Delta Electronics DVP-SX User Manual

Warning

This Instruction Sheet only provides descriptions for electrical specifications, general specifications, installation & wiring, troubleshooting and peripherals. Other detail information about programming and commands is compatible with SA/SC/SX series; please see PLC Application Manual. For more information about the optional peripheral, please see individual product manual.

This is an OPEN TYPE PLC. The PLC should be kept in an enclosure away from airborne dust, humidity, electric shock risk and vibration. Also, it is equipped with protective methods such as some special tools or keys to open the enclosure, so as to avoid the hazard to users and the damage to the PLC.

Never connect the AC main circuit power supply to any of the input/output terminals, as it will damage the PLC.

Check all the wiring prior to power up. To avoid any electromagnetic noise, make sure the PLC is properly grounded . DO NOT touch terminals when power on.

Introduction

Thank you for choosing DELTA’s PLC DVP series. The DVP-SX series is a 10-point (4DI+2DO+2AI+2AO)

special main processing unit. Besides the same commands and functions as DVP-SA/SX/SC series, 2-CH

12-bit analog voltage/current input and 2-CH 12-bit analog voltage/current output are all bipolar. There is

built-in 2-digit 7-segment display corresponds to internal register directly to display PLC station or

user-defined code.

Product Profile and Outline

Units: mm

Battery replacement: Please change the battery within 3 minutes, or the internal data of the PLC (including the program area, RTC and latched registers) could be lost or destroyed.

1Status indicator: POWER, RUN, ERROR, BAT.LOW

2RUN/STOP switch

3 2-digital 7-segment display

4 Digital I/O terminal

5DIN rail clip

6 Analog I/O terminals

7I/O point indicators

8 COM1 (RS-232) (Rx) indicator

9COM2 (RS-485) (Tx) indicator

10

COM1 (RS-232)

Communication port (Slave)

11Nameplate

12Expansion port

13Mounting hold of the expansion unit

14DIN rail (35mm)

15Expansion unit clip

16

COM2 (RS-485)

Communication port 17 DC Power input

18

2 pin removable terminal (standard accessory)

19

Power input cable (standard accessory)

20Battery Cover

21Battery socket connection

22Battery mount

Electrical Specifications

Electrical Specifications

	Model	DVP10SX11R/T	DVP08SM11N	DVP08SN11R/T		DVP08SP11R/T		DVP16SP11R/T
	Item
		MPU: 24V DC (-15% ~ 20%) (with DC input reverse polarity protection),
	Power supply voltage
		Expansion Unit: supplied by the MPU
	Fuse	2A / 250V AC			-
	Power Consumption	5W	1W	1.5W		1.5W		2W
	InsulationResistance	> 5 M at 500 V DC (Between all inputs / outputs and earth)
		ESD: 8KV Air Discharge
	Noise Immunity	EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
		Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV
		RS: 26MHz~1GHz, 10V/m
	Grounding	The diameter of grounding wire cannot be smaller than the wire diameter of terminals L and N
		(All DVP units should be grounded directly to the ground pole).
		Operation: 0°C ~ 55°C (temperature), 50 ~ 95% (humidity), Pollution degree 2;
	Environment	Storage: -25°C ~ 70°C (temperature), 5 ~ 95% (humidity); D/A output operation: 0°C ~ 50°C
		(temperature)
	Vibration / Shock	Standard: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
	Resistance
	Weight (approx.) (g)	138 / 133	64	88 / 68		90 / 70		96 / 76
	Approvals

Electrical Specification of Input Point

Electrical Specification of Output Point

Input Type

DC (SINK or SOURCE)

Output Type

Relay-R

Transistor-T

Current

1.5A/1 point

0.3A/1 point @ 40°C; When the output of Y0

Input Current

24V DC 5mA

and Y1 is high-speed pulse, Y0 and Y1 =

Specification

(5A/COM)

30mA

Off

On,

Voltage

Below 250V

→

30V DC

X0,X1: above 18.5V DC

Specification

AC, 30V DC

Active Level

X2,X3: above 16.5V DC

On Off,

75VA

When the output of Y0 and

→

(Inductive)

X0~X3 below 8V DC

Maximum

9W/1 point

Y1 is high-speed pulse, Y0

Ω

Loading

90 W

and Y1 = 0.9W (Y0 = 32kHz,

About 10ms (An

(Resistive)

Y1 = 10kHz)

Responding

adjustment range of 0 ~ 20

Time

ms could be selected

Responding

About 10 ms

Off

On 20us

Y0 and Y1 are specified

through D1020 and D1021)

Time

On→Off 30us

points for high-speed pulse

Model Name & I/O Configuration

Input

Output

Model

Power

Point

Type

Point

Type

DI

AI

DI

AI

DO

AO

DO

AO

DVP10SX11R

24V

4

2

-20 ~ 20mA

2

2

Relay

-20 ~ 20mA

DC

DC24V/5 mA

range(-1,000 ~ +1,000)

(range:-2,000 ~ +2,000)

DVP10SX11T

+20%

4

2

Sink or Source

-10 ~ +10V

2

2

Resistor

-10 ~ +10V

-15%

range(-2,000 ~ +2,000)

(range:-2,000 ~ +2,000)

Installation & Wiring

3.1 PLC Mounting Arrangements and Wiring Notes

Installation of the DIN rail:

The DVP-PLC can be secured to a cabinet by using the

DIN rail that is 35mm high with a depth of 7.5mm. When

mounting the PLC on the DIN rail, be sure to use the

end bracket to stop any side-to-side motion of the PLC,

thus to reduce the chance of the wires being pulled

loose. At the bottom of the PLC is a small retaining clip.

To secure the PLC to the DIN rail, place it onto the rail

and gently push up the clip. To remove it, pull down the

retaining clip and gently pull the PLC away from the DIN

rail. As shown on the right:

When installing the DVP series PLC, make sure that it is installed in an enclosure with sufficient space (as shown below) to its surroundings so as to allow heat dissipation.

	D
D	DV P	D
	M P
	D

D > 50 mm

Wiring:

		1.		Please use 22-16AWG (1.5mm) wiring (either single or multiple core) for
			22-16AWG	I/O wiring terminals. The specification for the terminals is as shown on
				the left. PLC terminal screws should be tightened to between 1.95
				kg-cm (1.7 in-lbs). Use 60/75°C copper conductor only.
< 1.5mm		2.		I/O signal wires or power supply should not run through the same
				multi-wire cable or conduit.

3.2 Wiring Notes

Power Input Wiring

DVP-SX series input power supply is DC input. Please take a note of listed items when operating DVP-SX. Series.

1.Please make sure the power is at terminals 24V DC and 0V (power range is 20.4V DC ~ 28.8V DC). When voltage is lower than 20.4V DC, PLC will stop operating, all outputs will turn Off and ERROR LED will flash continuously.

2.If the power-off time is less than 10ms, the PLC still operates unaffectedly. If the power-off time is too long or the power voltage drops, the PLC will stop operating and all the outputs will be Off. Once the power is restored, the PLC will return to operate automatically. (There are latched auxiliary relays and registers inside of the PLC, please be aware when programming.)

20.4V~28.8V
24VDC OV	S/ S	X0	X1	X2
DC Input Type
2A
DC /DC	5V

Safety Wiring

Since the PLC is in control of numerous devices, motion of either one device could affect the motion of other

devices, therefore the breakdown of either one device would consequently be detrimental to the whole auto control system, and danger will thus be resulted. Please use the recommended wiring below for the power input:

Power supply for AC loads

5		MC		Power Circuit Protection Fuse (3A)
		1		Power On pilot indicator
4
				Emergency stop
8				The machinery must provide a quick manual method
G uard		2
				disconnecting all system power.
Limit
				Circuit isolation device (System Power Disconnect)
MC	3	MC		Utilize the electromagnetic contactor and the relay to be the
		1		isolation unit of the power circuit to prevent the possible
				instability of the system when the power is supplied on and off.
			DVP PLC MPU (main processing unit)
L N				Grounding
6		7		Power supply:
			AC: 100 ~ 240V AC, 50/60Hz
				DC: 24V DC

Input Point Wiring

The input signal of the input point is the DC power DC input. There are two modes of DC type wiring: SINK and SOURCE, defined as follows:

Sink = Current flows into the common terminal S/S	Source = Current flows out of common terminal S/S
S/S		X0
Sinkin g
X0		S/S
		So urc ing
Loop Equivalent Circuit of Input Point		Wiring Loop

	+24V
		2 4VDC
	24G
DC Type		SINK
(DC Signal IN)
		+5V
	S/S	+24V	OV	S/S	X0 X1	X2
	X0	24VDC
					Sink Type
SINK Mode
	Loop Equivalent Circuit of Input Point			Wiring Loop
	+24 V
DC Type	24 G
(DC Signal IN)		+5V
		SO UR CE
	S/ S	+24V	OV	S/ S	X0 X1	X2
	X0	24VD C
					Source Type
SOURCE Mode

Output Point Wiring
DVP-**-* *-11-R
	L O AD		1. There are two kinds of DVP-SX Series PLC output
	Y0		modules: Relay and Transistor. For relevant electrical
LED	RY	P OW E R	specification, please refer to the function specification.
	C0		2. Be careful with the connection of the common
			terminals when wiring outputs. For example, when
	R E LAY O UT P U T		wiring DVP12SX11R, output terminal Y0 uses one
			common terminal C0, Y1 uses C1, as shown below:
DVP- **-**-11-T
		LOAD
	T	Y0	C0 Y 0 C1 Y 1
LED
	R	< 0 . 3 A	Action indication: When the output point is active, the
	G	C 0	corresponding indicator at the front will be on.
			3. Isolated circuit: The optical coupler is used to isolate
	TRANSISTOR OUTPUT		signals between PLC internal circuits and input
			modules.

Analog Input/Output Point Wiring

Voltage input		CH0		100K
-10V~+10V			V+		CH0
				250
	*3		I+		100K
			COM
Shielded*1
				AG
Current input	CH1			100K	CH1
-20mA~+20mA
	*2		V+	250
			I+		100K
			COM
Shielded*1				AG

voltage output

*5

-10V~+10V

CH0

V+

CH0

I+

AC drive, recorder,

COM

shielding cable *1

scale valve...

current output

CH1

-20mA~20mA

V+

CH1

I+

COM

AC drive, recorder,

shielding cable *4

scale valve...

terminal of

power module

+15V

DC24V

24+

DC/DC

AG

24-

converter

-15V

class 3 grounding

(100

or less)

Note 1:

Please isolate analog input and other power wiring.

Note 2:

If input signal is in current, please short out between V+ and I+ terminals.

Note 3:

If the noise interference from loaded input wiring terminal is significant, please connect a capacitor with 0.1 ~ 0.47µF 25V for noise filtering.

Note 4:

Please isolate analog output and other power wiring.

Note 5:

If the noise interference from loaded input wiring terminal is significant, please connect a capacitor with 0.1 ~ 0.47µF 25V for noise filtering.

Note 6:

Please connect power module terminal and analog output module terminal to system earth point and make system earth point be grounded or connects to machine cover.

Warning:

DO NOT wire to the No function terminal

SA/SX/SC PLC

OPEN TYPE

/

:

/

DVP

DVP-SX

10

4DI+2DO+2AI+2AO

SA/SX/SC

2CH

12-bit

/

2CH

12-bit

/

/

2

1

2

RUN/STOP

3

2

4

I/O

5

DIN

6

I/O

7

/

COM1 (RS-232)

8

(Rx)

9

COM2 (RS-485)

(Tx)

mm

COM1 (RS-232)

10

(Slave)

11

DIN (35mm)

12

13

3

PLC

14

15

16

COM2 (RS-485)

(Master/Slave)

17

18

2 pin

19

20

21

22

DVP10SX11R/T

DVP08SM11N

DVP08SN11R/T

DVP08SP11R/T

DVP16SP11R/T

24V DC

-15% ~ 20%

-

2A/250V AC

5W

1W

1.5W

1.5W

2W

5M

/

500V DC

ESD: 8KV Air Discharge

EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V

Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV

RS: 26MHz ~ 1GHz, 10V/m

L,N

PLC

/

0°C ~ 55°C

50 ~ 95%

2

-25°C ~ 70°C

5 ~ 95%

D/A

0°C ~ 50°C

/

IEC61131-2, IEC68-2-6 (TEST Fc)/IEC61131-2 & IEC68-2-27 (TEST Ea)

, g

138 / 133

64

88 / 68

90 / 70

96 / 76

SINK

SOURCE

-R

-T

24V DC 5mA

1.5A/1

5A/COM

0.3A/1

@ 40°C

, Y0

Y1

30mA

Off → On,

X0

X1

18.5V DC

250V AC,30V DC

30V DC

X2

X3

16.5V DC

On

→ Off,

75VA

X0~X3

8V DC

9W/1

Y0 Y1 0.9W

90W

Y0

50KHz

Y1

10KHz

10ms

D1020 D1021

0 ~ 20ms

10 ms

Off → On 20us

Y0

Y1

On → Off 30us

I/O

DI

AI

DO

AO

DI

AI

DO AO

-20 ~ 20mA

-20 ~ 20mA

DVP10SX11R

24VDC

4

2

2

2

DC24V/5 mA

(

-1,000 ~ +1,000)

(

-2,000 ~ +2,000)

+20%

Sink

Source

-10 ~ +10V

-10 ~ +10V

-15%

DVP10SX11T

4

2

(

-2,000 ~ +2,000)

2

2

(

-2,000 ~ +2,000)