Datadelay SMD99C-5050, SMD99C-5050MC2, SMD99C-5060, SMD99C-5060MC2, SMD99C-5075 Datasheet

...
0 (0)
Datadelay SMD99C-5050, SMD99C-5050MC2, SMD99C-5060, SMD99C-5060MC2, SMD99C-5075 Datasheet

 

 

 

SMD99C

 

 

 

 

 

5-TAP, HCMOS-INTERFACED

data

 

 

®

 

3

FIXED DELAY LINE

delay

 

(SERIES SMD99C)

devices, inc.

 

 

 

 

 

FEATURES

Five equally spaced outputs

Designed for surface mounting

Low profile (0.175 maximum height)

Input & outputs fully CMOS interfaced & buffered

10 T2L fan-out capability

PACKAGES

IN

 

 

 

 

VDD

IN

 

1

14

 

VCC

 

 

 

 

 

 

 

 

 

 

 

 

 

1

14

 

N/C

 

2

13

 

N/C

 

 

 

 

 

 

 

12

 

T1

N/C

 

 

12

 

T1

 

 

 

 

 

3

 

 

 

 

 

 

 

T2

 

4

 

T2

 

4

11

 

N/C

 

10

 

T3

 

 

 

 

 

T4

 

6

 

N/C

 

5

10

 

T3

 

 

 

 

 

 

 

T4

 

6

9

 

N/C

GND

 

7

8

 

T5

GND

 

7

8

 

T5

 

 

 

 

 

 

 

 

 

 

 

 

 

Commercial

 

 

 

Military

 

 

 

SMD99C-xx

 

SMD99C-xxMC2

FUNCTIONAL DESCRIPTION

The SMD99C-series device is a 5-tap digitally buffered delay line. The signal input (IN) is reproduced at the outputs (T1-T5), shifted in time by an amount determined by the device dash number (See Table). The total delay of the line is measured from IN to T5. The nominal tap-to-tap delay increment is given by one-fifth of the total delay.

PIN DESCRIPTIONS

IN

Signal Input

T1-T5

Tap Outputs

VDD

+5 Volts

GND

Ground

SERIES SPECIFICATIONS

Minimum input pulse width: 40% of total delay

Output rise time: 8ns typical

Supply voltage: 5VDC ± 5%

Supply current: ICCL = 40μa typical

ICCH = 10ma typical

Operating temperature: 0° to 70° C

Temp. coefficient of total delay: 300 PPM/°C

DASH NUMBER SPECIFICATIONS

Part

Total

Delay Per

Number

Delay (ns)

Tap (ns)

SMD99C-5050

50

± 2.5

10.0 ± 3.0

SMD99C-5060

60

± 3.0

12.0 ± 3.0

SMD99C-5075

75

± 4.0

15.0 ± 3.0

SMD99C-5100

100 ± 5.0

20.0 ± 3.0

SMD99C-5125

125 ± 6.5

25.0 ± 3.0

SMD99C-5150

150 ± 7.5

30.0 ± 3.0

SMD99C-5175

175 ± 8.0

35.0 ± 4.0

SMD99C-5200

200

± 10.0

40.0 ± 4.0

SMD99C-5250

250

± 12.5

50.0 ± 5.0

NOTE: Any dash number between 5004 and 5250 not shown is also available.

20% 20% 20% 20% 20%

VDD IN

T1

T2

T3

T4

T5 GND

DDU8C Functional diagram

©1997 Data Delay Devices

Doc #97018

DATA DELAY DEVICES, INC.

1

1/30/97

3 Mt. Prospect Ave. Clifton, NJ 07013

SMD99C

APPLICATION NOTES

HIGH FREQUENCY RESPONSE

The SMD99C tolerances are guaranteed for input pulse widths and periods greater than those specified in the test conditions. Although the device will function properly for pulse widths as small as 40% of the total delay and periods as small as 80% of the total delay (for a symmetric input), the delays may deviate from their values at low frequency. However, for a given input condition, the deviation will be repeatable from pulse to pulse. Contact technical support at Data

Delay Devices if your application requires device testing at a specific input condition.

POWER SUPPLY BYPASSING

The SMD99C relies on a stable power supply to produce repeatable delays within the stated tolerances. A 0.1uf capacitor from VDD to GND, located as close as possible to the VDD pin, is recommended. A wide VDD trace and a clean ground plane should be used.

DEVICE SPECIFICATIONS

TABLE 1: ABSOLUTE MAXIMUM RATINGS

PARAMETER

SYMBOL

MIN

MAX

UNITS

NOTES

DC Supply Voltage

VDD

-0.3

7.0

V

 

Input Pin Voltage

VIN

-0.3

VDD+0.3

V

 

Storage Temperature

TSTRG

-55

150

C

 

Lead Temperature

TLEAD

 

300

C

10 sec

TABLE 2: DC ELECTRICAL CHARACTERISTICS

(0C to 70C, 4.75V to 5.25V)

PARAMETER

SYMBOL

MIN

TYP

MAX

UNITS

NOTES

High Level Output Voltage

VOH

3.98

4.4

 

V

VDD = 5.0, IOH = MAX

 

 

 

 

 

 

VIH = MIN, VIL = MAX

Low Level Output Voltage

VOL

 

0.15

0.26

V

VDD = 5.0, IOL = MAX

 

 

 

 

 

 

VIH = MIN, VIL = MAX

High Level Output Current

IOH

 

 

-4.0

mA

 

Low Level Output Current

IOL

 

 

4.0

mA

 

High Level Input Voltage

VIH

3.15

 

 

V

 

Low Level Input Voltage

VIL

 

 

1.35

V

 

Input Current

IIH

 

 

0.10

μA

VDD = 5.0

Doc #97018

DATA DELAY DEVICES, INC.

2

1/30/97

Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com

Loading...
+ 2 hidden pages