Dell SX Systems, SX260, 5X523 User Manual

0 (0)

Dell™ OptiPlex™ SX Systems

Setup and Quick

Reference Guide

Asennusja pikaopas

Installasjonsog hurtigreferanseveiledning

Руководство по установке и краткий справочник

Inštalačná a referenčná príručka

Kratki referenčni in namestitveni priročnik

Handbok för inställningar och snabbreferens

Model DCT

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

Dell™ OptiPlex™ SX Systems

Setup and Quick

Reference Guide

Model DCT

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Abbreviations and Acronyms

For a complete list of abbreviations and acronyms, see the “Glossary” in the

User’s Guide.

If you purchased a Dell™ n Series computer, any references in this document to Microsoft® Windows® operating systems are not applicable.

____________________

Information in this document is subject to change without notice. © 2002–2003 Dell Computer Corporation. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.

Trademarks used in this text: Dell, OptiPlex, and the DELL logo are trademarks of Dell Computer Corporation; Microsoft, MS-DOS, Windows NT, and Windows are registered trademarks of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.

July 2003

P/N 5X523

Rev. A03

Contents

About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . .

5

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5

CAUTION: Safety Instructions . . . . . . . . . . . . . . . . . . .

7

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7

When Using Your Computer . . . . . . . . . . . . . . . . . . . .

9

When Working Inside Your Computer . . . . . . . . . . . . . .

10

Protecting Against Electrostatic Discharge . . . . . . . . . . .

11

Battery Disposal . . . . . . . . . . . . . . . . . . . . . . . .

11

Getting Started/Setup . . . . . . . . . . . . . . . . . . . . . . .

12

Determine the Computer’s Placement and Orientation . . . . . .

12

Installing a Device in the Module Bay . . . . . . . . . . . . . .

13

Attaching the Stand . . . . . . . . . . . . . . . . . . . . . . .

14

Connecting the AC Adapter . . . . . . . . . . . . . . . . . . .

15

Connecting External Devices . . . . . . . . . . . . . . . . . .

16

Attaching the Cable Cover . . . . . . . . . . . . . . . . . . . .

17

Attaching the Stand to the Mounting Plate . . . . . . . . . . .

19

Finding Information and Assistance . . . . . . . . . . . . . . . .

21

Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . .

22

Troubleshooting Tools . . . . . . . . . . . . . . . . . . . . . .

23

Using the Dell Drivers and Utilities CD . . . . . . . . . . . . .

23

Running the Dell Diagnostics . . . . . . . . . . . . . . . . . .

24

Running the Dell IDE Hard-Drive Diagnostics . . . . . . . . . .

25

Regulatory Information . . . . . . . . . . . . . . . . . . . . . . .

26

Contents 3

4 Contents

About This Guide

This document contains getting started/setup; solving problems; and safety, regulatory, and warranty information about your DellOptiPlex™ computer.

To obtain the latest versions of the documents on your hard drive, go to the Dell Support website at support.dell.com.

Regulatory Model Number

and Chassis Type

DCT = Ultra small formfactor (USF) computer

Features

Two USB slots, headphone

 

 

mounting slot

and microphone connectors

 

 

(insert stand for

 

 

 

 

 

vertical position)

 

 

power button

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mounting slot (insert stand for hanging horizontal position)

mounting slot (insert stand for hanging vertical position)

 

 

 

 

 

 

 

 

module release

module bay

button

 

 

 

diagnostic LEDs

computer cover/hard-drive cover release button

Setup and Quick Reference Guide

5

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

 

 

 

 

 

 

 

 

 

 

cable cover

 

 

hard-drive cover (open

 

module bay

computer cover

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

cover to access module

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

device locking switch)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

power adapter

chassis-stand

computer

 

mounting plate

stand

6 Setup and Quick Reference Guide

CAUTION: Safety Instructions

Use the following safety guidelines to help ensure your own personal safety and to help protect your computer and working environment from potential damage.

General

Do not attempt to service the computer yourself unless you are a trained service technician. Always follow installation instructions closely.

To help prevent electric shock, plug the computer and device power cables into properly grounded electrical outlets. These cables are equipped with 3-prong plugs to help ensure proper grounding. Do not use adapter plugs or remove the grounding prong from a cable. If you must use an extension cable, use a 3-wire cable with properly grounded plugs.

To help avoid the potential hazard of electric shock, do not use your computer during an electrical storm.

To help avoid the potential hazard of electric shock, do not connect or disconnect any cables or perform maintenance or reconfiguration of this product during an electrical storm.

If your computer includes a modem, the cable used with the modem should be manufactured with a minimum wire size of 26 American wire gauge (AWG) and an FCC-compliant RJ-11 modular plug.

Before you clean your computer, disconnect the computer from the electrical outlet. Clean your computer with a soft cloth dampened with water. Do not use liquid or aerosol cleaners, which may contain flammable substances.

To help avoid possible damage to the system board, wait 5 seconds after turning off the computer before disconnecting a device from the computer.

Setup and Quick Reference Guide

7

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

CAUTION: Safety Instructions (continued)

To avoid shorting out your computer when disconnecting a network cable, first unplug the cable from the network adapter on the back of your computer, and then from the network jack. When reconnecting a network cable to your computer, first plug the cable into the network jack, and then into the network adapter.

To help protect your computer from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).

Ensure that nothing rests on your computer’s cables and that the cables are not located where they can be stepped on or tripped over.

Do not push any objects into the openings of your computer. Doing so can cause fire or electric shock by shorting out interior components.

Keep your computer away from radiators and heat sources. Also, do not block cooling vents. Avoid placing loose papers underneath your computer; do not place your computer in a closed-in wall unit or on a bed, sofa, or rug.

Do not spill food or liquids on your computer.

Do not use your computer during an electrical storm unless the AC adapter cable has been disconnected from the electrical outlet.

When you use the AC adapter to run the computer, place the AC adapter in a ventilated area, such as a desk top or on the floor.

The AC adapter may become hot during normal operation of your computer. Use care when handling the adapter during or immediately after operation.

8 Setup and Quick Reference Guide

When Using Your Computer

As you use your computer, observe the following safe-handling guidelines.

CAUTION: Do not operate your computer with any cover(s) (including computer covers, bezels, filler brackets, front-panel inserts, and so on) removed.

Your computer is equipped with one of the following:

A fixed-voltage power supply — Computers with a fixed-voltage power supply do not have a voltage selection switch on the back panel and operate at only one voltage (see the regulatory label on the outside of the computer for its operating voltage).

An auto-sensing voltage circuit — Computers with an auto-sensing voltage circuit do not have a voltage selection switch on the back panel and automatically detect the correct operating voltage.

A manual voltage selection switch — Computers with a voltage selection switch on the back panel must be manually set to operate at the correct operating voltage.

Set the switch to the position that most closely matches the voltage used in your location.

NOTICE: To help avoid damaging a computer with a manual voltage selection switch, set the switch for the voltage that most closely matches the AC power available in your location. For Japan, the voltage selection switch must be set to the 115-V position even though the AC power available in Japan is 100 V. Also, ensure that your monitor and attached devices are electrically rated to operate with the AC power available in your location.

Before working inside the computer, unplug the computer to help prevent electric shock or system board damage. Certain system board components continue to receive power any time the computer is connected to AC power.

Setup and Quick Reference Guide

9

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

When Using Your Computer (continued)

When Working Inside Your Computer

Before you open the computer cover, perform the following steps in the sequence indicated.

CAUTION: Do not attempt to service the computer yourself, except as explained in your online Dell™ documentation or in instructions otherwise provided to you by Dell. Always follow installation and service instructions closely.

NOTICE: To help avoid possible damage to the system board, wait 5 seconds after turning off the computer before removing a component from the system board or disconnecting a device from the computer.

1Perform an orderly computer shutdown using the operating system menu.

2Turn off your computer and any devices connected to the computer.

3Ground yourself by touching an unpainted metal surface on the chassis, such as the metal at the back of the computer, before touching anything inside your computer.

While you work, periodically touch an unpainted metal surface on the computer chassis to dissipate any static electricity that might harm internal components.

4Disconnect your computer and devices, including the monitor, from their electrical outlets. Also, disconnect any telephone or telecommunication lines from the computer.

Doing so reduces the potential for personal injury or shock.

In addition, take note of these safety guidelines when appropriate:

When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before disconnecting the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.

Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a microprocessor chip by its edges, not by its pins.

CAUTION: There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the manufacturer. Do not dispose of the battery along with household waste. Contact your local waste disposal agency for the address of the nearest battery deposit site.

10 Setup and Quick Reference Guide

When Using Your Computer (continued)

Protecting Against Electrostatic Discharge

Static electricity can harm delicate components inside your computer. To prevent static damage, discharge static electricity from your body before you touch any of your computer’s electronic components, such as the microprocessor. You can do so by touching an unpainted metal surface on the computer chassis.

As you continue to work inside the computer, periodically touch an unpainted metal surface to remove any static charge your body may have accumulated.

You can also take the following steps to prevent damage from electrostatic discharge (ESD):

Do not remove components from their antistatic packing material until you are ready to install the component in your computer. Just before unwrapping the antistatic packaging, discharge static electricity from your body.

When transporting an electrostatic sensitive component, first place it in an antistatic container or packaging.

Handle all electrostatic sensitive components in a static-safe area. If possible, use antistatic floor pads and workbench pads.

Battery Disposal

Your computer uses a lithium coin-cell battery. The lithium coin-cell battery is a long-life battery, and it is very possible that you will never need to replace it. However, should you need to replace it, see your

User’s Guide.

Do not dispose of the battery along with household waste. Contact your local waste disposal agency for the address of the nearest battery deposit site.

Setup and Quick Reference Guide

11

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

Getting Started/Setup

CAUTION: Before performing any of the procedures listed below, read and follow the safety instructions on page 7.

NOTICE: Do not turn on your computer until all setup steps are completed.

1

Determine the Computer’s Placement and Orientation

NOTE: If you want to orient your computer vertically or horizontally under a desktop or tabletop, see "Attaching the Stand" on page 14 and "Attaching the Stand to the Mounting Plate" on page 19.

NOTICE: Do not place your monitor on the computer. Use a monitor stand.

NOTICE: In a high-vibration environment, when installing the computer under a desktop or tabletop, use the optional wall-mount bracket instead of the chassis stand. To order this bracket, contact Dell.

NOTICE: To ensure proper ventilation, do not place your computer vertically on a desktop without using the computer stand (see "Attaching the Stand").

NOTICE: To ensure proper ventilation, do not block the cooling vents.

12 Setup and Quick Reference Guide

2 Installing a Device in the Module Bay

NOTE: To locate the module device locking switch, remove the hard-drive cover.

Your Dell computer ships with either a floppy drive or an airbay installed in the module bay. To install a CD, DVD, or second hard drive in the module bay, first remove the airbay and then install the device.

module device locking switch

 

 

 

 

 

 

 

 

 

 

 

13

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Setup and Quick Reference Guide

 

 

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

3

Attaching the Stand

NOTE: If you are installing the computer under a desktop or tabletop, first attach all cables, and then attach the stand to the mounting plate (see "Attaching the Stand to the Mounting Plate" on page 19).

1Raise the captive screw and slide the chassis stand slat into one of three mounting slots on the back of the computer.

2When the stand is in place, tighten the screw.

NOTICE: If your computer is oriented under a desktop or tabletop and is in a high-vibration environment, use the optional wall-mount bracket instead of the computer stand.

14 Setup and Quick Reference Guide

4 Connecting the AC Adapter

NOTE: The power adapter LED will light when the adapter is properly plugged into a wall outlet and into the computer.

1Connect the power adapter to the connector on the back of the computer.

2Connect the power cable to the power adapter.

NOTICE: The following steps apply to Japan only.

CAUTION: If you decide to connect the green ground wire to an electrical outlet, do not permit contact between the green ground wire and power leads because electrical shock, fire, or damage to your computer can occur (see the following figure).

If you decide not to connect the green ground wire to an electrical outlet, go to step 4.

3Connect the metal ground connector to the grounding source on the outlet (see the following figure):

a Loosen the grounding source.

bSlide the metal ground connector behind the grounding source, and then tighten the grounding source.

grounding source

metal ground connector

4 Connect the AC power cable to the outlet.

Setup and Quick Reference Guide

15

Dell SX Systems, SX260, 5X523 User Manual

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

5 Connecting External Devices

NOTE: Connect only one keyboard and one mouse.

CAUTION: To help prevent electric shock, use only the power adapter and power cable provided, and ensure that they are plugged into a properly grounded power source.

SX260 SX270

16 Setup and Quick Reference Guide

Connecting a VGA Monitor

If you have a VGA monitor and a DVI connector on the back of your computer, plug the VGA-DVI adapter into the DVI connector and connect the monitor cable to the adapter as shown.

6 Attaching the Cable Cover

NOTICE: If you are installing the computer under a desktop or tabletop, do not attach the cable cover until the computer is firmly attached to the mounting plate (see Step 7, "Attaching the Stand to the Mounting Plate" on page 19).

NOTICE: If you use the stand on your computer, attach the stand before attaching the cable cover.

NOTICE: When attaching the cable cover, do not place the computer face-down so that the surface comes in contact with a hard surface. Doing so may press the power button and may scratch the face of the computer.

1Attach all of the cables to the back of the computer.

2Hold the bottom piece of the cable cover and align the four tabs with the four slots on the computer’s back panel.

3Insert the tabs into the slots and slide the piece toward the diagnostic lights (see the illustration) until it is securely positioned.

Setup and Quick Reference Guide

17

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

4Grasp the top piece of the cable cover and align the two tabs with the two slots in the computer’s back panel.

5Insert the tabs into the slots and slide the piece toward the diagnostic lights (see the illustration).

6Install a security device in the security cable slot (optional).

security cable slot

Do not place the computer facedown on the bezel

18 Setup and Quick Reference Guide

To remove the cable cover, remove the device installed in the security cable slot, if used.

1Grasp the top piece of the cable cover and slide it to the left until it stops, and then lift it up and away.

2To remove the bottom piece of the cable cover, while pressing the lever, slide the piece to the left until it stops, and then lift it up and away.

7 Attaching the Stand to the Mounting Plate

NOTICE: When installing the computer in the hanging orientation, avoid locations where it will be bumped by a user’s legs or chair.

CAUTION: Attach the mounting plate to a solid surface capable of supporting 40 lbs (18.1 kg) hanging weight.

NOTE: Before attaching the mounting plate to a surface, first orient yourself with how the stand will attach to the mounting plate.

1Using the four #6 wood screws (0.625 inch; 15.88 mm) provided, attach the mounting plate to a solid surface with a minimum thickness of 1 inch (2.5 cm) (see the illustration).

2Orient the computer and stand under the mounting plate approximately 1 inch (2.5 cm) from the edge of the mounting plate.

Setup and Quick Reference Guide

19

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

3Lift the computer and stand, insert the stand into the mounting bracket, and slide the stand until the release-lever tab is inserted through the slot in the mounting plate.

4Attach the cable cover (if used).

mounting-plate slot

release-lever tab

screw holes (4)

solid surface with a 1-inch (2.5 cm) minimum thickness

NOTICE: When completing your computer setup, secure all cables toward the back of your work area to prevent the cables from being pulled, tangled, or stepped on.

8

Turn on the computer, read the software license agreement, and follow the

 

operating system setup instructions on the screen.

 

 

9

Congratulations! You have completed your system setup.

20 Setup and Quick Reference Guide

Finding Information and Assistance

What Are You Looking For?

Find it Here

 

 

• A diagnostic program for my computer

D r i v e r s a n d U t i l i t i e s C D ( a l s o k n o w n a s t h e

• Drivers for my computer

R e s o u r c e C D )

 

• My computer documentation

You can use this CD to access

• My device documentation

documentation, reinstall drivers,

 

or run diagnostics tools.

• Express Service Code and Service Tag

E x p r e s s S e r v i c e C o d e a n d P r o d u c t Ke y

Number

 

 

 

 

 

 

 

 

Located on your computer.

• Microsoft® Windows® License Label

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

How to remove and replace parts

Technical specifications

How to configure system settings

How to troubleshoot and solve problems

U s e r ’ s G u i d e

Depending on your operating system, double-click the User’s Guides icon on your desktop or click the Start button and then click Help and Support to access the electronic documentation stored on your hard drive.

• How to reinstall my operating system

O p e r a t i n g S y s t e m C D

If you reinstall your operating system, use the Drivers and Utilities

CD to reinstall drivers for the devices that came with your computer.

Setup and Quick Reference Guide

21

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

What Are You Looking For?

Find it Here

 

 

• Latest drivers for my computer

D e l l S u p p o r t w e b s i t e

• Answers to technical service and

The Dell Support website provides several online tools, including:

support questions

• Solutions — Troubleshooting tips, Knowledge Base articles

• Online discussions with other users

• Community — Online discussion with other Dell customers

and technical support

• Upgrades — Upgrade information for components, operating

• Documentation for my computer

system, drivers, and information about online classes

 

 

• Customer Care — Contact information, order status, warranty,

 

and repair information

 

• Downloads — Drivers, patches, and software updates

 

• Reference — Computer documentation, product

 

specifications, white papers, and a glossary of computer terms

 

 

• Service call status and support history

D e l l P r e m i e r S u p p o r t w e b s i t e

• Top technical issues for my computer

The Dell Premier Support website is customized for corporate,

• Details on my computer configuration

government, and education customers. This site may not be

 

available in all regions.

 

 

• How to use Windows XP

W i n d o w s X P H e l p a n d S u p p o r t C e n t e r

• Documentation for my computer

1 Click the Start button, and then click Help and Support.

• Documentation for devices

2 Type a word or phrase that describes your problem, and then

(such as a modem)

click the arrow icon.

 

3 Click the topic that describes your problem.

 

4 Follow the instructions shown on the screen.

 

 

Solving Problems

Dell provides a number of tools to help you if your system does not perform as expected. For the latest troubleshooting information available for your system, see the Dell Support website at support.dell.com. You can also find descriptions of Dell troubleshooting tools in the section titled "Getting Help" in your online User’s Guide.

If computer problems occur that require help from Dell, write a detailed description of the error, beep codes, or diagnostics light patterns; record your Express Service Code and Service Tag Number below; and then contact Dell from the same location as your computer.

See "Finding Information and Assistance" on page 21 for an example of the express service code and service tag numbers.

Express Service Code:___________________________

Service Tag Number:___________________________

22 Setup and Quick Reference Guide

Troubleshooting Tools

The Dell Diagnostics tests various components in your computer and helps to identify the cause of computer problems. For more information, see "Running the Dell Diagnostics" on page 24.

The following features can indicate a possible failure and help you troubleshoot a computer problem:

System Lights — Located on the front of the computer.

Diagnostic Lights — Located on the back of the computer.

System Messages — Appear on your monitor screen.

Beep Codes — A series of audible beeps emitted by your computer. See your User’s Guide for more information about these features.

Using the Dell Drivers and Utilities CD

To use the Dell Drivers and Utilities CD while you are running the Microsoft® Windows® operating system, perform the following steps:

NOTE: To access device drivers and user documentation, you must use the Drivers and Utilities CD while you are running Windows.

1Turn on the computer and allow it to boot to the Windows desktop.

2Insert the Dell Drivers and Utilities CD into the CD drive.

If you are using the Drivers and Utilities CD for the first time on this computer, the installation window opens to inform you that the CD is about to begin installation.

3Click OK to continue.

To complete the installation, respond to the prompts offered by the installation program.

4Click Next at the Welcome Dell System Owner screen.

5Choose the appropriate System Model, Operating System, Device Type, and Topic.

Setup and Quick Reference Guide

23

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

Drivers for Your Computer

To display a list of device drivers for your computer, perform the following steps:

1Click My Drivers in the Topic pull-down menu.

The Drivers and Utilities CD scans your computer’s hardware and operating system, and then a list of device drivers for your system configuration is displayed on the screen.

2Click the appropriate driver and follow the instructions to download the driver to your computer.

To view all available drivers for your computer, click Drivers from the Topic pull-down menu.

Running the Dell Diagnostics

The Dell Diagnostics is a program that tests various components in your computer. Run this program whenever you have a computer problem to help you identify the source of the problem. You can run the Dell Diagnostics from your hard drive or the Drivers and Utilities CD.

From the Hard Drive:

NOTICE: If your hard drive fails, run the Dell IDE Hard-Drive Diagnostics (see "Running the Dell IDE Hard-Drive Diagnostics" on page 25).

1Shut down and restart the computer.

2When the DELLlogo appears, press <F12> immediately.

NOTE: If you receive a message stating that no Diagnostics utility partition has been found, follow the instructions to run the Dell Diagnostics from your Drivers and Utilities CD.

If you wait too long and the Windows logo appears, continue to wait until you see the Windows desktop. Then shut down your computer through the Start menu and try again.

3When the boot device list appears, highlight Boot to Utility Partition and press <Enter>.

4When the Dell Diagnostics Main Menu appears, select the test you want to run.

5Close the test screen to return to the Main Menu screen. To exit the Dell Diagnostics and restart the computer, close the Main Menu screen.

24 Setup and Quick Reference Guide

From the Drivers and Utilities CD:

1Insert the Drivers and Utilities CD into the CD drive.

2Shut down and restart the computer.

When the DELL logo appears, press <F12> immediately.

If you wait too long and the Windows logo appears, continue to wait until you see the Windows desktop. Then shut down your computer through the Start menu and try again.

NOTE: This feature changes the boot sequence for one time only. On the next start-up, the computer boots according to the devices specified in system setup.

3When the boot device list appears, highlight IDE CD-ROM Device and press <Enter>.

4Select the IDE CD-ROM Device option from the CD boot menu.

5Select the Boot from CD-ROM option from the menu that appears.

6Type 1 to start the ResourceCD menu.

7Type 2 to start the Dell Diagnostics.

8Select Run the 32 Bit Dell Diagnostics from the numbered list. If multiple versions are listed, select the version appropriate for your platform.

9When the Dell Diagnostics Main Menu appears, select the test you want to run.

10When the tests are completed, remove the CD.

Running the Dell IDE Hard-Drive Diagnostics

The Dell IDE Hard-Drive Diagnostics is a utility that tests the hard drive to troubleshoot or confirm a hard-drive failure.

1Turn on your computer (if your computer is already on, restart it).

2When F2 = Setup appears in the upper-right corner of the screen, press <Ctrl><Alt><D>.

3Follow the instructions on the screen.

If a failure is reported, see "Hard Drive Problems" in your User’s Guide.

Setup and Quick Reference Guide

25

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

Regulatory Information

Electromagnetic Interference (EMI) is any signal or emission, radiated in free space or conducted along power or signal leads, that endangers the functioning of a radio navigation or other safety service or seriously degrades, obstructs, or repeatedly interrupts a licensed radio communications service. Radio communications services include but are not limited to AM/FM commercial broadcast, television, cellular services, radar, air-traffic control, pager, and Personal Communication Services (PCS). These licensed services, along with unintentional radiators such as digital devices, including computer systems, contribute to the electromagnetic environment.

Electromagnetic Compatibility (EMC) is the ability of items of electronic equipment to function properly together in the electronic environment. While this computer system has been designed and determined to be compliant with regulatory agency limits for EMI, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference with radio communications services, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference

by one or more of the following measures:

Reorient the receiving antenna.

Relocate the computer with respect to the receiver.

Move the computer away from the receiver.

Plug the computer into a different outlet so that the computer and the receiver are on different branch circuits.

If necessary, consult a Dell Technical Support representative or an experienced radio/television technician for additional suggestions.

NOTE: Additional regulatory information regarding your system can be found in your

User’s Guide.

26 Setup and Quick Reference Guide

Dell™ OptiPlex™ SX -järjestelmät

Asennusja pikaopas

Malli DCT

w w w . d e l l . c o m | s u p p o r t . e u r o . d e l l . c o m

Huomautukset, varoitukset ja laitteistovaroitukset

HUOMAUTUS: Huomautukset ovat tärkeitä tietoja, joiden avulla voit käyttää tietokonetta entistä paremmin.

LAITTEISTOVAROITUS: Laitteistovaroitukset ovat varoituksia tilanteista, joissa laitteisto voi vahingoittua tai joissa tietoja voidaan menettää. Niissä kerrotaan myös, miten nämä tilanteet voidaan välttää.

VAROITUS: Varoituksissa kerrotaan tilanteista, joihin saattaa liittyä omaisuusvahinkojen, loukkaantumisen tai kuoleman vaara.

Lyhenteet

Lyhenteiden luettelo on käyttöoppaan sanasto-osassa.

Jos ostit Dell™ n Series -tietokoneen, mitkään tässä oppaassa olevat viittaukset Microsoft® Windows® -käyttöjärjestelmiin eivät koske sitä.

____________________

Tämän asiakirjan tiedot voivat muuttua ilman erillistä ilmoitusta.

© 2002 - 2003 Dell Computer Corporation. Kaikki oikeudet pidätetään.

Tämän tekstin kaikenlainen kopioiminen ilman De ll Computer Corporationin kirjallista lupaa on jyrkästi kielletty.

Tekstissä käytetyt tavaramerkit Dell, OptiPlex ja DELL-logo ovat Dell Computer Corporationin tavaramerkkejä. Microsoft, MS-DOS, Windows NT ja Windows ovat Microsoft Corporationin rekisteröityjä tavaramerkkejä.

Muut tekstissä mahdollisesti käytetyt tavaramerkit ja tuotenimet viittaavat joko merkkien ja nimien haltijoihin tai näiden tuotteisiin. Dell Computer Corporation kieltää omistusoikeuden muihin kuin omiin tavaramerkkeihinsä ja tuotenimiinsä.

Elokuu 2003

P/N 5X523

Rev. A03

Loading...
+ 160 hidden pages