Danby Products Limited, PO Box 1778, Ontario, Canada N1H 6Z9 Danby Products Inc., PO Box 669, Findlay, Ohio, USA 45839-0669
Printed in China (P.R.C.)
WINE COOLER
Owner’s Manual . . . . . . . . . . . . . . . . . . . . . . .1-4
•Safety Instructions
•Installation
•Operation
•Care and Maintenance
REFROIDISSEUR DE VIN
Manuel d'utilisation . . . . . . . . . . . . . . . . . . . . .5-8
•Consignes de sécurité
•Installation
•Fonctionnement
•Soins et entretien
REFRIGERADOR PARA VINOS
Manual del propietario . . . . . . . . . . . . . . . . .9-12
•Instrucciones de seguridad
•Instalación
•Operación
•Cuidado y Mantenimiento
Danby Products Limited, PO Box 1778, Ontario, Canada N1H 6Z9
Danby Products Inc., PO Box 669, Findlay, Ohio, USA 45839-0669
044.11.02
Danby Products Limited |
|
Danby Products Inc. |
PO Box 1778, 5070 Whitelaw Road, |
|
PO Box 669, 101 Bentley Court, |
Guelph, Ontario, Canada N1H 6Z9 |
|
Findlay, Ohio, U.S.A. 45839-0669 |
Telephone: (519) 837-0920 FAX: (519) 837-0449 |
09.02 |
Telephone: (419) 425-8627 FAX: (419) 425-8629 |
1
SAFETY INSTRUCTIONS
SPECIAL INSTRUCTIONS
You must remove the bottom door support on the bottom left hand side of the unit before you can open the door. (See Fig. A)
FIG. A
INSTALLATION INSTRUCTIONS
Remove the exterior and interior packings, wipe the outside thoroughly with a soft dry cloth and the inside with a wet, lukewarm cloth. Avoid placing the cabinet in a narrow recess or near any heat source, direct sunlight, or moisture. Let air circulate freely around the cabinet. Keep the rear of the wine cooler 5 inches away from the wall.
Location
1.Select a place with a strong, level floor.
2.Allow 5 inches of space between the back of the wine cooler and any adjacent wall.
3.Avoid direct sunlight and heat. Direct sunlight may affect the acrylic coating. Heat sources nearby will cause higher electricity consumption.
OPERATION
To avoid vibration, the cabinet must be set level. To start the wine cooler, follow the instruction below. The wine cooler
temperature will vary depending on the quantity of bottles stored and on the frequency with which the door is opened.
LIGHT SWITCH
TEMPERATURE INCREASE
TEMPERATURE DECREASE
LED DISPLAY
FAHRENHEIT MODE
CELSIUS MODE
FAHRENHEIT/CELSIUS SELECTOR
SETTING THE TEMPERATURE:
1. Connect the power cord to a properly grounded outlet. Each time the unit is disconneted and re-connected to a power source, any previous “SET” temperature is erased and the unit defaults to a factory setting of 10C (50F)
NOTE:
FLASHING LED = SET COOLING TEMPERATURE
STEADY STATE LED = INTERNAL CABINET TEMPERATURE
2. Set the desired cooling temperature by pressing the “up/down” arrows adjacent to the thermometer icon. When either button is depressed and released the “SET” temperature will flash in the LED display for approximately 5 seconds. You can only select (change) the “SET” temperature during the flashing LED mode. Each depression of the up/down arrows will increase/decrease the SET temperature by increments of
1 degree. The SET temperature can be adjusted from 6C ~ 14C (43F ~ 57F) After the SET temperature is established, it will continue to flash for 5 seconds then revert back to a steady state LED mode. The steady state LED display will gradually change, (increase/decrease) to reflect the true temperature inside the cabinet.
2