 

 

 

 

 

 

 

 

 

 

 

The Router has two wall-mountslots on its bottom

 

 

 

 

 

 

panel. The distance

 

between the slots is 152 mm

 

 

 

 

 

 

(6 inches).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Two screws are needed to mount the Router.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Suggested Mounting Hardware

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-3.0mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4-5mm

 

1-1.5mm

 

 

 

 

 

 

 

 

 

2.5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reset  The Reset button is located on the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

††Note: Mounting hardware illustrations are not

 

 

right side of the product label. There are two

 

 

 

 

 

 

true to scale.

 

 

 

 

 

 

 

 

 

 

 

ways to reset the Router to its factory defaults.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Either press and hold the Reset button for

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: Linksys is not responsible for damages

 

 

approximately five seconds, or restore the

 

 

 

 

 

 

 

 

 

defaults from the Administration > Factory

 

 

 

 

 

 

 

incurred by insecure wall-mountinghardware.

 

 

Defaults screen of the Router’s web based

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

utility.

 

 

Follow these instructions:

 

 

 

Horizontal Placement

 

 

1. Determine where you want to mount the Router. Make

 

 

sure that the wall you use is smooth, flat, dry, and

The Router has four rubber feet on its bottom panel. Place

 

 

sturdy. Also make sure the location is within reach of

 

 

an electrical outlet.

 

 

 

the Router on a level surface near an electrical outlet.

 

 

 

 

 

 

 

2. Drill two holes into the wall. Make sure the holes are

 

 

 

 

 

 

 

 

 

 

 

 

152 mm (6 inches) apart.

 

 

 

 

 

 

 

 

 

3. Insert a screw into each hole and leave 3 mm

 

 

 

 

 

 

(0.12 inches) of its head exposed.

 

 

 

 

 

 

4. Maneuver the Router so the wall-mountslots line up

 

 

 

 

 

 

with the two screws.

 

 

 

 

 

 

 

 

 

5. Place the wall-mountslots over the screws and slide

 

 

 

 

 

 

the Router down until the screws fit snugly into the

 

 

 

 

 

 

wall-mountslots.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

152 mm

Print this page at 100% size.

Cut along the dotted line, and place on the wall to drill precise spacing.

Wall-MountingTemplate

Wireless-NBroadband Router with Storage Link

2

Chapter 2

Wireless Security Checklist

Chapter 2:

Wireless Security Checklist

Wireless networks are convenient and easy to install, so homes with high-speedInternet access are adopting them at a rapid pace. Because wireless networking operates by sending information over radio waves, it can be more vulnerable to intruders than a traditional wired network. Like signals from your cellular or cordless phones, signals from your wireless network can also be intercepted. Since you cannot physically prevent someone from connecting to your wireless network, you need to take some additional steps to keep your network secure.

1.Change the default wireless network name or SSID

Wireless devices have a default wireless network name or Service Set Identifier (SSID) set by the factory. This is the name of your wireless network, and can be up to 32 characters in length. Linksys wireless products use linksys as the default wireless network name. You should change the wireless network name to something unique to distinguish your wireless network from other wireless networks that may exist around you, but do not use personal information (such as your Social Security number) because this information may be available for anyone to see when browsing for wireless networks.

2. Change the default password

For wireless products such as access points and routers, you will be asked for a password when you want to change their settings. These devices have a default password set by the factory. The Linksys default password is admin. Hackers know these defaults and may try to use them to access your wireless device and change your network settings. To thwart any unauthorized changes, customize the device’s password so it will be hard to guess.

3. Enable MAC address filtering

Linksys routers give you the ability to enable Media Access Control (MAC) address filtering. The MAC address is a unique series of numbers and letters assigned to every networking device. With MAC address filtering enabled, wireless network access is provided solely for wireless devices with specific MAC addresses. For example, you can specify the MAC address of each computer in your home so that only those computers can access your wireless network.

4. Enable encryption

Encryption protects data transmitted over a wireless network. Wi-FiProtected Access (WPA/WPA2) and Wired Equivalent Privacy (WEP) offer different levels of security for wireless communication.

A network encrypted with WPA/WPA2 is more secure than a network encrypted with WEP, because WPA/WPA2 uses dynamic key encryption. To protect the information as it passes over the airwaves, you should enable the highest level of encryption supported by your network equipment.

WEP is an older encryption standard and may be the only option available on some older devices that do not support WPA.

General Network Security Guidelines

Wireless network security is useless if the underlying network is not secure.

•• Password protect all computers on the network and individually password protect sensitive files.

•• Change passwords on a regular basis.

•• Installanti-virussoftware and personal firewall software.

•• Disable file sharing(peer-to-peer).Some applications may open file sharing without your consent and/or knowledge.

Additional Security Tips

•• Keep wireless routers, access points, or gateways away from exterior walls and windows.

•• Turn wireless routers, access points, or gateways off when they are not being used (at night, during vacations).

•• Usestrongpassphrasesthatareatleasteightcharacters in length. Combine letters and numbers to avoid using standard words that can be found in the dictionary.

WEB: For more information on wireless security, visitwww.linksysbycisco.com/security

Wireless-NBroadband Router with Storage Link

3

Chapter 3

Advanced Configuration

Chapter 3:

Advanced Configuration

After setting up the Router with the Setup Wizard (located on the CD-ROM),the Router will be ready for use. However, if you want to change its advanced settings, use the Router’sweb-basedutility. This chapter describes each web page of the utility and each page’s key functions. You can access the utility via a web browser on a computer connected to the Router.

The web-basedutility has these main tabs: Setup, Wireless, Security, Storage, Access Restrictions, Applications & Gaming, Administration, and Status. Additional tabs will be available after you click one of the main tabs.

NOTE: When first installing the Router, you should use the Setup Wizard on the SetupCD-ROM.If you want to configure advanced settings, use this chapter to learn about theweb-basedutility.

Access the Web-BasedUtility

To access the web-basedutility, launch the web browser on your computer, and enter the Router’s default IP address,192.168.1.1, in theAddress field. Then pressEnter.

A login screen will appear. (Non-WindowsXP users will see a similar screen.) Leave theUser name field blank. The first time you open theWeb-basedutility, use the default passwordadmin. (You can set a new password from theAdministration > Management screen.) ClickOK to continue.

Login Screen

Setup > Basic Setup

The first screen that appears is the Basic Setup screen. This allows you to change the Router’s general settings.

Setup > Basic Setup

Language

Select your language  To use a different language, select one from thedrop-downmenu. The language of the web based utility will change five seconds after you select another language.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Internet Setup

The Internet Setup section configures the Router to your Internet connection. Most of this information can be obtained through your Internet Service Provider (ISP).

Internet Connection Type

Select the type of Internet connection your ISP provides from the drop-downmenu. These are the available types:

•• Automatic Configuration - DHCP

•• Static IP

•• PPPoE

•• PPTP

•• L2TP

•• Telstra Cable

Wireless-NBroadband Router with Storage Link

4

Chapter 3

Advanced Configuration

Automatic Configuration - DHCP

By default, the Router’s Internet Connection Type is set to Automatic Configuration - DHCP, which should be kept only if your ISP supports DHCP or you are connecting through a dynamic IP address. (This option usually applies to cable connections.)

Internet Connection Type > Automatic Configuration - DHCP

Static IP

If you are required to use a permanent IP address to connect to the Internet, select Static IP.

Internet Connection Type > Static IP

Internet IP Address  This is the Router’s IP address, when seen from the Internet. Your ISP will provide you with the IP Address you need to specify here.

Subnet Mask  This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask.

Default Gateway  Your ISP will provide you with the IP address of the ISP server.

DNS 1-3  Your ISP will provide you with at least one DNS (Domain Name System) server IP address.

PPPoE

Some DSL-basedISPs use PPPoE(Point-to-PointProtocol over Ethernet) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to enablePPPoE.

Internet Connection Type > PPPoE

Username and Password  Enter the Username and Password provided by your ISP.

Service Name  If provided by your ISP, enter the Service Name.

Connect on Demand: Max Idle Time  You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default Max Idle Time is 15 minutes.

Keep Alive: Redial Period  If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default Redial Period is 30 seconds.

PPTP

Point-to-PointTunneling Protocol (PPTP) is a service that applies to connections in Europe only.

Internet Connection Type > PPTP

If your ISP supports DHCP or you are connecting through a dynamic IP address, then select Obtain an IP Address Automatically. If you are required to use a permanent IP address to connect to the Internet, then selectSpecify an IP Address. Then configure the following:

•• Specify an IP Address  This is the Router’s IP address, as seen from the Internet. Your ISP will provide you with the IP Address you need to specify here.

•• Subnet Mask  This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask.

•• Default Gateway  Your ISP will provide you with the IP address of the ISP server.

•• DNS 1-3  Your ISP will provide you with at least one DNS (Domain Name System) server IP address.

Wireless-NBroadband Router with Storage Link

5

Chapter 3

Advanced Configuration

PPTP Server IP Address  Your ISP will provide you with the IP address of the PPTP server.

Username and Password  Enter the Username and Password provided by your ISP.

Connect on Demand: Max Idle Time  You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default Max Idle Time is 15 minutes.

Keep Alive: Redial Period  If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automaticallyre-establishyour connection. To use this option, selectKeep Alive. In theRedial Period field, you specify how often you want the Router to check the Internet connection. The default value is30 seconds.

L2TP

L2TP is a service that applies to connections in Israel only.

Internet Connection Type > L2TP

Server IP Address  This is the IP address of the L2TP Server. Your ISP will provide you with the IP Address you need to specify here.

Username and Password  Enter the Username and Password provided by your ISP.

Connect on Demand: Max Idle Time  You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default Max Idle Time is 15 minutes.

Keep Alive: Redial Period  If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use

this option, select Keep Alive. In theRedial Period field, you specify how often you want the Router to check the Internet connection. The default Redial Period is30 seconds.

Telstra Cable

Telstra Cable is a service that applies to connections in Australia only.

Internet Connection Type > Telstra Cable

Server IP Address  This is the IP address of the Heartbeat Server. Your ISP will provide you with the IP Address you need to specify here.

Username and Password  Enter the Username and Password provided by your ISP.

Connect on Demand: Max Idle Time  You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default Max Idle Time is 15 minutes.

Keep Alive: Redial Period  If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default Redial Period is 30 seconds.

Optional Settings

Some of these settings may be required by your ISP. Verify with your ISP before making any changes.

Optional Settings

Host Name and Domain Name  These fields allow you to supply a host and domain name for the Router. Some ISPs, usually cable ISPs, require these names as identification. You may have to check with your ISP to see if your

Wireless-NBroadband Router with Storage Link

6

Chapter 3

Advanced Configuration

broadband Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will work.

MTU  MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet transmission. Select Manual if you want to manually enter the largest packet size that is transmitted. To have the Router select the best MTU for your Internet connection, keep the default,Auto.

Size  When Manual is selected in theMTU field, this option is enabled. Leave this value in the 1200 to 1500 range. The default size depends on the Internet Connection Type:

•• DHCP, Static IP, or Telstra:1500

•• PPPoE:1492

•• PPTP or L2TP:1460

Network Setup

The Network Setup section changes the settings of the local network. Wireless setup is performed through the Wireless tab.

Router IP

This presents both the Router’s IP Address and Subnet Mask as seen by your network.

Router IP

DHCP Server Setting

The settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer on your network. If you choose to enable the Router’s DHCP server option, make sure there is no other DHCP server on your network.

DHCP Server Setting

DHCP Server  DHCP is enabled by factory default. If you already have a DHCP server on your network, or you do not want a DHCP server, then selectDisabled (no other DHCP features will be available).

DHCP Reservation  Click this button if you want to assign a fixed local IP address to a MAC address.

DHCP Reservation

You will see a list of DHCP clients with the following information: Client Name, Interface, IP Address, and MAC Address.

DHCP Reservation

•• Select Clients from DHCP TableClick the Select check box to reserve a client’s IP address. Then click

Add Clients.

•• Manually Adding Client  To manually assign an IP address, enter the client’s name in theEnter Client Name field. Enter the IP address you want it to have in theAssign IP Address field. Enter its MAC address in the

To This MAC Address field. Then click Add.

Clients Already Reserved

A list of DHCP clients and their fixed local IP addresses will be displayed at the bottom of the screen. If you want to remove a client from this list, click Remove.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes. To update theon-screeninformation, clickRefresh. To exit this screen, clickClose.

Start IP Address  Enter a value for the DHCP server to start with when issuing IP addresses. Because the Router’s default IP address is 192.168.1.1, the Start IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.253. The default is192.168.1.100.

Maximum Number of Users  Enter the maximum number of PCs that you want the DHCP server to assign IP addresses to. This number cannot be greater than 253. The default is 50.

IP Address Range  Displayed here is the range of available IP addresses.

Client Lease Time  The Client Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP address. Enter the

Wireless-NBroadband Router with Storage Link

7

Chapter 3

Advanced Configuration

amount of time, in minutes, that the user will be “leased” this dynamic IP address. After the time has expired, the user will be automatically assigned a new dynamic IP address. The default is 0 minutes, which means one day.

Static DNS 1-3  The Domain Name System (DNS) is how the Internet translates domain or website names into Internet addresses or URLs. Your ISP will provide you with at least one DNS Server IP Address. If you wish to use another, enter that IP Address in one of these fields. You can enter up to three DNS Server IP Addresses here. The Router will use these for quicker access to functioning DNS servers.

WINS  The Windows Internet Naming Service (WINS) manages each PC’s interaction with the Internet. If you use a WINS server, enter that server’s IP Address here. Otherwise, leave this blank.

Time Settings

Time Zone  Select the time zone in which your network functions from thisdrop-downmenu. (You can even automatically adjust for daylight saving time.)

Time Settings

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Setup > DDNS

The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other server behind the Router.

Before you can use this feature, you need to sign up for DDNS service with a DDNS service provider, www.dyndns.org orwww.TZO.com. If you do not want to use this feature, keep the default,Disabled.

DDNS

DDNS Service

If your DDNS service is provided by DynDNS.org, then select DynDNS.org from thedrop-downmenu. If your DDNS service is provided by TZO, then selectTZO.com. The features available on theDDNS screen will vary, depending on which DDNS service provider you use.

DynDNS.org

Setup > DDNS > DynDNS

Username  Enter the Username for your DDNS account.Password  Enter the Password for your DDNS account.

Host Name  The is the DDNS URL assigned by the DDNS service.

System  Select the DynDNS service you use:Dynamic,Static, orCustom. The default selection isDynamic.

Mail Exchange (Optional)  Enter the address of your mail exchange server, so e-mails to your DynDNS address go to your mail server.

Backup MX  This feature allows the mail exchange server to be a backup. To disable this feature, keep the default,Disabled. To enable the feature, selectEnabled. If you are not sure which setting to select, keep the default,

Disabled.

Wildcard  This setting enables or disables wildcards for your host. For example, if your DDNS address ismyplace.dyndns.org and you enable wildcards, thenx.myplace.dyndns.org will work as well (x is the wildcard). To disable wildcards, keep the default,Disabled. To enable wildcards, selectEnabled. If you are not sure which setting to select, keep the default,Disabled.

Internet IP Address  The Router’s Internet IP address is displayed here. Because it is dynamic, it will change.

Status  The status of the DDNS service connection is displayed here.

Update  To manually trigger an update, click this button.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Wireless-NBroadband Router with Storage Link

8

Chapter 3

Advanced Configuration

TZO.com

Setup > DDNS > TZO

E-mailAddress, TZO Key, and Domain NameEnter the settings of the account you set up with TZO.

Internet IP Address  The Router’s Internet IP address is displayed here. Because it is dynamic, it will change.

Status  The status of the DDNS service connection is displayed here.

Update  To manually trigger an update, click this button.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Setup > MAC Address Clone

A MAC address is a 12-digitcode assigned to a unique piece of hardware for identification. Some ISPs will require you to register a MAC address in order to access the Internet. If you do not wish tore-registerthe MAC address with your ISP, you may assign the MAC address you have currently registered with your ISP to the Router with the MAC Address Clone feature.

Setup > MAC Address Clone

MAC Address Clone

Enabled/Disabled  To have the MAC Address cloned, selectEnabled.

MAC Address  Enter the MAC Address registered with your ISP here.

Clone My PC’s MAC  Click this button to clone the MAC address of the computer you are using.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Setup > Advanced Routing

This screen is used to set up the Router’s advanced functions. Operating Mode allows you to select the type(s) of advanced functions you use. Dynamic Routing automatically adjusts how packets travel on your network. Static Routing sets up a fixed route to another network destination.

Setup > Advanced Routing

Advanced Routing

NAT

Enabled/Disabled  If this Router is hosting your network’s connection to the Internet, keep the default,Enabled. If another router exists on your network, selectDisabled. When the NAT setting is disabled, dynamic routing will be enabled.

Dynamic Routing (RIP)

Enabled/Disabled  This feature enables the Router to automatically adjust to physical changes in the network’s layoutandexchangeroutingtableswiththeotherrouter(s). The Router determines the network packets’ route based on the fewest number of hops between the source and the destination. When the NAT setting is enabled, the Dynamic Routing feature is automatically disabled. When the NAT setting is disabled, this feature is available. SelectEnabled to use the Dynamic Routing feature.

Static Routing

A static route is a pre-determinedpathway that network information must travel to reach a specific host or network. Enter the information described below to set up a new static route.

Wireless-NBroadband Router with Storage Link

9

Chapter 3

Advanced Configuration

Route Entries  To set up a static route between the Router and another network, select a number from the dropdown list. ClickDelete This Entry to delete a static route.

Enter Route Name  Enter a name for the Route here, using a maximum of 25 alphanumeric characters.

Destination LAN IP  The Destination LAN IP is the address of the remote network or host to which you want to assign a static route.

Subnet Mask  The Subnet Mask determines which portion of a Destination LAN IP address is the network portion, and which portion is the host portion.

Gateway  This is the IP address of the gateway device that allows for contact between the Router and the remote network or host.

Interface  This interface tells you whether the Destination IP Address is on theLAN &Wireless (Ethernet and wireless networks) or theInternet (WAN).

Click Show Routing Table to view the static routes you have already set up.

Advanced Routing > Routing Table

Routing Table

For each route, the Destination LAN IP address, Subnet Mask, Gateway, and Interface are displayed. Click Refresh to update the information. ClickClose to exit this screen.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Wireless > Basic Wireless Settings

The basic settings for wireless networking are set on this screen.

There are two ways to configure the Router’s wireless network(s), manual and Wi-FiProtected Setup.

Wi-FiProtected Setup is a feature that makes it easy to set up your wireless network. If you have client devices, such as wireless adapters, that supportWi-FiProtected Setup, then you can useWi-FiProtected Setup.

Wireless Configuration  To manually configure your wireless network, selectManual. Proceed toBasic Wireless Settings,page 10. To useWi-FiProtected Setup,

select Wi-FiProtected Setup. Proceed to Wi-Fi Protected Setup, page 11.

Basic Wireless Settings

Wireless > Basic Wireless Settings (Manual Setup)

Network Mode  From thisdrop-downmenu, you can select the wireless standards running on your network. If you haveWireless-N,Wireless-G,andWireless-Bdevices in your network, keep the default,Mixed. If you have onlyWireless-GandWireless-Bdevices in your network, selectBG-Mixed.If you have onlyWireless-Ndevices, selectWireless-N Only. If you have onlyWireless-Gdevices, selectWireless-G Only. If you have onlyWireless-Bdevices, selectWireless-B Only. If you do not have any wireless devices in your network, selectDisabled.

Network Name (SSID)  The SSID is the network name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It iscase-sensitiveand must not exceed 32 characters (use any of the characters on the keyboard). Make sure this setting is the same for all points in your wireless network. For added security, you should change the default SSID (linksys) to a unique name.

Channel Width  For best performance in a network usingWireless-N,Wireless-GandWireless-Bdevices, selectWide - 40MHz Channel. ForWireless-GandWireless-Bnetworking only, keep the default,Standard - 20MHz Channel. If you are not sure which option to use, select

Auto.

NOTE: If you select Wide - 40MHz Channel for the Channel Width setting, thenWireless-Ncan use two channels: a primary one (Wide Channel) and a secondary one (Standard Channel). This will enhanceWireless-Nperformance.

Wide Channel  If Wide - 40MHz Channel is the Channel Width setting, then this setting will be available for your primaryWireless-Nchannel. Select any channel from thedrop-downmenu. If you are not sure which channel to select, keep the default,Auto.

Wireless-NBroadband Router with Storage Link

10

Chapter 3

Advanced Configuration

Standard Channel  If Standard - 20 MHz Channel is the Channel Width setting, then this setting will be available. Select the appropriate channel for your wireless network. If you are not sure which channel to select, then keep the default,Auto.

If Wide - 40MHz Channel is the Channel Width setting, then the Standard Channel will be a secondary channel for Wireless-N(2.4 GHz).

If you selected a specific channel for the Wide Channel setting, then the Standard Channel options will vary. Select the appropriate channel for your wireless network.

SSID Broadcast  When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router. To broadcast the Router’s SSID, keep the default,Enabled. If you do not want to broadcast the Router’s SSID, then selectDisabled.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Wi-FiProtected Setup

There are three methods available. Use the method that applies to the client device you are configuring.

Wireless > Basic Wireless Settings (Wi-FiProtected Setup)

Wi-FiProtected Setup Configured

NOTE: Wi-FiProtected Setup configures one client device at a time. Repeat the instructions for each client device that supportsWi-FiProtected Setup.

Method #1

Use this method if your client device has a Wi-FiProtected Setup button.

1.Click or press the Wi-Fi Protected Setup button on the client device.

2.Click the Wi Fi Protected Setup button on this screen.

3.After the client device has been configured, click OK. Then refer back to your client device or its documentation for further instructions.

Wi-FiProtected Setup > Congratulations

Method #2

Use this method if your client device has a Wi-FiProtected Setup PIN number.

1.Enter the PIN number in the field on this screen.

2.Click Register.

Wireless-NBroadband Router with Storage Link

11

Chapter 3

Advanced Configuration

3.After the client device has been configured, click OK. Then refer back to your client device or its documentation for further instructions.

Method #3

Use this method if your client device asks for the Router’s PIN number.

1.Enter the PIN number listed on this screen. (It is also listed on the label on the bottom of the Router.)

2.After the client device has been configured, click OK. Then refer back to your client device or its documentation for further instructions.

The Wi-FiProtected Setup Status, Network Name (SSID), Security, Encryption, and Passphrase are displayed at the bottom of the screen.

NOTE: If you have client devices that do not supportWi-FiProtected Setup, note the wireless settings, and then manually configure those client devices.

Wireless > Wireless Security

The Wireless Security screen configures the security of your wireless network. There are six wireless security mode options supported by the Router: WPA Personal, WPA Enterprise, WPA2 Personal, WPA2 Enterprise, RADIUS, and WEP. (WPA stands forWi-FiProtected Access, which is a security standard stronger than WEP encryption. WEP stands for Wired Equivalent Privacy, while RADIUS stands for Remote AuthenticationDial-InUser Service.) These six are briefly discussed here. For detailed instructions on configuring wireless security for the Router, refer to

Chapter 2: Wireless Security Checklist, page 3.

Wireless Security

Security Mode

Select the security method for your wireless network. If you do not want to use wireless security, keep the default,

Disabled.

WPA Personal

NOTE: If you are using WPA, then each device in your wireless network MUST use the same WPA method and shared key, or else the network will not function properly.

Security Mode > WPA Personal

Encryption   WPA supports two encryption methods, TKIP and AES, with dynamic encryption keys. Select the type of algorithm,TKIP orAES. The default isTKIP.

Passphrase  Enter a Passphrase of8-63characters.

Key Renewal  Enter a Key Renewal period, which instructs the Router how often it should change the encryption keys. The default is3600 seconds.

WPA2 Personal

Security Mode > WPA2 Personal

Encryption  WPA2 supports two encryption methods, TKIP and AES, with dynamic encryption keys. Select the type of algorithm,AES orTKIP or AES. The default isTKIP or AES.

Passphrase  Enter a Passphrase of8-63characters.

Key Renewal  Enter a Key Renewal period, which instructs the Router how often it should change the encryption keys. The default is3600 seconds.

Wireless-NBroadband Router with Storage Link

12

Chapter 3

Advanced Configuration

WPA Enterprise

This option features WPA used with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.)

Security Mode > WPA Enterprise

Encryption   WPA supports two encryption methods, TKIP and AES, with dynamic encryption keys. Select the type of algorithm,TKIP orAES. The default isTKIP.

RADIUS Server  Enter the IP address of the server.

RADIUS Port  Enter the port number of the server. The default is1812.

Shared Secret  Enter the key shared between the Router and the server.

Key Renewal  Enter a Key Renewal period, which instructs the Router how often it should change the encryption keys. The default is3600 seconds.

WPA2 Enterprise

This option features WPA2 used with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.)

Security Mode > WPA2 Enterprise

Encryption  WPA2 supports two encryption methods, TKIP and AES, with dynamic encryption keys. Select the type of algorithm,AES orTKIP or AES. The default isTKIP or AES.

RADIUS Server  Enter the IP address of the server.

RADIUS Port  Enter the port number of the server. The default is1812.

Shared Secret  Enter the key shared between the Router and the server.

Key Renewal  Enter a Key Renewal period, which instructs the Router how often it should change the encryption keys. The default is3600 seconds.

RADIUS

This option features WEP used with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.)

IMPORTANT: If you are using WEP, then each device in your wireless network MUST use the same WEP encryption method and key, or else the network will not function properly.

Security Mode > RADIUS

RADIUS Server  Enter the IP address of the server.

RADIUS Port  Enter the port number of the server. The default is1812.

Shared Secret  Enter the key shared between the Router and the server.

Encryption  Select a level of WEP encryption,

40/64 bits (10 hex digits) or 104/128 bits (26 hex digits). The default is 40/64 bits (10 hex digits).

Passphrase  Enter a Passphrase to automatically generate WEP keys. Then clickGenerate.

Key 1-4  If you did not enter a Passphrase, enter the WEP key(s) manually.

TX Key  Select which TX (Transmit) Key to use. The default is1.

Wireless-NBroadband Router with Storage Link

13

Chapter 3

Advanced Configuration

WEP

WEP is a basic encryption method, which is not as secure as WPA.

IMPORTANT: If you are using WEP encryption, then each device in your wireless network MUST use the same WEP encryption method and key, or else the network will not function properly.

Security Mode > WEP

Encryption  Select a level of WEP encryption,

40/64 bits (10 hex digits) or 104/128 bits (26 hex digits). The default is 40/64 bits (10 hex digits).

Passphrase  Enter a Passphrase to automatically generate WEP keys. Then clickGenerate.

Key 1-4  If you did not enter a Passphrase, enter the WEP key(s) manually.

TX Key  Select which TX (Transmit) Key to use. The default is1.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Wireless > Wireless MAC Filter

Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s radius.

Wireless > Wireless MAC Filter

Wireless MAC Filter

Enabled/Disabled  To filter wireless users by MAC Address, either permitting or blocking access, selectEnabled. If you do not wish to filter users by MAC Address, keep the default,

Disabled.

Access Restriction

Prevent  Select this option to block wireless access by MAC Address. This button is selected by default.

Permit  Select this option to allow wireless access by MAC Address. This button is not selected by default.

MAC Address Filter List

Wireless Client List  Click this to open theWireless Client List screen.

Wireless-NBroadband Router with Storage Link

14

Chapter 3

Advanced Configuration

Wireless Client List

Wireless Client List

This screen shows computers and other devices on the wireless network. The list can be sorted by Client Name, Interface, IP Address, MAC Address, and Status.

Select Save to MAC Address Filter Listfor any device you want to add to the MAC Address Filter List. Then click Add.

To update the on-screeninformation, clickRefresh. To exit this screen and return to theWireless MAC Filter screen, clickClose.

MAC 01-50  Enter the MAC addresses of the devices whose wireless access you want to block or allow.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Wireless > Advanced Wireless Settings

This Advanced Wireless Settings screen is used to set up the Router’s advanced wireless functions. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance.

Wireless > Advanced Wireless Settings

Advanced Wireless

AP Isolation  This isolates all wireless clients and wireless devices on your network from each other. Wireless devices will be able to communicate with the Router but not

with each other. To use this function, select Enabled. AP Isolation is disabled by default.

Authentication Type  The Authentication Type setting is available if the Security Mode is RADIUS or WEP. The default is set toAuto, which allows either Open System or Shared Key authentication to be used. With Open System authentication, the sender and the recipient do NOT use a WEP key for authentication. With Shared Key authentication, the sender and recipient use a WEP key for authentication. SelectShared Key to only use Shared Key authentication.

Basic Rate  The Basic Rate setting is not actually one rate of transmission but a series of rates at which the Router can transmit. (The Basic Rate is not the actual rate of data transmission. If you want to specify the Router’s rate of data transmission, configure the Transmission Rate setting.)The Router will advertise its Basic Rate to the other wireless devices in your network, so they know which rates will be used. The Router will also advertise that it will automatically select the best rate for transmission. The default setting isDefault, when the Router can transmit at all standard wireless rates(1-2Mbps, 5.5 Mbps, 11 Mbps, 18 Mbps, and 24Mbps). Select1-2Mbps for use with older wireless technology. SelectAll, when the Router can transmit at all wireless rates.

Transmission Rate  The Transmission setting is available if the Network Mode isBG-Mixed,Wireless-GOnly, orWireless-BOnly.The rate of data transmission should be set depending on the speed of your wireless network. Select from a range of transmission speeds, or keep the default,Auto, to have the Router automatically use the fastest possible data rate and enable theAuto-Fallbackfeature.Auto-Fallbackwill negotiate the best possible connection speed between the Router and a wireless client.

N Transmission Rate  The N Transmission setting is available if the Network Mode is Mixed orWireless-NOnly. The rate of data transmission should be set depending on the speed of yourWireless-Nnetworking. Select from a range of transmission speeds, or keep the default,Auto, to have the Router automatically use the fastest possible data rate and enable theAuto-Fallbackfeature. Auto Fallback will negotiate the best possible connection speed between the Router and a wireless client.

CTS Protection Mode  The Router automatically uses CTS(Clear-To-Send)ProtectionModewhenyourWireless-NandWireless-Gdevices are experiencing severe problems and are not able to transmit to the Router in an environment with heavy 802.11b traffic. This option boosts the Router’s ability to catch allWireless-NandWireless-Gtransmissions but severely decreases performance. To use this option, keep the default,Auto. To disable this option, select

Disabled.

Beacon Interval  Enter a value between 1 and 65,535 milliseconds. The Beacon Interval value indicates the

Wireless-NBroadband Router with Storage Link

15

Chapter 3

Advanced Configuration

frequency interval of the beacon. A beacon is a packet broadcast by the Router to synchronize the wireless network. The default is 100 milliseconds.

DTIM Interval  This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast and multicast messages. The default value is1.

Fragmentation Threshold  This value specifies the maximum size for a packet before data is fragmented into multiple packets. If you experience a high packet error rate, you may slightly increase the Fragmentation Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor reduction of the default value is recommended. In most cases, it should remain at its default value of 2346.

RTS Threshold  Should you encounter inconsistent data flow, only minor reduction of the default value,2347, is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. The RTS Threshold value should remain at its default value of

2347.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Security > Firewall

The Firewall screen is used to configure a firewall that can filter out various types of unwanted traffic on the Router’s local network.

Security > Firewall

Firewall

SPI Firewall Protection  To use firewall protection, keep the default selection,Enabled. To turn off firewall protection, selectDisabled.

Internet Filter

Filter Anonymous Internet Requests  This feature makes it more difficult for outside users to work their way into your network. This feature is selected by default. Deselect the feature to allow anonymous Internet requests.

Filter Multicast  Multicasting allows for multiple transmissions to specific recipients at the same time. If multicasting is permitted, then the Router will allow IP multicast packets to be forwarded to the appropriate computers. Select this option to filter multicasting. This feature is not selected by default.

Filter Internet NAT Redirection  This feature uses port forwarding to block access to local servers from local networked computers. Select this option to filter Internet NAT redirection. It is not selected by default.

Filter IDENT (Port 113)  This feature keeps port 113 from being scanned by devices outside of your local network. This feature is selected by default. Deselect this option to disable it.

Web Filter

Proxy  Use of WAN proxy servers may compromise the Gateway’s security. Denying Proxy will disable access to any WAN proxy servers. Select this option to enable proxy filtering. Deselect the feature to allow proxy access.

Java  Java is a programming language for websites. If you deny Java, you run the risk of not having access to Internet sites created using this programming language. Select this option to enable Java filtering. Deselect the feature to allow Java usage.

ActiveX  ActiveX is a programming language for websites. If you deny ActiveX, you run the risk of not having access to Internet sites created using this programming language. Select this option to enable ActiveX filtering. Deselect the feature to allow ActiveX usage.

Cookies  A cookie is data stored on your computer and used by Internet sites when you interact with them. Select this option to filter cookies. Deselect the feature to allow cookie usage.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Wireless-NBroadband Router with Storage Link

16

Chapter 3

Advanced Configuration

Security > VPN Passthrough

The VPN Passthrough screen allows you to enable VPN tunnels using IPSec, PPTP, or L2TP protocols to pass through the Router’s firewall.

Security > VPN Passthrough

VPN Passthrough

IPSec Passthrough  Internet Protocol Security (IPSec) is a suite of protocols used to implement secure exchange of packets at the IP layer. To allow IPSec tunnels to pass through the Router, keep the default,Enabled.

PPTP Passthrough  Point-to-PointTunneling Protocol (PPTP) allows thePoint-to-PointProtocol (PPP) to be tunneled through an IP network. To allow PPTP tunnels to pass through the Router, keep the default,Enabled.

L2TP Passthrough  Layer 2 Tunneling Protocol is the method used to enablePoint-to-Pointsessions via the Internet on the Layer 2 level. To allow L2TP tunnels to pass through the Router, keep the default,Enabled.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Storage > Disk

The storage options are available when a USB storage device is connected to the USB port of the Router. If the storage device does not fit (for example, it may block port 1), then use the included USB extension cable.

The Disk screen describes the disk currently attached to the Router. Use this screen to create shared folders, safely remove a disk, or format a disk (any data on the disk will be deleted during formatting).

Shared folders are folders you create to manage access to the folders on the disk. By default the Router creates a shared folder called Public, which includes all of the folders on the disk. For the Public folder, the admin group hasread-and-writeaccess rights, and the guest group hasread-onlyaccess rights. (By default the Router creates two user groups,admin andguest.)

Storage > Disk

Disk Management

If a formatted disk is connected to the Router, then its name is displayed. For each partition of the disk, the Partition, File System, Capacity, and Free Space information are displayed.

Safely Remove Disk  Before physically disconnecting a disk from the Router, clickSafely Remove Disk first. This prevents the possible loss of data, which may occur if you remove the disk while it is transferring data.

Create Share  To create a shared folder, click this option for the appropriate partition, and theShared Folder screen appears. Proceed toCreate or Edit a Shared Folder,page 18.

Shared Folder

Shared Disk IP Address  The IP address of the disk is displayed.

Summary  To view a list of shared folders, click this option. Proceed toShared Folders Summary,page 18.

For each shared folder, the Display Name, Partition, and Shared Folder location are displayed.

Edit  To change the access settings of a shared folder, click this option, and theShared Folder screen appears. Proceed toCreate or Edit a Shared Folder,page 18.

Delete  To delete a shared folder, click this option.

Wireless-NBroadband Router with Storage Link

17

Chapter 3

Advanced Configuration

Shared Folders Summary

The Shared Folders Summary screen displays the following information: Display Name, Partition, Shared Folder, and Groups with Access.

Summary

To exit the Shared Folders Summary screen and return to theDisk Management screen, clickClose.

Format Disk

Disk  To format a disk and create a new partition, select the disk you want to format, and then clickFormat Disk. (If your disk was formatted with multiple partitions, then the formatting will delete them and create a single partition.) TheClaim Disk screen appears.

Claim Disk

Enter a partition’s name  Create a name for the partition.

To format the disk as FAT32, click Format and follow the on screen instructions. To cancel the formatting, clickCancel. To update theon-screeninformation, click

Refresh.

Claim Disk

On the Disk Management screen, clickRefresh to update theon-screeninformation.

Create or Edit a Shared Folder

Use this screen to add a shared folder.

Shared Folder

Display Name

Create a name for the shared folder.

Partition

The name of the partition is displayed.

Share enter Partition  Select this option if the shared folder should include the entire partition.

If you do not want to share the entire partition, then select the folder you do want to share.

Current Folder  The current folder is displayed.Folder  The available folders are listed by Folder name.

Enter into Folder  To displaysub-folders,click this button.

Select  Select a folder.

Return to Upper Folder  To return to the previous folder, click this button.

Access

Specify which user groups have read-and-writeor readonly access to the shared folders. (To create user groups, refer toCreate or Edit a Group Account,page 20.)

Available Groups  To allow a group access to the shared folder, select it, and then click the>> button.

Groups with Access  To block a group from accessing the shared folder, select it, and then click the<< button.

Wireless-NBroadband Router with Storage Link

18

Chapter 3

Advanced Configuration

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes. ClickClose to exit the screen.

Storage > Media Server

The storage options are available when a USB storage device is connected to the USB port of the Router. If the storage device does not fit (for example, it may block port 1), then use the included USB extension cable.

Storage > Media Server

UPnP Media Server

If you have UPnP AV-enabled(orDLNA-certified)devices in your home, then you can use the Router as a media server. Examples of UPnPAV-enableddevices include a digital media adapter, a gaming console with abuilt-inmedia player, or a digital picture frame.

For example, if you have a digital media adapter that sends content to your entertainment system, then the digital media adapter can locate the Router using the UPnP AV standard. The folders you specify can then be accessed and played by the digital media adapter.

Setup

Server Name  The default server name of the Router isWRT160NL. You can change this name on theStorage > Administration screen; refer toStorage > Administration,page 20.

UPnP Media Server  To use the Router’s media server function, selectEnabled. Otherwise, selectDisabled.

Database Setup

Specify Folder to Scan  To add a media folder to the database of the Router’s media server, click this button. TheMedia Folder screen appears. Proceed toCreate a Media Folder,page 19.

Auto-scan every __  To automatically scan the media folders, select this option. Then select the appropriate interval:2 Hours (default),6 Hours,12 Hours,24 Hours, or48 Hours.

Scan All  To scan all media files, click this button.

The database table lists the media folders with the following information: Name, Partition, and Folder.

Scan  To scan a folder, clickScan.Delete  To delete a folder, clickDelete.

Create a Media Folder

Use this screen to add a media folder.

Media Folder

Display Name

Create a name for the media folder.

Partition

The name of the partition is displayed.

Share enter Partition  Select this option if the media folder should include the entire partition.

If you do not want to share the entire partition, then select the folder you do want to share.

Current Folder  The current folder is displayed.Folder  The available folders are listed by Folder name.

Enter into Folder  To displaysub-folders,click this button.

Select  Select a folder.

Return to Upper Folder  To return to the previous folder, click this button.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes. ClickClose to exit the screen.

On the Media Server screen, clickSave Settings to apply your changes, or clickCancel Changes to clear your changes.

Wireless-NBroadband Router with Storage Link

19

Chapter 3

Advanced Configuration

Storage > Administration

The Administration screen allows you to manage the user groups and individual users who can access the shared folders.

Storage > Administration

Information

Server Name  Enter the server name for the Router; it will be used for the disk and media server features. Use only alphanumeric characters (letters A to Z and numbers 0 to 9) in the server name. The default isWRT160NL.

Workgroup Name  Enter the workgroup name for the Router; it should match the workgroup name of the computers on your local network. The Router’s default isworkgroup.

Server LAN IP Address  The local IP address of the Router is displayed.

Server Internet IP Address  The Internet IP address of the Router is displayed.

Group Management

By default the Router creates two user groups, admin andguest.

The groups are listed by Group Name and Access level. There are two levels of access, r & w (read-and-write)and r(read-only).

Create New Group  To create a new group of users, click this button. TheGroup Account screen appears. Proceed to

Create or Edit a Group Account, page 20.

Edit  To change the description or access rights of a group, clickModify, and theGroup Account screen appears. Proceed toCreate or Edit a Group Account,page 20.

Delete  To delete a group, click this button.

User Management

By default the Router creates two users, admin andguest.

The users are listed by User Name and Group.

Create New User  To create a new user, click this button. TheUser Account screen appears. Proceed toCreate or Edit a User Account,page 21.

Edit  To change the settings of a user account, clickModify, and theUser Account screen appears. Proceed to

Create or Edit a User Account, page 21.

Delete  To delete a user, click this button.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Create or Edit a Group Account

Group Account

Group Account

Group Name  Create a name for the group.Description  Enter keywords to describe the group.

Access  Select the appropriate level of access,read and write orread only.

Click Create orModify to apply your changes, or clickCancel to clear your changes. ClickClose to exit the screen.

Wireless-NBroadband Router with Storage Link

20

Chapter 3

Advanced Configuration

Create or Edit a User Account

User Account

User Account

Name  Create a name for the user.

Full Name  Enter the actual name of the user.Description  Enter keywords to describe the user.

Password  Enter the password that the user will use for login

Confirm Password  Enter the password again to confirm.Group Member  Select the appropriate user group.

Account disabled  To temporarily disable an account, select this option.

Click Create Useror Modify Userto apply your changes, or click Cancelto clear your changes. Click Closeto exit the screen.

On the Media Server screen, clickSave Settings to apply your changes, or clickCancel Changes to clear your changes.

Access Restrictions > Internet Access

The Internet Access screen allows you to block or allow specific kinds of Internet usage and traffic, such as Internet access, designated services, and websites during specific days and times.

Access Restrictions > Internet Access

Internet Access Policy

Access Policy  Access can be managed by a policy. Use the settings on this screen to establish an access policy (afterSave Settings is clicked). Selecting a policy from the dropdown menu will display that policy’s settings. To delete a policy, select that policy’s number and clickDelete This Policy. To view all the policies, clickSummary.

Summary

The policies are listed with the following information: No., Policy Name, Access, Days, Time, and status (Enabled). To enable a policy, select Enabled. To delete a policy, clickDelete. ClickSave Settings to save your changes, or clickCancel Changes to clear your changes. To return to the

Internet Access Policy screen, click Close.

Summary

Wireless-NBroadband Router with Storage Link

21

Chapter 3

Advanced Configuration

Status  Policies are disabled by default. To enable a policy, select the policy number from thedrop-downmenu, and selectEnabled.

To create a policy, follow steps 1-11.Repeat these steps to create additional policies, one at a time.

1.Select a number from the Access Policy drop-downmenu.

2.Enter a Policy Name in the field provided.

3.To enable this policy, select Enabled.

4.Click Edit List to select which PCs will be affected by the policy. TheList of PCs screen appears. You can select a PC by MAC address or IP address. You can also enter a range of IP addresses if you want this policy to affect a group of PCs. After making your changes, clickSave Settings to apply your changes, or clickCancel Changes to clear your changes. Then clickClose.

List of PCs

5.Select the appropriate option, Deny orAllow, depending on whether you want to block or allow Internet access for the PCs you listed on theList of PCs screen.

6.Decide which days and what times you want this policy to be enforced. Select the individual days during which the policy will be in effect, or select Everyday. Then enter a range of hours and minutes during which the policy will be in effect, or select24 Hours.

7.You can block websites with specific URL addresses. Enter each URL in a separate Website Blocking by URL Address field.

8.You can also block websites using specific keywords. Enter each keyword in a separate Website Blocking by Keyword field.

9.You can filter access to various services accessed

over

the

Internet,

such

as FTP or telnet. (You

can

block

up to

three

applications per policy.)

From the Applications list, select the application you want to block. Then click the >> button to move it to

the Blocked List. To remove an application from the Blocked List, select it and click the << button.

10.If the application you want to block is not listed or you want to edit a service’s settings, enter the application’s name in the Application Name field. Enter its range in thePort Range fields. Select its protocol from theProtocol drop-downmenu. Then clickAdd.

To modify a service, select it from the Application list. Change its name, port range, and/or protocol setting. Then click Modify.

To delete a service, select it from the Application list. Then click Delete.

11.Click Save Settings to save the policy’s settings, or clickCancel Changes to clear the changes.

Applications and Gaming > Single Port

Forwarding

The Single Port Forwarding screen allows you to customize port services for common applications on this screen.

When users send these types of requests to your network via the Internet, the Router will forward those requests to the appropriate servers (computers). Before using forwarding, you should assign static IP addresses to the designated servers (use the DHCP Reservation feature on the Basic Setup screen; refer toDHCP Reservation,page 7).

Applications and Gaming > Single Port Forwarding

Single Port Forwarding

Common applications are available for the first five entries. Select the appropriate application. Then enter the IP address of the server that should receive these requests. Select Enabled to activate this entry.

For additional applications, complete the following fields:

Application Name  Enter the name you wish to give the application. Each name can be up to 12 characters.

Wireless-NBroadband Router with Storage Link

22

Chapter 3

Advanced Configuration

External Port  Enter the external port number used by the server or Internet application. Check with the Internet application documentation for more information.

Internal Port  Enter the internal port number used by the server or Internet application. Check with the Internet application documentation for more information.

Protocol  Select the protocol(s) used for this application,

TCP, UDP, or Both.

To IP Address  For each application, enter the IP address of the PC that should receive the requests. If you assigned a static IP address to the PC, then you can clickDHCP Reservation on theBasic Setup screen to look up its static IP address.

Enabled  For each application, selectEnabled to enable port forwarding.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Applications and Gaming > Port Range

Forwarding

The Port Range Forwarding screen allows you to set up public services on your network, such as web servers, ftp servers,e-mailservers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming. Some Internet applications may not require any forwarding.)

When users send these types of requests to your network via the Internet, the Router will forward those requests to the appropriate servers (computers). Before using forwarding, you should assign static IP addresses to the designated servers (use the DHCP Reservation feature on the Basic Setup screen; refer toDHCP Reservation,page 7).

If you need to forward all ports to one computer, click the DMZ tab.

Applications and Gaming > Port Range Forwarding

Port Range Forwarding

To forward a port, enter the information on each line for the criteria required.

Application Name  In this field, enter the name you wish to give the application. Each name can be up to 12 characters.

Start~End Port  Enter the number or range of port(s) used by the server or Internet applications. Check with the Internet application documentation for more information.

Protocol  Select the protocol(s) used for this application,

TCP, UDP, or Both.

To IP Address  For each application, enter the IP address of the PC running the specific application. If you assigned a static IP address to the PC, then you can clickDHCP Reservation on theBasic Setup screen to look up its static IP address.

Enabled  SelectEnabled to enable port forwarding for the applications you have defined.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Applications & Gaming > Port Range

Triggering

The Port Range Triggering screen allows the Router to watch outgoing data for specific port numbers. The IP address of the computer that sends the matching data is remembered by the Router, so that when the requested data returns through the Router, the data is pulled back to the proper computer by way of IP address and port mapping rules.

Applications and Gaming > Port Range Triggering

Port Range Triggering

Application Name  Enter the application name of the trigger.

Wireless-NBroadband Router with Storage Link

23

Chapter 3

Advanced Configuration

Triggered Range  For each application, enter the starting and ending port numbers of the triggered port number range. Check with the Internet application documentation for the port number(s) needed.

ForwardedRange  Foreachapplication,enterthestarting and ending port numbers of the forwarded port number range. Check with the Internet application documentation for the port number(s) needed.

Enabled  SelectEnabled to enable port triggering for the applications you have defined.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Applications and Gaming > DMZ

The DMZ feature allows one network computer to be exposed to the Internet for use of a special-purposeservice such as Internet gaming or videoconferencing. DMZ hosting forwards all the ports at the same time to one PC. The Port Range Forwarding feature is more secure because it only opens the ports you want to have opened, while DMZ hosting opens all the ports of one computer, exposing the computer to the Internet.

Applications and Gaming > DMZ

DMZ

Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP address assigned to it because its IP address may change when using the DHCP function.

Enabled/Disabled  To disable DMZ hosting, selectDisabled. To expose one PC, selectEnabled. Then configure the following settings:

Source IP Address  If you want any IP address to be the source, selectAny IP Address. If you want to specify an IP address or range of IP addresses as the designated source, select and complete the IP address range fields.

Destination  If you want to specify the DMZ host by IP address, selectIP Address and enter the IP address in the field provided. If you want to specify the DMZ host by MAC address, selectMAC Address and enter the MAC

address in the field provided. To retrieve this information, click DHCP Client Table.

DMZ > DHCP Client Table

DHCP Client Table

The DHCP Client Table lists computers and other devices that have been assigned IP addresses by the Router. The list can be sorted by Client Name, Interface, IP Address, MAC Address, and Expired Time (how much time is left for the current IP address). To select a DHCP client, click Select. To update the onscreen information, clickRefresh. To exit this screen and return to theDMZ screen, clickClose.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Applications and Gaming > QoS

Quality of Service (QoS) ensures better service to high-prioritytypes of network traffic, which may involve demanding,real-timeapplications, such as videoconferencing.

Applications and Gaming > QoS

QoS (Quality of Service)

Wireless

You can configure the support and No Acknowledgement settings in this section.

WMM Support  If you have other devices that support Wi Fi Multimedia (WMM) on your network, keep the default,Enabled. Otherwise, selectDisabled.

Wireless-NBroadband Router with Storage Link

24

Chapter 3

Advanced Configuration

No Acknowledgement  If you want to disable the Router’s Acknowledgement feature, so the Router will notre-senddata if an error occurs, then selectEnabled. Otherwise, keep the default,Disabled.

Internet Access Priority

In this section, you can set the bandwidth priority for a variety of applications and devices. There are four levels priority: High, Medium, Normal, or Low. When you set priority, do not set all applications to High, because this will defeat the purpose of allocating the available bandwidth. If you want to select below normal bandwidth, select Low. Depending on the application, a few attempts may be needed to set the appropriate bandwidth priority.

Enabled/Disabled  To use the QoS policies you have set, keep the default,Enabled. Otherwise, selectDisabled.

Category

There are four categories available. Select one of the following: Applications,Online Games,MAC Address,

EthernetPort,orVoiceDevice.Proceedtotheinstructions for your selection.

Summary

This lists the QoS entries you have created for your applications and devices. Refer to Summary,page 26 for more information.

Applications

Applications  Select the appropriate application. If you select Add a New Application, follow the Add a New Application instructions.

Priority  Select the appropriate priority:High,Medium,

Normal, or Low.

Click Add to save your changes.Your new entry will appear in the Summary list.

Add a New Application

QoS > Add a New Application

Enter a Name  Enter any name to indicate the name of the entry.

Port Range  Enter the port range that the application will be using. For example, if you want to allocate bandwidth for FTP, you can enter21-21.If you need services for an application that uses from 1000 to 1250, you enter 1000-

1250 as your settings. You can have up to three ranges to define for this bandwidth allocation. Port numbers can range from 1 to 65535. Check your application’s documentation for details on the service ports used.

Select the protocol TCP orUDP, or selectBoth.

Priority  Select the appropriate priority:High,Medium (Recommend),Normal, orLow.

Click Add to save your changes.Your new entry will appear in the Summary list.

Online Games

QoS > Online Games

Games  Select the appropriate game. If you select Add a New Game, follow the Add a New Game instructions.

Priority  Select the appropriate priority:High,Medium (Recommend),Normal, orLow.

Click Add to save your changes.Your new entry will appear in the Summary list.

Add a New Game

QoS > Add a New Game

Enter a Name  Enter any name to indicate the name of the entry.

Port Range  Enter the port range that the game will be using. You can have up to three ranges to define for this bandwidth allocation. Port numbers can range from 1 to 65535. Check your application’s documentation for details on the service ports used.

Select the protocol TCP orUDP, or selectBoth.

Priority  Select the appropriate priority:High,Medium (Recommend),Normal, orLow.

Click Add to save your changes.Your new entry will appear in the Summary list.

Wireless-NBroadband Router with Storage Link

25

Chapter 3

Advanced Configuration

MAC Address

QoS > MAC Address

Enter a Name  Enter a name for your device.

MAC Address  Enter the MAC address of your device.

Priority  Select the appropriate priority:High,Medium (Recommend),Normal, orLow.

Click Add to save your changes.Your new entry will appear in the Summary list.

Ethernet Port

QoS > Ethernet Port

Ethernet  Select the appropriate Ethernet port.

Priority  Select the appropriate priority:High,Medium (Recommend),Normal, orLow.

Click Add to save your changes.Your new entry will appear in the Summary list.

Voice Device

QoS > Voice Device

Enter a Name  Enter a name for your voice device.

MAC Address  Enter the MAC address of your voice device.

Priority  Select the appropriate priority:High (Recommend),Medium,Normal, orLow.

Click Add to save your changes.Your new entry will appear in the Summary list.

Summary

This lists the QoS entries you have created for your applications and devices.

Priority  This column displays the bandwidth priority of High, Medium, Normal, or Low.

Name  This column displays the application, device, or port name.

Information  This column displays the port range or MAC address entered for your entry. If apre-configuredapplication or game was selected, there will be no valid entry shown in this section.

Remove  Click this button to remove an entry.Edit  Click this button to make changes.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Administration > Management

The Administration > Managementscreen allows the network’s administrator to manage specific Router functions for access and security.

Administration > Management

Management

Router Access

To ensure the Router’s security, you will be asked for your password when you access the Router’s web-basedutility. The default isadmin.

Router Password  Enter a new password for the Router.

Re-enter to confirm  Enter the password again to confirm.

Local Management Access

Access via  HTTP (HyperText Transport Protocol) is the communications protocol used to connect to servers on the World Wide Web. HTTPS uses SSL (Secured Socket Layer) to encrypt data transmitted for higher security. SelectHTTP orHTTPS.HTTP is the default.

Wireless-NBroadband Router with Storage Link

26

Chapter 3

Advanced Configuration

Access via Wireless  If you are using the Router in a public domain where you are giving wireless access to your guests, you can disable wireless access to the Router’sweb-basedutility. You will only be able to access the utility via a wired connection if you disable the setting. Keep the default,Enabled, to allow wireless access to the utility, or selectDisabled to block wireless access to the utility.

Remote Access

Remote Management  To permit remote access of the Router, from outside the local network, selectEnabled. Otherwise, keep the default,Disabled.

Access viaHTTP (HyperText Transport Protocol) is the communications protocol used to connect to servers on the World Wide Web. HTTPS uses SSL (Secured Socket Layer) to encrypt data transmitted for higher security. SelectHTTP orHTTPS.HTTP is the default.

Remote Upgrade  If you want to be able to upgrade the Router remotely, from outside the local network, selectEnabled. (You must have the Remote Management feature enabled as well.) Otherwise, keep the default,

Disabled.

Allowed Remote IP Address  If you want to be able to access the Router from any external IP address, select Any IP Address. If you want to specify an external IP address or range of IP addresses, then select the second option and complete the fields provided.

Remote Management Port  Enter the port number that will be open to outside access.

NOTE: When you are in a remote location and wish to manage the Router, enterhttp://xxx.xxx.xxx.xxx:yyyy orhttps://xxx.xxx.xxx.xxx:yyyy, depending on whether you use HTTP or HTTPS. Enter the Router’s specific Internet IP address in place of xxx.xxx.xxx.xxx, and enter the Remote Management Port number in place of yyyy.

UPnP

Universal Plug and Play (UPnP) allows the appropriate Windows operating system to automatically configure the Router for various Internet applications, such as gaming and videoconferencing.

UPnP  If you want to use UPnP, keep the default,Enabled. Otherwise, selectDisabled.

Allow Users to Configure  Keep the default,Enabled, if you want to be able to make manual changes to the Router while using the UPnP feature. Otherwise, select

Disabled.

Allow Users to Disable Internet Access  Select Enabled, if you want to be able to prohibit any and all Internet connections. Otherwise, keep the default, Disabled.

Backup and Restore

Backup Configurations  To back up the Router’s configuration settings, click this button and follow the on screen instructions.

Restore Configurations  To restore the Router’s configuration settings, click this button and follow the onscreen instructions. (You must have previously backed up the Router’s configuration settings.)

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Administration > Log

The Router can keep logs of all traffic for your Internet connection.

Administration > Log

Log

Log  To disable the Log function, selectDisabled. To monitor traffic between the network and the Internet, keep the default,Enabled. With logging enabled, you can choose to view temporary logs.

View Log  To view the logs, clickView Log.

Log > View Log

Wireless-NBroadband Router with Storage Link

27

Chapter 3

Advanced Configuration

Log

•• Type  Select Incoming Log, Outgoing Log, Security Log, or DHCP Client Log.

•• <Type> Log  The Incoming Log displays a temporary log of the source IP addresses and destination port numbers for the incoming Internet traffic. The Outgoing Log displays a temporary log of the local IP addresses, destination URLs/IP addresses, and service/ port numbers for the outgoing Internet traffic. The Security log displays the login information for theweb-basedutility. The DHCP Client Log displays the LAN DHCP server status information.

Click Save the Log to save this information to a file on your PC’s hard drive. ClickRefresh to update the log. ClickClear to clear all the information that is displayed.

Click Save Settings to apply your changes, or clickCancel Changes to clear your changes.

Administration > Diagnostics

The diagnostic tests (Ping and Traceroute) allow you to check the connections of your network devices, including connection to the Internet.

Administration > Diagnostics

Diagnostics

Ping Test

Ping checks the status of a connection.

IP or URL Address  Enter the address of the PC whose connection you wish to test.

Packet Size  Enter the packet size you want to use. The default is32 bytes.

Number to Ping  Enter the number of times you wish to test the connection. The default is5.

Start Test  To run the test, click this button. ThePing screen shows if the test is successful. ClickClose to return to theDiagnostics screen. ClickStop to stop the test.

Diagnostics > Ping

Traceroute Test

Traceroute checks the performance of a connection.

IP or URL Address  Enter the address of the PC whose connection you wish to test.

Start Test  To run the test, click this button. TheTraceroute screen shows if the test is successful. ClickClose to return to theDiagnostics screen. ClickStop to stop the test.

Diagnostics > Traceroute

Administration > Factory Defaults

Restore the Router to its factory default settings.

Administration > Factory Defaults

NOTE: Do not restore the factory defaults unless you are having difficulties with the Router and have exhausted all other troubleshooting measures. Once the Router is reset, you will have tore-enterall of your configuration settings.

Factory Defaults

Restore All Settings  To reset the Router’s settings to the defaults, click this button and then follow the on screen instructions. Any settings you have saved will be lost when the default settings are restored.

Wireless-NBroadband Router with Storage Link

28

Chapter 3

Advanced Configuration

Administration > Firmware Upgrade

The Firmware Upgrade screen allows you to upgrade the Router’s firmware. Do not upgrade the firmware unless you are experiencing problems with the Router or the new firmware has a feature you want to use.

Administration > Firmware Upgrade

NOTE: The Router may lose the settings you have customized. Before you upgrade its firmware, write down all of your custom settings. After you upgrade its firmware, you will have to re enter all of your configuration settings.

Firmware Upgrade

Before upgrading the firmware, download the Router’s firmware upgrade file from the Linksys website, www.linksysbycisco.com.

Please select a file to upgrade the firmware  Click

Browse and select the firmware upgrade file.

Start to Upgrade  After you have selected the appropriate file, click this button, and follow theon-screeninstructions.

Status > Router

The Router screen displays information about the Router and its current settings.

Status > Router

Router Information

Firmware Version  The version number of the Router’s current firmware is displayed.

Firmware Verification  The unique identifier that verifies that you have valid firmware is displayed.

Current Time  The time set on the Router is displayed.

Internet MAC Address  The Router’s MAC Address, as seen by your ISP, is displayed.

Host Name  The Host Name of the Router is displayed (if it was entered on theSetup > Basic Setup screen).

Domain Name  The Domain Name of the Router is displayed (if it was entered on theSetup > Basic Setup screen).

Internet Connection

This section shows the current network information stored in the Router. The information varies depending on the Internet connection type selected on the Setup > Basic Setup screen.

Select Release IP Addressor Renew IP Addressas appropriate to release or renew a DHCP lease.

Click Refresh to update theon-screeninformation.

Wireless-NBroadband Router with Storage Link

29

Chapter 3

Advanced Configuration

Status > Local Network

The Local Network screen displays information about the local, wired network.

Status > Local Network

Local Network

Local MAC Address  The MAC address of the Router’s local, wired interface is displayed.

Router IP Address  The Router’s IP address, as it appears on your local network, is displayed.

Subnet Mask  The Subnet Mask of the Router is displayed.

DHCP Server

DHCP Server  The status of the Router’s DHCP server function is displayed.

Start IP Address  For the range of IP addresses used by devices on your local network, the starting IP address is displayed.

End IP Address  For the range of IP addresses used by devices on your local network, the ending IP address is displayed.

DHCP Clients Table  Click this button to view a list of computers or other devices that are using the Router as a DHCP server.

DHCP Clients Table

DHCP Client Table

The DHCP Client Table lists computers and other devices that have been assigned IP addresses by the Router. The list can be sorted by IP Address, MAC Address, Interface, and Client Name. To remove a DHCP client, click Delete. To update theon-screeninformation, clickRefresh. To exit this screen and return to theLocal Network screen, clickClose.

Status > Wireless Network

The Wireless Network screen displays information about your wireless network.

Status > Wireless

Wireless Network

MAC Address  The MAC address of the Router’s local, wireless interface is displayed.

Mode  The wireless mode used by the network is displayed.

Network Name (SSID)  The name of the wireless network, which is also called the SSID, is displayed.

Channel Width  The Channel Width setting (selected on theWireless > Basic Wireless Settings screen) is displayed.

Wide Channel  The Wide Channel setting (selected on theWireless > Basic Wireless Settings screen) is displayed.

Standard Channel  The Standard Channel setting (selected on theWireless > Basic Wireless Settings screen) is displayed.

Security  The wireless security method used by the Router is displayed.

SSID Broadcast  The status of the SSID Broadcast feature is displayed.

Wireless-NBroadband Router with Storage Link

30

Appendix A

Troubleshooting

Appendix A:

Troubleshooting

Your computer cannot connect to the Internet.

Follow these instructions until your computer can connect to the Internet:

•• Make sure that the Router is powered on. The Power LED should be green and not flashing.

•• If the Power LED is flashing, then power off all of your network devices, including the modem, Router, and computers. Then power on each device in the following order:

1.Cable or DSL modem

2.Router

3.Computer

•• Check the cable connections. The computer should be connected to one of the ports numbered1-4on the Router, and the modem must be connected to the Internet port on the Router.

The modem does not have an Ethernet port.

The modem is a dial-upmodem for traditionaldial-upservice. To use the Router, you need a cable/DSL modem andhigh-speedInternet connection.

You cannot use the DSL service to connect manually to the Internet.

After you have installed the Router, it will automatically connect to your Internet Service Provider (ISP), so you no longer need to connect manually.

The DSL telephone line does not fit into the Router’s Internet port.

The Router does not replace your modem. You still need your DSL modem in order to use the Router. Connect the telephone line to the DSL modem, and then insert the setup CD into your computer. Click Setup and follow the on screen instructions.

When you double-clickthe web browser, you are prompted for a username and password. If you want to get rid of the prompt, follow these instructions.

Launch the web browser and perform the following steps (these steps are specific to Internet Explorer but are similar for other browsers):

1.Select Tools> Internet Options.

2.Click the Connections tab.

3.Select Never dial a connection.

4. Click OK.

The Router does not have a coaxial port for the cable connection.

The Router does not replace your modem. You still need your cable modem in order to use the Router. Connect your cable connection to the cable modem, and then insert the setup CD into your computer. Click Setup and follow the on screen instructions.

The computer cannot connect wirelessly to the network.

Make sure the wireless network name or SSID is the same on both the computer and the Router. If you have enabled wireless security, then make sure the same security method and key are used by both the computer and the Router.

You need to modify the settings on the Router.

Open the web browser (for example, Internet Explorer or Firefox), and enter the Router’s IP address in the address field (the default IP address is 192.168.1.1). When prompted, enter the password to the Router (the default isadmin). Click the appropriate tab to change the settings.

The Router does not recognize your USB storage device.

Make sure the USB storage device uses the NTFS or FAT format. To check its format, follow these instructions:

1.Connect the USB storage device directly to your computer.

2.On your desktop, double-clickComputer orMy Computer icon.

3.Right-clickthe USB storage device, and click

Properties.

4. The format is listed in the File system description. If the format is not NTFS or FAT, then back up the data on the USB storage device.

After you have backed up the data on the USB storage drive, you can format it. Right-clickthe USB storage device, and clickFormat. Follow theon-screeninstructions. For more information, refer to Windows Help.

If the Router still does not recognize the USB storage device, then remove the power adapter from the Router’s Power port. Wait five seconds, and then re-connectthe power adapter to the Router’s Power port.

In Windows Vista, you do not see the USB storage device in the Network screen.

Make sure the Router and your computer use the same workgroup name. (The default workgroup name of the Router is workgroup. In Windows Vista,right-clickthe

Computer icon and select Properties. Click Advanced

Wireless-NBroadband Router with Storage Link

31

Appendix A

Troubleshooting

system settings. Click the Computer Nametab. The workgroup name is displayed.) If they differ, then change the workgroup name of the Router. Follow these instructions:

1.Access the web-basedutility of the Router. (Refer to

Chapter 3: Advanced Configuration, page 4.)

2.Click the Storage tab.

3.Click the Administrationtab.

4.In the Workgroup field, enter the workgroup name of your computer.

5.Click Save Settings.

In Windows XP, you do not see the Router in the My Network Places screen.

In the Network Tasks section, clickShow icons for networked UPnP devices. If the Router does not appear, follow these instructions:

1.Go to Start > Control Panel > Firewall.

2.Click the Exceptions tab.

3.Select UPnP Framework.

4.Click OK.

In Windows XP, you do not see your USB storage device in the View workgroup computers screen.

Make sure the Router and your computer use the same workgroup name. (The default workgroup name of the Router is workgroup. In Windows XP, go toStart > Control Panel > System. Click theComputer Name tab. The workgroup name is displayed.) If they differ, then change the workgroup name of the Router. Follow these instructions:

1.Access the web-basedutility of the Router. (Refer to

Chapter 3: Advanced Configuration, page 4.)

2.Click the Storage tab.

3.Click the Administrationtab.

4.In the Workgroup field, enter the workgroup name of your computer.

5.Click Save Settings.

WEB: If your questions are not addressed here, refer to the Linksys website,www.linksysbycisco.com

Wireless-NBroadband Router with Storage Link

32

Appendix B

How to Install and Access USB Storage

Appendix B: How to Install and Access USB Storage

Overview

This appendix explains how to do the following:

•• connect and access a USB storage device

•• map a shortcut to a USB storage device

•• create a shared folder on a USB storage device (advanced users)

•• manage access to shared folders using group and user accounts (advanced users)

Install the USB Storage Device

1.Make sure your computer has a wired or wireless connection to the Router.

2.Connect an external USB hard disk drive or USB flash disk to the USB port of the Router.

Access the USB Storage Device

Follow the instructions for your Windows operating system, Vista or XP.

Windows Vista

1. On your desktop, double-clicktheComputer icon.

Computer Icon

NOTE: If the Computer icon is not displayed, then go toStart > All Programs > Accessories

>Windows Explorer.

2.In the Address field, enter the server name of the Router:

\\<server_name_of_Router>

Enter Server Name of Router

ThedefaultservernameoftheRouterisWRT160NL.You can change this name on theStorage > Administration screen; refer toStorage > Administration,page 20.

NOTE: Another option is to use the IP address of the Router. In theAddress field, enter the local IP address of the Router:

\\xxx.xxx.xxx.xxx

The default is 192.168.1.1. You can change this IP address on theSetup > Basic Setup screen; refer toSetup > Basic Setup,page 4.

3.On the login screen, enter your account user name and password. (For the admin account, admin is both the default user name and password.)

Enter Account User Name and Password

User accounts are set up on the Storage>Administration screen; for more information, refer toCreate a User Account,page 38.

Windows XP

1.On your desktop, double-clicktheMy Computer icon.

My Computer Icon

NOTE:IftheMyComputericonisnotdisplayed, then go toStart > All Programs > Accessories

>Windows Explorer.

2.In the Address field, enter the server name of the Router:

\\<server_name_of_Router>

Enter Server Name of Router

ThedefaultservernameoftheRouterisWRT160NL.You can change this name on theStorage > Administration screen; refer toStorage > Administration,page 20.

Wireless-NBroadband Router with Storage Link

33

Appendix B

How to Install and Access USB Storage

NOTE: Another option is to use the IP address of the Router. In theAddress field, enter the local IP address of the Router:

\\xxx.xxx.xxx.xxx

The default is 192.168.1.1. You can change this IP address on theSetup > Basic Setup screen; refer toSetup > Basic Setup,page 4.

3.Enter your account user name and password. (For the admin account, admin is both the default user name and password.)

Enter Account User Name and Password

User accounts are set up on the Storage>Administration screen; for more information, refer toCreate a User Account,page 38.

Create a Shortcut to a Shared Folder

You can map any folder of the USB storage device as a separate drive. Follow the instructions for your Windows operating system, Vista or XP.

Windows Vista

Map a Drive

1. On your desktop, double-clicktheNetwork icon.

Network Icon

NOTE:IftheMyComputericonisnotdisplayed, then go toStart > All Programs > Accessories > Windows Explorer.

2.In the Address field, enter the server name of the Router:

\\<server_name_of_Router>

Enter Server Name of Router

ThedefaultservernameoftheRouterisWRT160NL.You can change this name on theStorage > Administration screen; refer toStorage > Administration,page 20.

NOTE: Another option is to use the IP address of the Router. In theAddress field, enter the local IP address of the Router:

\\xxx.xxx.xxx.xxx

The default is 192.168.1.1. You can change this IP address on theSetup > Basic Setup screen; refer toSetup > Basic Setup,page 4.

3.Right-clickthe folder you want to share, and clickMap Network Drive. (The default shared folder is named

Public.)

Map Network Drive

Wireless-NBroadband Router with Storage Link

34

Appendix B

How to Install and Access USB Storage

4.From the Drive drop-downmenu, select an available drive letter.

Select Drive Letter

5. Click Finish.

Access Mapped Drive

1. On your desktop, double-clicktheComputer icon.

Computer Icon

NOTE: If the Computer icon is not displayed, then go toStart > All Programs > Accessories

>Windows Explorer.

2.Double-clickthe mapped drive to access it.

Double-ClickMapped Drive

Windows XP

Map a Drive

1.On your desktop, double-clicktheMy Computer icon.

My Computer Icon

NOTE:IftheMyComputericonisnotdisplayed, then go toStart > All Programs > Accessories

>Windows Explorer.

2.In the Address field, enter the server name of the Router:

\\<server_name_of_Router>

Enter Server Name of Router

ThedefaultservernameoftheRouterisWRT160NL.You can change this name on theStorage > Administration screen; refer toStorage > Administration,page 20.

NOTE: Another option is to use the IP address of the Router. In theAddress field, enter the local IP address of the Router:

\\xxx.xxx.xxx.xxx

The default is 192.168.1.1. You can change this IP address on theSetup > Basic Setup screen; refer toSetup > Basic Setup,page 4.

3.A login screen may appear. If prompted, enter your account user name and password. (For the admin account, admin is both the default user name and password.)

Enter Account User Name and Password

User accounts are set up on the Storage>Administration screen; for more information, refer toCreate a User Account,page 38.

Wireless-NBroadband Router with Storage Link

35

Appendix B

How to Install and Access USB Storage

4.Right-clickthe folder you want to share, and clickMap Network Drive. (The default shared folder is named

Public.)

Map Network Drive

5.From the Drive drop-downmenu, select an available drive letter.

Select Drive Letter

6. Click Finish.

Access Mapped Drive

1.On your desktop, double-clicktheMy Computer icon.

My Computer Icon

NOTE:IftheMyComputericonisnotdisplayed, then go toStart > All Programs > Accessories > Windows Explorer.

2.In the Network Drives section,double-clickthe mapped drive to access it.

Double-ClickMapped Drive

Advanced Configuration (Advanced

Users Only)

To manage access to the USB storage device, you can create shared folders, user groups, and user accounts.

Access the Web-BasedUtility

To access the web-basedutility, launch the web browser on your computer, and enter the Router’s default IP address,192.168.1.1, in theAddress field. Then pressEnter.

A login screen will appear. (Non-WindowsXP users will see a similar screen.) Leave theUser name field blank. The first time you open theWeb-basedutility, use the default passwordadmin. (You can set a new password from theAdministration > Management screen.) ClickOK to continue.

Login Screen

Wireless-NBroadband Router with Storage Link

36

Appendix B

How to Install and Access USB Storage

Create a Shared Folder

1.Click the Storage tab.

2.Click the Disk tab.

Storage > Disk

3. To create a shared folder, click Create Share.

Shared Folder

4.In the Display Name field, create a name for the shared folder.

5.If the shared folder should include the entire partition, select Share entire Partition and proceed to step 7.

If you do not want to share the entire partition, then specify the folder you do want to share.

Wireless-NBroadband Router with Storage Link

6.Select the appropriate folder. To display sub-folders,clickEnter into Folder. To return to the previous folder, clickReturn to Upper Folder.

7.To allow a group access to the shared folder, select it from the Available Groups column, and then click the >> button.

NOTE: Specify which user groups have read-and-writeorread-onlyaccess to the shared folders.

8.To block a group from accessing the shared folder, select it from the Groups with Access column, and then click the << button.

9.Click Save Settings to apply your changes, or clickCancel Changes to clear your changes. ClickClose to exit the screen and return to theDisk screen.

Create a User Group Account

1.Click the Storage tab.

2.Click the Administrationtab.

Storage > Administration

3.In the Group Management section, clickCreate New Group.

Group Account

37

Appendix B

How to Install and Access USB Storage

4.In the Group Name field, create a name for the group.

5.In the Description field, enter keywords to describe the group.

6.From the Access drop-downmenu, select the appropriate level of access,read and write orread only.

7.Click Create to apply your changes, or clickCancel to clear your changes. ClickClose to exit the screen and return to theAdministration screen.

Create a User Account

1.Click the Storage tab.

2.Click the Administrationtab.

Storage > Administration

3.In the User Management section, clickCreate New User.

User Account

4.In the Name field, create a name for the user.

5.In the Full Name field, enter the actual name of the user.

6.In the Description field, enter keywords to describe the user.

7.In the Passwordand Confirm Passwordfields, enter the password that the user will use for login.

8.From the Group Member drop-downmenu, select the appropriate user group.

NOTE: To temporarily disable an account, selectAccount Disabled.

9.Click Create User to apply your changes, or clickCancel to clear your changes. ClickClose to exit the screen and return to theAdministration screen.

Wireless-NBroadband Router with Storage Link

38

Appendix C

Specifications

Appendix C:

Specifications

Model

WRT160NL

Standards

802.3, 802.3u, 802.11b, 802.11g,

 

Draft 802.11n

Ports

Internet, Ethernet [1-4],USB, Power

Buttons

Wi-FiProtected Setup, Reset

LEDs

LAN [1-4],Wi-FiProtected Setup™,

 

Wireless, Internet, Power

Cabling Type

CAT 5e

# of Antennas

2

Connector Type

R-SMA

Detachable (y/n)

Yes

RF Pwr (EIRP) in dBm Draft 11n: Typ. 13.5 +/-1.5dBm @ Normal Temp Range

802.11g: Typ. 13.5 +/- 1.5 dBm @ Normal Temp Range

802.11b: Typ: 16 +/- 1.5 dBm @ Normal Temp Range

Receive Sensitivity

802.11n HT40/MCS15

 

270 Mbps: -67dBm 10% PER

 

802.11n HT40/MCS0

 

13.5 Mbps: -75dBm 10% PER

 

802.11n HT20/MCS15

 

130 Mbps: -69dBm 10% PER

 

802.11n HT20/MCS0

 

6.5 Mbps: -79dBm 10% PER

 

802.11g 54 Mbps: -74dBm 10% PER

 

802.11g 6 Mbps: -84dBm 10% PER

 

802.11b 11 Mbps: -86dBm 10% PER

 

802.11b 1 Mbps: -92dBm 10% PER

Antenna Gain in dBi

802.11g: 2.4 GHz <= 1.8dBi

 

Draft 11n: 2.4 GHz <= 1.8 dBi

UPnP able/cert

Able

.Net support

No

Security Features

WEP, WPA, WPA2, RADIUS,

 

SPI Firewall

Security Key Bits

Up to 128-BitEncryption

Supported File

 

Systems for

 

Storage Device

FAT16, FAT32, NTFS

Environmental

Dimensions

7.98" x 6.27" x 1.30"

 

(202.79 x 159.2 x 33.14 mm)

Unit Weight

9.98 oz (283 g)

Power

12V / 1.5A (switching)

Certifications

FCC, UL, cUL, IC, RSS210, CE

Operating Temp.

0 to 40°C (32 to 104°F)

Storage Temp.

-20to 60°C(-4to 140°F)

Operating Humidity

10 to 80%, Relative Humidity,

 

Noncondensing

Storage Humidity

5 to 90% Noncondensing

Specifications are subject to change without notice.

Wireless-NBroadband Router with Storage Link

39

Appendix D

Warranty Information

Appendix D:

Warranty Information

Limited Warranty

Linksys warrants this Linksys hardware product against defects in materials and workmanship under normal use for the Warranty Period, which begins on the date of purchase by the original end-userpurchaser and lasts for the period specified below:

•• One (1) year for new product

•• Ninety (90) days for refurbished product

Your exclusive remedy and Linksys’ entire liability under this limited warranty will be for Linksys, at its option, to

(a)repair the product with new or refurbished parts,

(b)replace the product with a reasonably available equivalentneworrefurbishedLinksysproduct,or(c)refund the purchase price of the product less any rebates. Any repaired or replacement products will be warranted for the remainder of the original Warranty Period or thirty (30) days, whichever is longer. All products and parts that are replaced become the property of Linksys.

Linksys additionally warrants that any media on which the software may be provided will be free from defects in materials and workmanship under normal use for a period of ninety (90) days from the date of original purchase. Your exclusive remedy and Linksys’ entire liability under this limited warranty will be for Linksys, at its option, to

(a) replace the software media, or (b) refund the purchase price of the software media.

Exclusions and Limitations

This limited warranty does not apply if: (a) the product assembly seal has been removed or damaged, (b) the product has been altered or modified, except by Linksys,

(c) the product damage was caused by use with nonLinksys products, (d) the product has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, (e) the product has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident, (f) the serial number on the Product has been altered, defaced, or removed, or

(g) the product is supplied or licensed for beta, evaluation, testing or demonstration purposes for which Linksys does not charge a purchase price or license fee.

EXCEPTFORTHELIMITEDWARRANTYONMEDIASETFORTH ABOVE AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ALL SOFTWARE PROVIDED BY LINKSYS WITH THE PRODUCT, WHETHER FACTORY LOADED ON THE PRODUCT OR CONTAINED ON MEDIA ACCOMPANYING THE PRODUCT, IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND. Without limiting the foregoing, Linksys does

not warrant that the operation of the product or software will be uninterrupted or error free. Also, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the product, software or any equipment, system or network on which the product or software is used will be free of vulnerability to intrusion or attack. The product may include or be bundled with third party software or service offerings. This limited warranty shall not apply to such third party software or service offerings. This limited warranty does not guarantee any continued availability of a third party’s service for which this product’s use or operation may require.

TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary by jurisdiction.

TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT, SOFTWARE OR ANY SERVICES PROVIDED IN RESPECT OF SUCH PRODUCT OR SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this limited warranty fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Obtaining Warranty Service

If

you have

a

question

about

your

product

or

experience

a

problem

with it,

please

go to

www.linksysbycisco.com/support where you will find a variety of online support tools and information to assist you with your product. If the product proves defective during the Warranty Period, contact Linksys Technical Support for instructions on how to obtain warranty service. The telephone number for Linksys Technical Support in your area can be found in the product User Guide and at www.linksysbycisco.com. Have your product serial number and proof of purchase on hand when calling. A

Wireless-NBroadband Router with Storage Link

40

Appendix D

Warranty Information

DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED TO PROCESS WARRANTY CLAIMS. If you are requested to return your product, you will be given a Return Materials Authorization (RMA) number. You are responsible for properly packaging and shipping your product to Linksys at your cost and risk. You must include the RMA number and a copy of your dated proof of original purchase when returning your product. Products received without a RMA number and dated proof of original purchase will be rejected. Do not include any other items with the product you are returning to Linksys. Defective product covered by this limited warranty will be repaired or replaced and returned to you without charge. Customers outside of the United States of America and Canada are responsible for all shipping and handling charges, custom duties, VAT and other associated taxes and charges. Repairs or replacements not covered under this limited warranty will be subject to charge at Linksys’ then-currentrates.

Technical Support

This limited warranty is neither a service nor a support contract. Information about Linksys’ current technical support offerings and policies (including any fees for support services) can be found at www.linksysbycisco.com/support.

This limited warranty is governed by the laws of the jurisdiction in which the Product was purchased by you.

Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.

Wireless-NBroadband Router with Storage Link

41

Appendix E

Regulatory Information

Appendix E:

Regulatory Information

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•• Reorient or relocate the receiving antenna

•• Increase the separation between the equipment or devices

•• Connect the equipment to an outlet other than the receiver’s

•• Consult a dealer or an experienced radio/TV technician for assistance

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

This transmitter must not be co-locatedor operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the USA isfirmware-limitedto channels 1 through 11.

Safety Notices

WARNING: Do not use this product near water, for example, in a wet basement or near a swimming pool.

WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

WARNING: This product contains lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003and RSS210.

Operation is subject to the following two conditions:

1.This device may not cause interference and

2.This device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 2 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

Industry Canada Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

This transmitter must not be co-locatedor operating in conjunction with any other antenna or transmitter.

Wireless-NBroadband Router with Storage Link

42

Appendix E

Regulatory Information

Avis d’Industrie Canada

Cet appareil numérique de la classe B est conforme aux normes NMB-003et RSS210 du Canada.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes :

1.il ne doit pas produire de brouillage et

2.il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Le dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximum de 2 dBi. Les règlements d’Industrie Canada interdisent strictement l’utilisation d’antennes dont le gain est supérieur à cette limite. L’impédance requise de l’antenne est de 50 ohms.

Avis d’Industrie Canada concernant l’exposition aux radiofréquences :

Ce matériel est conforme aux limites établies par IC en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Ce matériel doit être installé et utilisé à une distance d’au moins 20 cm entre l’antenne et le corps de l’utilisateur.

L’émetteur ne doit pas être placé près d’une autre antenne ou d’un autre émetteur, ou fonctionner avec une autre antenne ou un autre émetteur.

Wireless Disclaimer

The maximum performance for wireless is derived from IEEE Standard 802.11 specifications. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions.

Avis de non-responsabilitéconcernant les appareils sans fil

Les performances maximales pour les réseaux sans fil sont tirées des spécifications de la norme IEEE 802.11. Les performances réelles peuvent varier, notamment en fonction de la capacité du réseau sans fil, du débit de la transmission de données, de la portée et de la couverture. Les performances dépendent de facteurs, conditions et variables multiples, en particulier de la distance par rapport au point d’accès, du volume du trafic réseau, des matériaux utilisés dans le bâtiment et du type de construction, du système d’exploitation et de la combinaison de produits sans fil utilisés, des interférences et de toute autre condition défavorable.

Wireless-NBroadband Router with Storage Link

43

Appendix E

Regulatory Information

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE)

This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:

English - Environmental Information for Customers in the European Union

European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.

Български (Bulgarian) - Информация относно опазването на околната среда за потребители в Европейския съюз

Европейска директива 2002/96/EC изисква уредите, носещи този символ върху изделието и/или опаковката му, да не се изхвърля т с несортирани битови отпадъци. Символът обозначава, че изделието трябва да се изхвърля отделно от сметосъбирането на обикновените битови отпадъци. Ваша е отговорността този и другите електрически и електронни уреди да се изхвърлят в предварително определени от държавните или общински органи специализирани пунктове за събиране. Правилното изхвърляне и рециклиране ще спомогнат да се предотвратят евентуални вредни за околната среда и здравето на населението последствия. Запо-подробнаинформация относно изхвърлянето на вашите стари уреди се обърнете към местните власти, службите за сметосъбиране или магазина, от който сте закупили уреда.

Čeština (Czech) - Informace o ochraně životního prostředí pro zákazníky v zemích Evropské unie

Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené tímto symbolem na produktu anebo na obalu bylo likvidováno s netříděným komunálním odpadem. Tento symbol udává, že daný produkt musí být likvidován odděleně od běžného komunálního odpadu. Odpovídáte za likvidaci tohoto produktu a dalších elektrických a elektronických zařízení prostřednictvím určených sběrných míst stanovených vládou nebo místními úřady. Správná likvidace a recyklace pomáhá předcházet potenciálním negativním dopadům na životní prostředí a lidské zdraví. Podrobnější informace o likvidaci starého vybavení si laskavě vyžádejte od místních úřadů, podniku zabývajícího se likvidací komunálních odpadů nebo obchodu, kde jste produkt zakoupili.

Dansk (Danish) - Miljøinformation for kunder i EU

EU-direktiv2002/96/EF kræver, at udstyr der bærer dette symbolpå produktet og/eller emballagen ikke må bortskaffes som usorteret kommunalt affald. Symbolet betyder, at dette produkt skal bortskaffes adskilt fra det almindelige husholdningsaffald. Det er dit ansvar at bortskaffe dette og andet elektrisk og elektronisk udstyr via bestemte indsamlingssteder udpeget af staten eller de lokale myndigheder. Korrekt bortskaffelse og genvinding vil hjælpe med til at undgå mulige skader for miljøet og menneskers sundhed. Kontakt venligst de lokale myndigheder, renovationstjenesten eller den butik, hvor du har købt produktet, angående mere detaljeret information om

bortskaffelse af dit gamle udstyr.

Deutsch (German) - Umweltinformation für Kunden innerhalb der Europäischen Union

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist , nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.

Wireless-NBroadband Router with Storage Link

44

Appendix E

Regulatory Information

Eesti (Estonian) - Keskkonnaalane informatsioon Euroopa Liidus asuvatele klientidele

Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on seadmeid, millel on tootel või pakendil käesolev sümbol , keelatud kõrvaldada koos sorteerimata olmejäätmetega. See sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva ja ka muud elektrija elektroonikaseadmed riigi või kohalike ametiasutuste poolt ette nähtud kogumispunktide kaudu. Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida võimalikke negatiivseid tagajärgi keskkonnale ning inimeste tervisele. Vanade seadmete kõrvaldamise kohta täpsema informatsiooni saamiseks võtke palun ühendust kohalike ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te toote ostsite.

Español (Spanish) - Información medioambiental para clientes de la Unión Europea

La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto.

Ελληνικά (Greek) - Στοιχεία περιβαλλοντικής προστασίας για πελάτες εντός της Ευρωπαϊκής Ένωσης

Σύμφωνα με την Κοινοτική Οδηγία 2002/96/EC, ο εξοπλισμός που φέρει αυτό το σύμβολο στο προϊόν ή/και τη συσκευασία του δεν πρέπει να απορρίπτεται μαζί με τα μη διαχωρισμένα αστικά απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων, οι οποίες ορίζονται από το κράτος ή τις αρμόδιες τοπικές αρχές. Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη ενδεχόμενων αρνητικών επιπτώσεων στο περιβάλλον και την υγεία. Για περισσότερες πληροφορίες σχετικά με την απόρριψη του παλαιού σας εξοπλισμού, επικοινωνήστε με τις τοπικές αρχές, τις υπηρεσίες αποκομιδής απορριμμάτων ή το κατάστημα από το οποίο αγοράσατε το προϊόν.

Français (French) - Informations environnementales pour les clients de l’Union européenne

La directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.

Italiano (Italian) - Informazioni relative all’ambiente per i clienti residenti nell’Unione Europea

La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.

Latviešu valoda (Latvian) - Ekoloģiska informācija klientiem Eiropas Savienības jurisdikcijā

Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst izmest nešķirotā veidā kopā ar komunālajiem atkritumiem (tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo un citas elektriskas un elektroniskas ierīces izmest atkritumos, izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos un pārstrāde tiek veikta pareizi, tad mazinās iespējamais kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā, kur iegādājāties šo izstrādājumu.

Wireless-NBroadband Router with Storage Link

45

Appendix E

Regulatory Information

Lietuvškai (Lithuanian) - Aplinkosaugos informacija, skirta Europos Sąjungos vartotojams

Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį), negalima šalinti kartu su nerūšiuotomis komunalinėmis atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad ši ir kita elektros ar elektroninė įranga būtų šalinama per tam tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose įsigijote tą gaminį.

Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti fl-UnjoniEwropea

Id-DirettivaEwropea 2002/96/KE titlob lit-tagħmirli jkun fih issimbolufuqil-prodottu/jew fuql-ippakkjarma jistax jintrema ma’ skart muniċipali li ma ġiex isseparat.Is-simbolujindika li danil-prodottgħandu jintrema separatament minn ma’ l- iskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi danit-tagħmiru kull tagħmir ieħor ta’l-elettrikuu elettroniku permezz ta’ faċilitajiet ta’ ġbir appuntati appostamill-gvernjewmill-awtoritajietlokali.Ir-rimib’mod korrett ur-riċiklaġġjgħin jipprevjeni konsegwenzi negattivi potenzjaligħall-ambjentugħas-saħħatal-bniedem.Għal aktar informazzjoni dettaljata dwarir-rimitat-tagħmirantik tiegħek, jekk jogħġbok ikkuntattjalill-awtoritajietlokali tiegħek,is-servizzigħar-rimita’l-iskart,jewil-ħanutminn fejn xtrajtil-prodott.

Magyar (Hungarian) - Környezetvédelmi információ az európai uniós vásárlók számára

A 2002/96/EC számú európai uniós irányelv megkívánja, hogy azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott termék kidobásakor a szokványos háztartási hulladékelszállítási rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön felelõssége, hogy ezt, és más elektromos és elektronikus berendezéseit a kormányzati vagy a helyi hatóságok által kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ hulladékfeldolgozás segít a környezetre és az emberi egészségre potenciálisan ártalmas negatív hatások megelõzésében. Ha elavult berendezéseinek felszámolásához további részletes információra van szüksége, kérjük, lépjen kapcsolatba a helyi hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal üzlettel, ahol a terméket vásárolta.

Nederlands (Dutch) - Milieu-informatievoor klanten in de Europese Unie

De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die is voorzien van dit symbool op het product of de verpakking, niet mag worden ingezameld metniet-gescheidenhuishoudelijk afval. Dit symbool geeft aan dat het product apart moet worden ingezameld. U bent zelf verantwoordelijk voor de vernietiging vandezeenandereelektrischeenelektronischeapparatuurviade daarvoor door de landelijke of plaatselijke overheid aangewezen inzamelingskanalen. De juiste vernietiging en recycling van deze apparatuur voorkomt mogelijke negatieve gevolgen voor het milieu en de gezondheid. Voor meer informatie over het vernietigen van uw oude apparatuur neemt u contact op met de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product hebt aangeschaft.

Norsk (Norwegian) - Miljøinformasjon for kunder i EU

EU-direktiv2002/96/EF krever at utstyr med følgende symbolavbildet på produktet og/eller pakningen, ikke må kastes sammen med usortert avfall. Symbolet indikerer at dette produktet skal håndteres atskilt fra ordinær avfallsinnsamling for husholdningsavfall. Det er ditt ansvar å kvitte deg med dette produktet og annet elektrisk og elektronisk avfall via egne innsamlingsordninger slik myndighetene eller kommunene bestemmer. Korrekt avfallshåndtering og gjenvinning vil være med på å forhindre mulige negative konsekvenser for miljø og helse. For nærmere informasjon om håndtering av det kasserte utstyret ditt, kan du ta kontakt med kommunen, en innsamlingsstasjon for avfall eller butikken der du kjøpte

produktet.

Polski (Polish) - Informacja dla klientów w Unii Europejskiej o przepisach dotyczących ochrony środowiska

Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt oznaczony symbolem znajdującym się na produkcie i/lub jego opakowaniu nie był wyrzucany razem z innymi niesortowanymi odpadami komunalnymi. Symbol ten wskazuje, że produkt nie powinien być usuwany razem ze zwykłymi odpadami z gospodarstw domowych. Na Państwu spoczywa obowiązek wyrzucania tego i innych urządzeń elektrycznych oraz elektronicznychwpunktachodbioruwyznaczonychprzezwładze krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób i jego recykling pomogą zapobiec potencjalnie negatywnym konsekwencjom dla środowiska i zdrowia ludzkiego. W celu uzyskania szczegółowych informacji o usuwaniu starego sprzętu, prosimy zwrócić się do lokalnych władz, służb oczyszczania miasta lub sklepu, w którym produkt został nabyty.

Wireless-NBroadband Router with Storage Link

46

Appendix E

Regulatory Information

Português (Portuguese) - Informação ambiental para clientes da União Europeia

A Directiva Europeia 2002/96/CE exige que o equipamento que exibe este símbolo no produto e/ou na sua embalagem não seja eliminado junto com os resíduos municipais não separados. O símbolo indica que este produto deve ser eliminado separadamente dos resíduos domésticos regulares. É da sua responsabilidade eliminar este e qualquer outro equipamento eléctrico e electrónico através das instalações de recolha designadas pelas autoridades governamentais ou locais. A eliminação e reciclagem correctas ajudarão a prevenir as consequências negativas para o ambiente e para a saúde humana. Para obter informações mais detalhadas sobre a forma de eliminar o seu equipamento antigo, contacte as autoridades locais, os serviços de eliminação de resíduos ou o estabelecimento comercial onde adquiriu o produto.

Română (Romanian) - Informaţii de mediu pentru clienţii din Uniunea Europeană

Directiva europeană 2002/96/CE impune ca echipamentele care prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să nu fie casate împreună cu gunoiul menajer municipal. Simbolul indică faptul că acest produs trebuie să fie casat separat de gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi acest produs şi alte echipamente electrice şi electronice prin intermediul unităţilor de colectare special desemnate de guvern sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta la prevenirea potenţialelor consecinţe negative asupra sănătăţii mediului şi a oamenilor. Pentru mai multe informaţii detaliate cu privire la casarea acestui echipament vechi, contactaţi autorităţile locale, serviciul de salubrizare sau magazinul de la care aţi achiziţionat produsul.

Slovenčina (Slovak) - Informácie o ochrane životného prostredia pre zákazníkov v Európskej únii

Podľa európskej smernice 2002/96/ES zariadenie s týmto symbolom na produkte a/alebo jeho balení nesmie byť likvidované spolu s netriedeným komunálnym odpadom. Symbol znamená, že produkt by sa mal likvidovať oddelene od bežného odpadu z domácností. Je vašou povinnosťou likvidovať toto i ostatné elektrické a elektronické zariadenia prostredníctvom špecializovaných zberných zariadení určených vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia pomôže zabrániť prípadným negatívnym dopadom na životné prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie informácie o likvidácii starého zariadenia, obráťte sa, prosím, na miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov alebo obchod, v ktorom ste si produkt zakúpili.

Slovenščina (Slovene) - Okoljske informacije za stranke v Evropski uniji

Evropska direktiva 2002/96/ES prepoveduje odlaganje opreme s tem simbolom – na izdelku in/ali na embalaži z nesortiranimi komunalnimi odpadki. Ta simbol opozarja, da je treba izdelek zavreči ločeno od preostalih gospodinjskih odpadkov. Vaša odgovornost je, da to in preostalo električno in elektronsko opremo oddate na posebna zbirališča, ki jih določijo državne ustanove ali lokalne oblasti. S pravilnim odlaganjem in recikliranjem boste preprečili morebitne škodljive vplive na okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare opreme, se obrnite na lokalne oblasti, odlagališče odpadkov ali trgovino, kjer ste izdelek kupili.

Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille

EU-direktiivi2002/96/EY edellyttää, että jos laitteistossa on tämä symboliitse tuotteessa ja/tai sen pakkauksessa, laitteistoa ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana. Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet viemällä tuote tai tuotteet viranomaisten määräämään keräyspisteeseen. Laitteiston oikea hävittäminen estää mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä myymälästä, josta ostit tuotteen.

Svenska (Swedish) - Miljöinformation för kunder i Europeiska unionen

Det europeiska direktivet 2002/96/EC kräver att utrustning med denna symbol på produkten och/eller förpackningen inte får kastas med osorterat kommunalt avfall. Symbolen visar att denna produktbörkastasefterattdenavskiljtsfrånvanligthushållsavfall. Det faller på ditt ansvar att kasta denna och annan elektrisk och elektronisk utrustning på fastställda insamlingsplatser utsedda av regeringen eller lokala myndigheter. Korrekt kassering och återvinning skyddar mot eventuella negativa konsekvenser för miljön och personhälsa. För mer detaljerad information om kassering av din gamla utrustning kontaktar du dina lokala myndigheter, avfallshanteringen eller butiken där du köpte produkten.

WEB: For additional information, please visitwww.linksysbycisco.com

Wireless-NBroadband Router with Storage Link

47

Appendix F

Software End User License Agreement

Appendix F: Software End

User License Agreement

Cisco Products

This product from Cisco Systems, Inc. or its subsidiary licensing the Software instead of Cisco Systems, Inc. (“Cisco”)containssoftware(includingfirmware)originating from Cisco and its suppliers and may also contain software from the open source community.

Any software originating from Cisco and its suppliers is licensed under the Cisco Software License Agreement contained at Schedule 1 below. You may also be prompted toreviewandaccepttheCiscoSoftwareLicenseAgreement upon installation of the software. Separate terms and features of Network Magic, a Cisco Software product, are set forth in Schedule 2 below.

Any software from the open source community is licensed under the specific license terms applicable to that software made available by Cisco at www.linksysbycisco.com/gpl orasprovidedforinSchedule3below.ByusingtheSoftware, you acknowledge that you have reviewed such license terms and that you agree to be bound by the terms of such licenses. Where such specific license terms entitle you to the source code of such software, that source code is available upon request at cost from Cisco for at least three years from the purchase date of this product and may also be available for download fromwww.linksysbycisco.com/gpl. For detailed license terms and additional information on open source software in Cisco products please look at the Cisco public web site at:www.linksysbycisco.com/gpl/ or Schedule 3 below as applicable. If you would like a copy of the GPL or certain other open source code in this Software on a CD, Cisco will mail to you a CD with such code for $9.99 plus the cost of shipping, upon request.

THIS SOFTWARE END USER LICENSE AGREEMENT IS A LEGAL AGREEMENT BETWEEN YOU AND CISCO. READ IT CAREFULLY BEFORE INSTALLING AND USING THE SOFTWARE. IT PROVIDES A LICENSE TO USE THE SOFTWARE AND CONTAINS WARRANTY INFORMATION AND LIABILITY DISCLAIMERS. BY CHECKING THE “I ACCEPT”BOX, DOWNLOADING, INSTALLING OR USINGTHE SOFTWARE, OR USING THE PRODUCT CONTAINING THE SOFTWARE, YOU ARE CONFIRMING YOUR ACCEPTANCE OF THE SOFTWARE AND CONSENTING TO BE BOUND BY THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL OF THESE TERMS, THEN DO NOT CLICK ON THE “I ACCEPT” BUTTON AND DO NOT DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO

THE RETURN PROCESS AND POLICIES OF THE PARTY FROM WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.

IN THE EVENT THAT YOU HAVE ELECTED TO OBTAIN A SUBSCRIPTION LICENSE, AS INDICATED IN YOUR ORDER, YOU ADDITIONALLY AGREE TO BE BOUND BY THE “TERMS OF SERVICE” SET FORTH IN SCHEDULE 2 IF APPLICABLE.

Software Licenses

The software licenses applicable to software from Cisco are made available at the Cisco public web site at: www.linksysbycisco.com andwww.linksysbycisco.com/gpl/ respectively. For your convenience of reference, a copy of the Cisco Software License Agreement and the main open source code licenses used by Cisco in its products are contained in the Schedules below.

Schedule 1

Cisco Software License Agreement

License. Subject to the terms and conditions of this Agreement, Cisco grants the original end user purchaser of the Software a nonexclusive license to (i) use the Software solely as embedded in, as astand-aloneapplication or (where authorized in the applicable documentation) for communication with such product, each solely at Cisco’s discretion; (ii) if the Software is purchased separately from any Cisco Product, install the Software on personal computers within a single household or business location according to the maximum number of licenses you have purchased; and (iii) make one copy of the Software inmachine-readableform and one copy of the Documentation, solely for backup purposes. This license may not be sublicensed, and is not transferable except to a person or entity to which you transfer ownership of the complete Cisco product containing the Software or complete Software product, provided you permanently transfer all rights under this Agreement and do not retain any full or partial copies of the Software, and the recipient agrees to the terms of this Agreement.

“Software” includes, and this Agreement will apply to

(a) the software of Cisco or its suppliers purchased separately or provided in or with the applicable Cisco product, and (b) any upgrades, updates, bug fixes or modified versions (“Upgrades”) or backup copies of the Software supplied to you by Cisco or an authorized reseller (whether or not for a fee), provided you already hold a valid license to the original software and have paid any applicable fee for the Upgrade.

“Documentation” means all documentation and other related materials supplied by Cisco to you pursuant to this Agreement.

License Restrictions. Other than as set forth in this Agreement, you may not (i) make or distribute copies

Wireless-NBroadband Router with Storage Link

48

Appendix F

Software End User License Agreement

of the Software or its related Documentation, or electronically transfer the Software or Documentation from one computer to another or over a network; (ii) alter, merge, modify, adapt, decrypt or translate the Software or related Documentation, or decompile, reverse engineer, disassemble, or otherwise reduce the Software to a human-perceivableform (except to the extent expressly permitted by law notwithstanding this provision); (iii) share, sell, rent, lease, or sublicense the Software or related Documentation; (iv) modify the Software or create derivative works based upon the Software; (v) if you make a backup copy of the Software and Documentation, you must reproduce all copyright notices and any other proprietary legends found on the original Software and Documentation; (vi) use the Software for management of a business network with more than 8 computers; (vii) use the Software under any circumstances for competitive evaluation, including developing competing software; (ix) to the extent permitted under applicable law, assign, sublicense or otherwise transfer the Software unless the prospective assignee, sublicensee or transferee expressly agrees to all the terms and conditions under this Agreement.

The Software and Documentation contain trade secrets and/or copyrighted materials of Cisco or its suppliers. You will not disclose or make available such trade secrets or copyrighted material in any form to any third party.

In the event that you fail to comply with this Agreement, the license granted to you will automatically terminate, at which time you must immediately (i) stop using the Cisco Product in which the Software is embedded, or (ii) uninstall the Software and destroy all copies of the Software and Documentation where the Software is purchased separately. All other rights of both parties and all other provisions of this Agreement will survive this termination.

Ownership. The Software and Documentation are licensed and not sold to you by Cisco and the relevant third parties set forth in Schedule 3. Cisco and its licensors retain all right, title and interest, including all copyright and intellectual property rights, in and to, the Software and Documentation and all copies and portions thereof. All rights not specifically granted to you in this Agreement are reserved by Cisco and its licensors. Your use of any software product from an entity other than Cisco that may have been recommended by Cisco is governed by such software product’s end user license agreement.

Links and Advertising. Cisco may provide from within the Software links to websites or third party software products that are beyond our control. Cisco makes no representations as to the quality, suitability, functionality, or legality of any sites or products to which links may be provided, and you hereby waive any claim you might have against Cisco with respect to such sites or third party software products. Your correspondence or

business dealings with, or participation in promotions of advertisers found through the Software and any other terms, conditions, warranties, or representations associated with such dealings, are solely between you and such advertiser. You agree that Cisco is not responsible or liable for any loss or damage of any sort incurred as the result of any such dealings or as the result of the presence of such advertisers in the Cisco Software.

Collection and Processing of Information. You agree that Cisco and/or its affiliates may, from time to time, collect and process information about your Cisco product and/or the Software and/or your use of either in order

(i) to enable Cisco to offer you Upgrades; (ii) to provide support and assistance with your product and/or the Software; (iii) to ensure that your Cisco product and/or the Software is being used in accordance with the terms of this Agreement; (iv) to provide improvements to the way Cisco delivers technology to you and to other Cisco customers; (v) to provide reports regarding the status and health of the network, including network traffic and application usage; (vi) to enable Cisco to comply with the terms of any agreements it has with any third parties regarding your Cisco product and/or Software; and/or (vii) to enable Cisco to comply with all applicable laws and/or regulations, or the requirements of any regulatory authority or government agency. Cisco and/ or its affiliates may collect and process this information provided that it does not identify you personally.

The reports feature of certain Software allows you to monitor the activity of computers running the Software in your home or small office. You must activate this feature in order to receive reports. If you activate the reports feature, you agree to the following: (a) the Software tracks and monitors the following components and activities in your home or office: network traffic (e.g. megabytes per hour), application usage (the foreground window is tracked and the time each application is in the foreground during active usage of the computer) and internet history. (b) For all computers on which reports feature is enabled, the above information is transmitted to servers at Cisco and/ or a third party at periodic intervals while the computer is online. This information is associated and stored with the email address supplied by you when you activated the reports feature. This information is summarized into a formal report and is emailed to the identified email address. (c) Any computer on the network running the Software can enable any other computer (on the same primary network) to generate reports. When a computer is enabled, that computer shows a notification that it is being monitored. As long as that computer is enabled, each time the Software is started the user of that particular computer will see a notification that it is being monitored by the reports feature. Any computer on the network with the Software installed can enable or disable any other computer from the reports feature.

Wireless-NBroadband Router with Storage Link

49

Appendix F

Software End User License Agreement

In addition, Cisco may collect and store detailed information regarding your network configuration and usage for the purpose of providing you technical networking support. The information is associated with you only when you provide a unique ID number to the support representative while you are receiving help. The unique ID is generated randomly on your computer upon installation and is completely under your control.

Your use of your Cisco product and/or the Software constitutes consent by you to Cisco’s and/or its affiliates’ collection and use of such information and, for European Economic Area (EEA) customers, to the transfer of such information to a location outside the EEA. Any information collected by your Cisco product and/or the Software is done and utilized in accordance with our Privacy Policy available at Privacy Statement. Your election to use the Cisco product and/or Software indicates your acceptance of the terms of the Cisco Privacy Policy, so please review the policy carefully and check the Web site above to review updates to it.

Software Upgrades etc. If the Software enables you to receive Upgrades, you may elect at any time to receive these Upgrades either automatically or manually. If you elect to receive Upgrades manually or you otherwise elect not to receive or be notified of any Upgrades, you may expose your Cisco product and/or the Software to serious security threats and/or some features within your Cisco product and/or Software may become inaccessible. There may be circumstances where we apply an Upgrade automatically in order to comply with changes in legislation, legal, security or regulatory requirements or as a result of requirements to comply with the terms of any agreements Cisco has with any third parties regarding your Cisco product and/or the Software. You will always be notified of any Upgrades being delivered to you. The terms of this license will apply to any such Upgrade unless the Upgrade in question is accompanied by a separate license, in which event the terms of that license will apply.

Term and Termination. You may terminate this License at any time by destroying all copies of the Software and documentation. Your rights under this License will terminate immediately without notice from Cisco if you fail to comply with any provision of this Agreement.

Limited Warranty. Cisco additionally warrants that any media on which the Software may be provided will be free from defects in materials and workmanship under normal use for a period of ninety (90) days from the date of original purchase. Your exclusive remedy and Cisco’s entire liability under this limited warranty will be for Cisco, at its option, to (a) replace the Software media, or (b) refund the purchase price of the Software media.

EXCEPT FOR THE LIMITED WARRANTY ON MEDIA SET FORTH ABOVE ANDTOTHE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ALL SOFTWARE PROVIDED BY CISCO

IS PROVIDED “AS IS” WITH ALL FAULTS AND WITHOUT WARRANTY OF ANY KIND. Without limiting the foregoing, Cisco does not warrant that the operation of the product or software will be uninterrupted or error free. Also, due to the continual development of new techniques for intruding upon and attacking networks, Cisco does not warrant that the product, software or any equipment, system or network on which the product or software is used will be free of vulnerability to intrusion or attack. The product may include or be bundled with third party software or service offerings. This limited warranty shall not apply to such third party software or service offerings. This limited warranty does not guarantee any continued availability of a third party’s service for which this product’s use or operation may require.

TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary by jurisdiction.

Disclaimer of Liabilities. TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT WILL CISCO BE LIABLE FORANYLOSTDATA,REVENUEORPROFIT,ORFORSPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT, SOFTWARE OR ANY SERVICES PROVIDED IN RESPECT OF SUCH PRODUCT OR SOFTWARE, EVEN IF CISCO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT WILL CISCO’S LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this limited warranty fails of its essential purpose.

Technical Support. This limited warranty is neither a service nor a support contract. Information about Cisco’s current technical support offerings and policies (including any fees for support services) can be found atwww.linksysbycisco.com/support.

Export. Software, including technical data, may be subject to U.S. export control laws and regulations and/or export or import regulations in other countries. You agree to comply strictly with all such laws and regulations.

U.S.GovernmentUsers.The Software and Documentation qualify as “commercial items” as defined at 48 C.F.R. 2.101 and 48 C.F.R. 12.212. All Government users acquire the Software and Documentation with only those rights herein that apply tonon-governmentalcustomers. Use of

Wireless-NBroadband Router with Storage Link

50

Appendix F

Software End User License Agreement

either the Software or Documentation or both constitutes agreement by the Government that the Software and Documentation are “commercial computer software” and “commercial computer software documentation,” and constitutes acceptance of the rights and restrictions herein.

General Terms. This Agreement will be governed by and construed in accordance with the laws of the State of California, without reference to conflict of laws principles. The United Nations Convention on Contracts for the International Sale of Goods will not apply. If any portion of this Agreement is found to be void or unenforceable, the remaining provisions will remain in full force and effect. This Agreement constitutes the entire agreement between the parties with respect to the Software and supersedes any conflicting or additional terms contained in any purchase order or elsewhere.

Linksys, Cisco and the Cisco Logo and other trademarks contained in the Software and Documentation are trademarks or registered trademarks of Linksys, Cisco, its licensors and third parties, as the case may be. You may not remove or alter any trademark, trade names, product names, logo, copyright or other proprietary notices, legends, symbols or labels in the Software and Documentation. This Agreement does not authorize you to use Cisco’s or its licensors’ names or respective trademarks.

END OF SCHEDULE 1

Schedule 2

Network Magic Features

Network Magic License Restrictions. Other than as set forth in this Agreement, you may not install or execute the Network Magic Software on any non-personal computer product, including, but not limited to, a Web appliance, set top box, handheld device, phone, Web pad device, or any device running the Microsoft Windows CE operating system.

Terms of Service for Subscription Licenses. These Terms of Service only apply if you have obtained a subscription license to Network Magic as specified in your order.

1.Network Magic Cancellation. You may cancel the Servicesatanytime.IfyoucanceltheServices,Ciscowillnot be obligated to provide you any Network Magic product Upgrades. To the extent not prohibited by applicable law, you understand and agree that cancellation of your Services is your sole remedy with respect to any dispute with Cisco.

2.Modifications. Cisco may modify or cancel the terms of thisAgreementortheprice,content,ornatureoftheServices (including discontinuing the Services program), upon notice to you. If Cisco modifies any of these terms, you may cancel the Service by providing written notice to Cisco via

www.networkmagic.com/support of such cancellation and uninstalling the Software and discontinuing your use of the Service. Cisco may provide notice by e-mail, via Network Magic, or by publishing the changes on its Web site.

3. Email Notification. Cisco may send you email from time to time to let you know about new products and services that are available to you. You will be able toopt-outof receiving these emails using the link provided within the email.Ciscoreservestheright,however,tosendyouService relatedemailmessagesaslongasyouareasubscribertothe Service. If you wish toopt-outof receiving Service related email messages, you may cancel the Service by providing written notice viawww.networkmagic.com/support to Cisco of such cancellation and uninstalling the Software and discontinuing your use of the Service.

4. WARRANTY DISCLAIMER FOR SERVICES. TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW THE SERVICES ARE PROVIDED ON AN “AS-IS” BASIS, AND CISCO AND ITS SUPPLIERS DISCLAIM ALL WARRANTIES AND REPRESENTATIONS REGARDING THE SERVICES, WHETHER EXPRESS, IMPLIED, OR OTHERWISE, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, TITLE, QUIET ENJOYMENT, QUALITY, AND ACCURACY. CISCO DOES NOT WARRANT THAT THE SERVICE IS ERROR-FREE OR THAT THE SERVICE WILL OPERATE WITHOUT INTERRUPTION

END OF SCHEDULE 2

Schedule 3

Open Source and Third Party Licenses

Schedule 3-A

If this Cisco product contains open source software licensed under Version 2 of the “GNU General Public License”then the license terms below in this Schedule 3-Awill apply to that open source software. The license terms below in this Schedule3-Aare from the public web site athttp://www.gnu.org/copyleft/gpl.html

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

Copyright © 1989, 1991 Free Software Foundation, Inc.

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your

Wireless-NBroadband Router with Storage Link

51

Appendix F

Software End User License Agreement

freedom to share and change free software--tomake sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.

The precise terms and conditions for copying, distribution and modification follow.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0.This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion

of it, either verbatim or with modifications and/ or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

1.You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring

acopy, and you may at your option offer warranty protection in exchange for a fee.

2.You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a.You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.

b.You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.

Wireless-NBroadband Router with Storage Link

52

Appendix F

Software End User License Agreement

c.If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement

including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3.You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:

a.Accompany it with the complete corresponding machine-readablesource code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

b.Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readablecopy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

c.Accompany it with the information you received as totheoffertodistributecorrespondingsourcecode. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

4.You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5.You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6.Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

Wireless-NBroadband Router with Storage Link

53

Appendix F

Software End User License Agreement

7.If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-freeredistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8.If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9.The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does

not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10.If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

11.BECAUSETHE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED INWRITINGTHE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12.INNOEVENTUNLESSREQUIREDBYAPPLICABLELAWOR AGREEDTO INWRITINGWILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

END OF SCHEDULE 3-A

Schedule 3-B

IfthisCiscoproductcontainsopensourcesoftwarelicensed under Version 2.1 of the “GNU Lesser General Public License” then the license terms below in this Schedule 3-Bwill apply to that open source software. The license terms below in this Schedule3-Bare from the public web site athttp://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

Wireless-NBroadband Router with Storage Link

54

Appendix F

Software End User License Agreement

GNU LESSER GENERAL PUBLIC LICENSE

Version 2.1, February 1999

Copyright (C) 1991, 1999 Free Software Foundation, Inc.

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software—tomake sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software packages—typicallylibraries—ofthe Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-stepmethod: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/ or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-freeprograms.

When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.

We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-freeprograms. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-factostandard. To achieve this,non-freeprograms must be allowed to use the library. A more frequent case is that a free library does the same job as widely usednon-freelibraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.

In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-freeprograms enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the

Wireless-NBroadband Router with Storage Link

55

Appendix F

Software End User License Agreement

freedom and the wherewithal to run that program using a modified version of the Library.

The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

GNU LESSER GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0.This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser

General Public License (also called “this License”). Each licensee is addressed as “you”.

A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.

The “Library”, below, refers to any such software library or work which has been distributed under these terms. A“work based on the Library”means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modification”.)

“Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.

1.You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2.You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a)The modified work must itself be a software library.

b)You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.

c)You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.

d)If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely welldefined independent of the application. Therefore,

Subsection 2d requires that any applicationsupplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Wireless-NBroadband Router with Storage Link

56

Appendix F

Software End User License Agreement

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library.

In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3.You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy.

This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4.You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readablesource code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.

If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

5.A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.

However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.

When a “work that uses the Library”uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.

If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

6.As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer’s own use and reverse engineering for debugging such modifications.

You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things:

a)Accompany the work with the complete corresponding machine-readablesource code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the completemachine-readable“work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.)

Wireless-NBroadband Router with Storage Link

57

Appendix F

Software End User License Agreement

b)Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that

(1)uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the executable, and

(2)will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatiblewith the version that the work was made with.

c)Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.

d)If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.

e)Verify that the user has already received a copy of these materials or that you have already sent this user a copy.

For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7.You may place library facilities that are a work based on the Library side-by-sidein a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things:

a)Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above.

b)Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.

8.You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9.You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

10.Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.

11.If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-freeredistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of

Wireless-NBroadband Router with Storage Link

58

Appendix F

Software End User License Agreement

software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

12.If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

13.The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and“any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.

14.If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED INWRITINGTHE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

END OF SCHEDULE 3-B

Schedule 3-C

OPENSSL LICENSE

If this Cisco product contains open source software licensed under the OpenSSL license:

This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/).

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com).

This product includes software written by Tim Hudson (tjh@cryptsoft.com).

In addition, if this Cisco product contains open source software licensed under the OpenSSL license then the license terms below in this Schedule 3-Cwill apply to that open source software. The license terms below in this Schedule3-Care from the public web site athttp://www.openssl.org/source/license.html.

Wireless-NBroadband Router with Storage Link

59

Appendix F

Software End User License Agreement

The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-styleOpen Source licenses. In case of any license issues related to OpenSSL please contactopenssl-core@openssl.org.

OpenSSL License

Copyright © 1998-2007The OpenSSL Project. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1.Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2.Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”

4.The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-core@openssl.org.

5.Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project.

6.Redistributions of any form whatsoever must retain the following acknowledgment:“This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).

Original SSLeay License

Copyright © 1995-1998Eric Young (eay@cryptsoft.com) All rights reserved.

This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).

The implementation was written so as to conform with Netscape’s SSL.

This library is free for commercial and non-commercialuse as long as the following conditions are adhered to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft. com).

Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed.

If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1.Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

2.Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement:

“This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)”

The word ‘cryptographic’ can be left out if the routines from the library being used are not cryptographic related.

4.IfyouincludeanyWindowsspecificcode(oraderivative thereof) from the apps directory (application code) you must include an acknowledgement: “This product includes software written by Tim Hudson (tjh@ cryptsoft.com)”

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,

Wireless-NBroadband Router with Storage Link

60

Appendix F

Software End User License Agreement

BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The license and distribution terms for any publicly available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution license [including the GNU Public License.]

END OF SCHEDULE 3-C

Wireless-NBroadband Router with Storage Link

9021610NC-JL

61