Delta Electronics DOP-EXIO28RAE, DOP-EXIO14RAE User Manual

http://www.delta.com.tw/industrialautomation/

Extension Digital I/O Module

Instruction Sheet

Warning

3Please read this instruction carefully before use.

3DOP series Extension Digital I/O Module should be used with DOP-AE series HMI product. Ensure to switch off the power before wiring.

3Please install this DOP series Extension Digital I/O Module in an enclosure free of airborne dust, humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required for opening the enclosure) in case danger and damage on the device may occur.

3DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check all the wiring again before switching on the power.

3DO NOT touch any internal circuit in 1 minute after the power is switched off. Do NOT touch any terminal when the power is switched on.

3Make sure the ground terminal is correctly grounded in order to prevent electromagnetic interference.

3DO NOT place any heavy objects on the connection port of DOP series Extension Digital I/O Module. Doing so may damage the product.

X Introduction

1.1 Model Explanation

	DOP		-	EXIO		14		R	AE
(1)				(2)		(3)		(4)	(5)
	(1)	Product Name					DOP: Delta Operation Panel
	(2)	Series					EXIO: Extension Digital I/O
	(3)	Input / Output Point					14: 8 input points / 6 output points
							28: 16 input points / 12 output points
	(4)	Output Contact Type					R: Relay
	(5) Applicable HMI Series						AE: DOP-AE Series HMI

1.2 Product Outline

3

1

4

2

1.Connection Port

2.Direct Mounting Hole

3.Input / Output Terminals

4.Nameplate

1.3 Model Name

Model Name			Input / Output
	Power	Input Unit		Output Unit
		Point	Type	Point	Type
DOP-EXIO14RAE		8	DC Type	6	Relay

Sink or

DOP-EXIO28RAE

5VDC,

16

12

Relay

Source

supplied

by HMI

Y Function Specifications

Item

Specifications

Remark

Control Method

Stored program, cyclic scan system

-

I/O Processing Method

Batch I/O (refresh)

Immediate refresh command available

only with I/O of the MPU

Execution Speed

Basic command (average approx. 30

Application command (30 ~ hundreds

us)

us)

Program Language

Commands + Ladder Diagram +

Step commands included

SFC

Item					Specifications		Remark
Program Capacity					999 Steps		Built-in EEPROM
Commands					Basic commands: 32 (including the		Application commands: 59
					STL commands)
Step Relay			General		128 Points		S10 ~ S127
(Latched)			Step Point
Auxiliary			General		1280 Points		M0 ~ M511, M768 ~ M999, 744 points;
							M1000 ~ M1279, 280 points*1
Relay			Latched		256 Points		M512 ~ M767
Timer			Digital		64 Points		T0~T63 (100 ms time base)
					63 Points		T64~T126 (10 ms time base)
					1 Points		T127 (1 ms time base)
			General		112 Points		C0 ~ C111
Counter			Latched		16 Points		C112 ~ C127
							C235,C236,C237,C238,C241,C242,
			32bit		13 Points		C244,C246,C247,C249,C251,C252,
							C254 (all of them are latched type)
Data Register			General		408 Points		D0 ~ D407
			Latched		192 Points		D408 ~ D599
Pointer			P		64 Points		P0 ~ P63
Index			E / F		2		E, F
Register
Constant			Decimal K		16bit: -32768 ~ +32767		32bit: -2147483648 ~ [phone]
			Hexadecim		16bit: 0000 ~ FFFF		32bit: 00000000 ~ FFFFFFFF
			al H
Self Diagnosis / Protection					I/O check, system execution timeout check, invalid command check, program
					check and password settings
Monitor / Debug					Program execution time display, bit / word, device settings

*1: M1000, M1001, M1002, M1003, M1020, M1021, M1022, M1067, M10068, and M1161 are the special auxiliary relays (special M).

Z Electrical Specifications

Item / Model Name		DOP-EXIO14RAE			DOP-EXIO28RAE
Power Supply Voltage		5VDC, 1A (supplied by HMI)
Power Consumption		0.25W			0.5W
		RS: Frequency: 80MHz ~ 1GHz,			1.4GHz ~ 2.0GHz, Test level 10V/m
		CS: Frequency: 0.15MHz ~ 80MHz, Test level 10V (HMI power port & I/O line)
Noise Immunity		ESD: Air discharge ±8KV
		EFT: ±1.5KV (HMI power port)
			±1KV (I/O line)
		Surge: ±2KV (HMI power port)
Ambient Temperature /		Operation: 0°C ~ 50°C (Temperature), 10 ~ 90% (Humidity),
Humidity		Storage: -40°C ~ 85°C (Temperature), 10 ~ 90% (Humidity)
			IEC 61131-2 Compliant
Vibration / Shock		5Hz f 9Hz = Continuous: 1.75mm / Occasional: 3.5mm
		9Hz f 150Hz = Continuous: 0.5g / Occasional: 1.0g
		X, Y, Z directions for 10 times
Weight		Approx. 95.5g			Approx. 116g

		Input Point Electric Specifications
Input Type		DC (SINK or SOURCE)
Input Voltage		24VDC (5mA)
Active Level		Off→On, above 16VDC
		On→Off, below 14.4VDC
Response Time		Approx. 10ms

		Output Point Electric Specifications
Output Type		Relay-R
Current Specifications		1.5A / 1 Point (5A/COM)
Voltage Specifications		250VAC, below 30VDC
Maximum Loading		75VA (Inductive)
		90 W (Resistive)
Response Time		Approx. 10 ms
Mechanical Life		2 × 107 times (without load)
Electrical Life		100,000 times (3A 250VAC/30VDC)
		6,000 times (5A 250VAC/30VDC)
[ Installation & Wiring

4.1 Wiring

2

1.Please use the 28-16 AWG (1.5mm ) single-core bare wire (Solid type) or the multi-core wire (Stranded type) for the I/O wiring. The stripped length of

			22-16AWG	the wire should be 6-7mm, and the torque specification of the screw for the
				terminal is 4.5lb-in. Please refer to the specifications of the terminal shown
				in the figure on the left.
< 1.5mm

2.DO NOT place the I/O signal wires and power supply wire in the same wiring duct.

4.2 Caution

Environment

1.DO NOT install the Extension Digital I/O Module in a place subjected to corrosive or flammable gases, liquids, or airborne dust or metallic particles.

2.DO NOT install the Extension Digital I/O Module in a location high temperature and high humidity (where temperature and humidity will exceed specification).

3.DO NOT install the Extension Digital I/O Module in a location where vibration and shock will exceed specification.

Wiring Note

1.Please avoid any conductive debris and tiny metal materials enter the Extension Digital I/O Module when screwing and wiring.

2.Allow a minimum space of 50mm between the Extension Digital I/O Module and other control devices, and keep the Extension Digital I/O Module away from the high-voltage lines or any power equipment.

4.3 Terminal Identification

4.4Wiring

There are two types of DC inputs, SINK and SOURCE, and they are defined as follows:

Sink = (common port for current input S/S)

Source = (common port for current output S/S)

Input Point Wiring (S/S shown in the wiring diagrams indicates SS1 or SS2 contact)

DC Signal IN

Input point loop equivalent circuit

Wiring loop

SINK mode

DC Signal IN

Input point loop equivalent circuit

Wiring loop

SOURCE mode

Output Point Wiring

Be careful with the connection of the common terminals
when wiring outputs. For example, when wiring
DOP-EXIO14RAE (DOP-EXIO28RAE), output terminal
Y0	(Y10) uses C0 (C10), Y1 (Y11) uses C1 (C11), Y2 ~
Y3	(Y12 ~ Y13) uses C3 (C13), Y4 ~ Y5 (Y14 ~ Y15)
uses C5 (C15), as shown below:

NOTE

1)The content of this instruction sheet may be revised without prior notice. Please consult our distributors or download the most updated version at http://www.delta.com.tw/industrialautomation.