Denon DN-C680 User Manual

5 (1)
Denon DN-C680 User Manual

CD PLAYER

DN-C680

OPERATING INSTRUCTIONS

IMPORTANT TO SAFETY

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

1.Handle the power supply cord carefully

Do not damage or deform the power supply cord. If it is damaged or deformed, it may cause electric shock or malfunction when used. When removing from

wall outlet, be sure to remove by holding the plug attachment and not by pulling the cord.

2.Do not open the top cover

In order to prevent electric shock, do not open the top cover. If problems occur, contact your DENON dealer.

3.Do not place anything inside

Do not place metal objects or spill liquid inside the CD player. Electric shock or malfunction may result.

Please, record and retain the Model name and serial number of your set shown on the rating label.

Model No. C-680

Serial No.

NOTE:

This CD player uses the semiconductor laser. To allow you to enjoy music at a

stable operation, it is recommended to use this in a room of 5°C (41 °F) - 35°C (95°F).

LABELS (for U.S.A. model only)

CERTIFICATION

THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR REFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.

NOTE:

This unit may cause interference to radio and television reception if you do not operate it in strict accordance with this OPERATING INSTRUCTIONS.

This unit complies with Class B computing device rules in accordance with the specifications in Sub-part J or Part 15 of the FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. If the unit does cause interference to any radio or television reception, try to reduce it by one or more of the following means:

a)Turn the other unit to improve reception

b)Move this unit

c)Move this unit away from others

d)Plug this unit respectively into a different AC outlet

This is note to accordance with Section 15.838 of the FCC Rules.

CLASS 1 LASER PRODUCT

2

SAFETY INSTRUCTIONS

1.Read Instructions – All the safety and operating instructions should be read before the applicance is operated.

2.Retain Instructions – The safety and operating instructions should be retained for future reference.

3.Heed Warning – All warnings on the applicance and in the operating instructions should be adhered to.

4.Following Instructions – All opeerating and use instructions should be followed.

5.Water and Moisture – The appliance should not be used near water – for example, near a bathtub, washbbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like.

6.Carts and Stands – The appliance should be used only with a cart or stand that is recommended by the manufacturer.

6A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the applicance and cart

combination to overturn.

7.Wall or Ceiling Mounting – The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

8.Ventilation – The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

9.Heat – The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

10.Power Sources – The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.

11.Grounding or Polarization – Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL

ELECTRICAL CODE ANTENNA

LEAD IN

WIRE

GROUND

CLAMP

ANTENNA DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRIC

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

12.Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

14.Cleaning – The appliance should be cleaned only as recommended by the manufacturer.

15.Power Lines – An outdoor antenna should be located away from power lines.

16.Outdoor Antenna Grounding – If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.

17.Nonuse Periods – The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.

18.Object and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

19.Damage Requiring Service – The appliance should be serviced by qualified service personnel when:

A.The power-supply cord or the plug has been damaged; or

B.Objects have fallen, or liquid has been spilled into the appliance; or

C.The appliance has been exposed to rain; or

D.The appliance does not appear to operate normally or exhibits a marked change in performance; or

E.The appliance has been dropped, or the enclosure damaged.

20.Servicing – The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.

3

FRONT PANEL

REAR PANEL

DIMENSIONS

DISPLAY WINDOW

4

5

NOTE ON USE

Keep the set free from moisture, water, and dust.

Avoid high temperatures

Allow for sufficient heat dispersion when installed on a rack.

Do not let foreign objects in the set.

Handle the power cord carefully. Hold the plug when unplugging the cord.

Unplug the power cord when not using the set for long periods of time.

"(For sets with ventilation holes)

Do not obstruct the ventilation holes.

Do not let insecticides, benzene, and thinner come in contact with the set.

Never disassemble or modify the set in any way.

6

MAIN FEATURES

The DN-C680 CD player is a rack mount type CD player designed for use in broadcast stations, for production; etc.

19 inch Rack Mountable (Height 3U)

Large FL Display, Illuminated Rubber Button

Track Search Select knob (Easy track selection)

Jog/ Shuttle Wheel

Perform searches to 1 frame precision using the jog dial and easy scans using the shuttle ring.

Program Play (Max. 25 tracks)

(1)When the PLAY mode is set to Single, the player stands by at the beginning of next track. (at Finish mode Next)

(2)When the PLAY mode is set to Continuous, the playback is continued according to your programmed sequence.

Play mode and Finish mode

(1)Play mode

cContinuous: Play a whole disc dSingle: Play a track

eA-B: Play a A-B

(2)Finish mode (Stop, Next, Recue)

*only when Single Track play is selected. cStop: Stop after finishing to play a track.

dNext: Standby at the beginning of next track after finishing to play track. eRecue: After finishing to play a track, standby at the beginning of the track.

Auto Cue

After a disc is loaded, it is automatically cued to the point where audio starts. Cueing takes place at the point where audio starts rather than where the track starts. The level at which sound is first detected can be set between -36 to -72dB (7 steps).

End Monitor

Pressing the END MON button during standby instantly previews the end of the track, thus assuring perfect "end point". The point at which monitoring starts can be set within a range of 5 to 35 seconds (7 steps) prior to the track's end.

End of Message (EOM)

At the end of a track, the Display's EOM button flashes, providing a visual warning to the operator that the track will end shortly. The point at which the flashing begins can be set within a range of 0 to 30 seconds (7 steps) prior to the end of the track.

Pitch Control (t 9.9%, 0.1 % step) e Index Search

The Select knob can be used to perform an Index Search when the INDEX button is ON. (The LED on the INDEX button light up.)

AUTO SPACE

During playback, it is possible to insert a silent space of about 4 seconds between tracks. To do this, simply press the AUTO SPACE button to ON. (The LED on the AUTO SPACE button light up.)

AUTO EDIT

This function automatically divides the total recorded time on the disc in half and rearranges the track so that they fit nearly onto the A and B sides.

Display of Playback Locations

A bar graph display indicates playback points on the track being played. Elapsed time and Remaining time displays are switched using the TIME button.

Rich Array of External Control Terminals

Serial Remote (RS232C/RS422A switchable, D-sub 9 pin) Parallel Remote (D-sub 25 pin)

ACD-25FSC (FS Converter Kit) Option

Digital output is possible at 32 and 48 kHz as well as 44.1 kHz. Output frequency can be preset to 32, 44.1, or 48 kHz.

7

CONTENTS

1.

PART NAMES AND FUNCTIONS .................................................

9~11

6.

PROGRAMMED PLAYBACK ........................................................

19~21

 

(1) Front Panel ..........................................................................

9,10

 

(1)

Inputting the Program ............................................................

19

 

(2) Rear Panel .........................................................................

10,11

 

(2)

Changing the Program ........................................................

19, 20

 

(3) Display ...................................................................................

11

 

(3)

Playing Programs ...................................................................

20

2.

REMOTE CONTROL CONNECTION ...................................................

12

 

(4)

Presetting Programs ................................................................

21

3.

OPENING AND CLOSING THE DISC HOLDER AND

 

7.

PRESET FUNCTIONS AND OPERATIONS ..................................

22~25

 

LOADING DISCS ...........................................................................

12

 

(1)

List of Preset Functions ...........................................................

22

4.

BASIC OPERATION .................................................................

13, 14

 

(2) Presetting Procedure ...............................................................

23

 

(1)

Before Starting Playback ...........................................................

13

 

(3) Detailed Description of Preset Functions ..............................

24, 25

 

(2)

Starting Playback .....................................................................

14

8.

BEFORE SWITCHING OFF THE POWER ..........................................

26

 

(3) Stopping Playback ...................................................................

14

9.

COMPACT DISCS .........................................................................

26

 

(4) PLAY/PAUSE and STANDBY/CUE Operations...............................

14

10.

TROUBLESHOOTING .....................................................................

27

5.

HANDY OPERATIONS ...............................................................

15-18

11.

SPECIFICATIONS ..........................................................................

27

 

(1) Starting Playback from the Middle of a Track

 

 

 

 

 

 

 

(Manual Search) .......................................................................

15

 

 

 

 

 

(2)

Playing at a. Different Speed (Pitch) ..........................................

15

 

 

 

 

 

(3)

Playing a Specific Section of the Disc (A-B Play) ..........................

16

 

 

 

 

 

(4)

Playing Repeatedly (Repeat) .....................................................

17

 

 

 

 

 

(5)

Inserting Blank Spaces Between Tracks (Auto Space) ..................

18

 

 

 

 

 

(6)

Dividing the Playing Time in Two (Auto Edit) ..............................

18

 

 

 

 

Checking the Contents

 

 

 

 

 

Check that the carton contains the following items:

 

 

 

 

 

 

3P power supply cord

1 PC.

 

 

 

 

 

Operating instructions (this booklet)

1 PC.

 

 

 

 

Installing the Units

Mount the units onto your console or rack with 19" EIA rack rails.

CAUTION:

The DN-C680 will work normally when the player unit is mounted with the front panel within 15 degrees of the vertical plane. If the unit is tilted excessively, discs may not load or unload properly.

Max. 15°

DN-C580

DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards: EN60065, EN55013, EN55020, EN60555-2 and EN60555-3. Following the provisions of 73/23/EEC, 89/336/EEC and 93/68/EEC Directive.

8

PART NAMES AND FUNCTIONS

(1) Front Panel

POWER button

This turns the set on and off.

Disc holder

Place discs in this holder.

Press the OPEN/CLOSE button to open and close the disc holder. Load discs firmly inside the slot.

OPEN/ CLOSE button

Press this button to open and close the disc holder. The disc holder will not open during playback.

LEVEL control

Use this to adjust the volume of the headphones.

PHONES jack

Connect headphones with an impedance of 30 to 40 62/ohms.

STOP button

Press this button to turn all the servo functions off and stop. Press this button during playback to set the stop mode.

STANBDY / CUE button

When this button is pressed during the play or pause mode, the pickup returns to the position at which playback started and the standby mode is set. (Back Cue)

When pressed during playback when the next track has been programmed, the programmed track is searched for and the standby mode is set.

The button lights when the standby mode is set.

When the button is pressed while pressing the PLAY MODE button, the preset mode is set.

PLAY / PAUSE button

Press this button in the standby, pause or manual search mode to begin playback.

Press the button in the stop mode to search for the first track and begin playback.

The button lights during the play mode.

When the button is pressed during playback, the pause mode is set. The button flashes while the pause mode is set.

PROG. PLAY ON/ OFF button

When this button is pressed while the PROGRAM IN button is lit, the program play mode is set.

The button will not function during the A-B play mode.

The button lights during the program play standby and play modes.

When the button is pressed during the program play standby or play mode, the program play mode is cleared.

PROGRAM IN button

Press this button to set the program input mode.

The button will not function during the play mode.

The button flashes when in the program input mode.

The button lights when a program is set.

Select knob

Turn this' knob to select the next track (or index number) to be played.

Use the INDEX button to choose whether to select tracks or index numbers.

Turn the knob clockwise by one click to move one track (or one index number) forward, counterclockwise by one click to move one track (or one index number) backward.

When the knob turned while pressing it in, one click corresponds to 10 tracks (or 10 index numbers).

In the preset mode, use this knob to set and enter preset settings.

When setting programs, use this knob to select, enter and check the program.

PLAY MODE button

Press this button to switch the play mode.

PITCH button

Press this button to switch to the play speed set with the + and -buttons.

The button lights when the pitch play mode is set.

Press the button again to cancel the pitch play mode and return to the normal speed.

+ button

Press this button once to increase the pitch by 0.1 %.

Hold the button in to increase the pitch continuously.

Press the button in the program editing mode to set the program insert mode.

- button

Press this button once to decrease the pitch by 0.1%.

Hold the button in to decrease the pitch continuously.

Press the button in the program editing mode to clear the program.

END MON button

Press this button in the standby mode to monitor the end of the track. (End Monitor)

The button lights when the end monitor mode is set.

REPEAT button

Press this button to set the repeat mode.

The button lights when the repeat mode is set.

Press the button again to cancel the repeat mode.

A button

Press this button when no A point is set to set the A point.

The button lights when the A point is set.

When pressed while the A point is set, the A point is searched for and the standby mode is set.

When the button is pressed during manual search while the A point is set, the A point changes.

B button

Press this button when no B point is set to set the B point.

The button lights when the B point is set.

When pressed while the B point is set, the B point is searched for and the standby mode is set.

When the button is pressed during manual search while the B point is set, the B point changes.

9

Loading...
+ 18 hidden pages