Shelleymatic |
|
|
|
|
|
® |
|
|
Project ___________________________________ |
|
|
|
|
|
|
by Del eld |
|
|
Item _____________________________________ |
|
|
|
Quantity _ ________________________________ |
|
|
|
|
|
|
N6/N10/N14 |
|
|
CSI Section 11400 |
|
|
|
Approved _ _______________________________ |
||
|
|
Date _____________________________________ |
||
Free-Standing Self-Contained Milk Or Beverage Dispensers |
|
|
||
|
|
|||
|
|
|
|
|
Models |
|
|
|
|
• N6-1313-34 |
6 crate capacity, 34” height |
• N10-1313-36 |
10 crate capacity, 36” height |
|
• N6-1313-36 |
6 crate capacity, 36” height |
• N14-1313-34 |
14 crate capacity, 34” height |
|
• N10-1313-34 |
10 crate capacity, 34” height |
• N14-1313-36 |
14 crate capacity, 36” height |
N10-1313-36
(shown with optional casters)
Standard Features
•Cabinet top and corners to be 16-gauge stainless steel
•1” IPS drain
•Units insulated with foamed in place environmentally friendly, Kyoto Protocol Compliant, Non ODP (Ozone Depletion Potential), Non GWP (Global Warming Potential) polyurethane
•Units to have sliding stainless steel lids with recessed handle
•Self-leveling mechanisms shall be adjustable by adding and removing stainless steel extension springs located inside the elevator housing
•Dispenser platform carrier shall be 18gauge stainless steel and removable for cleaning
•6” adjustable stainless steel legs
•Refrigeration system shall be HFC-134A refrigerant
•Expansion valve and pressure control
•9’ cord and plug
•One year parts and 90 day labor standard warranty
Options &
Accessories
•4.00” (10cm) diameter swivel casters (two locking) with corner bumpers (adds 1.75” [4cm] to overall length and depth and reduces overall height by 1.00” [3cm])
•Wrap-around bumpers (adds 1.75” [4cm] to overall length and depth)
•Lid locking device
•Special voltages
•Dial or digital style thermometer
Specifications
Exterior sides shall be 22-gauge stainless steel. Top and corner supports shall be 16-gauge stainless steel, welded, ground and polished into one integral unit.
Interior liner shall be water-tight and constructed of 22-gauge stainless steel with a 1.00” (3cm) I.P.S. drain. Unit shall be insulated with high-density, foamed-in-place environmentally friendly, Kyoto Protocol Compliant, Non ODP (Ozone Depletion Potential), Non GWP (Global Warming Potential) polyurethane insulation with a non-conductive top breaker strip. Refrigerated compartment is equipped with drain plumbed to a drain valve located at the bottom of the counter. Each opening shall have a stainless steel sliding lid recessed handles. Three stainless steel louvers shall be installed in the end and sides of the cabinet to allow proper air flow to the condensing unit.
Each self-leveling mechanism shall be field adjustable by adding or removing stainless steel extension springs in the elevator housing inside the unit. The elevators shall be connected by removable platform carriers constructed of 18-
gauge stainless steel.
Refrigeration system shall use HFC-134a refrigerant. Refrigerant flow shall be controlled by an expansion valve. Cabinet shall maintain 36°F to 40°F (2°C to 4°C) temperture with lids closed for storage. Refrigeration system shall be controlled by a pressure control, located near the condensing unit.
Electrical connections shall be 120 volt, 60 cycle, single phase. Unit shall have a 9’ (2.7m) long electrical cord and NEMA 5-15P plug. Exterior has an ON/OFF switch.
Legs: Unit shall be mounted on 6.00” (15cm) high adjustable stainless steel legs.
NOTE: This equipment is intended for storage and /or display of pre-packaged or bottled products only.
980 S. Isabella Rd. |
Phone: 800-733-8948 or 989-773-7981 |
www.delfield.com |
|
Mt. Pleasant, Michigan 48858 |
|||
Fax: 800-669-0619 |
|||
|
|
||
|
|
|
Dispensers Beverage Or Milk Contained-Self Standing-Free N6/N10/N14