Denon AVR-1802 882 User Manual

AV SURROUND RECEIVER

AVR-1802/882

OPERATING INSTRUCTIONS

MODE D’EMPLOI

				CD	MD/CDR
				AUDIO	VIDEO
			POWER
		AVR/AVC	TV	VCR	DVD/VDP
		ON
			PHONO	CD	DVD/VDP
		OFF
B PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER AVR-1802		V.AUX VCR-1 VCR-2 TV/DBS
		MASTER VOLUME
		INPUT MODE	CDR / TAPE	TUNER	SHIFT
CD	PHONO

SURROUND REMOTE VOLUME LEVEL MODE SENSOR

SIGNAL

DVD / VDP	TUNER			DIGITAL
						0
						3
				INPUT
VCR-1	TV / DBS	ON / STANDBY	AUTO	PCM	DTS	VIDEO SELECT

TITLE

TAPE·VCR

6 7

CHANNEL

2

0

CD·MD/CDR·DVD/VDP DISC SKIP+

CDR / TAPE

VCR-2

V. AUX

SHIFT

DOWN

UP

BAND

MODE

MEMORY

DOWN

UP

VIDEO SELECT

DIMMER

STATUS

8

3

9

PRESET

TUNING

6

2

7

SYSTEM

SURROUND

SET UP

CH SELECT

MENU

MASTER

ON / STANDBY

PHONES

SPEAKER

INPUT

V.AUX INPUT

SURROUND

SELECT

CH VOL

VOL

OPTICAL VIDEO

L

AUDIO

R

A

B

INPUT MODE

ANALOG

EXT. IN

CINEMA EQ TONE DEFEAT

SELECT

T.TONE

STATUS

MUTING

SURROUND

TONE

PARAMETER

CONTROL

RETURN

DISPLAY

CHANNEL TV VOLUME

B

REMOTE CONTROL UNIT RC-897

FOR ENGLISH READERS		PAGE 2 ~ PAGE 48, 94, 95

2We greatly appreciate your purchase of this unit.

2To be sure you take maximum advantage of all the features this unit has to offer, read these instructions carefully and use the set properly. Be sure to keep this manual for future reference should any questions or problems arise.

“SERIAL NO.

PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE”

POUR LES LECTEURS FRANCAIS PAGE 2, 49 ~ PAGE 95

2Nous vous remercions pour l’achat de cet appareil.

2Pour être sûr de profiter au maximum de toutes les caractéristiques qu’offre cet appareil, lire avec soin ces instructions et bien utiliser l’appareil. Toujours conserver ce mode d’emploi pour s’y référer ultérieurement en cas de question ou de problème.

“NO. DE SERIE

PRIERE DE NOTER LE NUMERO DE SERIE DE L’APPAREIL INSCRIT A L’ARRIERE DU COFFRET DE FAÇON A POUVOIR LE CONSULTER EN CAS DE PROBLEME.”

ENGLISH FRANCAIS

2SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU FOND.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

2NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION

•Avoid high temperatures.

Allow for sufficient heat dispersion when installed on a rack.

•Eviter des températures élevées.

Tenir compte d’une dispersion de chaleur suffisante lors de l’installation sur une étagère.

•Handle the power cord carefully.

Hold the plug when unplugging the cord.

•Manipuler le cordon d’alimentation avec précaution.

Tenir la prise lors du débranchement du cordon.

•Keep the set free from moisture, water, and dust.

•Protéger l’appareil contre l’humidité, l’eau et la poussière.

•Unplug the power cord when not using the set for long periods of time.

•Débrancher le cordon d’alimentation lorsque l’appareil n’est pas utilisé pendant de longues périodes.

*(For sets with ventilation holes)

•Do not obstruct the ventilation holes.

•Ne pas obstruer les trous d’aération.

•Do not let foreign objects in the set.

•Ne pas laisser des objets étrangers dans l’appareil.

•Do not let insecticides, benzene, and thinner come in contact with the set.

•Ne pas mettre en contact des insecticides, du benzène et un diluant avec l’appareil.

•Never disassemble or modify the set in any way.

•Ne jamais démonter ou modifier l’appareil d’une manière ou d’une autre.

2

SAFETY INSTRUCTIONS

1.Read Instructions – All the safety and operating instructions should be read before the appliance is operated.

2.Retain Instructions – The safety and operating instructions should be retained for future reference.

3.Heed Warnings – All warnings on the appliance and in the operating instructions should be adhered to.

4.Follow Instructions – All operating and use instructions should be followed.

5.Water and Moisture – The appliance should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like.

6.Carts and Stands – The appliance should be used only with a cart or stand that is recommended by the manufacturer.

6A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart

combination to overturn.

7.Wall or Ceiling Mounting – The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

8.Ventilation – The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

9.Heat – The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

10.Power Sources – The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.

11.Grounding or Polarization – Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL

ELECTRICAL CODE ANTENNA

LEAD IN

WIRE

GROUND

CLAMP

ANTENNA DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRIC

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

12.Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

14.Cleaning – The appliance should be cleaned only as recommended by the manufacturer.

15.Power Lines – An outdoor antenna should be located away from power lines.

16.Outdoor Antenna Grounding – If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.

17.Nonuse Periods – The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.

18.Object and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

19.Damage Requiring Service – The appliance should be serviced by qualified service personnel when:

A.The power-supply cord or the plug has been damaged; or

B.Objects have fallen, or liquid has been spilled into the appliance; or

C.The appliance has been exposed to rain; or

D.The appliance does not appear to operate normally or exhibits a marked change in performance; or

E.The appliance has been dropped, or the enclosure damaged.

20.Servicing – The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.

3

ENGLISH

2INTRODUCTION

Thank you for choosing the DENON A/V Surround receiver. This remarkable component has been engineered to provide superb surround sound listening with home theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite music sources.

As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the contents of this manual before proceeding.

TABLE OF CONTENTS

z Before Using ..............................................................................................	4
x Cautions on Installation ..............................................................................	5
c Cautions on Handling .................................................................................	5
v Features......................................................................................................	5
b Part Names and Functions .....................................................................	6, 7
n Read this first .............................................................................................	8
m Setting up the Speaker Systems................................................................	8
, Connections .........................................................................................	9~15
. Using the Remote Control Unit................................................................	16
⁄0Setting up the system .......................................................................	17~21

⁄1Remote Control Unit ..........................................................................	22~24
⁄2Operation ...................……………………………………………………25~29
⁄3Surround.............................................................................................	30~34
⁄4DSP Surround Simulation .........…………………………………………35~39
⁄5Listening to the Radio........................................................................	40~42
⁄6Last Function Memory .............................................................................	43
⁄7Initialization of the Microprocessor ......................…………………………43
⁄8Additional Information........................................................................	44~46
⁄9Troubleshooting ........................................................................................	47
¤0Specifications ...........................................................................................	48
List of Preset Codes..................................................................................	94, 95

2ACCESSORIES

Check that the following parts are included in addition to the main unit:

q Operating instructions ............................................................................	1
w Warranty ( for North America model only ) ............................................	1
e Service station list...................................................................................	1
r Remote control unit (RC-897) .................................................................	1

t R6P/AA batteries ....................................................................................	2
y AM loop antenna ....................................................................................	1
u FM indoor antenna..................................................................................	1
i FM antenna adaptor................................................................................	1

r

t

y

u

i

1 BEFORE USING

Pay attention to the following before using this unit:

•Moving the set

To prevent short circuits or damaged wires in the connection cords, always unplug the power cord and disconnect the connection cords between all other audio components when moving the set.

•Before turning the power operation switch on

Check once again that all connections are proper and that there are not problems with the connection cords. Always set the power operation switch to the standby position before connecting and disconnecting connection cords.

•Store this instructions in a safe place.

After reading, store this instructions along with the warranty in a safe place.

•Note that the illustrations in this instructions may differ from the actual set for explanation purposes.

• V. AUX terminal		OPTICAL VIDEO L AUDIO R	MODE
		V.AUX INPUT	SURROUND SELECT	CH VOL
The AVR-1802’s front	panel is	EAT
			SURROUND	TONE
			PARAMETER	CONTROL
equipped with a V. AUX terminal.
Remove the cap covering the
terminal when you want to use
it.

4

ENGLISH

	2	CAUTIONS ON INSTALLATION
Noise or disturbance of the picture may be generated if this unit or			0.3 ft (10 cm) or more
any other electronic equipment using microprocessors is used near a
tuner or TV.			B
If this happens, take the following steps:
•	Install this unit as far as possible from the tuner or TV.
•	Set the antenna wires from the tuner or TV away from this unit’s
	power cord and input/output connection cords.

•Noise or disturbance tends to occur particularly when using indoor antennas or 300 Ω /ohms feeder wires. We recommend using

outdoor antennas and 75 Ω /ohms coaxial cables.

0.3 ft (10 cm) or more

For heat dispersal, leave at least 0.3 ft (10 cm) of space between

the top, back and sides of this unit and the wall or other

components.

wall

3CAUTIONS ON HANDLING

•Switching the input function when input jacks are not connected

A clicking noise may be produced if the input function is switched when nothing is connected to the input jacks. If this happens, either turn down the MASTER VOLUME control or connect components to the input jacks.

•Muting of PRE OUT jack, HEADPHONE jack and SPEAKER terminals

The PRE OUT jack, HEADPHONE jack and SPEAKER terminals include a muting circuit. Because of this, the output signals are greatly reduced for several seconds after the power operation switch is turned on or input function, surround mode or any other set-up is changed.

If the volume is turned up during this time, the output will be very high after the muting circuit stops functioning. Always wait until the muting circuit turns off before adjusting the volume.

•Whenever the power operation switch is in the STANDBY state, the apparatus is still connected on some AC line voltages.

Please be sure to unplug the cord when you leave home for, say, a vacation.

4FEATURES

1.Dolby Pro Logic II decoder

Dolby Pro Logic II is a new format for playing multichannel audio signals that offers improvements over conventional Dolby Pro Logic. It can be used to decode not only sources recorded in Dolby Surround but also regular stereo sources into five channels (front left/right, center and surround left/right). In addition, various parameters can be set according to the type of source and the contents, so you can adjust the sound field with greater precision.

2.Dolby Digital decoder

Dolby Digital, a digital discrete system in which the different channels are completely independent, recreates “threedimensional” sound fields (sounds with a sense of distance, movement and position) with no crosstalk between channels for greater reality. In addition, the 5 channels (excluding the 0.1 channel for low frequency effects) have a playback range extending to 20 kHz, the same as the range of CDs, thus resulting in clearer, more richly expressive sound.

3.DTS (Digital Theater Systems) decoder

DTS provides up to 5.1 channels of wide-range, high fidelity surround sound, from sources such as laser disc, DVD and specially-encoded music discs.

4.High performance DSP simulates 7 sound fields

Playback is possible in 7 surround modes: 5-channel Stereo, Mono Movie, Rock Arena, Jazz Club, Video Game, Matrix and Virtual. You can enjoy a variety of sound effects for different movie scenes and program sources even with stereo sources not in Dolby Surround.

5.Personal Memory Plus function

Personal Memory Plus is an advanced version of Personal Memory. With Personal Memory Plus, the set automatically memorizes the surround mode, channel volume, surround parameters, etc., for each of the separate input sources.

6.Remote control unit with pre-memory function

This unit comes with a remote control unit equipped with a prememory function. The remote control command codes for DENON remote controllable AV components as well as for DVD players, LD players, video decks, TVs, etc., of other major manufacturers are prestored in the memory.

7.6CH EXT. IN jack

This unit is equipped with 6CH EXT. IN jacks for use with audio formats of the future.

5

ENGLISH

5 PART NAMES AND FUNCTIONS

Front Panel

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

#0 @9@8@7@6@5@4@3@2@1@0 !9!8!7

!6

B PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER

AVR-1802

MASTER VOLUME

CD

PHONO

REMOTE

VOLUME LEVEL

SENSOR

SIGNAL

DVD / VDP

TUNER

DIGITAL

INPUT

VCR-1

TV / DBS

ON / STANDBY

AUTO

PCM

DTS

CDR / TAPE

VCR-2

V. AUX

SHIFT

DOWN

UP

BAND

MODE

MEMORY

DOWN

UP

VIDEO SELECT

DIMMER

STATUS

PRESET

TUNING

ON / STANDBY

PHONES

SPEAKER

INPUT

V.AUX INPUT

SURROUND

SELECT

CH VOL

OPTICAL

VIDEO

L

AUDIO

MODE

R

A

B

INPUT MODE

ANALOG

EXT. IN

CINEMA EQ

TONE DEFEAT

SURROUND

TONE

PARAMETER

CONTROL

t

u

o

!2

q w e r

y i

!0 !1

!3!4!5

q Power operation switch ..............................................	(18, 25, 40)
w Headphones jack (PHONES)....................................................	(28)
e Preset stations selector buttons..............................................	(42)
r SPEAKER A/B buttons.................................................	(25, 28, 43)
t INPUT MODE button...................................................	(26, 29, 33)
y ANALOG button ................................................................	(26, 29)
u EXT. IN button ...................................................................	(26, 29)
i CINEMA EQ button .................................................................	(33)
o TONE DEFEAT button .............................................................	(27)
!0VIDEO SELECT button ............................................................	(28)
!1V. AUX INPUT jacks .............................................................	(4, 10)
!2SURROUND MODE button...................................	(27, 31, 33, 38)
!3SURROUND PARAMETER button.....................................	(31, 38)
!4SELECT knob ..................................................	(27, 30, 31, 33, 38)
!5TONE CONTROL button..........................................................	(27)

!6CH VOL button ........................................................................	(30)
!7MASTER VOLUME control......................................................	(27)
!8STATUS button ........................................................................	(28)
!9DIMMER button ......................................................................	(28)
@0Master volume indicator (VOLUME LEVEL)............................	(27)
@1Display
@2TUNING UP/DOWN button .....................................................	(41)
@3MEMORY button...............................................................	(40, 42)
@4MODE button ..........................................................................	(41)
@5BAND button ...........................................................................	(41)
@6SIGNAL indicators....................................................................	(27)
@7INPUT mode indicators............................................................	(27)
@8Remote control sensor (REMOTE SENSOR) ..........................	(19)
@9Power operation indicator
#0Input source selector buttons .....................................	(26, 31, 33)

6

ENGLISH

Remote control unit

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

Remote control signal
transmitter .........................................	(16)

INPUT MODE button	...................	(26, 29)
SURROUND MODE
button ........................	(27, 30, 31, 33, 36)
System buttons (TAPE, VCR)
buttons.........................................		(22, 24)
VIDEO SELECT button.......................		(28)

SYSTEM (SYSTEM SET UP)
buttons...............................................	(18)
Cursor buttons .......................	(17, 32, 36)
Test tone button.................................	(30)
System buttons (TV) ..........................	(24)

				CD	MD/CDR
			AUDIO		VIDEO
AVR/AVC	POWER				DVD/VDP
	TV			VCR
ON
	PHONO			CD	DVD/VDP
OFF	1			2	3
V. AUX	VCR-1			VCR-2	TV/DBS
4	5			6	7
INPUT MODE	CDR / TAPE			TUNER	SHIFT
8	9			0
SURROUND	TAPE·VCR
MODE
	6			7
0					CHANNEL
3	2			0
VIDEO SELECT	CD·MD/CDR·DVD/VDP				DISC SKIP+
TITLE
8		3		9
6		2			7
SYSTEM			SURROUND
SET UP	CH SELECT			MENU	MASTER
					VOL
	SELECT
T.TONE			STATUS		MUTING
RETURN			DISPLAY
CHANNEL		TV		VOLUME

B

REMOTE CONTROL UNIT RC-897

				Mode selector switch	(17, 22, 23)
				POWER buttons	(23, 24, 25)
				Input source selector
				buttons	(26, 31, 33)
				Preset stations select
				buttons	(22, 42)
				System buttons
				(CD, MD/CDR, DVD/VDP)	(22, 24)
				SURROUND (SURROUND PARAMETER)
				button	(31, 33, 34, 36)
				Master volume control
				...............................................buttons	(27)
				MUTING button	(28)
				STATUS button...................................	(28)

7

ENGLISH

6 READ THIS FIRST

This AV Surround Receiver must be setup before use. Following these steps.

Step 1 (page 8 to 15)

Choose the best location to setup the Speakers and connecting the components.

7 SETTING

2 Speaker system layout

Basic system layout

• The following is an example of the basic layout for a system consisting of six speaker systems and a television monitor:

Subwoofer

Center speaker system

	Front speaker systems
	Set these at the sides of the TV or screen with
	their front surfaces as flush with the front of the	Surround speaker systems
	screen as possible.

8

			ENGLISH
8	CONNECTIONS
•	Do not plug in the power cord until all connections have been	• Note that binding pin plug cords together with power cords or
	completed.	placing them near a power transformer will result in generating
•	Be sure to connect the left and right channels properly (left with	hum or other noise.
	left, right with right).	• Noise or humming may be generated if a connected audio
•	Insert the plugs securely. Incomplete connections will result in	equipment is used independently without turning the power
	the generation of noise.	of this unit on. If this happens, turn on the power of this unit.
• Use the AC OUTLETS for audio equipment only. Do not
	use them for hair driers, etc.

•Analog recording of signals input to the AVR-1802 in digital format is not possible. To record in analog, also connect the analog signals of the player to the AVR-1802’s analog input terminals.

•The AVR-1802’s OPTICAL OUT terminal is an optical digital output terminal for connection of a CDR recorder, MD recorder or other digital recording device. Use it for digital recording.

Connecting the audio components

Connecting a turntable

Connect the turntable’s output cord to this unit’s PHONO jacks, the L (left) plug to the L jack, the R (right) plug to the right jack.

NOTE:

This unit cannot be used with MC cartridges directly. Use a separate head amplifier or step-up transformer.

If humming or other noise is generated when the ground wire is connected, disconnect the ground wire.

Turntable (MM cartridge)

L

R

SIGNAL

GND

Ground wire

ANTENNA TERMINALS

	LOOP	AM
	ANT.

					FM
					COAX.
					75
				L
				R
				FR	FL
				SW	C
				SR	SL
					REXT. INL
FRONT	SUBWOOFER	CENTER	SURROUND	LINE OUT

Decoders with 6-channel analog outputs, etc.

INPUT		OUTPUT Tape deck or CD recorder		Connecting a tape deck
R	L	R	L	Connections for recording:
				Connect the tape deck’s recording input jacks (LINE IN or REC) to this
R	L	R	L	unit’s tape recording (OUT) jacks using pin plug cords.
				Connections for playback:
				Connect the tape deck’s playback output jacks (LINE OUT or PB) to
		LINE OUT		this unit’s tape playback (IN) jacks using pin plug cords.
LINE IN				Connecting the pre-out jacks

Use these jacks if you wish to connect external power amplifier(s) to increase the power of the front and center channels, or for connection to powered loudspeakers. Connect the internal amplifier’s subwoofer to the subwoofer terminal. (Refer to page 14.)

AC CORD

AC 120V, 60Hz

R

L

R

L

PHONO

CDR /

TAPE

CDR /

TAPE

DVD/

TV/

VCR-1

VCR-2

VCR-1

VCR-2

MONITOR

VDP

DBS

CD

MONITOR

FRONT

S-VIDEO

DVD /

DVD /

CENTER

VDP

VDP

SUB

TV /

COAX.

TV /

WOOFER

DBS

DBS

PREOUT

SPEAKER SYSTEMS

AC OUTLETS

VCR

VCR-1

-1

FRONT

CENTER

SURROUND

AC 120V 60Hz

SWITCHED

VCR

OPT-1

VCR-2

TOTAL 120W(1A.)MAX.

-2

VCR

OPT-2

VCR-1

-1

VCR

OPT-2

VCR-2

-2

AUDIO

DIGITAL

VIDEO

SPEAKER IMPEDANCE

FRONT A OR B / 6

16

CENTER

/ 6

16

A + B / 12

16

SURROUND / 6

16

Connecting the AC OUTLETS AC OUTLETS

• SWITCHED

(total capacity – 120 W (1 A.))

The power to these outlets is turned on and off in conjunction with the POWER switch on the main unit, and when the power is switched between on and standby from the remote control unit.

No power is supplied from these outlets when this unit’s power is at standby. Never connect equipment whose total capacity is above 120 W (1 A.)

NOTE:

Only use the AC OUTLETS for audio equipment. Never use them for hair driers, TVs or other electrical appliances.

9

ENGLISH

OUTPUT R L

R L

LINE OUT

DIGITAL OUT

				CD player		OUTPUT
						COAXIAL	OPTICAL
	Connecting a CD player					OUT	OUT
Connect the CD player’s analog output
jacks (ANALOG OUTPUT) to this unit’s
CD jacks using pin plug cords.						DIGITAL	DIGITAL
		SIGNAL		PHONO		CDR /
		GND
						TAPE
	ANTENNA TERMINALS					CDR /
						TAPE
		R		CD		MONITOR
	LOOP
		L	AM
	ANT.			DVD /		DVD /
				VDP		VDP
		FM		TV /	COAX.	TV /
		COAX.		DBS		DBS
		75
				VCR		VCR-1
				-1
	FR		FL	VCR	OPT-1	VCR-2
IN	SW		C		OPT-2	VCR-1
DIGITAL	SR		SL	-2	OPT-2	VCR-2
		EXT. IN		AUDIO	DIGITAL	VIDEO

CD player, etc. equipped with DIGITAL output

DIGITAL jacks

Use these for connections to audio equipment with digital output. Refer to page 21 for instructions on setting this terminal.

•Use 75 Ω /ohms cable pin cords (sold separately) for coaxial connections.

•Use optical cables (sold separately) for optical connections, removing the cap before connecting.

DVD/	TV/	VCR-1	VCR-2	VCR-1		VCR-2	MONITOR
VDP	DBS
FRONT			S-VIDEO
		CENTER
		SUB
		WOOFER
PREOUT				SPEAKER SYSTEMS						AC OUTLETS
			FRONT				CENTER	SURROUND		AC 120V 60Hz
										SWITCHED
										TOTAL 120W(1A.)MAX.
		SPEAKER IMPEDANCE
		FRONT A OR B / 6			16		CENTER	/ 6	16
			A + B / 12		16		SURROUND / 6		16

	B	CD recorder, MD recorder or other component
OUTPUT INPUT		equipped with digital output jacks.
OPTICAL

Connecting the video equipments

To connect the video signal, connect using a 75 Ω /ohms video signal cable cord. Using an improper cable can result in a drop in sound quality.

			MASTER VOLUME
VOLUME LEVEL
VIDEO SELECT DIMMER		STATUS
V.AUX INPUT		SURROUND	SELECT	CH VOL
OPTICAL VIDEO	L	MODE
		AUDIO R
		SURROUND		TONE
		PARAMETER		CONTROL

L R

TV game

OUTPUT

R		L		OPTICAL			VIDEO OUT

R

L

LINE OUT	DIGITAL OUT	VIDEO OUT

Video camera

OUTPUT

R L

VIDEO OUT

R

L

LINE OUT

VIDEO OUT

Connecting a TV game equipment

•Connect the TV game equipment’s output jacks to this unit’s V. AUX INPUT lacks.

Connecting a video camera equipment

•Connect the video camera equipment’s output jacks to this unit’s V. AUX INPUT lacks.

The V. AUX terminal is covered with a cap. Remove this cap in order to use the terminal. (See page 4 for instructions on removing the cap.)

10

ENGLISH

AUDIO		VIDEO	DIGITAL
R	OUT	OUT	OUT
	L		OPTICAL

R L

TV or DBS tuner			Connecting a TV/DBS tuner
			TV/DBS
			• Connect the TV’s or DBS tuner’s video output jack (VIDEO OUTPUT)
			to the	VIDEO	(yellow) TV/DBS IN jack using a 75 Ω /ohms video
			coaxial pin plug cord.
			• Connect the TV’s or DBS tuner’s audio output jacks (AUDIO
			OUTPUT) to the			AUDIO	TV/DBS IN jacks using pin plug cords.

AUDIO OUT	VIDEO OUT

AUDIO OUT

AUDIO IN

OUT

AUDIO

VIDEO

DIGITAL

B

DVD player or video disc player (VDP)

OUT

OUT

R

L

OUT

COAXIAL

DIGITAL

R

L

Connecting a DVD player or a video disc player VDP

• Connect the DVD player’s (video disc player’s) video output jack (VIDEO OUTPUT) to the

VIDEO

(yellow) DVD/VDP

IN jack using a 75 Ω /ohms video coaxial pin plug cord.

AUDIOOUT

VIDEOOUT

DIGITALOUT

• Connect the DVD player’s (video disc player’s) analog audio output jacks (ANALOG AUDIO OUTPUT) to the AUDIO

DVD/VDP IN jacks using pin plug cords.

• For better sound quality, we recommend using the DVD player with digital rather than analog connections.

DVD players and VDP can also be connected to the VCR terminals.

VIDEO

IN

SIGNAL

PHONO

CDR /

GND

TAPE

VIDEO IN

Monitor TV

ANTENNA TERMINALS

CDR /

R

L

TAPE

LOOP

CD

MONITOR

AM

MONITOR OUT

ANT.

R

DVD /

DVD /

VDP

VDP

• Connect the TV’s video input jack (VIDEO

L

INPUT) to the

VIDEO

MONITOR OUT

FM

DBS

COAX.

DBS

COAX.

R75

TV /

TV /

jack using a 75 Ω /ohms video coaxial pin

L

VCR

VCR-1

-1

plug cord.

R

FR

VCR

OPT-1

VCR-2

FL

-2

L

SW

R C

VCR

OPT-2

VCR-1

-1

SR

L SL

VCR

OPT-2

VCR-2

-2

OPT.-1

AUDIO

DIGITAL

VIDEO

EXT. IN

R L

NOTE:

Connection of the video disc Player Equipped with Dolby Digital RF

OUT

IN

(AC-3RF) Output Jack.

• Please use a commercially available adaptor when connecting the

AUDIO

AUDIO

VIDEO OUT

Dolby Digital RF (AC-3RF) output jack of the video disc player to

connections.

the digital input jack.

VIDEO IN

Please refer to the instruction manual of the adapter when making

R

L

R

L

Video deck 2

R	L	R	L OUT IN
	OUT		IN
	AUDIO		VIDEO

VIDEO OUT

			VIDEO IN
R	L	R	Video deck 1
			L

R			L	R		L OUT IN
	OUT				IN
			AUDIO			VIDEO

Connecting a video decks

•There are two sets of video deck (VCR) jacks, so two video decks can be connected for simultaneous recording or video copying.

Video input/output connections:

•Connect the video deck’s video output jack (VIDEO OUT) to the VIDEO (yellow) VCR-1 IN jack, and the video deck’s video input jack (VIDEO IN) to the VIDEO (yellow) VCR-1 OUT jack using 75 Ω /ohms video coaxial pin plug cords.

Connecting the audio output jacks:

•Connect the video deck’s audio output jacks (AUDIO OUT) to the AUDIO VCR-1 IN jacks, and the video deck’s audio input jacks (AUDIO IN) to the AUDIO VCR-1 OUT jacks using pin plug cords.

Connect the second video deck to the VCR-2 jacks in the same way.

11

ENGLISH

Connecting a video component equipped with S-video jacks

•When marking connections, also refer to the operating instructions of the other components.

•A note on the S input jacks

The input selectors for the S inputs and pin jack inputs work in conjunction with each other.

•Precaution when using S-jacks

This unit’s S-jacks (input and output) and video pin jacks (input and output) have independent circuit structures, so that video signals input from the S-jacks are only output from the S-jack outputs and video signals input from the pin jacks are only output from the pin jack outputs. When connecting this unit with equipment that is equipped with S-jacks, keep the above point in mind and make connections according to the equipment’s instruction manuals.

Monitor TV

S-VIDEO

IN

Connecting a monitor TV

MONITOR OUT

•Connect the TV’s or DBS tuner’s S video input (S-VIDEO INPUT) to the S-VIDEO MONITOR OUT jack using a S jack connection cord.

Video deck 1

S-VIDEO

OUT IN

DVD/	TV/	VCR-1	VCR-2	VCR-1		VCR-2	MONITOR
VDP	DBS
			VIDEO
		CENTER
		SUB
		WOOFER
PREOUT				SPEAKER SYSTEMS						AC OUTLETS
			FRONT				CENTER	SURROUND		AC 120V 60Hz
										SWITCHED
										TOTAL 120W(1A.)MAX.
		SPEAKER IMPEDANCE
		FRONT A OR B / 6			16		CENTER	/ 6	16
			A + B / 12		16		SURROUND / 6		16

Connecting the video decks

•Connect the video deck’s S output jack (S-OUT) to the S-VIDEO VCR-1 IN jack and the video deck’s S input jack (S-IN) to the

S-VIDEO VCR-1 OUT jack using S jack connection cords.

•Connect the video deck’s S output jack (S-OUT) to the S-VIDEO VCR-2 IN jack and the video deck’s S input jack (S-IN) to the

S-VIDEO VCR-2 OUT jack using S jack connection cords.

Video deck 2

OUT IN

TV or satellite broadcast tuner

Connecting a TV/DBS tuner

S-VIDEO

OUT

DVD player, VDP, etc.

S-VIDEO B

OUT

•Connect the TV’s or DBS tuner’s S video output jack (S-VIDEO OUTPUT) to the S-VIDEO TV/DBS IN jack using an S jack

connection cord.

Connecting a DVD player or video disc player (VDP)

DVD/VDP

•Connect the DVD player’s or video disc player’s S-Video output jack to the S-VIDEO DVD/VDP IN jack using an S-Video connection cord.

Connect the components’ audio inputs and outputs as described on page 11.

12

ENGLISH

Connecting the antenna terminals
DIRECTION OF
BROADCASTING
STATION						AM LOOP
						ANTENNA
						(An Accessory)
	FM ANTENNA
		SIGNAL		PHONO		CDR /
		GND
						TAPE
		ANTENNA TERMINALS				CDR /
						TAPE
75 Ω /ohms	FEEDER	ANT.	AM	CD		MONITOR
COAXIAL	CABLE
CABLE		LOOP
				VDP		VDP
				DVD /		DVD /
		FM		TV /	COAX.	TV /
		COAX.		DBS		DBS
		75
				VCR		VCR-1
FM ANTENNA				-1
				VCR
ADAPTER		FR	FL		OPT-1	VCR-2
				-2
(An Accessory)		SW	C	VCR	OPT-2	VCR-1
				-1
		SR	SL	VCR	OPT-2	AM OUTDOOR
				-2		VCR-2
						ANTENNA
		EXT. IN		AUDIO	DIGITAL	VIDEO
FM INDOOR ANTENNA
(An Accessory)
						GROUND

AM loop antenna assembly

			Connect to the AM
	1	2	antenna terminals.
			3
		Remove the vinyl tie
		and take out the	Bend in the reverse
	4	connection line.	direction.

a. With the antenna on top any stable surface.

Mount

b. With the antenna attached to a wall.

Installation hole

Mount on wall, etc.

Connection of AM antennas

1. Push the lever.	2. Insert the		3. Return the lever.
	conductor.

FM antenna adapter assembly

Open the cover

PULL

CLAMP

PULL

ANTENNA ADAPTER

REMOVE

SHUT

CLAMP	14mm	19mm
	9mm	14mm
	5mm	5mm

	3C-2V	5C-2V
CLAMP	75 Ω /ohms COAXIAL CABLE

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Notes:

•Do not connect two FM antennas simultaneously.

•Even if an external AM antenna is used, do not disconnect the AM loop antenna.

•Make sure AM loop antenna lead terminals do not touch metal parts of the panel.

13

ENGLISH

Speaker system connections

•Connect the speaker terminals with the speakers making sure that like polarities are matched (<with <, >with >). Mismatching of polarities will result in weak central sound, unclear orientation of the various instruments, and the sense of direction of the stereo being impaired.

•When making connections, take care that none of the individual conductors of the speaker cord come in contact with adjacent terminals, with other speaker cord conductors, or with the rear panel.

NOTE:

NEVER touch the speaker terminals when the power is on.

Doing so could result in electric shocks.

Speaker Impedance

•When speaker systems A and B are use separately, speakers with an impedance of 6 to 16 Ω /ohms can be connected for use as front speakers.

•Be careful when using two pairs of front speakers (A + B) at the same time, since use of speakers with an impedance of 12 to 16 Ω /ohms.

•Speakers with an impedance of 6 to 16 Ω /ohms can be connected for use as center and surround speakers.

•The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with an impedance lower than the specified impedance are connected.

		Connecting the speaker cords
			Connecting banana plugs
1. Loosen by turning	2. Insert the cord.	3. Tighten by turning
counterclockwise.		clockwise.
			banana plug

Turn clockwise to tighten, then insert the banana plug.

FRONT SPEAKER SYSTEMS		FRONT SPEAKER SYSTEMS		CENTER SPEAKER SYSTEM
System B		System A

(L)

(R)

(L)

(R)

SIGNAL

PHONO

CDR /

GND

TAPE

ANTENNA TERMINALS

CDR /

TAPE

DVD/

TV/

VCR-1

VCR-2

VCR-1

VCR-2

MONITOR

VDP

DBS

CD

MONITOR

FRONT

S-VIDEO

LOOP

AM

ANT.

CENTER

DVD /

DVD /

VDP

VDP

FM

SUB

TV /

COAX.

TV /

WOOFER

COAX.

DBS

DBS

75

PREOUT

SPEAKER SYSTEMS

AC OUTLETS

VCR

VCR-1

-1

FRONT

CENTER

SURROUND

AC 120V 60Hz

SWITCHED

FR

FL

VCR

OPT-1

VCR-2

TOTAL 120W(1A.)MAX.

-2

SW

C

VCR

OPT-2

VCR-1

-1

SR

SL

VCR

OPT-2

VCR-2

-2

EXT. IN

AUDIO

DIGITAL

VIDEO

SPEAKER IMPEDANCE

FRONT A OR B / 6

16

CENTER

/ 6

16

A + B / 12

16

SURROUND / 6

16

			• Precautions when connecting speakers
			If a speaker is placed near a TV or video monitor, the
			colors on the screen may be disturbed by the
	(L)	(R)	speaker’s magnetism. If this should happen, move
			the speaker away to a position where it does not
			have this effect.
Connection jack for subwoofer with built-in	SURROUND SPEAKER SYSTEMS
amplifier (super woofer), etc.

To achieve Dolby Digital (AC-3) playback effect, use a unit that can sufficiently reproduce frequencies of under 80 Hz.

14

ENGLISH

Protector circuit

•This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the speakers under circumstances such as when the output of the power amplifier is inadvertently short-circuited and a large current flows, when the temperature surrounding the unit becomes unusually high, or when the unit is used at high output over a long period which results in an extreme temperature rise.

When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED flashes. Should this occur, please follow these steps: be sure to switch off the power of this unit, check whether there are any faults with the wiring of the speaker cables or input cables, and wait for the unit to cool down if it is very hot. Improve the ventilation condition around the unit and switch the power back on.

If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the unit, switch off the power and contact a DENON service center.

Note on speaker impedance

•The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with an impedance lower than the specified impedance (for example speakers with an impedance of lower than 4 Ω /ohms)

are connected. If the protector circuit is activated, the speaker output is cut off. Turn off the set’s power, wait for the set to cool down, improve the ventilation around the set, then turn the power back on.

15

ENGLISH

9 USING THE REMOTE CONTROL UNIT

Following the procedure outlined below, insert the batteries before using the remote control unit.

Range of operation of the remote control unit

Point the remote control unit at the remote control sensor as shown on the diagram at the left.

B

30° 30°

Approx. 23 feet/7 m

NOTES:

•The remote control unit can be used from a straight distance of approximately 23 feet/7 meters, but this distance will shorten or operation will become difficult if there are obstacles between the remote control unit and the remote control sensor, if the remote control sensor is exposed to direct sunlight or other strong light, or if operated from an angle.

•Neon signs or other devices emitting pulse-type noise nearby may result in malfunction, so keep the set as far away from such devices as possible.

Inserting the batteries

qPress as shown by the arrow and slide off.

w Insert the R6P/AA batteries properly, as	e Close the lid.
shown on the diagram.

NOTES:

•Use only R6P/AA batteries for replacement.

•Be sure the polarities are correct. (See the illustration inside the battery compartment.)

•Remove the batteries if the remote control transmitter will not be used for an extended period of time.

•If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

•Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the time comes.

•Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit is operated nearby the set. (The included battery is only for verifying operation. Replace it with a new battery as soon as possible.)

16

ENGLISH

10SETTING UP THE SYSTEM

•Once all connections with other AV components have been completed as described in “CONNECTIONS” (see pages 9 to 15), make the various settings described below on the display.

These settings are required to set up the listening room’s AV system centered around the this unit.

1	Set the slide switch to “AUDIO”.
	CD	MD/CDR
	AUDIO	VIDEO

2	Use the following buttons to set up the system:
	VIDEO SELECT CD·MD/CDR·DVD/VDP			DISC SKIP+
	TITLE
	8	3	9
	6	2		7
	SYSTEM	SURROUND
	SET UP		MENU	MASTER
	CH SELECT			VOL
	SELECT
	T.TONE		STATUS	MUTING
	RETURN		DISPLAY

SYSTEM SETUP button

Press this to display the system setup on the display.

CURSOR buttons (•, ª, 0, 1)

Press this change what appears on the display.

SELECT button

Press this to switch the display.

Also use this button to complete the setting.

• System setup items and default values (set upon shipment from the factory)

	System setup							Default settings
Speaker	Input the combination of speakers in your system and their				Front Sp.			Center Sp.	Surround Sp.		Sub Woofer
	corresponding sizes (SMALL for regular speakers, LARGE for full-size,
Configuration	full-range) to automatically set the composition of the signals output				Large			Small	Small		Yes
	from the speakers and the frequency response.
Subwoofer Mode	This selects the subwoofer speaker for playing deep bass							Subwoofer mode = Normal
	signals.
	This parameter is for optimizing the timing with which the audio			Front & Subwoofer				Center	Surround L & R		—
Delay Time	signals are produced from the speakers and subwoofer according to
	the listening position.				12 ft (3.6 m)			12 ft (3.6 m)	10 ft (3.0 m)		—
			Digital	COAXIAL			OPTICAL-1	OPTICAL-2
	This assigns the digital input jacks for the different input		Inputs
Digital Input
	sources.		Input	DVD/VDP			TV/DBS	CDR/TAPE
			source
Channel Level	This adjusts the volume of the signals output from the speakers and			Front L	Front R		Subwoofer	Center	Surround L	Surround R	—
	subwoofer for the different channels in order to obtain		optimum
	effects.			0 dB	0 dB		0 dB	0 dB	0 dB	0 dB	—

NOTE:

• The system setup is not displayed when “HEADPHONE ONLY” is selected.

17

ENGLISH

Before setting up the system

1	Check that all the components are correct, then press the POWER operation switch on the main unit or
	the POWER button on the remote control unit to turn on the power.

(Main unit)

(Remote control unit)

2

3

Press the SYSTEM button to enter the setting.

*SYSTEM SET UP

NOTE: Please make sure the “AUDIO” position of the slide switch on the remote control unit.

Press the SELECT or (down) button to switch to the speaker configuration set up.

NOTE:

Press the SYSTEM button again to finish system set up. System set up can be finished at any time. The changes to the settings made up to that point are entered.

Setting the speaker configuration

1	Use the	(left) and (right) buttons to select your front speaker type.
				(Initial)
		1 FRONT	LARGE	LARGE	SMALL
				(left) button	(right) button

Press the SELECT or (down) button to switch to the center speaker setting.

2	Use the	(left) and	(right) buttons to select your center speaker type.
			(Initial)

2 CENTER SMALL

LARGE SMALL NONE

(left) button

(right) button

Press the SELECT or (down) button to switch to the surround speaker setting.

NOTE:

• When “Small” has been selected for the front speakers, “Large” cannot be selected for the center speaker.

3	Use the	(left) and	(right) buttons to select your surround speaker type.
			(Initial)

3 SURR. SMALL

LARGE SMALL NONE

(left) button

(right) button

Press the SELECT or (down) button to switch to the subwoofer setting.

18

ENGLISH

NOTE:

• When “Small” has been selected for the front speakers, “Large” cannot be selected for the surround speakers.

4	Use the	(left) and	(right) buttons to select your subwoofer setting.
			(Initial)

YES NO

4 S.WOOFER YES

(left) button

(right) button

Press the SELECT or (down) button to enter the settings and switch to the SUBWOOFER MODE setting.

•Parameters

Large…… Select this when using speakers that can fully reproduce low sounds of below 80 Hz.

Small…… Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient volume. When this setting is selected, low frequencies of below 80 Hz are assigned to the subwoofer.

None…… Select this when no speakers are installed.

Yes/No…. Select “Yes” when a subwoofer is installed, “No” when it’s not installed.

NOTE:

Select “Large” or “Small” not according to the physical size of the speaker, but according to the bass reproduction capacity at 80 Hz. If you cannot determine the best setting, try comparing the sound when set to “Small” and when set to “Large”, at a level that will not damage the speakers.

Caution:

In case the subwoofer is not used, be sure to set “Subwoofer = No”, or the bass sound of front channel is divided to subwoofer channel and not reproduced in some mode.

Setting the SUBWOOFER MODE

1	Use the	(left) and	(right) buttons to select the Subwoofer mode.
			(Initial)

NORM +MAIN

5 SW MODE NORM

(left) button

(right) button

Press the SELECT or (down) button to enter the setting and switch to the SPEAKER DISTANCE setting.

NOTES:

— Assignment of low frequency signal range —

• The signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or DTS signals) and the low frequency signal range of channels set to “SMALL” in the setup. The low frequency signal range of channels set to “LARGE” are produced from those channels.

— Subwoofer mode —

•The subwoofer mode setting is only valid when “LARGE” is set for the front speakers and “YES” is set for the subwoofer in the “Speaker Configuration” settings (see pages 18, 19).

If “SMALL” is set for the front speakers or “NO” is set for the subwoofer, the subwoofer mode setting does not affect playback of low frequency signal range.

•When the “+MAIN” playback mode is selected, the low frequency signal range of channels set to “LARGE” are produced simultaneously from those channels and the subwoofer channel.

In this playback mode, the low frequency range expand more uniformly through the room, but depending on the size and shape of the room, interference may result in a decrease of the actual volume of the low frequency range.

•When the “NORM” playback mode is selected, the low frequency signal range of channels set to “LARGE” are only produced from those channels. In this playback mode there tends to be little interference of the low frequency range in the room.

•Try playing the music or movie source and select the playback mode providing the stronger low frequency range sound.

19

ENGLISH

Setting the delay time

Input the distances from the listening position to the speakers and set the surround delay time.

Preparations:

Measure the distances from the listening position to the speakers (L1 to L3 on the diagram at the right). L1: Distance from center speaker to listening position

L2: Distance from front speakers to listening position L3: Distance from surround speaker to listening position

CAUTION:

Set the center speaker at the same distance from the front speakers (left and right) or the subwoofer, or so that the difference in distance (L2 – L1) is 5 feet or less.

Set the surround speakers (left and right) at the same distance from the front speakers (left and right) or the subwoofer, or so that the difference in distance (L2 – L3) is 15 feet or less.

FL Center FR

L2	L1	Listening
		position
	L3

SL SR

1	Use the	(left) and	(right) buttons to set the distance from the front speakers and subwoofer to the
	listening position.

6 FRNT/SW 12ft

•The number changes in units of 1 foot each time one of the buttons is pressed. Select the value closest to the measured distance.

(“/SW” appears only when subwoofer = yes.)

Press the SELECT or (down) button to switch to the center speaker setting.

NOTE:

• The speaker distance can be adjusted between 0 and 60 feet in steps of 1 foot.

2	Use the	(left) and	(right) buttons to set the distance from the center speakers to the listening
	position.

7 CENTER 12ft

•The number changes in units of 1 foot each time one of the buttons is pressed. Select the value closest to the measured distance.

Press the SELECT or (down) button to switch to the surround speaker setting.

NOTE:

• No setting when “None” has been selected for the center speaker.

3	Use the	(left) and	(right) buttons to set the distance from the surround speakers to the listening
	position.

8 SURR. 10ft

•The number changes in units of 1 foot each time one of the buttons is pressed. Select the value closest to the measured distance.

Press the SELECT or (down) button to enter the setting and switch the DIGITAL input (COAX) setting.

NOTE:

• No setting when “None” has been selected for the surround speakers.

20

ENGLISH

Digital input setup

Input the type of components connected to the digital input terminals.

1	Use the	(left) and	(right) buttons to set the type of device connected to the COAXIAL input (COAXIAL)
	terminal.
				(Initial)
			CD	DVD	TV	VCR1	VCR2	CDR	OFF
9 COAX		DVD
					(left) button		(right) button
	• Select “OFF” if nothing is connected.
	Press the SELECT or		(down) button to switch the optical input 1 (OPT 1) setting.
2	Use the	(left) and	(right) buttons to set the type of device connected to the OPTICAL input (OPTICAL)
	terminal.
					(Initial)
			CD	DVD	TV	VCR1	VCR2	CDR	OFF
10 OPT1		TV
					(left) button		(right) button
	• Select “OFF” if nothing is connected.
	Press the SELECT or		(down) button to switch the optical input 2 (OPT 2) setting.
3	Use the	(left) and	(right) buttons to set the type of device connected to the OPTICAL input (OPTICAL)
	terminal.
								(Initial)
			CD	DVD	TV	VCR1	VCR2	CDR	OFF
11 OPT2		CDR
					(left) button		(right) button
	• Select “OFF” if nothing is connected.
	Press the SELECT or		(down) button if you want to start the settings over front the beginning.

NOTE: PHONO, TUNER and V. AUX cannot be selected.

After setting up the system

1	Press the SYSTEM button to finish system set up.

This completes the system setup operations. Once the system is set up, there is no need to make the settings again unless other components or speakers are connected to or the speaker layout is changed.

21

ENGLISH

11 REMOTE CONTROL UNIT

Operating DENON audio components

DENON remote-controllable audio components can be controlled using this unit’s remote control unit.

Note that some components, however, cannot be operated with this remote control unit.

				CD	MD/CDR	1
			AUDIO		VIDEO
		POWER
	AVR/AVC	TV		VCR	DVD/VDP
	ON
		PHONO		CD	DVD/VDP
	OFF	1		2	3
	V. AUX	VCR-1		VCR-2	TV/DBS
	4	5		6	7	2-c
	INPUT MODE	CDR / TAPE		TUNER	SHIFT
	8	9		0
	SURROUND	TAPE·VCR
	MODE
		6		7
2-b	0				CHANNEL
	3	2		0
	VIDE SELECT	CD·MD/CDR·DVD/VDP			DISC SKIP+
	TITLE
2-a	8		3	9
	6		2		7
	SYSTEM		SURROUND
	SET UP	CH SELECT		MENU	MASTER
					VOL
		SELECT
	T.TONE		STATUS		MUTING
	RETURN		DISPLAY
	CHANNEL		TV	VOLUME
		B
	REMOTE CONTROL UNIT RC-897

1	Set the slide switch to the position for the component to					CD	MD/CDR
	be operated (CD or MD/CDR).
						AUDIO	VIDEO
2
	Use the buttons shown below to operate the audio component.
	For details, refer to the respective component’s manual.
	a. For CD player and MD/CD recorder
	VIDEO SELECT CD·MD/CDR·DVD/VDP DISC SKIP+			6,7 : Manual search (reverse and forward)
				2	: Stop
	TITLE			1	: Play
	8	3	9	8,9	: Auto search
	6	2	7	3	: Pause
	SYSTEM	SURROUND		DISC SKIP+ : Switch discs (for CD changers only)

b. For tape deck (TAPE)

V. AUX	VCR-1	VCR-2	TV/DBS
4	5	6	7
INPUT MODE	CDR / TAPE	TUNER	SHIFT
8	9	0

SURROUND

MODE TAPE·VCR

6 7

0CHANNEL

3

2

0

c. For TUNER

V. AUX	VCR-1	VCR-2	TV/DBS
4	5	6	7
INPUT MODE	CDR / TAPE	TUNER	SHIFT
8	9	0
SURROUND	TAPE·VCR
MODE

6 7

0CHANNEL

3

2

0

6: Rewind

7: Fast-forward

2: Stop

1 : Forward play

0: Reverse play

SHIFT : Switch preset channel range CHANNEL : Preset channel up/down

(+, –)

NOTE:

• Tape deck (TAPE) and tuner can be operated when the switch is at “AUDIO” position.

Preset memory (Audio component)

		CD	MD/CDR
		AUDIO	VIDEO
	POWER
AVR/AVC	TV	VCR	DVD/VDP
ON
	PHONO	CD	DVD/VDP
OFF	1	2	3
V. AUX	VCR-1	VCR-2	TV/DBS
4	5	6	7
INPUT MODE	CDR / TAPE	TUNER	SHIFT
8	9	0
SURROUND	TAPE·VCR
MODE

6 7

0CHANNEL

2	3	2		0
	VIDEO SELECT	CD·MD/CDR·DVD/VDP			DISC SKIP+
	TITLE
	8		3	9
	6		2		7
	SYSTEM		SURROUND
	SET UP	CH SELECT		MENU	MASTER
					VOL
		SELECT
	T.TONE		STATUS		MUTING
	RETURN		DISPLAY
	CHANNEL		TV	VOLUME
		B
	REMOTE CONTROL UNIT RC-897

1

2

DENON components can be operated by setting the preset memory for MD or CDR. Operation in not possible for some models.

1	Set the slide switch to “MD/CDR”.
2	Holding in the PLAY (1) button, press the button for the
	components you want to set. (Refer to table 1.)
	Table 1: Combinations of Personal System
		Codes
					MASTER
				MASTER	VOL.
				VOL.
		PLAY (1)		MD	CDR

CD MD/CDR

AUDIOVIDEO

B

NOTE:

• The memory can only be preset for either the MD or the CDR.

Preset codes set upon shipment from the factory and when reset.

22

ENGLISH

Preset memory (Video component)

DENON and other makes of components can be operated by setting the preset memory for your make of video component.

This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the manufacturer of the component as shown on the List of Preset Codes (pages 94, 95).

Operation is not possible for some models.

1	Set the slide switch to “VIDEO”.		CD			MD/CDR
		AUDIO						VIDEO

CD MD/CDR

		AUDIO	VIDEO
	POWER
AVR/AVC	TV	VCR	DVD/VDP
ON
	PHONO	CD	DVD/VDP
OFF	1	2	3
V. AUX	VCR-1	VCR-2	TV/DBS
4	5	6	7
INPUT MODE	CDR / TAPE	TUNER	SHIFT
8	9	0
SURROUND	TAPE·VCR
MODE

6 7

0CHANNEL

3	2		0
VIDEO SELECT	CD·MD/CDR·DVD/VDP			DISC SKIP+
TITLE
8		3	9
6		2		7
SYSTEM		SURROUND
SET UP	CH SELECT		MENU	MASTER
				VOL
	SELECT
T.TONE			STATUS	MUTING
RETURN			DISPLAY

CHANNEL TV VOLUME

B

REMOTE CONTROL UNIT RC-897

1

2

3

2. 3

2	Holding in the SHIFT button q, press the POWER
	button w of the components (DVD/VDP, VCR or TV) you	w
	want to set.	q

Press and hold in the SHIFT button.

		B
3	Holding in the SHIFT button q, press the number	q w
	buttons w to input the preset code (consisting of 2-digit
	numbers) for the manufacturer of the component

whose signals you want to store in the memory.

See the list on pages 94 and 95 for the preset codes (consisting of 2-digit numbers).

4	To continue registering other components, repeat steps 2 to 3.

NOTES:

•The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental operation, cover the remote control unit’s transmitting window while setting the preset memory.

•Some models and years of manufacture of components of the manufacturers listed on the List of Preset Codes cannot be used.

•The unit is equipped with several types of remote control codes which depend on the manufacturer. If there is no operation, please change the preset code (a 2-digit number) and try again.

23

ENGLISH

Operating a video component stored in the preset memory

1

Set the slide switch to “VIDEO”.

CD

MD/CDR

AUDIO

VIDEO

2

Operate the video component.

•

For details, refer to the component’s operating instructions.

Some models cannot be operated with this remote control unit.

a. For DVD player

		CD	MD/CDR
		AUDIO	VIDEO
	POWER
AVR/AVC	TV	VCR	DVD/VDP
ON
	PHONO	CD	DVD/VDP
OFF	1	2	3
V. AUX	VCR-1	VCR-2	TV/DBS
4	5	6	7
INPUT MODE	CDR / TAPE	TUNER	SHIFT
8	9	0
SURROUND	TAPE·VCR
MODE

6 7

0CHANNEL

3	2		0
VIDEO SELECT	CD·MD/CDR·DVD/VDP			DISC SKIP+
TITLE
8		3	9
6		2		7
SYSTEM		SURROUND
SET UP	CH SELECT		MENU	MASTER
				VOL
	SELECT
T.TONE		STATUS		MUTING
RETURN		DISPLAY
CHANNEL		TV	VOLUME

B

REMOTE CONTROL UNIT RC-897

POWER : Turns power on and off 2 : Stop

1: Play

8,9 : Auto search (cue)

6,7 : Manual search (forward and reverse)

3: Pause

TITLE	: Call out title
MENU	: Call out menu
DISPLAY	: Switch display
SET UP	: DVD setup
RETURN	: Menu return
•,ª	: Cursor up/down
0,1	: Cursor left/right
SELECT	: Enter setting

NOTE:

Some manufacturers use different names for the DVD remote control buttons, so also refer to the instructions on remote control for that component.

b. For video disc player (VDP)

POWER

AVR/AVC	TV		VCR	DVD/VDP
ON
	PHONO		CD	DVD/VDP
OFF	1		2	3
V. AUX	VCR-1		VCR-2	TV/DBS
4	5		6	7
INPUT MODE	CDR / TAPE		TUNER	SHIFT
8	9		0
SURROUND	TAPE·VCR
MODE
	6		7
0				CHANNEL
3	2		0
VIDEO SELECT	CD·MD/CDR·DVD/VDP			DISC SKIP+
TITLE
8		3	9
6		2		7
SYSTEM		SURROUND
SET UP	CH SELECT		MENU	MASTER
				VOL
	SELECT
T.TONE		STATUS		MUTING
RETURN		DISPLAY
CHANNEL		TV	VOLUME

c. For video deck (VCR)

POWER

AVR/AVC	TV	VCR	DVD/VDP
ON
	PHONO	CD	DVD/VDP
OFF	1	2	3
V. AUX	VCR-1	VCR-2	TV/DBS
4	5	6	7
INPUT MODE	CDR / TAPE	TUNER	SHIFT
8	9	0
SURROUND	TAPE·VCR
MODE

6 7

0CHANNEL

3	2		0
VIDEO SELECT	CD·MD/CDR·DVD/VDP			DISC SKIP+
TITLE
8		3	9
6		2		7
SYSTEM		SURROUND
SET UP	CH SELECT		MENU	MASTER
				VOL
	SELECT
T.TONE		STATUS		MUTING
RETURN		DISPLAY
CHANNEL		TV	VOLUME

d. For monitor TV

POWER

AVR/AVC	TV	VCR	DVD/VDP
ON
	PHONO	CD	DVD/VDP
OFF	1	2	3
V. AUX	VCR-1	VCR-2	TV/DBS
4	5	6	7
INPUT MODE	CDR / TAPE	TUNER	SHIFT
8	9	0
SURROUND	TAPE·VCR
MODE

6 7

0CHANNEL

3	2		0
VIDEO SELECT	CD·MD/CDR·DVD/VDP			DISC SKIP+
TITLE
8		3	9
6		2		7
SYSTEM		SURROUND
SET UP	CH SELECT		MENU	MASTER
				VOL
	SELECT
T.TONE		STATUS		MUTING
RETURN		DISPLAY
CHANNEL		TV	VOLUME

POWER	: Power on/off	POWER	: Power on/off	POWER	: Power on/off
6,7	: Manual search	6,7	: Manual search	VOLUME	: Volume up/down
	(forward and reverse)		(forward and reverse)	(•,ª)
2	: Stop	2	: Stop	CHANNEL : Switch channel
1	: Play	1	: Play	(+, –)
8,9	: Auto search (cue)	3	: Pause
3	: Pause	CHANNEL : Switch channel
		(+, –)

NOTE: The TV can be operated when the switch is at any position.

24

12 OPERATION

Before operating

B

1		2
				CD	MD/CDR
				AUDIO	VIDEO
	1		POWER		DVD/VDP
		AVR/AVC	TV	VCR
		ON
			PHONO	CD	DVD/VDP
		OFF	1	2	3
		V.AUX	VCR-1	VCR-2	TV/DBS
		4	5	6	7

ENGLISH

Preparations:

Check that all connections are proper.

1	Turn on the power.
	Press ON/STANDBY on the main unit or the AVR/AVC on the
	remote control unit to turn on the power

(Main unit)

(Remote control unit)

•ON/STANDBY

When the button is pressed, the power turns on and the display lights after approximately 1 second.

When pressed again, the power turns off, the standby mode is set and the display turns off.

Several seconds are required from the time the power operation switch is set to the “ON” position until sound is output. This is due to the built-in muting circuit that prevents noise when the power switch is turned on and off.

2	Select the front speakers.
	Press SPEAKER A or B turn the speaker on.

(Main unit)

25

ENGLISH

Playing the input source

1

5

B

2 3

1	Press the button for the program source to be played.
	EX 1: CD
		CD
	(Main unit)	(Remote control unit)
	EX 2: CDR/TAPE
		CDR / TAPE
	(Main unit)	(Remote control unit)
2	Select the input mode.
	To select the input mode from main unit.

• Selecting the analog mode.

Press ANALOG to switch to the analog input.

(Main unit)

•Selecting the external input (EXT. IN) mode.

(In this case play the component connected to the “EXT. IN” terminal.)

Press EXT. IN to switch the external input.

(Main unit)

•Selecting the AUTO, PCM and DTS modes.

The mode switches as shown below each time INPUT MODE is pressed.

AUTO PCM

DTS

(Main unit)

To select the input mode from the remote control unit.

•The mode switches as shown below each time INPUT MODE is pressed.

AUTO PCM DTS ANALOG

EXT. IN

(Remote control unit)

				CD	MD/CDR
			AUDIO		VIDEO
		POWER
	AVR/AVC	TV		VCR	DVD/VDP
	ON
		PHONO		CD	DVD/VDP
	OFF	1		2	3
	V. AUX	VCR-1		VCR-2	TV/DBS	1
	4	5		6	7
2	INPUT MODE	CDR / TAPE		TUNER	SHIFT
	8	9		0
	SURROUND	TAPE·VCR
3	MODE
		6		7
	0				CHANNEL
	3	2		0
	VIDEO SELECT	CD·MD/CDR·DVD/VDP			DISC SKIP+
	TITLE
	8		3	9
	6		2		7
	SYSTEM		SURROUND			5
	SET UP	CH SELECT		MENU	MASTER
					VOL
		SELECT
	T.TONE		STATUS		MUTING
	RETURN		DISPLAY
	CHANNEL		TV	VOLUME
		B
	REMOTE CONTROL UNIT RC-897

Input mode selection function

Different input modes can be selected for the different input sources. The selected input modes for the separate input sources are stored in the memory.

qAUTO (All auto mode)

In this mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected and the program in this unit’s surround decoder is selected automatically upon playback. This mode can be selected for all input sources other than PHONO, CDR/TAPE and TUNER.

The presence or absence of digital signals is detected, the signals input to the digital input jacks are identified and decoding and playback are performed automatically in DTS, Dolby Digital or PCM (2 channel stereo) format. If no digital signal is being input, the analog input jacks are selected.

Use this mode to play Dolby Digital signals.

wPCM (exclusive PCM signal playback mode)

Decoding and playback are only performed when PCM signals are being input.

Note that noise may be generated when using this mode to play signals other than PCM signals.

eDTS (exclusive DTS signal playback mode)

Decoding and playback are only performed when DTS signals are being input.

rANALOG (exclusive analog audio signal playback mode)

The signals input to the analog input jacks are decoded and played.

tEXT. IN (external decoder input jack selection mode)

The signals being input to the external decoder input jacks are played without passing through the surround circuitry.

NOTE:

•Note that noise will be output when CDs or LDs recorded in DTS format are played in the “PCM” (exclusive PCM signal playback) or “ANALOG” (exclusive analog audio signal playback) mode. Select the AUTO or DTS (exclusive DTS signal playback) mode when playing signals recorded in DTS from a laser disc player.

Notes on playing a source encoded with DTS

•Noise may be generated at the beginning of playback and while searching during DTS playback in the AUTO mode. If so, play in the DTS mode.

•In some rare cases noise may be generated when you preform the operation to stop playback of a DTS-CD or DTS-LD.

26

	3	Select the play mode.
		Press the SURROUND MODE button, then turn SELECT
		knob.

	SURROUND
SELECT	MODE

(Main unit) (Remote control unit)

To select the surround mode while adjusting the surround parameters, channel volume or tone control, press the surround mode button then operate the selector.

(Main unit)

Start playback on the selected component.

4 • For operating instructions, refer to the component’s manual.

5	Adjust the volume.	MASTER VOLUME
			MASTER
			VOL
	The volume level is	(Main unit)	(Remote control unit)
	displayed on the

master volume level display.

The volume can be adjusted within the range of –60 to 0 to 18 dB, in steps of 1 dB. However, when the channel level is set as described on page 30, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume adjustment range is “18 dB — (Maximum value of channel level)”.)

Input mode when playing DTS sources

•Noise will be output if DTS-compatible CDs or LDs are played in the “ANALOG” or “PCM” mode.

When playing DTS-compatible sources, be sure to connect the source component to the digital input jacks (OPTICAL/COAXIAL) and set the input mode to “DTS”.

ENGLISH

Input mode display

• In the AUTO mode

	INPUT
AUTO	PCM	DTS

• In the DIGITAL PCM mode

	INPUT
AUTO	PCM	DTS

• In the DIGITAL DTS mode

	INPUT
AUTO	PCM	DTS

• In the ANALOG mode

	INPUT
AUTO	PCM	DTS

Input signal display

• DOLBY DIGITAL

SIGNAL

DIGITAL

One of these lights, depending on the input signal.

DIGITAL ANALOG

DIGITAL

DIGITAL

ANALOG

• DTS

SIGNAL

DIGITAL

• PCM

SIGNAL

DIGITAL

The DIGITAL indicator lights when digital signals are being input

properly. If the DIGITAL indicator does not light, check whether the digital input component setup (page 21) and connections are correct and whether the component’s power is turned on.

NOTE:

•The DIGITAL indicator will light when playing CD-ROMs containing data other than audio signals, but no sound will be heard.

After starting playback

[1] Adjusting the sound quality (tone)

1	The tone switches as follows each time TONE CONTROL is
	pressed.
	BASS	TREBLE

B

(Main unit)

2	With the name of the volume to be			3	2 1
	adjusted selected, turn SELECT knob to	SELECT
	adjust the level.
		3		If you do not want the bass and treble to be adjusted, turn on
	• To increase the bass or treble: Turn
				the tone defeat mode.
	the control clockwise. (The bass or	(Main unit)

	treble sound can be increased to up		The signals do not pass through the
	to +12 dB in steps of 2 dB.)
			bass and treble adjustment circuits,
	• To decrease the bass or treble: Turn the control
			providing higher quality sound.
	counterclockwise. (The bass or treble sound can be
	decreased to up to –12 dB in steps of 2 dB.)		(Main unit)

27

ENGLISH

[2] Listening over headphones

1	Connect the headphones to the	PHONES

PHONES jack of the front panel.

1

2	Press SPEAKER A or B to turn the
	speaker off.

Cautions:

•No sound is produced from the headphones when speakers A or B are turned on.

•When an external power amplifier is connected to the front preout jacks, turn off the external power amplifier’s speaker switch.

[3] Turning the sound off temporarily (muting)

	1	Use this to turn off the audio output	MUTING
		temporarily.
		Press MUTING.

Cancelling MUTING mode. Press the MUTING button again.

Muting mode will also be cancelled when MASTER VOL is adjusted up or down.

[4] Combining the currently playing sound with the desired image

1	Simulcast playback
	Use this switch to monitor a	VIDEO SELECT
	video source other than the
	audio source.
	Press VIDEO SELECT
	repeatedly until the desired	(Remote control unit)
	(Main unit)

source appears on the display.

Cancelling simulcast playback.

•Select “SOURCE” using the video select button.

•Switch the program source to the component connected to the video input.

[5]Checking the currently playing program source, etc.

1	Front panel display
	•	Descriptions of the unit’s
		operations are also		STATUS
		displayed on the front
		panel display. In addition,		DISPLAY
		the display can be
		switched to check the	(Main unit)	(Remote control unit)
		unit’s operating status
		while playing a source by
		pressing STATUS.
2	Using the dimmer function
	•	Use this to change the brightness of the
		display.
		The display brightness changes in four
		steps (bright, medium, dim and off) by
		pressing the main unit’s DIMMER		(Main unit)
		repeatedly.

The brightness changes in 3 steps each time the button is pressed, and finally the display turns off.

NOTE:

To prevent hearing loss, do not raise the volume level excessively when using headphones.

B

2

SYSTEM	SURROUND
SET UP	MENU	MASTER
CH SELECT		VOL
SELECT
T.TONE	STATUS	MUTING	1
RETURN	DISPLAY

	3	2	0
1	VIDEO SELECT CD·MD/CDR·DVD/VDP DISC SKIP+
	TITLE
	8	3	9
	6	2	7

1

SET UP	MENU	MASTER
CH SELECT		VOL
SELECT
T.TONE	STATUS	MUTING
RETURN	DISPLAY	1

CHANNEL TV VOLUME

2 1

28

ENGLISH

Playback using the external input (EXT. IN) jacks

1	Set the external input (EXT.
	IN) mode.
	Press the EXT. IN to switch
	the external input.

(Main unit)

(Remote control unit)

Once this is selected, the input signals connected to the FL (front left), FR (front right), C (center), SL (surround left), and SR (surround right) channels of the EXT. IN jacks are output directly to the front (left and right), center, surround (left and right) speaker systems without passing through the surround circuitry.

In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SUBWOOFER jack.

2	Cancelling the external input mode
	To cancel the external input (EXT. IN) setting, press the INPUT
	MODE (AUTO, PCM, DTS) or ANALOG button to switch to
	the desired input mode. (See page 26.)

B

2	1
	V. AUX	VCR-1	VCR-2	TV/DBS
	4	5	6	7
1, 2	INPUT MODE	CDR / TAPE	TUNER	SHIFT
	8	9	0
	SURROUND	TAPE·VCR
	MODE
		6	7

CHANNEL

(Main unit)	(Remote control unit)

•When the input mode is set to the external input (EXT. IN), the play mode (STEREO, DOLBY/DTS SURROUND, 5CH STEREO or DSP SIMULATION) cannot be set.

NOTES:

•In play modes other than the external input mode, the signals connected to these jacks cannot be played. In addition, signals cannot be output from channels not connected to the input jacks.

•The external input mode can be set for any input source. To watch video while listening to sound, select the input source to which the video signal is connected, then set this mode.

Recording the program source (recording the source currently being monitored)

1	Follow step 1 to 3 under “Playing the input source” (page 26,		2		Start recording on the tape or video deck.
	27).				For instructions, refer to the component’s operating
					instructions.

Simultaneous recording

The signals of the source selected with the function selector button are output simultaneously to the CDR/TAPE and VCR REC OUT jacks. If a total of two tape and/or video decks are connected and set to the recording mode, the same source can be recorded simultaneously on every decks.

NOTES:

•The AUDIO IN’s signal selected with the function selector button are output to the CDR/TAPE and VCR AUDIO OUT jacks.

•The DIGITAL IN’s signal selected with the function selector button are output to the DIGITAL OUT (OPTICAL) jack.

29