Dell 0476T, 8376T, 2476T, 4476T, 1476T User Manual

...
0 (0)
®
Dell® Model UltraScan P991 Color Monitor Quick Setup
Safety Instructions
Observe the following safety guidelines when connecting and using your monitor:
•Be sure your monitor is electrically rated to operate with the AC power available in your location.
•Locate your monitor near an easily accessible electrical outlet.
•Place the monitor on a solid surface and treat it carefully. The screen can be damaged if dropped, sharply hit, or touched with a sharp or abrasive implement.
•Put your monitor in a location with low humidity and a minimum of dust.
•Never use your monitor if the power cable has been damaged. Do not allow anything to rest on the power cable, and keep the cable away from where people could trip over it.
•Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock.
•Be sure to hold the plug, not the cable, when disconnecting the monitor from an electrical outlet.
•Openings in the monitor cabinet are provided for ventilation. To prevent overheating, these openings should not be blocked or covered. Also, avoid using the monitor on a bed, sofa, rug, or other soft surface. Doing so may block the ventilation openings in the bottom of the cabinet. If you put the monitor in a bookcase or some other enclosed space, be sure to provide adequate ventilation.
•Do not expose the monitor to rain or use it near water. If the monitor accidentally gets wet, unplug it and contact an authorized dealer immediately. You can clean the exterior of the monitor with a damp cloth when necessary, but be sure to unplug the monitor first.
•If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or ser­vice center.
Connecting Your Monitor to a Computer
1. Turn off your computer and unplug the computer power cable.
2. Connect the blue connector of the monitor’s signal cable to the blue video connector on the back of your computer. Tighten the connector screws finger tight. Do not
overtighten.
3. Fully insert the monitor power cable into the power port on the back of the monitor.
4. Plug the power cables of your computer and your monitor into a nearby electrical outlet.
5. Turn on your computer and monitor. If the monitor does not display an image, refer to the troubleshooting section of this guide.
Driver Installation
Use the monitor CD to install the appropriate monitor driver for your operating system.
Microsoft Windows
Windows 98 automatically detects the new monitor and dis plays the
Hardware Wizard
1. Insert the monitor CD in the CD-ROM drive, and click
New Hardware Wizard
2. Click the
3. Confirm that the driver was found on the CD and click
driver.
4. Click
Finish
To manually install or update the driver, perform the following steps:
1. Click
Start-> Settings-> Control Panel
2. In the
Display P roperties
3. Click the
4. When the
previous paragraph.
Microsoft Windows
First determine the Windows 95 version installed on your computer by right-clicking the
My Computer
listed under
®
98 Operati ng System
dialog box if the monitor driver is not already installed.
dialog box appears.
CD-ROM drive
to exit the add
Monitor
Update Device Driver Wizard
icon on the desktop and selecting
System
box to install the drivers from the CD and then click
New Hardware Wizard
window, clic k the
tab, and then click
®
95 Operati ng System
. Perform the steps for the appropriate version.
and then double click
Settings
Change
dialog box appears, follow the steps in the
next>
Next>
dialog box.
tab, and then click
.
Properties
Add New
twice when the
twice to install the
Display
. The version number is
Add
.
Advanced
Version 4.00.950A
1. Click
Start-> Settings-> Control Panel
2. In the
3. In the
4. Insert the monitor CD in the CD-ROM drive, type d:\ (change the drive letter to
5. In the
.
Next>
6. In the
7. In the
Version 4.00.950B
1. Click
2. In the
.
3. In the
4. In the
5. Insert the monitor CD in the CD-ROM drive, type d:\ (change the drive letter to
6. In the
7. In the
8. In the
Display Properties
Display Type
match your CD-ROM drive if it is not drive D) in the
from
Properties Change
match you CD-ROM drive if it is not drive D) in the box, an d click OK.
.
Change Display Type
: box, and click OK.
Select Device Change Display Type Display Properties
Start-> Settings-> Control Panel
Display Properties
.
Advanced Display Properties
.
Select Device
Select Device Advanced Display Properties Display Properties
window, click the
window, click
window, click the appropriate monitor model and the click OK.
window, click
window, click OK.
window, click the
window, click
window, click the appropriate monitor model and then click OK.
window, click OK.
and then double-click
Settings
Change
.
Close
and then double-cli ck
Settings
window, click the
Have Disk
.
Copy manufacturer’s files from
window, click
tab and the click
and then click
Copy manufacturer’s files
tab and the click
Monitor
Close
Display.
Have Disk
Display
tab and then click
.
Change
.
Advanced
.
:
Loading...
+ 1 hidden pages