THE PROFESSIONAL ACCESS DRAWERS
Installation Guide
MODELS:
ADR48 ADR30
ADR36 ADR24
A MESSAGE TO OUR CUSTOMERS
Thank you for selecting these DCS by Fisher & Paykel Professional Access Drawers. Because of this product’s unique features we have developed this Installation Guide. It contains valuable information on how to properly install and maintain your new Professional Access Drawers for years of safe and enjoyable use.
To help serve you better, please fill out and submit your Ownership Registration by visiting our website at www.dcsappliances.com and selecting “Customer Service” on the home page and then select “Ownership Registration” or submit the enclosed Ownership Registration Card to the address below. In addition, keep this guide handy, as it will help answer questions that may arise as you use your new Access Drawers.
For your convenience, product questions can be answered by a DCS by Fisher & Paykel Customer Care Representative at 1-888-281-5698, email: support@dcsappliances.com, or by mail:
Fisher & Paykel Appliances, Inc.
Attention: DCS Customer Care
5900 Skylab Road
Huntington Beach, CA 92647
www.dcsappliances.com.
NOTE: Please write the Model and Serial Number on this page for references (located on the inside, top right of the back wall. See Fig. 02.)
MODEL NUMBER
SERIAL NUMBER
WARNING
1.Do Not store or use gasoline or other flammable vapors and liquids inside or in the vicinity of this or any other appliance.
2.An LP cylinder not connected for use shall not be stored inside or in the vicinity of this unit.
FOR YOUR SAFETY
1.Do not allow children or pets to play in or around the Access Drawers.
2.Clean the Access Drawers regularly using a mild dish washing liquid and water.
3.To maintain the exterior appearance, apply a stainless steel polish to the outside surfaces on a regular basis.
4.Sanitize the Access Drawers surfaces each season as necessary.
5.To prevent the formation of mold or mildew, do not store cloth napkins or tablecloths in the Access Drawers for long periods.
6.Cooking utensils that are stored in the Access Drawers should be stored in sealable plastic bags and/or washed each time before re-use.
7.To prevent personal injury or damage to the drawers, do not overload them. The maximum rating per drawer is 75 pounds.
WARNING
•Closing drawers may cause injury to your hands or fingers.
•Always close or open drawers using their handles.
•Be sure to keep hands away from drawer edges when opening or closing drawers.
TABLE OF CONTENTS
SAFETY PRACTICES & PRECAUTIONS |
2 |
MODEL IDENTIFICATION & DIMENSIONS |
3 |
SHIPPING INSPECTION |
3 |
INSTALLATION |
|
Make Cutout and Installing Support Structure |
4 |
Removing Drawers |
5 |
Slide in Access Drawers and Mount to Support Structure |
5 |
Re-installing Drawers |
6-7 |
CARE & MAINTENANCE |
8 |
WARRANTY |
9-10 |
SAFETY PRACTICES AND PRECAUTIONS
1.Begin by insuring proper installation and servicing.
2.Follow the installation instructions in this manual.
3.To extend the service life of your product, be sure to follow the use and care guidelines in this manual.
WARNING:
Do not store items of interest to children above or on the inside of any appliance. Children could be seriously injured if they should climb onto or into the appliance to reach these items.
MODEL IDENTIFICATION & DIMENSIONS
|
|
|
|
|
D |
|
|
|
17-3/4 X 7-1/8 |
|
|
|
|
|
|
|
|
|
11-1/2 |
12-3/16 |
|
|
|
|
|
|
17-3/4 |
X |
X |
|
|
|
|
|
|
X |
19-3/4 |
19-3/4 |
|
|
|
|
H |
|
12-1/2 |
|
|
|
|
|
|
||
17-3/4 X 7-1/8 |
|
|
|
|
|
|
|
|
|
12-3/16 |
|
|
|
|
|
|
|
17-3/4 |
X |
|
|
W |
|
|
|
|
X |
19-3/4 |
|
|
|
|
|
||
|
|
|
|
|
|
|||
12-1/2 |
|
|
|
|
|
|
|
|
|
|
|
F |
|
|
|
|
|
|
|
|
|
DIMENSIONS |
|
|
||
11-1/2 |
12-3/16 |
21-3/8 |
MODEL |
D |
W |
H |
F |
|
|
|
|
|
|
||||
X |
X |
X |
ADR48 |
24-1/4” |
48” |
22” |
1-1/2” |
|
19-3/4 |
19-3/4 |
19-3/4 |
||||||
|
|
|
|
|
||||
|
|
|
ADR36 |
24-1/4” |
36” |
22” |
1-1/2” |
|
|
|
|
ADR30 |
24-1/4” |
30” |
22” |
1-1/2” |
|
|
|
|
ADR24 |
24-1/4” |
24” |
22” |
1-1/2” |
|
Fig. 1 |
Fig. 1a |
|
SHIPPING INSPECTION
1.Inspect the Access Drawers to verify that there is no shipping damage.
2.If any damage is detected, call the shipper and initiate a damage claim. DCS by Fisher & Paykel is not responsible for shipping damage.
NOTE: Do not discard any packing material (box, pallet, straps) until the unit has been inspected.
■Operate the drawers to be sure they glide smoothly.
■Examine the drawer fronts to be sure there are no dents or scratches.
model and serial |
number tag |
Fig. 2
INSTALLATION
MAKE CUTOUT AND INSTALL SUPPORT STRUCTURE
1. Make a cut-out in your cabinet or island with the following dimensions (Fig. 3):
Note:
The cutout of each corner should be 90º for the Access Drawers to fit properly.
Vent*
Vent*
C
Vent*
A B
90º |
Optimal support |
|
locations |
||
|
*Island installation to use minimum of 3 vents providing 10 sq. in. per vent (typical).
Fig. 3
CUTOUT DIMENSIONS
MODEL |
A |
B |
C |
|
(+0,-1/8) |
(+1/8,-0) |
|||
|
|
|||
ADR48 |
46” |
20” |
|
|
|
|
|
|
|
ADR36 |
34” |
20” |
24-1/2” min. |
|
|
|
|
||
ADR30 |
28” |
20” |
(all models) |
|
|
||||
|
|
|
|
|
ADR24 |
22” |
20” |
|
|
|
|
|
|
2.Place 2 X 4s to provide support for the Access Drawers structure in the locations indicated in the figure below (Fig. 4).
3.Board lengths are provided in the table below (Fig. 5).
To ensure proper drawer operation, be sure your support boards are flat & level.
B
8-3/4” 
8-3/4” 
A |
Optimal support locations. |
C
SUPPORT BOARD DIMENSIONS
MODEL |
A |
B |
C |
|
|
|
|
48” |
44” |
1-1/2” |
3-1/2”* min. |
|
|
|
|
36” |
32” |
1-1/2” |
3-1/2”* min. |
|
|
|
|
30” |
26” |
1-1/2” |
3-1/2”* min. |
|
|
|
|
24” |
20” |
1-1/2” |
3-1/2”* min. |
|
|
|
|
*Dependent on application.
Fig. 4 |
Fig. 5 |
4.When installing your support boards, be sure they are level.
5.Check to be certain that the top edges of your boards are level with the bottom edge of the cut-out
(Fig. 6).
Front View (typical)
End View (typical)
For proper support & drawer operation, insure that support boards are level front to back & side to side.
Support Board (typical) |
|
|
Support Boards (typical) |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fig. 6
INSTALLATION
REMOVING DRAWERS
1.Once the unit has been inspected, remove the left drawers by pulling them out until their slider latch is visible. Carefully push the latch down on the left side while pulling up on the right side and pull the drawers completely out of the frame (Fig. 7).
2.To remove the LP tank drawer on the right, pull the drawer out and lift the end by the handle to disengage the rollers (Fig. 8).
3.To prevent damage to surfaces, place the drawers on a stable surface on a protective towel or tablecloth.
Slider latch
Lift
Fig. 7 |
Fig. 8 |
|
SLIDE IN FRAME AND MOUNT TO SUPPORT STRUCTURE
1.With the help of an assistant, lift the unit off of the pallet and slide it into the cabinet cutout. Adjust for level and fit.
2Locate mounting holes on the frame (Fig. 9 and views). Secure the unit using screws suited for the type of cabinet material.
NOTE: Depending on the wall thickness and location of mounting holes, an additional board may be required to properly receive the screws.
3/16" TO 1/2"
MOUNTING SCREWS (not provided)
LOCATIONS
8"
VIEW SHOWING HOLES ON
LEFT AND RIGHT SIDES
AVAILABLE FOR MOUNTING
3/4" |
3/4" |
|
VIEWSHOWINGHOLESONTOPANDBOTTOM
OFFRAMEAVAILABLEFORADDITIONALSUPPORT
Fig. 9
INSTALLATION
RE-INSTALLING DRAWERS
1.Re-install the drawers by extending their guides as shown in fig. 10.
2.While holding the drawer parallel to the cabinet, carefully align & engage the ends of the glides. Slide the drawer about an inch so that the glides are supporting the back of the drawer (Fig. 11).
Drawer Glide properly Engaged.
Fig. 10 |
Fig. 11 |
3.While holding the drawer up by the handle, pull the glides from the drawer cavity out over the drawer glide until they click (Fig. 12).
4.As you push the drawers in, you will encounter moderate resistance. Continue to push the drawer all the way in to complete the engagement process. The drawer will now glide smoothly in & out with light effort (Fig. 13).
Drawer Cavity Glide
Fig. 12 |
Fig. 13 |
INSTALLATION
6. Your LP tank will be installed in the recess provided in the bottom of the right compartment (Fig. 14).
Tank Receptacle
Fig. 14
7.When connecting the LP tank to the gas line be certain that the gas pipe is routed through the recess provided on the top of the right side (Fig. 15). Do not route the gas pipe through the opening in the back of the Access Drawers. Once gas connections are made, test for gas leaks.
8.On models so equipped, install the two (2) racks provided into the opening by sliding them onto the rollers on the sidewalls of the center cavity (Fig. 16).
Rack & Rack Cover
Drain drawer
Gas Pipe Recess
Fig. 15 |
Fig. 16 |
Loading...